SEARCH · Engineering Papers

Results for “dynamic load testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

All sources NASA NTRS DOE OSTI

DOE OSTI2024

thevenin: An Equivalent Circuit Modeling Package [SWR-24-132]

This package is a wrapper for the well-known Thevenin equivalent circuit model for simulating battery behavior with a focus on ease of use. The model is comprised of a single series resistor followed by any number of parallel RC pairs. The package includes an intuitive "experiment" interface, which simplifies the programming of constant or dynamic current, voltage, and/or power-driven loads, making it ideal for a wide range of applications, from basic tests to complex simulations. It also supports state-of-charge (SOC) and temperature-dependent properties, allowing the model to be more easily calibrated against real cells.

Randall, Corey↗

NASA NTRS1975

Strain gaged struts and data reduction techniques to maximize quality data from spacecraft flight measurements

The flight instrumentation for the Viking project was established to obtain environmental data, and maximize the data obtainable from the limited number of telemetry channels. To achieve these objectives, a set of six struts were strain gaged and calibrated as load cells to obtain a complete force-time history across an interface. The force-time history can be used with an analytical model to calculate the response of any part of the structure above the instrumented interface. Special matched filters were required to reduce the flight data and derive the phase correlated loads. Flight data results from the Viking Dynamic Simulator flown in February 1974 are described in addition to ground test results used to verify the data reduction process.

Day, F. D., III↗

NASA NTRS1976

Thermal and Structural Analysis of Helicopter Transmission Housings Using NASTRAN

The application of NASTRAN to improve the design of helicopter transmission housings is described. A finite element model of the complete forward rotor transmission housing for the Boeing Vertol CH-47C helicopter was used to study thermal distortion and stress, stress and deflection due to static and dynamic loads, load paths, and design optimization by the control of structural energy distribution. The analytical results are correlated with test data and used to reduce weight and to improve strength, service life, failsafety, and reliability. The techniques presented, although applied herein to helicopter transmissions, are sufficiently general to be applicable to any power transmission system.

Howells, R. W.↗

NASA NTRS1981

Determination of load sequence effects on the degradation and failure of composite materials

A theoretical model was established to predict the fatigue behavior of composite materials, with emphasis placed on predictions of the degradation of residual strength and residual stiffness during fatigue cycling. The model parameters were evaluated from three test series including static strength fatigue life and residual strength tests. The tests were applied to two graphite/epoxy laminates. Load sequence effects were emphasized for both laminates and the predicted results agreed quite well with subsequent verification tests. Dynamic as well as static stiffness reduction data were collected by use of a PDP11-03 computer, which performed quite satisfactorily and permitted the recording of a substantial amount of dynamic stiffness reduction data.

Yang, J. N.↗

NASA NTRS1985

Structural load challenges during space shuttle development

The challenges that resulted from the unique configuration of the space shuttle and capabilities developed to meet these challenges are described. The methods and the organization that were developed to perform dynamic loads analyses on the space shuttle configuration and to assess dynamic data developed after design are discussed. Examples are presented from the dynamic loads analysis of the lift-off and maximum dynamic pressure portion of ascent. Also shown are orbital flight test results, for which selected predicted responses are compared to measured data for the lift-off and high-dynamic-pressure times of ascent. These results have generally verified the design analysis. However, subscale testing was found to be deficient in predicting full-scale results in two areas: the ignition overpressure at lift-off and the aerodynamics/plume interactions at high-q boost. In these areas, the results of the flight test program were accommodated with no impact to the vehicle design.

Mackey, A. C.↗

NASA NTRS1985

Bearing Tester Data Compilation Analysis, and Reporting and Bearing Math Modeling

The magnitude and direction of fluid induced torques and forces on the 57 mm bearing cage is considered to be a contributing factor in possible cage instabilities that can produce intermittent high heating in the bearing. Analyses of the fluid forces and torques are presented. Heat generated by viscous fluid work was estimated for two flow diverter configurations and a coolant flow of 10 lbs/sec to support the thermal evaluation of the LOX Bearing Materials Tester. Results of the analysis of the LOX turbopump turbine end bearings are discussed. Coolant velocities for the no. 4 LOX turbopump turbine end bearings were estimated as a function of shaft speed and coolant flow rate. Contact angles and track width data were developed for the 57 mm bearing as functions of shaft speed, and axial and radial loads. The Advanced Dynamics of Rolling Elements (ADORE) computer program was installed on the MSFC UNIVAC 1100 and a test case successfully run. Both the text output and the plotting output were verified. The Bearing Seal and Materials Tester - Test Condition Data Base was developed. The parametric analysis of the operating characteristics of the LOX turbopump pump end bearing using the 45 mm bearing thermal model was begun.

Source record↗

NASA NTRS1960

Landing Characteristics of a Reentry Capsule with a Torus-Shaped Air Bag for Load Alleviation

An experimental investigation has been made to determine the landing characteristics of a conical-shaped reentry capsule by using torus-shaped air bags for impact-load alleviation. An impact bag was attached below the large end of the capsule to absorb initial impact loads and a second bag was attached around the canister to absorb loads resulting from impact on the canister when the capsule overturned. A 1/6-scale dynamic model of the configuration was tested for nominal flight paths of 60 deg. and 90 deg. (vertical), a range of contact attitudes from -25 deg. to 30 deg., and a vertical contact velocity of 12.25 feet per second. Accelerations were measured along the X-axis (roll) and Z-axis (yaw) by accelerometers rigidly installed at the center of gravity of the model. Actual flight path, contact attitudes, and motions were determined from high-speed motion pictures. Landings were made on concrete and on water. The peak accelerations along the X-axis for landings on concrete were in the order of 3Og for a 0 deg. contact attitude. A horizontal velocity of 7 feet per second, corresponding to a flight path of 60 deg., had very little effect upon the peak accelerations obtained for landings on concrete. For contact attitudes of -25 deg. and 30 deg. the peak accelerations along the Z-axis were about +/- l5g, respectively. The peak accelerations measured for the water landings were about one-third lower than the peak accelerations measured for the landings on concrete. Assuming a rigid body, computations were made by using Newton's second law of motion and the force-stroke characteristics of the air bag to determine accelerations for a flight path of 90 deg. (vertical) and a contact attitude of 0 deg. The computed and experimental peak accelerations and strokes at peak acceleration were in good agreement for the model. The special scaling appears to be applicable for predicting full-scale time and stroke at peak acceleration for a landing on concrete from a 90 deg. flight path at a 0 deg. It appears that the full-scale approximately the same as those obtained from the model for the range of attitudes and flight paths investigated.

McGehee, John R.↗

NASA NTRS2001

Dynamic Analysis of a Building Under Rocket Engine Plume Acoustic Load

Studies have been performed to develop finite-element modeling and simulation techniques to predict the dynamic structural response of Building 4010 to the acoustic load from the plume of high-thrust rocket motors. The building is the Test Control Center and general office space for the E-complex at Stennis Space Center. It is a large single span; light-structured building located approximately 1,000 feet from the E-1 test stand. A three-dimensional shell/beam combined model of the building was built using Pro/Engineer platform and imported into Pro/Mechanica for analysis. An Equivalent Shell technique was developed to simplify the highly complex building structure so that the calculation is more efficient and accurate. A deterministic approach was used for the dynamic analysis. A pre-stressed modal analysis was performed to simulate the weight stiffening of the structure, through which about 200 modes ranging from 0 to 35 Hz were identified. In an initial dynamic frequency analysis, the maximum response over the model was found. Then the complete 3-D distributions of the displacement, as well as the stresses, were calculated through a final frequency analysis. The results were compared to a strain gage and accelerometer recordings from rocket engine tests and showed reasonable agreement.

Qian, Z.↗

NASA NTRS2008

NASA Dryden Flight Loads Laboratory

This viewgraph presentation reviews the work of the Dryden Flight Loads Laboratory. The capabilities and research interests of the lab are: Structural, thermal, & dynamic analysis; Structural, thermal, & dynamic ground-test techniques; Advanced structural instrumentation; and Flight test support.

Horn, Tom↗

NASA NTRS2011

NASA Dryden: Flight Loads Lab Capabilities and Mass Properties Testing

This presentation covers the basic capabilities of the Dryden Flight Loads Lab. It also covers in detail the mass properties capabilities of the loads lab, focusing on the recent mass properties testing of the X-48B, and the recent tests of the Dynamic Inertia Measurement method (DIMM). Presentation focuses on the test methods and issues discovered during the mass properties testing of the X-48B leading to the requirement of new instrumentation on all conventional mass properties testing. Presentation also focuses on development of DIMM for replacement of conventional mass properties tests.

Wolfe, David Michael↗

NASA NTRS2014

Repeatability Modeling for Wind-Tunnel Measurements: Results for Three Langley Facilities

Data from extensive check standard tests of seven measurement processes in three NASA Langley Research Center wind tunnels are statistically analyzed to test a simple model previously presented in 2000 for characterizing short-term, within-test and across-test repeatability. The analysis is intended to support process improvement and development of uncertainty models for the measurements. The analysis suggests that the repeatability can be estimated adequately as a function of only the test section dynamic pressure over a two-orders- of-magnitude dynamic pressure range. As expected for low instrument loading, short-term coefficient repeatability is determined by the resolution of the instrument alone (air off). However, as previously pointed out, for the highest dynamic pressure range the coefficient repeatability appears to be independent of dynamic pressure, thus presenting a lower floor for the standard deviation for all three time frames. The simple repeatability model is shown to be adequate for all of the cases presented and for all three time frames.

Hemsch, Michael J.↗

NASA NTRS2018

Wide-field Infrared Survey Telescope (WFIRST): Composite Structure Verification for Operational Temperatures

The Wide-Field Infrared Survey Telescope (WFIRST) mission is the next large astrophysics observatory for NASA after the James Webb Space Telescope and is the top priority mission from the 2010 National Academy of Sciences' decadal survey. The WFIRST Optical Telescope Assembly (OTA) includes inherited composite support structures that were originally designed and tested for room temperature operation; however, the WFIRST mission will require operation at colder temperatures to achieve sufficient sensitivity for the infrared wavelengths. We will present the results and conclusions of testing completed at the coupon and engineering model level to verify that the inherited composite structures will maintain mechanical integrity and performance over the required temperature range. The testing included: (1) characterization testing of constituent material coupons, (2) thermal cycling and static load testing of a representative aft metering structure (AMS) and forward metering structure (FMS), and (3) thermal cycling and dynamic testing of a representative secondary mirror assembly (SMA).

metering↗

NASA NTRSDate not supplied

CFD Simulation of Ignition Overpressure and Plume-Water Interaction in the SLS Scale Model Acoustics Test

The solid rocket boosters (SRBs) on the Space Launch System (SLS) generate powerful ignition overpressure (IOP) waves that can potentially damage the vehicle and surrounding ground structures. Based on historical Shuttle experience, the IOP will be mitigated by utilizing an IOP/Sound Suppression (SS) water system which sprays water in and around the SRB and RS-25 engine plumes. However, the complex multiphase physics of the resulting plume-water interaction can lead to undesirable effects, such as high velocity water spray onto the engine nozzles and SRB nozzle side loads. Prior to launch, insight into this environment can be achieved through scale model testing and predictive computational fluid dynamics (CFD) modeling. The Scale Model Acoustic Test (SMAT) was conducted at Marshall Space Flight Center to provide the data necessary to develop the SLS liftoff acoustic environments by using a 5% scale SLS vehicle, fully integrated with a scaled IOP/SS water system, mobile launcher (ML), and tower. NASA engineers have put forth significant effort in validating the Loci/CHEM-Real Fluids multiphase CFD solver on a wet hold down test from the SMAT series. In this paper, the IOP acoustics and plume-water interactions predicted by the CFD model are compared and validated against the experiment, enabling relatively inexpensive, rapid turnaround for multiphase launch environment analyses to support future flights and design evolutions of SLS and other launch vehicles.

Computational Fluid Dynamics↗

NASA NTRSDate not supplied

Tutorial: Electrified Aircraft Propulsion Approaches for Modeling and Electrical Hardware-in-the-Loop Testing

This tutorial session outlines capabilities made available by the National Aeronautics and Space Administration for testing electrified aircraft propulsion (EAP) hardware and software prior to using turbomachinery. Removing these components from the experimentation process until necessary significantly reduces the development and testing costs and safety risks. Three facilities, the NASA Electric Aircraft Testbed (NEAT) and the Hybrid Propulsion Emulation Rig (HyPER) are unique facilities that provide the following capabilities: (i) the verification of megawatt-scale electrical and electromechanical system components at altitude, (ii) the verification of EAP control systems on sub-scale representative electromechanical architectures. The importance, operation, and specifications of each facility is described with detail. Provided examples of past testing showcase the abilities of each facility. Simple and complex methods for replicating the steady state and dynamical mechanical loading on the electrical power system are discussed

Electrified Aircraft Propulsion↗

NASA NTRS2011

Aeroservoelastic Wind-Tunnel Tests of a Free-Flying, Joined-Wing SensorCraft Model for Gust Load Alleviation

A team comprised of the Air Force Research Laboratory (AFRL), Boeing, and the NASA Langley Research Center conducted three aeroservoelastic wind-tunnel tests in the Transonic Dynamics Tunnel to demonstrate active control technologies relevant to large, exible vehicles. In the first of these three tests, a full-span, aeroelastically scaled, wind-tunnel model of a joined-wing SensorCraft vehicle was mounted to a force balance to acquire a basic aerodynamic data set. In the second and third tests, the same wind-tunnel model was mated to a new, two-degree-of-freedom, beam mount. This mount allowed the full-span model to translate vertically and pitch. Trimmed flight at -10% static margin and gust load alleviation were successfully demonstrated. The rigid body degrees of freedom required that the model be own in the wind tunnel using an active control system. This risky mode of testing necessitated that a model arrestment system be integrated into the new mount. The safe and successful completion of these free-flying tests required the development and integration of custom hardware and software. This paper describes the many systems, software, and procedures that were developed as part of this effort. The balance and free ying wind-tunnel tests will be summarized. The design of the trim and gust load alleviation control laws along with the associated results will also be discussed.

Scott, Robert C.↗

DOE OSTI2021

Additively Manufactured Compliant Hybrid Gas Thrust Bearing for Supercritical Carbon Dioxide Turbomachinery: Design and Proof of Concept Testing

The following paper presents a new type of gas lubricated thrust bearing that utilizes additive manufacturing or also known as direct metal laser melting (DMLM) to fabricate the bearing. The motivation for the new bearing concept is derived from the need for highly efficient supercritical carbon dioxide (sCO2) turbomachinery in the mega-watt power range. The paper provides a review of existing gas thrust-bearing technology, outlines the need for the new DMLM concept, and discusses proof-of-concept testing results. The new concept combines hydrostatic pressurization with individual tilting pads that are flexibly mounted using hermetic squeeze film dampers (HSFD) in the bearing-pad support. This paper describes the thrust-bearing concept and discusses the final design approach. Proof-of-concept testing in air for a 6.8 in. (173 mm) outer diameter thrust gas bearing was performed; with thrust loading, up to 1500 lbs (6.67 kN) and a thrust runner speed of 10krpm (91 m/s tip speed). The experiments were performed with a bent shaft resulting in thrust runner axial vibration magnitudes of 2.9 mils (74 μm) p-p and dynamic thrust loads of 270 lbs (1.2 kN) p-p. In addition, force deflection characteristics and stiffness coefficients of the bearing system are presented for an inlet hydrostatic pressure of 380 psi (2.62 MPa). Results at 10 krpm show that the pad support architecture was able to sustain high levels of dynamic misalignment equaling 6 times the nominal film clearance while demonstrating a unit load-carrying capacity of 55 psi (0.34 Mpa). Gas-film force deflection tests portrayed nonlinear behavior like a hardening spring, while the bearing pad support stiffness was measured to be linear and independent of gas film thickness.

Engineering↗

NASA NTRSDate not supplied

Advanced Modeling of Control-Structure Interaction in Thrust Vector Control Systems

The Space Launch System (SLS) Core Stage (CS) Thrust Vector Control (TVC) system is comprised of 8 mechanical feedback Shuttle heritage Type III TVC actuators and four RS-25 engines, each attached to a Shuttle heritage gimbal block/bearing. Two actuators are used to move each engine in two planes perpendicular to one another (i.e., pitch and yaw). The TVC system design leverages hardware from the Space Shuttle program as well as new hardware designed specifically for the Core Stage. During the development of the SLS TVC system, a family of advanced dynamics models were developed to extend and compliment the simplified quasi-linear “simplex” model historically used for flight control design and stability analysis. The importance of these advanced models became increasingly evident after ambient and hot fire testing of the Core Stage, which revealed a number of findings associated with the dynamic response of the TVC integrated system. Test responses suggested that the TVC did not meet its performance specifications and its step and frequency responses exhibited unexpected departures from prior lab tests and modeled behavior. One driving factor for these results was a higher-than-expected degree of coupling between the TVC system, the engine dynamics, and the Core Stage structure. This paper is the third installment in a seven-paper series surveying the design, engineering, test validation, and flight performance of the Core Stage Thrust Vector Control system. In this paper, a new method of modeling rocket vehicle thrust vectoring servoelastic dynamics is presented. In this approach, the load dynamics are replaced by a detailed finite element model containing both the rigid body and elastic modes. A partitioning technique is used to compute the effective compliance from the modal data and obtain accurate simulation results using a reduced number of generalized coordinates. Coupled backup structure and nozzle attach compliance effects on multiple engines are captured in higher fidelity than with a spring approximation, eliciting novel effects due to the complex load paths involved in the Core Stage structure. Validation of the model is demonstrated using a variety of structural/modal, laboratory, and full-scale hot fire test data.

Launch Vehicles↗

NASA NTRSDate not supplied

Advanced Modeling of Control-Structure Interaction in Thrust Vector Control Systems

Launch Vehicles↗