Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “directivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Parameter development and characterization of laser powder directed energy deposition of Nb – Alloy C103 for thin wall geometries

This work focuses on the parameter development and microstructural characterization of Nb-based alloy C103 for thin wall structures produced via laser powder – directed energy deposition (LP – DED). Laser power and scanning speeds were varied as part of a design of experiments to identify adequate print parameters. Combinations were evaluated for relative density, porosity, and geometrical accuracy. A combination of a laser power of 1420 W and scanning speed of 14 mm/s resulted in a relative density >99%, exhibited a consistent weld bead profile and was used for further microstructural evaluation. A mix of optical and scanning electron microscopy (SEM) revealed small, slightly elongated grains along the edges and large epitaxial grains in the central region along the Build – Transverse view. Scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) analysis revealed Hf rich columnar cells in the center that transition into an evenly spaced cellular structure towards the edges of the built sample. Electron backscatter diffraction (EBSD) scans show a sharp [001] texture when looking at the cross section of the sample along the build direction. The Build – Scan view revealed a zig – zag pattern that follows the back – and – forth deposition strategy that was used. Finally, microhardness measurements were taken in the as – built (AB) and stress relieved (SR) conditions to baseline preliminary mechanical properties. The AB condition exhibited a large amount of scatter in the data and averages up to 11% larger than the SR condition. The reduction in scatter upon applying the SR cycle are indicative of a large concertation of dislocations present in the AB condition.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Correlating energy density induced residual stress, porosity, and mechanical property variations in directed energy deposition using neutron diffraction and imaging techniques

In a directed energy deposition (DED) process, the energy density deposited into the materials drives the structure and properties. The energy density is influenced by several printing parameters, such as laser power, hatch spacing, scanning speed, etc. In this study, 316L stainless steels samples were fabricated with varying hatch spacing aiming to induce variations in sample microstructure and properties. A combination of techniques including engineering neutron diffraction, neutron computed tomography, and tensile testing, were employed to correlate the structure and macroscopic properties. Porosity was predominantly observed at the bottom of the deposited materials and was effectively reduced by decreased hatch spacing. Correlatively, compressive residual stress was observed at the bottom of the specimens, while internal stress is largely determined by the hatch spacing. The residual stress in general decreases as the hatch spacing decreases. The maximum ultimate tensile strength (UTS) was found to increase from 517.4 to 528.6 MPa with a strain increased from 0.847 to 0.897 as the hatch spacing decreased from 0.45 to 0.42 mm. However, further increase in energy density by reducing the hatch spacing resulted in a significant decrease in UTS (as low as 452 MPa). This work provides new insights from bulk non-destructive techniques into correlating energy density induced residual stress, porosity, and mechanical property variations in directed energy deposition.

316L stainless steel↗
DOE OSTI2024

Navigating the Use of Direct Current in Residential Settings: Merits and Obstacles

This review paper provides an in-depth analysis of the role of Direct Current (DC) power systems in residential settings, focusing on their safety, efficiency, and environmental advantages. It recognizes the significant contribution of the residential sector to global carbon dioxide emissions and explores how DC power systems can help mitigate these effects. The paper traces the historical evolution of DC power, its resurgence with renewable energy technologies, and the advancements in power electronics that facilitate its integration. Emphasizing the efficiency and safety benefits, especially in low-voltage applications, the paper highlights the seamless integration of DC systems with inherently DC-generating renewable sources like solar PV and wind. The review discusses the critical role of converter technologies in the transition to DC power and examines the compatibility of DC systems with energy storage solutions, underscoring their potential for enhanced energy management. It also addresses the environmental impacts of adopting DC power, aligning with global carbon reduction efforts. The paper analyzes regional case studies, exploring practical applications and outcomes, and addresses challenges such as the need for standardization. It concludes with recommendations for stakeholders and future research directions, emphasizing the economic, technological, and environmental aspects of DC power systems. Overall, the paper presents DC power as a viable and sustainable option for residential energy conservation, contingent upon ongoing technological progress, supportive policies, and standardization.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

Separation of volatile organic contaminants from water using a direct-contact dehumidifier: An experimental study and modeling

A packed-bed, direct-contact dehumidifier (PB-DCD) has been developed to selectively condense water from a gaseous mixture of organic contaminants. In this process, hot air is humidified by mixing with wastewater vapor in a static mixer and is dehumidified by subcooled fresh water passing through the PB-DCD in a counter-current configuration. The goal of this study is to understand the relationship between various operating parameters and how they affect separation of isopropyl alcohol (IPA) from the gaseous mixture with the purpose of expanding the investigation to other contaminants in the future. The process has been successfully used to separate IPA from wastewater. Different parameters including the concentration of IPA in water, feed temperature, air-to-vapor ratio, and cooling-water-to-vapor mass ratio, as well as residence time were examined to determine their influence on contaminant separation and clean water recovery rate. The Buckingham Pi theorem was applied to reduce the number of studying variables by generating non-dimensional groups. Experiments were performed to determine the relationship between the non-dimensional parameters and model mass transfer in the system. Mass transfer coefficients for multicomponent gaseous mixture condensation in a packed-bed direct contact condenser column are calculated and a modified correlation of mass transfer is developed. The parameters of the mass transfer model are obtained from operating conditions of the PB-DCD, stream conditions and thermodynamic properties. A modified Sherwood correlation is developed to predict IPA separation from a gaseous mixture consisting of air, water, and IPA. The modified Sherwood correlation is applied to successfully predict the Sherwood number with a mean absolute error equal to 6.6 %. According to the experimental results, the maximum IPA separation achieved was 76.3 %, which corresponds to a water recovery rate of 58.7 %.

42 ENGINEERING↗
DOE OSTI2025

Direct ink writing of shear exfoliated two-dimensional nanomaterial- elastomeric multifunctional nanocomposite

Direct ink writing (DIW) of polymer nanocomposites with high loadings of two-dimensional (2D) nanofillers (graphene and hexagonal boron nitride (hBN)) is challenging because of potential clogging, use of hazardous solvents, and agglomeration. Here, in this work, a shear exfoliation and sieving method to prepare DIW ink with high loading of nanofillers produced from low-cost bulk layered materials such as graphite and bulk hBN powder for successful DIW printing without the use of any solvents, binders, or plasticizers. The single-step exfoliation technique resulted in a composite with substantial layer reduction along the c-axis, as confirmed by SEM, TEM, XRD, and Raman analysis. Incorporating exfoliated graphene (40 wt%) increased viscosity by ∼6 orders of magnitude due to enhanced particle–matrix interactions, leading to pronounced yield stress behavior and a yield stress of approximately 1598 Pa, which enabled excellent shape retention during extrusion. Using the DIW technique, porous structures such as desalination membranes, self-sensing bone scaffolds, thermal management coating, and serpentine strain sensors were fabricated. When tested in a direct contact membrane distillation setup, the fabricated membrane demonstrated a promising permeate flux of 21.85 Lm −2 h −1 and a salt rejection of 74.3 %. The fabricated serpentine sensor exhibited stable signal variations under cyclic tensile loading, with a working range of 0–200 % strain and a maximum gauge factor of 43,735. A cell culture test using the printed bone scaffold demonstrated promising cell attachment and proliferation. The DIW printed hBN nanocomposite exhibited reversible shape change under heat, demonstrating potential 4D printing capability and efficient thermal management when exposed to high heat or flame.

Desalination↗
DOE OSTI2026

Measurement of kaon directed flow in Au+Au collisions in the high baryon density region

Rapidity-odd directed flow v 1 measurements are presented for $K^±$ and $K^0_S$ in Au + Au collisions for $\sqrt{s_{NN}}$ from 3.0 to 3.9 GeV with the STAR experiment. For comparison, v 1 of π ± , protons, and Λ from the same collisions are also discussed. The mid-rapidity v 1 slope dv 1 /dy| y=0 for protons and Λ is positive in these collisions. On the other hand, v 1 slope of kaons exhibits a strong dependence: negative at p T < 0.6 GeV/c and positive at higher p T . A similar p T dependence is also evident for the v 1 slope of charged pions. Compared to the spectator-removed calculations in Au+Au collisions at $\sqrt{s_{NN}}$ = 3.0–3.9 GeV, the JAM model demonstrates a pronounced shift of the v 1 slopes of mesons towards the negative direction. It suggests that the shadowing effect of the spectators plays an important role in the observed kaon anti-flow at low p T in the high baryon density region of non-central collisions.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2023

Determination of the regeneration energy of direct air capture solvents/sorbents using calorimetric methods

Regeneration energy and recyclability are important parameters that dictate the viability of a CO 2 direct air capture (DAC) process. In this study, differential scanning calorimetry (DSC) is used in conjunction with thermogravimetric analysis (TGA) and Fourier Transform Infrared Spectroscopy (FTIR) to evaluate the regeneration energy required for CO 2 -loaded 3 M aqueous potassium sarcosinate (K-SAR) solvent and crystalline methyl-glyoxal-bisiminoguanidine (MGBIG) sorbent. Based on calorimetric measurements, for aqueous K-SAR, the sensible heat amounts to 1.5 GJ/tCO 2 and the enthalpy of desorption is estimated at 3.68 GJ/tCO 2 . The total energy of regeneration will also include the enthalpy of solvent vaporization, which will depend on the thermodynamic conditions and the level of regeneration. For MGBIG, the total regeneration energy required was measured at approximately 7.0 GJ/tCO 2 . Further, FTIR measurements were used to observe CO 2 and H 2 O release during the thermal regeneration process. For K-SAR, CO 2 release is seen to take place at temperatures greater than 80 °C and, for MGBIG, the CO 2 release takes place at temperatures greater than 100 °C. The moderate temperatures required for K-SAR and MGBIG regenerations compared to other DAC solvents/sorbents suggest that low-cost sources of heat, such as geothermal heat, could potentially be used for regeneration to drive down the cost of direct air capture.

42 ENGINEERING↗
DOE OSTI2023

An effective air–liquid contactor for CO 2 direct air capture using aqueous solvents

Here, the development of a cost-effective, corrosion resistant, high-flux direct air capture (HiDAC) contactor for a solvent-based direct air capture (DAC) process is reported. Literature technoeconomic analyses suggest that the air–liquid contactor can cost over 20 % of the overall DAC plant’s annualized capital costs. To bring down the overall cost of DAC, it is imperative that an effective contactor is developed. A hybrid contactor consisting of a commercial polyvinylchloride structured packing enhanced with stainless-steel 410 random packing has been developed to provide a high surface area for air–liquid contact. The contactor geometry, wettability, corrosion resistance, pressure drop, along with its CO 2 uptake efficiency, CO 2 uptake rates, and extended loading potential using potassium sarcosinate solutions are investigated. Results show that the HiDAC contactor has a relatively high specific surface area (885 m 2 /m 3 ), which allows for CO 2 uptake efficiencies of up to 75 % and capture rates of up to 550 g of CO 2 per day for a 0.3 × 0.25 × 0.3 m contactor. The contactor also exhibits high levels of wettability and corrosion resistance with amino acid-based DAC solvents. A CO 2 uptake model was developed, and modeling results are compared to experimental data to simulate and predict the performance of the contactor in a DAC process using potassium sarcosinate solvent. The system’s overall mass transfer coefficient and theoretical pressure drop were also calculated, and these results were compared to DAC data found in literature. The results presented indicate that the HiDAC contactor is well suited for DAC due to its high specific surface area, resistance to corrosion, and high degree of wettability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Comparison of direct and CO 2 -oxidative dehydrogenation of propane

Propane dehydrogenation to propylene has received increasing attention due to the fast growth in propylene demand and the exploration of shale gas containing propane. Direct dehydrogenation of propane (DDHP) offers high propylene selectivity but is limited by quick deactivation due to coke formation. CO 2 -assisted oxidative dehydrogenation of propane (CO 2 -ODHP) can consume CO 2 and meanwhile reduce coke deposition via the reverse Boudouard reaction. Here in the current review, direct and CO 2 -assisted dehydrogenation of propane has been compared from three aspects: reaction mechanisms, catalyst compositions, and CO 2 footprint analysis. As the average CO 2 emissions from electricity generation decrease due to the utilization of renewable energy, CO 2 -ODHP potentially leads to a net-negative CO 2 footprint while DDHP cannot.

58 GEOSCIENCES↗
DOE OSTI2020

The performance evaluation of direct detection electron energy-loss spectroscopy at 200 kV and 80 kV accelerating voltages

Direct electron detectors (DeDs) have been widely used for imaging studies because of their higher beam sensitivity, lower noise, improved pixel resolution, etc. However, there have been limited studies related to the performance in spectroscopic applications for the direct electron detection. Hereby, taking the advantage of the DeD installed on a high-performance electron energy-loss spectrometer, we systematically studied the performance of a DeD (Gatan's K2 IS) fitted on an aberration-corrected transmission electron microscope (TEM) equipped with an electron monochromator. Using SrTiO3 as the model system, the point spread function in the zero-loss region of the spectrum and the performance for core loss spectroscopy have been investigated under both 200 kV and 80 kV operating conditions. We demonstrate that the K2 detector can achieve an overall better performance at 200 kV than a charge coupled device (CCD) detector. At 80 kV, the K2 DeD is still better than a CCD, except for the relative broad tails of the zero-loss peak. The signal-to-noise ratio is very close for DeD and CCD under 80 kV. Based on our data obtained at different operating voltages, it is clear that DeD will benefit the microscopy community and boost the development of cutting-edge materials science studies by pushing the frontiers in electron energy-loss spectroscopy.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Engineering Directionality in Quantum Dot Shell Lasing Using Plasmonic Lattices

In this paper, we report how the direction of quantum dot (QD) lasing can be engineered by exploiting high-symmetry points in plasmonic nanoparticle (NP) lattices. The nanolaser architecture consists of CdSe-CdS core-shell QD layers conformally coated on two-dimensional square arrays of Ag NPs. Using waveguide-surface lattice resonances (W-SLRs) near the Δ point in the Brillouin zone as optical feedback, we achieved lasing from the gain in CdS shells at off-normal emission angles. Changing the periodicity of the plasmonic lattices enables other high-symmetry points (Γ or M) of the lattice to overlap with the QD shell emission, which facilitates tuning of the lasing direction. We also increased the thickness of the QD layer to introduce higher order W-SLR modes with additional avoided crossings in the band structure, which expands the selection of cavity modes for any desired lasing emission angle.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2023

Polyvinyl Alcohol Anion Exchange Resin Composite Membrane with Co@Cu Core–Shell Particles for Direct Borohydride Fuel Cell Applications

We report a polyvinyl alcohol anion exchange resin composite membrane, functionalized with Co and Cu ions, is reported for use in direct borohydride fuel cells (DBFCs). The CoCu-functionalized membrane has a 30.5% lower fuel permeability than that of a blank membrane. Meanwhile, the cell performance of the DBFC can also be improved by employing the CoCu-functionalized membrane, reaching a maximum power density of 304 mW·cm –2 at 60 °C. High-resolution fluorescence images directly demonstrate the formation of Cu/Co core–shell structure microparticles in the CoCu membrane, which not only reduces the Co content but also increases the active surface area of Co species in CoCu-functionalized membranes, resulting in the improvement of cell performance.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Sub-100 mA/cm 2 CO 2 -to-CO Reduction Current Densities in Hierarchical Porous Gold Electrocatalysts Made by Direct Ink Writing and Dealloying

While most research efforts on CO 2 -to-CO reduction electrocatalysts focus on boosting their selectivity, the reduction rate, directly proportional to the reduction current density, is another critical parameter to be considered in practical applications. This is because mass transport associated with the diffusion of reactant/product species becomes a major concern at a high reduction rate. Nanostructured Au is a promising CO 2 -to-CO reduction electrocatalyst for its very high selectivity. However, the CO 2 -to-CO reduction current density commonly achieved in conventional nanostructured Au electrocatalysts is relatively low (in the range of 1–10 mA/cm 2 ) for practical applications. In this work, we combine direct ink writing-based additive manufacturing and dealloying to design a robust hierarchical porous Au electrocatalyst to improve the mass transport and achieve high CO 2 -to-CO reduction current densities on the order of 64.9 mA/cm 2 with CO partial current density of 33.8 mA/cm 2 at 0.55 V overpotential using an H-cell configuration. Although the current density achieved in our robust hierarchical porous Au electrocatalyst is one order of magnitude higher than the one achieved in conventional nanostructured electrocatalysts, we found that the selectivity of our system is relatively low, namely 52%, which suggests that mass transport remains a critical issue despite the hierarchical porous architecture. We further show that the bulk dimension of our electrocatalyst is a critical parameter governing the interplay between selectivity and reduction rate. In conclusion, the insights gained in this work shed new light on the design of electrocatalysts toward scale-up CO 2 reduction and beyond.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Polydiallylammonium-Polysulfone Multiblock Copolymers for Moisture-Swing Direct Air Capture of Carbon Dioxide

Polysulfones are an important class of materials for a variety of applications due to their excellent strength and thermal stability. Quaternary ammonium polymers are also useful materials due to their ion exchange properties, and such materials with alkaline counterions have been used to capture carbon dioxide (CO 2 ) from ambient air through a moisture-driven mechanism. Herein, we design sulfone-based multiblock copolymers containing ammonium functionalities and demonstrate their potential for CO 2 capture. Specifically, a series of multiblock copolymers containing both polydiallyldimethylammonium (PDADMA) and polysulfone (PSf) blocks were synthesized. PSf blocks provide mechanical integrity, while the PDADMA blocks enable the direct air capture of CO 2 . Multiblock copolymers were synthesized at high yield, and PDADMA(OH)-PSf copolymer films with good flexibility and strength were formed with IECs of 424 μmol/g (17 mol % PDADMA(OH)), 1407 μmol/g (44 mol % PDADMA(OH)), and 1726 μmol/g (50 mol % PDADMA(OH)). Thermogravimetric analysis was used to determine that all films are thermally stable up to 345 °C. Differential scanning calorimetry revealed that the 17 and 44 mol % functionalized PDADMA(OH)-PSf multiblock copolymers showed one T g at 185 °C and 50 mol % PDADMA(OH)-PSf polymer showed a T g at 183 °C and a second T g at 16 °C. Atomic force microscopy showed that the multiblock polymers exhibit disordered phase separation. Furthermore, the copolymer materials displayed moisture-swing direct air capture of CO 2 , opening up pathways to utilize polymer architecture and chemistry to tailor the properties of promising sorbents.

42 ENGINEERING↗
DOE OSTI2025

In Situ Surface Reconstruction via Lithium Residue Regulation for Direct Recycling of Ni-Rich Cathodes

Surface stability is crucial for the long cycling performance of Ni-rich cathodes, as it dictates and governs side reactions, preserves crystal integrity, and mitigates capacity degradation during cycling. For spent Ni-rich cathodes targeted for one-step direct recycling, constructing a robust and stable surface is particularly challenging because prior cycling induces severe structural and morphological degradation. Here, in this study, we introduce an in situ surface reconstruction strategy that converts surface lithium residues into a protective layer via a direct liquid-phase coating with ammonium dihydrogen phosphate (ADP). During the process, residual lithium remaining after the hydrothermal relithiation is removed, while a conformal lithium phosphate (Li 3 PO 4 , LPO) layer is formed to act as both a chemical barrier and a structural stabilizer. This dual function enhances cycling stability and rate capability in regenerated cathodes, and the approach is applicable to various Ni-rich compositions including spent LiNi 0.6 Co 0.2 Mn 0.2 O 2 (NCM622) and scrap LiNi 0.866 Mn 0.066 Co 0.05 Al 0.018 O 2 (NCMA). Its scalability and compositional versatility make it a promising route for sustainable regeneration of high-performance cathode materials.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Continuous Directed Evolution of a Short-Lived Plant Histidinol Dehydrogenase

Enzyme protein turnover accounts for about half the maintenance energy budget in plants. Slowing turnover i.e., extending the effective working life (Catalytic Cycles till Replacement, CCR) of short-lived enzymes is thus a rational strategy to conserve energy and carbon and raise crop productivity. Arabidopsis histidinol dehydrogenase (HDH) is a short-lived enzyme that can sustain lifeshortening damage from its aminoaldehyde reaction intermediate. We used the yeast OrthoRep continuous directed evolution system in a his4 Δ strain to raise cumulative HDH function and, by proxy, lifespan as functional enzymes, by selecting for growth rate while tapering histidinol concentration and escalating that of the inhibitor histamine. Improved HDH variants carried diverse nonsynonymous mutations and ranged 20-fold in level. Improved HDH performance was associated with higher HDH abundance in some cases and with greater catalytic efficiency or histamine resistance in others. These findings indicate that OrthoRep-based directed evolution can extend enzyme working life in vivo in addition to, as expected, altering kinetic properties.

directed evolution↗
DOE OSTI2021

Direct Optical Lithography of Colloidal Metal Oxide Nanomaterials for Diffractive Optical Elements with 2π Phase Control

Spatially patterned dielectric materials are ubiquitous in electronic, photonic, and optoelectronic devices. These patterns are typically made by subtractive or additive approaches utilizing vapor-phase reagents. On the other hand, recent advances in solution-phase synthesis of oxide nanomaterials have unlocked a materials library with greater compositional, microstructural, and interfacial tunability. However, methods to pattern and integrate these nanomaterials in real-world devices are less established. In this work, we directly optically pattern oxide nanoparticles (NPs) by mixing them with photosensitive diazo-2-naphthol-4-sulfonic acid and irradiating with widely available 405 nm light. We demonstrate the direct optical lithography of ZrO 2 , TiO 2 , HfO 2 , and ITO NPs and investigate the chemical and physical changes responsible for this photoinduced decrease in solubility. Micron-thick layers of amorphous ZrO 2 NPs were patterned with micron resolution and shown to allow 2 pi phase control of visible light. We also show multilayer patterning and use it to fabricate features with different thicknesses and distinct structural colors. Upon annealing at 400 degrees C, the deposited ZrO 2 structures have excellent optical transparency across a wide wavelength range (0.3-10 mu m), a high refractive index (n = 1.84 at 633 nm), and are optically smooth. We then fabricate diffractive optical elements, such as binary phase diffraction gratings, that show efficient diffractive behavior and good thermal stability. Different oxide NPs can also be mixed prior to patterning, providing a high level of material tunability. This work demonstrates a general patterning approach that harnesses the processability and diversity of colloidal oxide nanomaterials for use in photonic applications.

2𝜋 phase shift↗
DOE OSTI2023

Interface synergism and engineering of Pd/Co@N-C for direct ethanol fuel cells

Direct ethanol fuel cells have been widely investigated as nontoxic and low-corrosive energy conversion devices with high energy and power densities. It is still challenging to develop high-activity and durable catalysts for a complete ethanol oxidation reaction on the anode and accelerated oxygen reduction reaction on the cathode. The materials’ physics and chemistry at the catalytic interface play a vital role in determining the overall performance of the catalysts. Herein, we propose a Pd/Co@N-C catalyst that can be used as a model system to study the synergism and engineering at the solid-solid interface. Particularly, the transformation of amorphous carbon to highly graphitic carbon promoted by cobalt nanoparticles helps achieve the spatial confinement effect, which prevents structural degradation of the catalysts. The strong catalyst-support and electronic effects at the interface between palladium and Co@N-C endow the electron-deficient state of palladium, which enhances the electron transfer and improved activity/durability. The Pd/Co@N-C delivers a maximum power density of 438 mW cm -2 in direct ethanol fuel cells and can be operated stably for more than 1000 hours. This work presents a strategy for the ingenious catalyst structural design that will promote the development of fuel cells and other sustainable energy-related technologies.

25 ENERGY STORAGE↗