Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “conditional expectations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Gamma Discriminating Scintillation Screens for Digital Transfer Method Neutron Imaging

A collaborative project between Idaho National Laboratory (INL) and Paul-Scherrer Institute (PSI) is investigating a new type of scintillation screen that uses ZnS scintillator material with a dysprosium neutron converter instead of traditional prompt converters such as 6Li. Such a screen exposed to a neutron beam creates a latent image by neutron activation of the dysprosium in the scintillator screen. The activated screen is transported into a camera box allowing the camera to read a digital image from the photons emitted by the activated scintillation screen. Such an imaging system combines modern camera-based system architecture with the approach of traditional indirect transfer method radiography. The results show for the first time that the combination of dysprosium with a scintillation material like ZnS can produce light which is measurable under common camera-based detection conditions and that neutron radiographic images of reasonable quality can be produced. The resolution was poorer than expected at ~ 300 µm, but is on the order of the desired resolution of 100 µm. Potential improvements and additional converter materials may be investigated in the future that could increase the light output and improve spatial resolution.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2025

Coupling to rotational manifolds to improve gas-phase pump–probe spectroscopic models

The physical picture of gas-phase optical transitions is normally presented as an isolated two-level system balanced by upward and downward processes. Isolated models assume a phenomenological treatment of collisional dephasing but do not strictly account for collisional population exchange with the rotational baths. While this assumption is valid under low-intensity conditions, where excitation is rate-limiting, isolated models can deviate from Beer’s Law at sufficient pressures and monochromatic intensities when both collisional broadening and power broadening are comparable to (or greater than) lifetime broadening, which are not uncommon conditions for cavity enhanced spectroscopies in the mid-IR spectral range. Although this problem has been addressed by rate-equation models for linear absorption measurements, a general treatment for multi-level quantum mechanical models suitable for non-linear absorption measurements (two-photon/two-color/pump–probe) is lacking. Isolated models require physical parameter inputs that disagree with expected values by at least an order of magnitude. These non-physical models undermine the ability to predict non-linear signal strengths under untested conditions and thereby limit the potential to optimize the sensitivity of non-linear spectroscopies and to expand their analytical applications (e.g., new analytes and/or buffer gases, changes in cavity free-spectral-range, changes in intracavity powers or wavelengths, and accurate investigation of physical phenomena). In this study, we derive bath-coupled models for gaseous pump–probe spectroscopy by application of the quantum Lindblad equation and detailed balance. Bath-coupled models are shown to fit data consistently across variations in intensity and agree with all physically expected values.

Cavity ring-down spectroscopy↗
DOE OSTI2023

Cesium Removal from 5.5 and 7.0 M Na AP-105 Using Crystalline Silicotitanate

The Tank Side Cesium Removal (TSCR) system, currently operational by Washington River Protection Solutions LLC (WRPS), prepares initial low-activity Hanford waste tank supernate feeds for the Hanford Waste Treatment and Immobilization Plant (WTP) Low-Activity Waste (LAW) Facility. In addition to entrained solids removal from the supernate, the primary goal of TSCR is to remove cesium-137 ( 137 Cs) by ion exchange, allowing contact handling of the liquid effluent product at the WTP as governed by a waste acceptance criterion (WAC). Specific to 137 Cs, this requirement is < 3.18E-5 Ci 137 Cs/mole of Na. Crystalline silicotitanate (CST) ion exchange media, manufactured by Honeywell UOP, LLC (product IONSIVTM R9140-B), has been selected as the ion exchange media for TSCR. CST is a non-elutable inorganic material that has demonstrated robust chemical, physical, and radiation tolerance while maintaining functionality. However, testing to date on actual tank waste samples has been limited to Na concentrations between 5 and 6 M Na (Fiskum et al. 2019a, 2021b and Westesen et al. 2021a, 2021b, 2022) while actual tank conditions can reach upwards of 9 M Na. Testing with feed from Hanford tank AP-105 incorporated testing at both 5.5 and 7 M Na in order to evaluate the impact of Na concentration on volume of waste processed before reaching the WAC. A 6-L volume of 5.5 M Na AP-105 and an 8-volume of 7 M Na AP-105 was processed through the Radioactive Waste Test Platform system, established at Pacific Northwest National Laboratory to support small-scale waste qualification efforts. The columns consisted of 6- to 9-mL CST beds (CST Lot 2002009604, sieved to screen out >30-mesh particles) placed in 1.5-cm-inner-diameter columns. Feed was processed at 1.9 bed volumes (BV) per hour; the flowrate, in terms of contact time with the CST bed, matched the expected flowrate at TSCR. Table S.1 and Figure S.1 summarize the measured AP-105 Cs load performance for each feed condition.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Artificial Intelligence Application to D and D - 20492

As aging facilities across the DOE complex await decommissioning, there is an ongoing need to understand any changes in the structural conditions. Many of these facilities were built over 50 years ago and, in some cases, these facilities have gone beyond the expected operational lifetime. Many facilities have been placed in a state of 'cold and dark,' sitting unused and awaiting decommissioning. Especially challenging are the aging facilities that provide unique operational/production capabilities to support critical DOE missions and cannot be shut down. In any of these scenarios, the structural integrity of these facilities may become compromised as time passes. It is critical that adequate inspections be performed on a continual basis and that the data collected undergoes sufficient analysis to support timely identification of any new or worsening structural issues as well as prompt needed maintenance and repairs to maintain the facilities in a safe condition. In recent days, Artificial Intelligence (AI) [1] and its application to various domains are growing at fast speed. FIU is performing research in this area and exploring the associated technologies to solve nuclear decommissioning problems. Artificial intelligence refers to the capability of a program to autonomously act, react and adapt to the working environment. AI enables the machine to behave like humans and perform the cognitive functions such as 'learning' and 'problem solving'. AI systems gradually moving from traditional approaches (algorithms and expert systems) towards more efficient and advanced technologies (machine learning [1] and deep learning [2] [3]). AI is the study of algorithms and statistical models that is being used by computers to perform specific tasks without using explicit instructions. FIU is working to develop a pilot-scale infrastructure to implement structural health monitoring using AI technologies with focus on machine learning, deep learning. This research is focused on Computer Vision/Image Classification area of AI applications. This can also be expanded to other areas of AI related to Object Recognition and Character Recognition in images. In addition to utilizing existing data sets, FIU will collect and investigate image and video data using FIU test-bed mockups to monitor structural health of the facility. Resulting data will be processed and analyzed using machine learning/deep learning technologies. The proposed pilot system is intended to serve as a starting point to engage the DOE field sites on related data sets and their decision making needs. It is anticipated that proposed machine learning/deep learning technologies can be effectively employed using anomaly detection to solve EM challenges in surveillance and maintenance of the D and D facilities. FIU will work with research stakeholders to identify applications at various sites and other DOE facilities. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Stirred-Reactor Coupon Analysis: An International Round Robin Study

The objective of this task was to determine the precision of the SRCA technique when used to determine the dilute condition corrosion rate. To this end, an interlaboratory round robin study was conducted per the instructions in ASTM Practice E691 to measure the precision with which the SRCA test method can be conducted. Twelve independent labs from eleven different institutions each evaluated four glass compositions in three different conditions. The ASTM procedures recommend at least 6 labs participate in a round robin testing the same 3 materials in the same conditions to determine precision. In this case, 12 labs each performed 12 independent tests. This was only possible thanks to the multi-glass testing capability of the SRCA test. A total of 108 duplicate pairs were used to calculate the repeatability of the tests, with the same glass tested in the same vessel, producing as identical conditions as possible for the replicates. These test results were quite tightly clustered, with a median difference from the average value of the pair of only 2.9%. Based on the calculations outlined in ASTM E177-20 and a measured standard deviation of 4.74%, the intralaboratory repeatability limit (r) was calculated to be within 13.3% of the expected value with 95% confidence level. The reproducibility limit (R) of the test was examined using all 277 data points from the round robin. Because of the differences in dissolution rates due to pH variability and intrinsically for the 12 conditions tested, the reproducibility limits for each condition and overall were calculated from the percent relative residual value for each test. The SRCA test is expected to be reproducible within 64% of the expected value with a 95% confidence level.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Insights into Active Sites and Mechanisms of Benzyl Alcohol Oxidation on Nickel–Iron Oxyhydroxide Electrodes

The electrochemical oxidation of bio-derived molecules has recently garnered interest for its potential in opening electrified synthetic pathways toward value-added products. Herein, we investigate the electrochemical conversion of benzyl alcohol (BA) to benzaldehyde and benzoate on nickel–iron (Fe ~ 7–18%) electrodes as a model system to understand reaction mechanisms and environmental conditions that can transform these molecules. Our results indicate a strong correlation between benzyl alcohol oxidation (BAO) onset potentials and Ni(II/III) redox peak positions, highlighting the potential role that lower oxidation states of nickel, i.e., Ni 3+ , can play in BAO catalysis. Our work on the Ni 2+/3+ system complements mechanisms that involve higher oxidation states of Ni as reported by others. We note that the Ni redox position and thus BAO onset is impacted by Fe incorporation during electrochemistry from unpurified electrolytes, which can resemble standard reactor operating conditions. We perform a systematic computational investigation into BAO and provide density functional theory (DFT) insights into how the redox mechanism has been such a prominent focus of alcohol oxidations. This includes the mode of BA adsorption and the nature of the adsorption site; upon conversion of the Ni 2+ surface to active Ni 3+ via hydroxyl deprotonation, BAO is thermodynamically downhill. Our DFT study also introduces the possibility of a vacancy-driven mechanism, though expected to be less prevalent during catalysis than the redox mechanism for a Ni 3+ surface. Through the systematic investigation of experimental reaction conditions and computational free energy thermodynamics, we have gained valuable insights into BAO reaction mechanisms that inform catalytic activity. Our study opens avenues for further design and development of catalyst active sites for the oxidation of related organic molecules.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Transition from retrograde to prograde drift instabilities in a magnetron microdischarge

Rotating plasma structures, or “spokes,” in magnetized discharges characterized by perpendicular electric and magnetic fields have been seen in a growing number of studies and are believed to be the result of gradient-driven drift instabilities. Under certain conditions, we have shown the spoke’s rotation to be opposite to the E B direction, i.e., retrograde in its expected direction. Recently, we have linked such counter-intuitive rotation to a local inversion of the electric field. Here, we give further experimental evidence for this inversion and attempt to provide an explanation for a relatively distinct transition seen between retrograde and positive (prograde) drift. In the experiments, a partially magnetized plasma forms inside a magnetron device of mm radius operated with argon. Discharge current–voltage measurements are acquired for a range of argon fill pressure and inter-electrode spacing. We find two branches of operation—a low current branch of negative resistance, coinciding with the retrograde spoke rotation, and a higher current branch of positive resistance, coincident with prograde spoke rotation. We postulate that at low discharge currents, high magnetic field confinement leads to a large density gradient, causing more electron transport to the anode than that demanded by the external circuit. At higher currents, anomalous axial electron transport (across the magnetic field lines) becomes dominant, eliminating the conditions for field inversion. Here, the current thresholds for the field inversion are found to be sensitive to the argon pressure and inter-electrode spacing.

42 ENGINEERING↗
DOE OSTI2020

Evaluation of Steam Cycle Upgrades to Improve the Competitiveness of U.S. Coal Power Plants (Final Scientific / Technical Report)

Increasing the competitiveness of the existing pulverized-coal utility fleet in the United States may be achieved by decreasing heat rate, via increases in steam cycle efficiency through upgraded steam temperatures and use of latest technology available in steam turbine and blading design. The average net plant efficiency of the US coal-fired fleet is approximately 33% (HHV). Plant efficiency increases to approximately 41.4% (HHV) at 1,350°F (732°C) steam temperature. However, achieving these Advanced Ultra-Super Critical (AUSC) steam conditions requires the use of advanced high-temperature materials. While there has been a significant amount of DOE-funded materials R&D, most of the related design work has focused on new (greenfield) units, rather than on opportunities to retrofit this advanced technology to the existing utility fleet. If technology, based upon the advanced materials required for AUSC steam conditions, may be applied to the existing fleet, using an economically viable retrofit, a higher capacity factor can be expected as a result of the increased plant competitiveness. The Electric Power Research Institute (EPRI) was awarded a project by the US Department of Energy to examine the technical and economic feasibility of a series of steam cycle upgrades to the two most prevalent types of U.S. coal power plants: 2,400 psig (16.6 MPa) subcritical and 3,500 psig (24.1 MPa) supercritical pulverized coal units. The nine upgrade options that were originally being considered included increasing the main and reheat steam temperatures from 1,000°F (538°C) to 1,100°, 1,200°, and 1,350°F (593°C, 649°C, and 732°C) while holding the steam pressures constant at their original design values, and cases where just the main steam or reheat steam temperatures were increased. The objective was to minimize the modifications required to the existing power plant while still providing a significant improvement in heat rate. The upgrade options assumed that the boiler enclosure envelope remained unchanged from each base case, and that all applicable OEM design guidelines for normal commercial units were imposed. For the highest temperature supercritical case, an option of using a low-pressure molten salt loop to transfer heat from the furnace to the steam was examined. The first major task of the work scope was designed to examine the technical feasibility of various upgrade options, while the subsequent work determined economic viability of the technically feasible upgrade options. Prior to evaluating the effect of these increased temperatures, a “base case” model of a subcritical and supercritical PC boiler was created, which was used for comparative purposes. Upgrade options were evaluated at full-load, part-load and dynamic transient conditions. Once the technical feasibility of each upgrade option was evaluated, the economic value of the heat rate improvement of each feasible option was determined by detailed modeling of unit dispatch in several regional power markets. The dispatch model was used to estimate the amount of revenue from power sales the upgraded unit would receive in comparison to a non-upgraded version of the same power plant. As a parallel task to the dispatch analysis, the capital cost of implementing the upgrades was estimated. The capital cost estimates were then compared to the increased revenue estimated by the dispatch modeling to determine the economic attractiveness of each upgrade option. Several upgrade options were determined to be technically feasible. The net present value (NPV) of the costs for steam cycle upgrades considered in this study ranged from approximately $\$$111 to $\$$130 million. The economic modeling results show that the unit dispatch changes resulting from steam cycle upgrades are relatively small, due largely to heat rate (and operating cost) changes being relatively small. Additionally, the cost of each upgrade exceeds the net revenue increases associated with the upgrade case. Note that the breakeven values are higher for subcritical retrofits, but the capital costs for the subcritical upgrades are also slightly higher. In typical new pulverized coal plants, fuel accounts for approximately 25% of the cost of electricity (COE), while capital costs represent around 50% of the COE. Therefore, in order to improve the heat rate by 4% one can only afford to increase the capital cost by 2%, at the same cost of electricity. The conclusion of this study is that without a cost for emitting CO 2 , it will be difficult to pay for significant efficiency improvements on plants firing low cost coals.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2025

Tests of a High Temperature Sample Conditioner for the Waste Treatment Plant LV-S2, LV S3, HV S3A and HV-S3B Exhaust Systems

Tests were performed to evaluate a sample conditioning unit for stack monitoring at Hanford Tank Waste Treatment and Immobilization Plant (WTP) exhaust stacks with elevated air temperatures. The LV-S2, LV-S3, HV-S3A and HV-S3B exhaust stacks are expected to have elevated air temperature and dew point. At these emission points, exhaust temperatures are too high to deliver the air sample directly to the required stack monitoring equipment. As a result, a sample conditioning system is considered to cool and dry the air prior to its delivery to the stack monitoring system. The method proposed for the sample conditioning is a dilution system that will introduce cooler, dry air to the air sample stream. This method of sample conditioning is meant to reduce the sample temperature while avoiding condensation of moisture in the sample stream. An additional constraint is that the ANSI/HPS N13.1-1999 standard states that at least 50% of the 10 µm aerodynamic diameter (AD) particles present in the stack free stream must be delivered to the sample collector. In other words, depositional loss of particles should be limited to 50% in the sampling, transport, and conditioning systems. Based on estimates of particle penetration through the LV-S3 sampling system, the diluter should perform with about 80% penetration or better to ensure that the total sampling system passes the 50% or greater penetration criterion.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2026

Effect of thermal treatments on electrochemical behavior of binder jetted 17-4 PH stainless steel

Binder jetted 17–4 PH stainless steel was post-processed to relate heat treatment, microstructure, and corrosion in 3.5 wt% NaCl. Specimens were sintered at 1380 or 1400 °C, solution-annealed at 1055 °C for 1 h, and aged at 482 °C for 1 h. Here, as-sintered parts showed α′-martensitic matrix with a δ-ferrite network and Cu-rich precipitates in ferrite; inclusions (MnS, NbC) promoted localized attack. solutionizing redistributed elements and reduced ferrite, while aging generated coherent Cu nano-precipitates. Corrosion resistance was highly sensitive to post-processing in which aged specimens exhibited the lowest corrosion current density and formed a thicker, stable Cr 2 O 3 -rich passive film, whereas sintered specimens degraded most. Pitting potential depended on sintering temperature and microstructure, with 1400 °C sintering yielding more positive pitting potentials and the best overall performance after aging. Although the 1400-solutionized condition showed a relatively noble pitting response versus 1380-solutionized, it displayed unstable corrosion kinetics attributed to an imperfect passive film linked to higher NbC density. XPS depth profiles corroborated these trends, showing thicker, more continuous Cr 2 O 3 in aged states and discontinuous/thinning oxides in less resistant conditions. Practically, high-temperature sintering (∼1400 °C) followed by solutionizing and aging is recommended, with further gains expected from reducing NbC/MnS populations and porosity via powder and process control.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Spatiotemporal Variability in Transport and Reactive Processes Across a First- to Fifth-Order Fluvial Network

Fluvial networks integrate and transport constituents from terrestrial and aquatic ecosystems. To date, most research on water quality dynamics has focused on process understanding at individual streams and, as a result, there is a lack of studies analyzing how small-scale, physical and biogeochemical drivers scale across fluvial networks. We performed tracer tests in five stream orders of the Jemez River continuum in New Mexico, USA, to quantify reach-scale hyporheic exchange during two different seasonal periods to address: how do hyporheic zone contributions to riverine processing change with space and time? And does the spatiotemporal variability of hyporheic exchange scale across fluvial networks? Combining conservative (i.e., bromide) and reactive (i.e., resazurin) tracer analyses with solute transport modeling, we found a dominance of reaction-limited transport conditions in space (for all stream orders) and time (two contrasting flow regimes). Moreover, we found a trend toward more reaction-limited conditions with increasing discharge across all stream orders. While our studied fluvial network did not consistently follow the expectations of decreasing hyporheic exchange contributions with increasing stream order, as it has been previously suggested from modeling studies, we found that processing rate coefficients and Damköhler numbers consistently decreased along the continuum with increasing discharge. Our findings suggest that knowledge transferability of hyporheic zone processing along fluvial networks may be possible if the scaling patterns that we found hold true in other catchments. Thus, more research on scaling patterns along fluvial networks is highly needed.

Gootman, Kaylyn S.↗
DOE OSTI2025

Magnetohydrodynamic simulations preliminarily predict the habitability and radio emission of TRAPPIST-1e

TRAPPIST-1e, an Earth-sized exoplanet in the habitable zone of the nearby M dwarf TRAPPIST-1, may experience magnetospheric responses that vary with stellar space weather, which could potentially influence both its habitability and radio emissions. Our objective is to investigate how different Earth-like magnetospheric configurations of TRAPPIST-1e – specifically variations in dipolar magnetic field strength and axial tilt – respond to diverse stellar space weather conditions, including events analogous to coronal mass ejections (CMEs), and to assess their implications for potential habitability and expected radio emissions. We conducted 3D magnetohydrodynamic simulations of the TRAPPIST-1e system using the PLUTO code in spherical coordinates. The planetary magnetic field was modelled as dipolar, with equatorial strengths from Earth-like to several times stronger. The dipole axis spans a representative range of axial tilts. We investigate four stellar wind environments, from sub-Alfvénic flow to CME-like disturbances. Planetary shielding was quantified based on the magnetopause standoff distance, and radio powers were estimated via empirical scaling laws. Our simulations show that both shielding and radio power depend strongly on the magnetic configuration. Stronger fields increase protection, while larger tilts reduce it. Radio power increases with both field strength and tilt across all wind regimes. An Earth-like magnetic field can provide effective shielding even under intense CMEs, whereas high tilts require stronger fields. Predicted radio powers reach ~10 20 erg s −1 during CMEs, making bursts from close-in, magnetised planets more detectable. However, for TRAPPIST-1e, the maximum cyclotron frequency lies below the Earth’s ionospheric cutoff (~10 MHz), making ground-based detection currently infeasible.

Sun: magnetic fields↗
DOE OSTI2023

Experimental demonstration of >20 kJ laser energy coupling in 1-cm hydrocarbon-filled gas pipe targets via inverse Bremsstrahlung absorption with applications to MagLIF

Laser propagation experiments using four beams of the National Ignition Facility to deliver up to 35 kJ of laser energy at 351 nm laser wavelength to heat magnetized liner inertial fusion-scale (1 cm-long), hydrocarbon-filled gas pipe targets to ~keV electron temperatures have demonstrated energy coupling >20 kJ with essentially no backscatter in 15% critical electron density gas fills with 0–19 T applied axial magnetic fields. The energy coupling is also investigated for an electron density of 11.5% critical and for applied field strengths up to 24 T at both densities. This spans a range of Hall parameters 0 < ω ce τ ei ≲ 2, where a Hall parameter of 0.5 is expected to reduce electron thermal conduction across the field lines by a factor of 4–5 for the conditions of these experiments. At sufficiently high applied field strength (and therefore Hall parameter), the measured laser propagation speed through the targets increases in the measurements, consistent with reduced perpendicular electron thermal transport; this reduces the coupled energy to the target once the laser burns through the gas pipe. In conclusion, the results compare well with a 1D analytic propagation model for inverse Bremsstrahlung absorption.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Generalized kinetic equation for tokamak plasma equilibrium distribution function

A generalised kinetic equation for the equilibrium distribution function in a finite beta, arbitrary tokamak plasma is derived. The equation is correct to second order in ρ/L (ρ is the particle Larmor radius and L is the system size). Resolving finite Larmor radius length scales with no restriction on the ratio of poloidal to total equilibrium magnetic field, B $\vartheta$ /B, it generalises the drift kinetic theory of [Hazeltine Phys. Plasmas 15 (1973) 77] to the limit of B $\vartheta$ /B ~ 1 (e.g. to ensure validity for spherical tokamaks). Two cases are considered. The first provides the equilibrium distribution function, consistent with the generalised gyrokinetic formalism of [Dudkovskaia et al. Plasma Phys. Control. Fusion 65 (2023) 045010], derived specifically to capture neoclassical equilibrium currents in gyrokinetic stability analyses in strong gradient regions. The second assumes short length scales in the direction perpendicular to the magnetic field, which can occur as a result of small coherent magnetic structures in the plasma, such as neoclassical tearing mode magnetic islands close to threshold. This then extends the drift island equations of [Dudkovskaia et al. Nucl. Fusion 63 (2023) 016020] for the plasma response to magnetic islands to a spherical tokamak plasma configuration. In conclusion, resolving ρ ~ ρ $\vartheta$ (or B $\vartheta$ ~ B), where ρ $\vartheta$ is the particle poloidal Larmor radius, is also expected to influence calculations of the magnetic island propagation frequency and the associated contributions to the island onset conditions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Extending the low-recycling, flat temperature profile regime in the lithium tokamak experiment-β (LTX-β) with ohmic and neutral beam heating

Abstract Recent experiments in the lithium tokamak experiment- β (LTX- β ) have extended the duration, performance, operating conditions, and diagnosis of the flat-temperature profile, low-recycling regime first observed in LTX. As expected, Li retains hydrogen and suppresses edge neutral cooling, allowing increased edge electron temperature, roughly equal to the core T e . Flat temperature profiles had been obtained transiently in LTX, as the plasma density decayed following the cessation of edge gas puffing. Careful control over the fueling in LTX- β has now been shown to sustain the flat T e profile and hot edge unique to the low-recycling regime for multiple confinement times in high performance discharges with decaying or steady density. With low density, the flat T e profile is also seen to extend into the scrape-off layer. Neutral beam heating is observed in target discharges with relatively flat electron temperature profiles ( T edge ∼ T core /2), though beam heating is stronger in discharges with higher fueling, higher density, and depressed edge T e . Beam heating produces additional peaking of the T e profile, without degradation of the energy confinement time. Neutral beam heating of target discharges with relatively flat electron temperature profiles similarly results in broad beam heated temperature profiles. Energy confinement in LTX- β generally compares favorably to ohmic and H-mode scalings, frequently exceeding them by factors of 2–4. New and improved diagnostics in LTX- β enable better characterization of this unique regime, including measurements of ion temperature and high field side Thomson scattering profiles. As an initial step toward characterizing turbulence with no T e gradient and roughly equal density and pressure gradient, core fluctuation spectra have been measured in peaked T e discharges using far-forward scattering and fluctuation reflectometry.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Modelling and assessing the near-wake representation and turbulence behaviour of control-oriented wake models

Due to the interaction between the wake of an upstream turbine on a downstream turbine, power losses and increased fatigue loads occur. By yawing the upstream turbine with regard to the wind direction, one can potentially reduce the power losses of the downstream turbine and reduce the fatigue loads. The evolution of the wake depends on the pressure gradient within the near-wake region and the turbulent kinetic energy and must be incorporated in existing wake steering algorithms to provide an accurate estimation of the wake flow. This paper will show a first approach to implement a near-wake model and a turbulence model in the curled wake model within the controls-oriented framework FLORIS. The near-wake model is based on an analytical expression of the velocity profile to model the pressure gradient. Furthermore, two turbulence models are incorporated within the curled wake model based on a Gaussian-distribution and a mixing length formulation. The adapted curled wake model is then assessed with the measurement data acquired in the wind tunnel at ForWind – University of Oldenburg. The evaluation of the models show good agreement for the velocity deficit and representation of the near-wake region. Furthermore, the turbulent kinetic energy behaved as expected in comparison to other work, showing a ring of high turbulent kinetic energy at non-yawed condition which is deflected to a curled shape at large yaw angles with the turbulence model based on a mixing length formulation.

FLORIS↗
DOE OSTI2025

Projected increases in tropical cyclone-induced U.S. electric power outage risk

Abstract While power outages caused by tropical cyclones (TCs) already pose a great threat to coastal communities, how—and why—these risks will change in a warming climate is poorly understood. To address this need, we develop a robust machine learning model to capture TC-induced power outage risk. When applied to 900 000 synthetic TCs downscaled from simulated historical and future climate conditions under a strong warming scenario, we find outage risk in the United States and Puerto Rico is expected to increase broadly by the end of the century, with some states seeing increases of 60% and higher. Further, we discover that rising rainfall rates will play an increasingly important role in TC-induced power outage risk as the climate changes, explaining more than 50% of the projected change in risk in some regions. These insights are important for guiding decision-makers in their future outage risk investment and mitigation plans.

Grid Resilience↗
DOE OSTI2021

Soot Predictions with a Laminar Flamelet Combustion Model in SIERRA/Fuego on a Coflow Scenario

This report describes an assessment of flamelet based soot models in a laminar ethylene coflow flame with a good selection of measurements suitable for model validation. Overall flow field and temperature predictions were in good agreement with available measurements. Soot profiles were in good agreement within the flame except for near the centerline where imperfections with the acetylene-based soot-production model are expected to be greatest. The model was challenged to predict the transition between non-sooting and sooting conditions with non-negligible soot emissions predicted even down to small flow rates or flame sizes. This suggests some possible deficiency in the soot oxidation models that might alter the amount of smoke emissions from flames, though this study cannot quantify the magnitude of the effect for large fires.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗