Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “drying methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

Chitosan Depolymerization and Nanochitosan Production Using a Single Physical Procedure

The many applications of the chitosan biopolymers in the areas of nanotechnology and nanomaterials have led to the need to develop novel techniques suitable for the production of nanochitosan. At present these typically involve the use of chemical agents to form chitosan nanoparticles. Physical, chemical, and enzymatic methods have been described for the depolymerizatiton of chitosan. In this work, evaluation was made of the efficiency of a combination of physical methods, including milling of the raw material and drying of the final chitosan, in order to obtain nanochitosan with low molar mass. The results revealed the effectiveness of the combination of milling the raw material under controlled conditions for 4.5 h and drying of the chitosan by thermal shock, which provided depolymerization of up to 10× and resulted in chitosan with M{sub v} less than 21 kDa and hydrodynamic diameter below 30 nm.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Nanoparticles of La{sub 0.8}Ca{sub 0.2}Fe{sub 0.8}Ni{sub 0.2}O{sub 3-{delta}} perovskite for solid oxide fuel cell application

Polycrystalline samples of La{sub 0.8}Ca{sub 0.2}Fe{sub 0.8}Ni{sub 0.2}O{sub 3-{delta}} (LCFN) with perovskite type structure have been prepared by combustion, freeze drying, citrate-gel process and liquid mix method. The analysis of X-ray powder diffraction indicated that the samples were single phase and crystallized in an orthorhombic (space group, Pnma no. 62) structure. Transmission electron microscopy (TEM) analysis on the synthesized powder at 600 {sup o}C by liquid mix method showed clusters of 150 nm formed by nanoparticles of 20 nm. Electrochemical performance of LCFN cathodes, which are used for intermediate temperature solid oxide fuel cells, were investigated. The polarization resistance was studied using two different electrolytes: Y-doped zirconia (YSZ) and Sm-doped ceria (SDC). The dc four-probe measurement exhibits a total electrical conductivity, over 100 S cm{sup -1} at T {>=} 600 {sup o}C, pointing out that strontium can be substituted for the cheaper calcium cation without destroying the electrochemical properties. Experimental results indicate that nanoparticles have more advantages in terms of smaller particle size and better electrochemical performance.

36 MATERIALS SCIENCE↗

Morphology and Flow Behavior of Cellulose Nanofibers Dispersed in Glycols

Understanding the morphology and flow behavior of cellulose nanofibers (CNFs) dispersed in organic solvents can improve the process of fabricating new cellulose-based nanocomposites. In this study, jute-based 2,2,6,6-tetramethylpiperidinyl-1-oxyl (TEMPO)-oxidized CNFs with two different charge densities (0.64 and 1.03 mmol/g) were dispersed in ethylene glycol (EG) and propylene glycol (PG) using the solvent exchange method. The morphology and dimensions of CNFs in dry and suspension states were characterized using transmission electron microscopy, atomic force microscopy, and small-angle X-ray scattering techniques. The results showed that the cross-sectional dimensions remained the same in different solvents. Rheological measurements showed that CNF suspensions in water or glycol (EG and PG) behaved similar to typical polymer solutions with a solvent-independent overlap concentration corresponding to the crowding factor of about 14. Moreover, a thixotropic behavior was found in the concentrated CNF/glycol systems as determined in typical CNF aqueous suspensions. The fact that TEMPO-oxidized CNFs can be well dispersed in organic solvents opens up new possibilities to improve the CNF–polymer matrix blending, where the use of a viscous solvent can delay the transition to turbulence in processing and improve the control of fiber orientation because of a slower Brownian diffusive motion.

36 MATERIALS SCIENCE↗

Effect of Carbon Deposition on the Oxidation Rate of Copper/Bentonite in the Chemical Looping Process

The presented work is part of the Industrial Carbon Management Initiative (ICMI) on the development of metal oxide oxygen carriers for use in the chemical looping combustion process. An oxygen carrier, CuO/bentonite (60:40%), was reacted with methane gas and then oxidized in air. The change in weight and reaction gas concentrations were measured using a thermogravimetric analyzer (TGA) equipped with a real-time gas analyzer. The reduction–oxidation cycle was conducted within the temperature range of 750–900 °C for 10 cycles, using 20, 50, and100% CH{sub 4} concentrations in N{sub 2} for the reduction segment and dry air for the oxidation segment. Several analysis methods were evaluated to fit the oxidation of reduced CuO (i.e., Cu) data over the complete conversion range with suitable rate expressions derived from existing models for oxidation, including the shrinking core model (diffusion and reaction control), first- and second-order reaction rates, parallel and series reaction mechanisms, and Johnson–Mehl–Avrami (JMA) rate. The best agreement between the experimental data and the models of the Cu oxidation was accomplished using the JMA model. The reactivity of the oxygen carrier during the oxidation reactions was affected by the CH{sub 4} concentration as well as the temperature. The rate of fractional uptake of oxygen onto the carrier decreased as the temperature increased, contrary to expectations and indicative that the mechanism is changing during the test. Analysis of the exit gas provided evidence of carbon deposition on the reduced sorbent particle and resulted in the CO{sub 2} product upon oxidation. The oxidation of this carbon releases significant heat that is capable of changing the particle morphology (Zhu, Y.; Mimura, K.; Isshiki, M. Oxid. Met. 2004, 62, 207-222). On the basis of experimental results, the overall reaction process in the fuel reactor may be considered to consist of the decomposition of CH{sub 4} into C and H{sub 2} and reduction of CuO/bentonite by the resulting H{sub 2} and the parallel reaction of CH{sub 4} with CuO/bentonite. The extent of carbon deposition in the carrier particle increased with an increasing temperature and CH{sub 4} concentration. This deposited carbon not only leads to CO{sub 2} release from the oxidation reactor but, more importantly, causes degredation of the carrier capacity and its reactivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Sustainable energy and fuels from biomass: a review focusing on hydrothermal biomass processing

Fossil fuels are being replaced with renewable energy resources (biomass and biomass waste, solar, geothermal, wind, etc.) to ensure sustainable development, reduce the dependence on fossil fuels, address environmental challenges including climate change. Today, biomass produces 5 × 10 19 kJ of energy/year, which corresponds to 10% of the annual global energy consumption. Considering the variety of biomass resources, this value is predicted to reach 150 × 10 19 kJ by 2050. Biomass may become even more important for use as an energy resource and chemical raw material in the 21st century. Hydrothermal biomass conversion stands out as a promising and alternative technology. Methods such as traditional gasification and pyrolysis require dry biomass. Hydrothermal techniques have been developed to eliminate the cost and time required for drying biomass. The purpose of this process is to decompose biomass with a high moisture content into small molecules and reduce its oxygen content to obtain liquid fuels or valuable chemicals. Finally, this review presents the current and future state of energy, energy sources, biomass properties and biomass conversion technologies with a focus on hydrothermal technologies.

09 BIOMASS FUELS↗

Remote Sensing of Sea Salt Aerosol below Trade Wind Clouds

Abstract Sea salt aerosol in the boundary layer below shallow cumulus clouds is remotely observed with a Ka-band cloud radar at the Barbados Cloud Observatory and is detected in 76% of the measurements over 1 year. Carried by convection, sea salt particles with a diameter larger than 500 nm show an upward motion of 0.2 m s−1 below shallow cumulus clouds for a 2-day case study. Caused by an increasing relative humidity with increasing altitude, the sea salt particles become larger as they move closer to the cloud base. By using combined measurements of a Ka-band cloud radar and a Raman lidar, the retrieved equivolumetric diameter of the hygroscopically grown sea salt particles is found to be between 6 and 11 μm with a total number concentration of 20 cm−3 near cloud base. Assuming a fixed shape parameter, a size distribution of sea salt particles under high-relative-humidity conditions below cloud base is estimated and agrees with measurements taken by a dry-deposition sampler and online aerosol observations. The methods outlined in this paper can be used in future studies to get a better understanding of the vertical and temporal sea salt distribution in the boundary layer and sea salt aerosol–cloud interaction processes.

54 ENVIRONMENTAL SCIENCES↗

NEAMS Update: Quarterly Report for October - December 2011

The Advanced Modeling and Simulation Office within the DOE Office of Nuclear Energy (NE) has been charged with revolutionizing the design tools used to build nuclear power plants during the next 10 years. To accomplish this, the DOE has brought together the national laboratories, U.S. universities, and the nuclear energy industry to establish the Nuclear Energy Advanced Modeling and Simulation (NEAMS) Program. The mission of NEAMS is to modernize computer modeling of nuclear energy systems and improve the fidelity and validity of modeling results using contemporary software environments and high-performance computers. NEAMS will create a set of engineering-level codes aimed at designing and analyzing the performance and safety of nuclear power plants and reactor fuels. The truly predictive nature of these codes will be achieved by modeling the governing phenomena at the spatial and temporal scales that dominate the behavior. These codes will be executed within a simulation environment that orchestrates code integration with respect to spatial meshing, computational resources, and execution to give the user a common 'look and feel' for setting up problems and displaying results. NEAMS is building upon a suite of existing simulation tools, including those developed by the federal Scientific Discovery through Advanced Computing and Advanced Simulation and Computing programs. NEAMS also draws upon existing simulation tools for materials and nuclear systems, although many of these are limited in terms of scale, applicability, and portability (their ability to be integrated into contemporary software and hardware architectures). NEAMS investments have directly and indirectly supported additional NE research and development programs, including those devoted to waste repositories, safeguarded separations systems, and long-term storage of used nuclear fuel. NEAMS is organized into two broad efforts, each comprising four elements. The quarterly highlights October-December 2011 are: (1) Version 1.0 of AMP, the fuel assembly performance code, was tested on the JAGUAR supercomputer and released on November 1, 2011, a detailed discussion of this new simulation tool is given; (2) A coolant sub-channel model and a preliminary UO{sub 2} smeared-cracking model were implemented in BISON, the single-pin fuel code, more information on how these models were developed and benchmarked is given; (3) The Object Kinetic Monte Carlo model was implemented to account for nucleation events in meso-scale simulations and a discussion of the significance of this advance is given; (4) The SHARP neutronics module, PROTEUS, was expanded to be applicable to all types of reactors, and a discussion of the importance of PROTEUS is given; (5) A plan has been finalized for integrating the high-fidelity, three-dimensional reactor code SHARP with both the systems-level code RELAP7 and the fuel assembly code AMP. This is a new initiative; (6) Work began to evaluate the applicability of AMP to the problem of dry storage of used fuel and to define a relevant problem to test the applicability; (7) A code to obtain phonon spectra from the force-constant matrix for a crystalline lattice has been completed. This important bridge between subcontinuum and continuum phenomena is discussed; (8) Benchmarking was begun on the meso-scale, finite-element fuels code MARMOT to validate its new variable splitting algorithm; (9) A very computationally demanding simulation of diffusion-driven nucleation of new microstructural features has been completed. An explanation of the difficulty of this simulation is given; (10) Experiments were conducted with deformed steel to validate a crystal plasticity finite-element code for bodycentered cubic iron; (11) The Capability Transfer Roadmap was completed and published as an internal laboratory technical report; (12) The AMP fuel assembly code input generator was integrated into the NEAMS Integrated Computational Environment (NiCE). More details on the planned NEAMS computing environment is given; and (13) The NEAMS program website (neams.energy.gov) is nearly ready to launch.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Mechanisms of deterioration of nutrients

Methods for improving the quality of freeze-dried foods were investigated. Areas discussed include: (1) microstructure of freeze-dried systems, (2) structural changes in freeze-dried systems, (3) artificial food matrices, and (4) osmotic preconcentration to yield improved freeze-dried products.

Karel, M.↗

The movement of water droplets in clouds around the nose of an atmospheric research aircraft

The dynamic interaction between droplets and the airflow around the hemispherical nose of an aircraft was evaluated. The effect of the aircraft nose on droplet sampling for cloud research is explained. The proportion of different droplet sizes and their concentration at each point around the aircraft nose were determined. In a cloud, interaction between droplets is negligible. Each particle acts, for the calculation of the forces applied to it, as if it is alone in the air. The airflow carrying the droplets, on the average, is not influenced by their presence. The trajectory of each droplet was studied separately after calculating dry airflow. Concentrations were found with a Lagrangian method, using two trajectories computed directly close to one another. Theory confirms that to within 3% experimentally measured concentrations are representative of those in a cloud.

Feuillebois, P.↗

Simple processing method for high-strength silicon carbide

Silicon carbide test bars were made by a simple wet-processing technique. The pressure casting method used the same equipment as conventional dry-pressing, but with a modified die. This casting technique was employed in order to produce test bars with improved strength and smaller fracture flaws than produced by dry-pressing. This was accomplished by eliminating pore clusters which were present in dry-pressed specimens and identified as a common source of failure in SiC MOR test bars.

Hurst, Janet B.↗

Damping and vibration considerations for the design of optical systems in a launch/space environment

Engineering philosophies for the design of optical systems launched into space and operating in a vacuum or cryovacuum environment are reviewed. Particular attention is given to sources of energy dissipation which are usually lumped under a single modal parameter denoted as the equivalent viscous damping coefficient. Caging and/or damping system components or application of viscoelastic materials and/or dry friction devices are considered to be alternative methods for stabilizing instruments sensitive to motion.

Richard, Ralph M.↗

Vacuum powder injector and method of impregnating fiber with powder

A method and apparatus uniformly impregnate stranded material with dry powder such as low solubility, high melt flow polymer powder to produce, for example, composite prepregs. The stranded material is expanded in an impregnation chamber by an influx of air so that the powder, which may enter through the same inlet as the air, penetrates to the center of the stranded material. The stranded material then is contracted for holding the powder therein. The stranded material and powder may be pulled through the impregnation chamber in the same direction by vacuum. Larger particles of powder which do not fully penetrate the stranded material may be combed into the stranded material and powder which does not impregnate the stranded material may be collected and reused.

Working, Dennis C.↗

Covariability in the Monthly Mean Convective and Radiative Diurnal Cycles in the Amazon

The diurnal cycle of convective clouds greatly influences the radiative energy balance in convectively active regions of Earth, through both direct presence, and the production of anvil and stratiform clouds. Previous studies show that the frequency and properties of convective clouds can vary on monthly timescales as a result of variability in the monthly mean atmospheric state. Furthermore, the radiative budget in convectively active regions also varies by up to 7 Wm-2 in convectively active regions. These facts suggest that convective clouds connect atmospheric state variability and radiation variability beyond clear sky effects alone. Previous research has identified monthly covariability between the diurnal cycle of CERES-observed top-of-atmosphere radiative fluxes and multiple atmospheric state variables from reanalysis over the Amazon region. ASVs that enhance (reduce) deep convection, such as CAPE (LTS), tend to shift the daily OLR and cloud albedo maxima earlier (later) in the day by 2-3 hr. We first test the analysis method using multiple reanalysis products for both the dry and wet seasons to further investigate the robustness of the preliminary results. We then use CloudSat data as an independent cloud observing system to further evaluate the relationships of cloud properties to variability in radiation and atmospheric states. While CERES can decompose OLR variability into clear sky and cloud effects, it cannot determine what variability in cloud properties lead to variability in the radiative cloud effects. Cloud frequency, cloud top height, and cloud microphysics all contribute to the cloud radiative effect, all of which are observable by CloudSat. In addition, CloudSat can also observe the presence and variability of deep convective cores responsible for the production of anvil clouds. We use these capabilities to determine the covariability of convective cloud properties and the radiative diurnal cycle.

Dodson, Jason B.↗

Estimation of Sorption Behavior of Europium to Calcium Silicate Hydrate by Thermal Analysis - 20172

High-level radioactive waste generated from reprocessing processes will be disposed in a geological disposal that is deep underground. Calcium silicate hydrate is formed as a secondary mineral in the repository via the reaction of calcium ions leaching from the cement and the silicic acid dissolved from the host rocks. In this study, the sorption behavior of europium, which is also known as a chemical analog of americium, on calcium silicate hydrate was examined. The solid phase was analyzed via thermogravimetry- differential thermal analysis, differential scanning calorimetry, Raman spectroscopy, fluorescence spectroscopy, and fluorescence lifetime analysis. To understand the behavior of calcium silicate hydrate under conditions saturated with groundwater, the study samples were analyzed using the above methods, except for deferential scanning calorimetry, without a drying process. The results of the differential scanning calorimetry analyses showed that the temperatures for the endothermic peaks of calcium silicate hydrate for the lower Ca/Si ratios were larger than those for the higher Ca/Si ratios for coexistent conditions of europium ions. Hence, the relationships of the temperatures of the endothermic peaks and the Ca/Si ratios were reversed by the addition of europium ions. These study results suggest that calcium silicate hydrate can immobilize europium ions, thus preventing the production of colloidal forms. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

"Soiling, Cleaning, and Abrasion: The Results of the Five-Year Photovoltaic Glass Coating Field Study" [Slides]

External contamination ("soiling") of the incident surface is a major limiting factor for solar technologies. A 5-year field glass coupon study was conducted to better understand external contamination and its effects; compare cleaning methods and the use of preventative coatings; and explore the abrasion resulting from cleaning to advise on accelerated abrasion testing. Test sites included the cities of Dubai (UAE), Kuwait City (Kuwait), Mesa (AZ), Mumbai (India), and Sacramento (CA). Through the 5-year cumulative study, dry brush, water spray, and wet sponge and squeegee cleaning methods were compared to no cleaning. Optical microscopy was used to obtain images, including representative color images, grayscale images for object analysis, and oblique images for coating integrity assessment. A thresholding protocol was developed to analyze and distinguish specimens using the ImageJ software. Optical performance was quantified using a spectrophotometer, including comprehensive optical characterization (transmittance, reflectance, and absorptance in addition to forward- and back-scattering). Atomic force microscopy was used to verify the abrasion damage morphology, including the width and depth of surface scratches. Analysis of the results included correlation of optical performance and particle area coverage, rank order (by coating or location), and the acceleration factor for abrasion damage. The efficacy of external cleaning was more readily distinguished from the effectiveness of antisoiling coatings. The acceleration factor for dry brush cleaning of a porous silica coating was found to be on the order of unity.

14 SOLAR ENERGY↗

Chemically Amplified, Dry-Develop Poly(aldehyde) Photoresist

The catalytic decomposition of poly(phthalaldehyde) with a photoacid generator can be used as dry-develop photoresist, where the exposed film depolymerizes into small molecules to allow the development of features via controlled vaporization. Higher temperatures enabled shorter dry-development times, but also promoted faster photoacid diffusion that compromised pattern fidelity. Trihexylamine was used as a base quencher to counteract acid diffusion in a phthalaldehyde-propanal co-polymer photoresist. The propanal co-monomer in the polymer improves the vaporization rate because it has a higher vapor pressure than phthalaldehyde. Addition of the base quencher was found to improve the contrast, pattern fidelity, and ease-of-handling of the dry-develop resist in a direct-write UV lithography tool. The dry-development of 4 μ m features was achieved with no appreciable residue. For large area features, a spatially variable exposure method was used to direct the residue away from the exposed area. The gradient exposure method was used to produce 100 μ m features. Plasma etching after dry-development was also used to achieve residue-free dry-developed patterns. These results show the benefits of incorporating base additives into a dry-develop depolymerizable resist system and highlight the need for addressing residue formation.

Materials Science↗

Control of Ionomer Distribution and Porosity in Roll-to-Roll Coated Fuel Cell Catalyst Layers

As fuel cells transition from the laboratory to industrial production for vehicles and other applications there is a need to understand how manufacturing processes impact the properties and, ultimately, the performance of materials. Roll-to-roll coating enables processing at meters per second speeds with physics that can be quite different from common laboratory coating methods. In this work, we have focused on the coating of catalyst layers for proton exchange membrane fuel cells. Commonly, laboratory samples are prepared using spray coating or hand painting, which effectively coat many thin layers to achieve the desired catalyst layer thickness. This creates catalyst layers with uniform distributions of materials throughout the thickness of the full catalyst layer. In contrast, roll-to-roll methods, like slot die and gravure, coat the catalyst layer as a single wet film. As the film dries, ink constituents are able to segregate, leading to a heterogeneous distribution of materials through the thickness of the layer. It is also known that solvent and drying rate can affect the morphology of the catalyst layer. Thus, there is a need to understand how ink formulation and the drying process influence the distribution of materials and catalyst layer morphology. Here, we have explored the influence of solvent and drying rate on morphology of roll-to-roll coated catalyst layers. We show the development of the Kelvin probe method as a rapid screening technique for qualitative analysis of ionomer distribution. We also utilize nano X-ray computed tomography to visualize electrode structure and to quantify particle-size and pore-size distributions, thickness-dependent ionomer distribution, tortuosity, and effective transport properties. We find that solvent has a strong influence on ionomer distribution, with less of an effect on porosity. Conversely, drying temperature has a strong influence on porosity, but less influence on ionomer distribution. Finally, we utilize in situ fuel cell performance testing and other advanced diagnostics to quantify the impact of catalyst layer properties on fuel cell performance and demonstrate that roll-to-roll coating is capable of coating high performance catalyst layers in multi-meter lengths. have focused on the coating of catalyst layers for proton exchange membrane fuel cells. Commonly, laboratory samples are prepared using spray coating or hand painting, which effectively coat many thin layers to achieve the desired catalyst layer thickness. This creates catalyst layers with uniform distributions of materials throughout the thickness of the full catalyst layer. In contrast, roll-to-roll methods, like slot die and gravure, coat the catalyst layer as a single wet film. As the film dries, ink constituents are able to segregate, leading to a heterogeneous distribution of materials through the thickness of the layer. It is also known that solvent and drying rate can affect the morphology of the catalyst layer. Thus, there is a need to understand how ink formulation and the drying process influence the distribution of materials and catalyst layer morphology. Here, we have explored the influence of solvent and drying rate on morphology of roll-to-roll coated catalyst layers. We show the development of the Kelvin probe method as a rapid screening technique for qualitative analysis of ionomer distribution. We also utilize nano X-ray computed tomography to visualize electrode structure and to quantify particle-size and pore-size distributions, thickness-dependent ionomer distribution, tortuosity, and effective transport properties. We find that solvent has a strong influence on ionomer distribution, with less of an effect on porosity. Conversely, drying temperature has a strong influence on porosity, but less influence on ionomer distribution. Finally, we utilize in situ fuel cell performance testing and other advanced diagnostics to quantify the impact of catalyst layer properties on fuel cell performance and demonstrate that roll-to-roll coating is capable of coating high performance catalyst layers in multi-meter lengths.

30 DIRECT ENERGY CONVERSION↗