Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “conditional expectations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
NASA NTRS1931

Estimated Effect of Ring Cowl on the Climb and Ceiling of an Airplane, Special Report

Although the application of a ring cowl to an airplane with an air-cooled engine increases the maximum L/D and the high speed to an appreciable extent, the performance in climb and ceiling is not increased as much as one would expect without analyzing the conditions. When a ring cowl is installed on an airplane, the propeller is set at a higher pitch to allow the engine to turn its rated r.p.m. at the increased high speed. V/nD is increased and the propeller efficiency at high speed is increased slightly. The ratio of r.p.m. at climbing speed, V(sub c) , to the r.p.m. at maximum speed, V (sub m) is dependent upon the ratio of V(sub c) to V(sub m). The increase in V(sub c) for all airplane with ring cowl i s not as great as the increase in V(sub m), so that the ratio V(sub c)/V(sub m) is less than for the airplane without ring. Consequently the r.p.m. and full throttle thrust power available are less at V(sub c) for the airplane with ring cowl and in spite of the increase in L/D due to the installation of the ring, the excess thrust power available for climbing is not appreciably changed. The same method of reasoning accounts for the small increase in absolute ceiling in spite of a large increase in L/D maximum.

Louden, F. A.↗
NASA NTRS2006

Predicting Tail Buffet Loads of a Fighter Airplane

Buffet loads on aft aerodynamic surfaces pose a recurring problem on most twin-tailed fighter airplanes: During maneuvers at high angles of attack, vortices emanating from various surfaces on the forward parts of such an airplane (engine inlets, wings, or other fuselage appendages) often burst, immersing the tails in their wakes. Although these vortices increase lift, the frequency contents of the burst vortices become so low as to cause the aft surfaces to vibrate destructively. Now, there exists a new analysis capability for predicting buffet loads during the earliest design phase of a fighter-aircraft program. In effect, buffet pressures are applied to mathematical models in the framework of a finite-element code, complete with aeroelastic properties and working knowledge of the spatiality of the buffet pressures for all flight conditions. The results of analysis performed by use of this capability illustrate those vibratory modes of a tail fin that are most likely to be affected by buffet loads. Hence, the results help in identifying the flight conditions during which to expect problems. Using this capability, an aircraft designer can make adjustments to the airframe and possibly the aerodynamics, leading to a more robust design.

Moses, Robert W.↗
NASA NTRS2010

Testing a Regenerative Carbon Dioxide and Moisture Removal Technology

The National Aeronautics and Space Administration supported the development of a new vacuum-desorbed regenerative carbon dioxide and humidity control technology for use in short duration human spacecraft. The technology was baselined for use in the Orion Crew Exploration Vehicle s Environmental Control and Life Support System (ECLSS). Termed the Carbon Dioxide And Moisture Removal Amine Swing-bed (CAMRAS), the unit was developed by Hamilton Sundstrand and has undergone extensive testing at Johnson Space Center. The tests were performed to evaluate performance characteristics under range of operating conditions and human loads expected in future spacecraft applications, as part of maturation to increase its readiness for flight. Early tests, conducted at nominal atmospheric pressure, used human metabolic simulators to generate loads, with later tests making us of human test subjects. During these tests many different test cases were performed, involving from 1 to 6 test subjects, with different activity profiles (sleep, nominal and exercise). These tests were conducted within the airlock portion of a human rated test chamber sized to simulate the Orion cabin free air volume. More recently, a test was completed that integrated the CAMRAS with a simulated suit loop using prototype umbilicals and was conducted at reduced atmospheric pressure and elevated oxygen levels. This paper will describe the facilities and procedures used to conduct these and future tests, and provide a summary of findings.

Barta, Daniel J.↗
NASA NTRS2011

Supersonic/Hypersonic Correlations for In-Cavity Transition and Heating Augmentation

Laminar-entry cavity heating data with a non-laminar boundary layer exit flow have been retrieved from the database developed at Mach 6 and 10 in air on large flat plate models for the Space Shuttle Return-To-Flight Program. Building on previously published fully laminar and fully turbulent analysis methods, new descriptive correlations of the in-cavity floor-averaged heating and endwall maximum heating have been developed for transitional-to-turbulent exit flow. These new local-cavity correlations provide the expected flow and geometry conditions for transition onset; they provide the incremental heating augmentation induced by transitional flow; and, they provide the transitional-to-turbulent exit cavity length. Furthermore, they provide an upper application limit for the previously developed fully-laminar heating correlations. An example is provided that demonstrates simplicity of application. Heating augmentation factors of 12 and 3 above the fully laminar values are shown to exist on the cavity floor and endwall, respectively, if the flow exits in fully tripped-to-turbulent boundary layer state. Cavity floor heating data in geometries installed on the windward surface of 0.075-scale Shuttle wind tunnel models have also been retrieved from the boundary layer transition database developed for the Return-To-Flight Program. These data were independently acquired at Mach 6 and Mach 10 in air, and at Mach 6 in CF4. The correlation parameters for the floor-averaged heating have been developed and they offer an exceptionally positive comparison to previously developed laminar-cavity heating correlations. Non-laminar increments have been extracted from the Shuttle data and they fall on the newly developed transitional in-cavity correlations, and they are bounded by the 95% correlation prediction limits. Because the ratio of specific heats changes along the re-entry trajectory, turning angle into a cavity and boundary layer flow properties may be affected, raising concerns regarding the application validity of the heating augmentation predictions.

Everhart, Joel L.↗
NASA NTRS2014

Large-Scale Spacecraft Fire Safety Tests

An international collaborative program is underway to address open issues in spacecraft fire safety. Because of limited access to long-term low-gravity conditions and the small volume generally allotted for these experiments, there have been relatively few experiments that directly study spacecraft fire safety under low-gravity conditions. Furthermore, none of these experiments have studied sample sizes and environment conditions typical of those expected in a spacecraft fire. The major constraint has been the size of the sample, with prior experiments limited to samples of the order of 10 cm in length and width or smaller. This lack of experimental data forces spacecraft designers to base their designs and safety precautions on 1-g understanding of flame spread, fire detection, and suppression. However, low-gravity combustion research has demonstrated substantial differences in flame behavior in low-gravity. This, combined with the differences caused by the confined spacecraft environment, necessitates practical scale spacecraft fire safety research to mitigate risks for future space missions. To address this issue, a large-scale spacecraft fire experiment is under development by NASA and an international team of investigators. This poster presents the objectives, status, and concept of this collaborative international project (Saffire). The project plan is to conduct fire safety experiments on three sequential flights of an unmanned ISS re-supply spacecraft (the Orbital Cygnus vehicle) after they have completed their delivery of cargo to the ISS and have begun their return journeys to earth. On two flights (Saffire-1 and Saffire-3), the experiment will consist of a flame spread test involving a meter-scale sample ignited in the pressurized volume of the spacecraft and allowed to burn to completion while measurements are made. On one of the flights (Saffire-2), 9 smaller (5 x 30 cm) samples will be tested to evaluate NASAs material flammability screening tests. The first flight (Saffire-1) is scheduled for July 2015 with the other two following at six-month intervals. A computer modeling effort will complement the experimental effort. Although the experiment will need to meet rigorous safety requirements to ensure the carrier vehicle does not sustain damage, the absence of a crew removes the need for strict containment of combustion products. This will facilitate the first examination of fire behavior on a scale that is relevant to spacecraft fire safety and will provide unique data for fire model validation.

Combustion↗
NASA NTRS2014

Development of the RANCOR Rotary-Percussive Coring System for Mars Sample Return

A RANCOR drill was designed to fit a Mars Exploration Rover (MER) class vehicle. The low mass of 3 kg was achieved by using the same actuator for three functions: rotation, percussions, and core break-off. Initial testing of the drill exposed an unexpected behavior of an off-the-shelf sprag clutch used to couple and decouple rotary-percussive function from the core break off function. Failure of the sprag was due to the vibration induced during percussive drilling. The sprag clutch would back drive in conditions where it was expected to hold position. Although this did not affect the performance of the drill, it nevertheless reduced the quality of the cores produced. Ultimately, the sprag clutch was replaced with a custom ratchet system that allowed for some angular displacement without advancing in either direction. Replacing the sprag with the ratchet improved the collected core quality. Also, premature failure of a 300-series stainless steel percussion spring was observed. The 300-series percussion spring was ultimately replaced with a music wire spring based on performances of previously designed rotary-percussive drill systems.

Paulsen, Gale↗
NASA NTRS2016

Boundary Layer Transition During the Orion Exploration Flight Test 1 (EFT-1)

Boundary layer transition was observed in the thermocouple data on the windside backshell of the Orion reentry capsule. Sensors along the windside centerline, as well as off-centerline, indicated transition late in the flight at approximately Mach 4 conditions. Transition progressed as expected, beginning at the sensors closest to the forward bay cover (FBC) and moving towards the heatshield. Sensors placed in off-centerline locations did not follow streamlines, so the progression of transition observed in these sensors is less intuitive. Future analysis will include comparisons to pre-flight predictions and expected transitional behavior will be investigated. Sensors located within the centerline and off-centerline launch abort system (LAS) attach well cavities on the FBC also showed indications of boundary layer transition. The transition within the centerline cavity was observed in the temperature traces prior to transition onset on the sensors upstream of the cavity. Transition behavior within the off centerline LAS attach well cavity will also be investigated. Heatshield thermocouples were placed within Avcoat plugs to attempt to capture transitional behavior as well as better understand the aerothermal environments. Thermocouples were placed in stacks of two or five vertically within the plugs, but the temperature data obtained at the sensors closest to the surface did not immediately indicate transitional behavior. Efforts to use the in depth thermocouple temperatures to reconstruct the surface heat flux are ongoing and any results showing the onset of boundary layer transition obtained from those reconstructions will also be included in this paper. Transition on additional features of interest, including compression pad ramps, will be included if it becomes available.

Kirk, Lindsay C.↗
NASA NTRS2014

Monolayer Graphene Bolometer as a Sensitive Far-IR Detector

In this paper we give a detailed analysis of the expected sensitivity and operating conditions in the power detection mode of a hot-electron bolometer (HEB) made from a few micro m(sup 2) of monolayer graphene (MLG) flake which can be embedded into either a planar antenna or waveguide circuit via NbN (or NbTiN) superconducting contacts with critical temperature approx. 14 K. Recent data on the strength of the electron-phonon coupling are used in the present analysis and the contribution of the readout noise to the Noise Equivalent Power (NEP) is explicitly computed. The readout scheme utilizes Johnson Noise Thermometry (JNT) allowing for Frequency-Domain Multiplexing (FDM) using narrowband filter coupling of the HEBs. In general, the filter bandwidth and the summing amplifier noise have a significant effect on the overall system sensitivity.

noise thermometry↗
NASA NTRS2018

Instability Wave–Streak Interactions in a High Mach Number Boundary Layer at Flight Conditions

The interaction of stationary streaks undergoing nonmodal growth with modally unstable instability waves in a hypersonic boundary-layer flow is studied using numerical computations. The geometry and flow conditions are selected to match a relevant trajectory location from the ascent phase of the HIFiRE-1 flight experiment; namely, a 7 degree half-angle, circular cone with 2.5 mm nose radius, freestream Mach number equal to 5.30, unit Reynolds number equal to 13.42 m -1 , and wall-to-adiabatic temperature ratio of approximately 0.35 over most of the vehicle. This paper investigates the nonlinear evolution of initially linear optimal disturbances that evolve into finite-amplitude streaks, followed by an analysis of the modal instability characteristics of the perturbed, streaky boundary-layer flow. The investigation is performed with stationary direct numerical simulations (DNS) and plane-marching parabolized stability equations (PSE), in conjunction with partial-differential-equation-based planar eigenvalue analysis. The overall effect of streaks is to reduce the peak amplification factors of instability waves, indicating a possible downstream shift in the onset of laminar-turbulent transition. The present study confirms previous findings that the mean flow distortion of the nonlinear streak perturbation reduces the amplification rates of the Mack-mode instability. More importantly, however, the present results demonstrate that the spanwise varying component of the streak can produce a larger effect on the Mack-mode amplification. The study with selected azimuthal wavenumbers for the stationary streaks reveals that a wavenumber of approximately 1.4 times larger than the optimal wavenumber is more effective in stabilizing the planar Mack-mode instabilities. In the absence of unstable first-mode waves for the present cold-wall condition, transition onset is expected to be delayed until the peak streak amplitude increases to nearly 35 percent of the freestream velocity, when intrinsic instabilities of the boundary-layer streaks begin to dominate the transition process. For streak amplitudes below that limit a significant net stabilization is achieved, yielding a potential transition delay that can exceed 100 percent of the length of the laminar region in the uncontrolled case.

Boundary layer stability↗
NASA NTRS2018

Broadband Inlet Liner Design for the DGEN Aero-Propulsion Research Turbofan

The utilization of advanced fan designs (including higher bypass ratios) and shorter engine nacelles has highlighted a need for increased fan noise reduction over a broad frequency range. With these observations in mind, an acoustic liner optimization process has been developed to achieve improved broadband liner designs. A series of advanced liner design studies at increasing technology readiness levels has been conducted as the overall optimization methodology has been enhanced. In this work, further validation was pursued through the fabrication and testing of two liner designs for the NASA Glenn DGEN Aero-propulsion Research Turbofan. Specifically, single and three layer liners were designed, fabricated, and tested. Analysis of the predicted attenuation results showed them to generally match expected trends for the conditions considered. The effects of source distribution on predicted directivity were also illustrated through the flexibility of a statistical source model. As part of the analysis, the overall design and evaluation capability was extended such that external observer locations may be included in the optimization process. This enhancement will provide a much wider design space for the development of advanced broadband liners. These preliminary results provide further confidence in the design tools and enhancements made to the overall liner design process.

Nark, Douglas M.↗
NASA NTRS2020

Microstructure and Hardness of 57Ni –40Ti –3Hf (wt.%)

Ni-rich NiTiHf (57 wt.% Ni – 40 wt.% Ti – 3 wt.% Hf) is an intermetallic material that is superelastic, corrosion resistant and hardenable through relatively simple heat treatment procedures. The composition, microstructure and hardness of two separate lots of Ni-rich NiTiHf were investigated. The measured compositions for both lots were nominal, with total impurities in each of less than 0.01 wt%. The average grain sizes were 28.0µm and 26.4µm for the two lots. In its annealed condition (1,050°C × 48h/furnace cool to room temperature), the microstructure consisted of a B2 (cubic) NiTiHf parent phase with abundant Ni4Ti3 precipitates and a few TiC inclusions. The grain boundaries were decorated with HfO2 particles and metastable Ni3Ti2 precipitates that were cubic in structure. The average hardness varied from approximately 470HV to 490HV for the two lots. The hardened (annealed then 900°C × 2h/water quench to room temperature) microstructure consisted of a B2 NiTiHf parent phase with no precipitates, HfO2 decorating the grain boundaries and some TiC inclusions. The average hardness in this heat treatment condition was approximately 580HV for both lots. The aged (hardened then 400°C × 30min/water quench to room temperature) microstructure consisted of a B2 NiTiHf parent phase containing a high density of very fine Ni4Ti3 precipitate phase, HfO2 decorating the grain boundaries and some TiC inclusions. For each lot, the average hardness decreased slightly after aging as compared to the hardened heat treatment condition. This report is expected to serve as a reference for a forthcoming Materials Specification for the use of Ni-rich NiTiHf in flight hardware.

intermetallics, compositional analysis, Vickers ha↗
NASA NTRSDate not supplied

Explicit Discontinuous Galerkin Methods for Conservation Laws

The two explicit DG methods in this study are based on a ‘predictor-corrector’ formulation, the first introduced by Lörcher, Gassner, and Munz (2007, 2008) called space–time expansion discontinuous Galerkin or STE-DG scheme, and the second, introduced independently by the author (Huynh 2006, 2013) called the upwind moment scheme. The predictor step of the two methods is essentially identical using a Cauchy-Kovalevsky (CK) procedure, which involves no interaction of the data among neighboring cells. The corrector step also shares the same space-time integration formulation and is where interaction of the data among neighboring cells takes place; the difference, however, is in how the resulting space-time volume integral is estimated. As a consequence of the different estimates, for the case of advection in one spatial dimension (1D), the moment scheme has a CFL (Courant-Friedrichs-Lewy) condition of 1 for all p and is accurate to order 2p+1, i.e., it possesses the super accuracy property, whereas the STE-DG method has a more restrictive CFL condition and is accurate to the expected order of p+1. For 1D advection, compared with the CFL conditions of 1/(2p+1) of standard RK-DG (Runge-Kutta) scheme where space and time discretization are of the same order, the moment scheme allows a significantly larger time step size. It also turns out that the scheme yields a result identical to Van Leer’s scheme III (1977), which amounts to shifting the data a distance of advection corresponding to the time step and projecting the result onto the space of polynomial solutions. Contrary to Van Leer’s approach, however, the space-time ‘predictor-corrector’ formulation facilitates extensions to the case of systems of equations. Concerning 2D extensions, in the case of advection, when the flow is along the diagonal direction, the CFL conditions for the moment schemes become restrictive as will be shown by Fourier (Von Neumann) stability and accuracy analyses. Since the moment scheme employs the right Radau points as collocation points in time, the method is closely related to the implicit Radau IIA scheme, which is stable for any time step size. The role of Radau IIA in relieving stability restriction for these explicit DG schemes remains to be explored

Discontinuous Galerkin↗
NASA NTRSDate not supplied

Verification Test Suite for Spalart-Allmaras QCR2000 Turbulence Model

The paper presents three benchmark cases for verification of Reynolds-averaged Navier-Stokes solvers. The verification studies focus on a one-equation Spalart-Allmaras model, SA-[neg]-QCR2000, that uses a version of quadratic constitutive relations.The benchmark cases are a two-dimensional subsonic flow around a Joukowski airfoil, a three-dimensional supersonic flow through a square duct, and a three-dimensional flow over a wing-fuselage configuration. The turbulence-model formulation, geometry, flow conditions, grids, and the expected output are described in detail. Reference solutions computed by several established codes are shown

Computational Aerodynamics↗
NASA NTRSDate not supplied

Probabalistic Risk Analysis and Thermal Margin Process for an Inflatable Aeroshell

Uncertainties always exist in atmospheric entry aeroheating environments and the thermal response of thermal protection system (TPS) material. These uncertainties are mitigated in the design by ap-plying margin and factors of safety to the TPS. Entry vehicle TPS is often conservatively over-sized for the heat loads that are experienced along the entry trajectory by stacking worst-case scenarios together. Additionally, the current TPS design and margin process used by NASA offers very little insight into the risk of over-temperature during flight and the reliability of the heat shield performance [1,3]. A probabilistic margin process can be used to calculate the amount of TPS margin necessary to survive a given entry heat load at a specified level of risk [2,3,4]. The vehicle’s initial entry state (entry velocity, flight path angle, and entry mass) determines the expected atmospheric entry environmental conditions and resulting heat load that the entry vehicle will experience. If there is flexibility in the entry state, then this process can be used to select an appropriate combination of entry state parameters and TPS size to target a desired reentry reliability. This probabilistic margin process allows engineers to make informed aeroshell design, entry-trajectory design, and TPS performance risk trades while preventing excessive TPS margin from being applied. The probabilistic TPS margin process has been performed to determine TPS thickness and entry heating constraints given an acceptable risk level for the Low Earth Orbit Flight Experiment of an Inflatable Decelerator (LOFTID) flight project. The process is used in a manner to size the entry heat load for a given flexible TPS (FTPS) thickness so that it meets project reliability standards while allowing the FTPS and the underlying inflatable structure (IS) to be pushed to adequately high temperatures. Since the LOFTID project is an experimental flight demonstration, it is de-sired to drive the FTPS and IS to temperatures that cover a large range of their thermal response models’ applicability. This will allow the thermal response models to be better improved and validated post-flight using LOFTID’s extensive instrumentation embedded within the aeroshell. The presentation demonstrates how uncertainty analysis is carried out using an end-to-end Monte Carlo process where three separate Monte Carlo simulations are run in sequence. The first Monte Carlo simulation operates on the entry trajectory model to generate trajectory parameter dispersions that are fed into the second Monte Carlo simulation. The second Monte Carlo simulation operates on the aerothermodynamics model to generate aeroheating parameter dispersions that are fed into the third Monte Carlo simulation. The third Monte Carlo simulation operates on the FTPS material thermal response model to generate the final FTPS/IS thermal response dispersions. The end-to-end Monte Carlo simulation propagates the uncertainties of each model into the next to quantify the resulting uncertainty of the FTPS/IS thermal response. The fractional contributions of the uncertain parameters in the trajectory, aerothermal, and thermal response models to the variance in the FTPS/IS thermal response is determined as a byproduct of the Monte Carlo analysis. The structural uncertainty of the FTPS thermal response model is evaluated by flight relevant ground testing and model error analysis using test measurements. This probabilistic TPS margin process had never been applied to an entry vehicle and it is one of the LOFTID project’s goals to demonstrate its merits.

Steven A. Tobin↗
NASA NTRS2023

Highly Restricted Near‐Surface Permafrost Extent During the Mid-Pliocene Warm Period

To better understand how near‐surface permafrost may respond to future warming, we explore the equilibrium spatial extent of near‐surface permafrost during the mid-Pliocene warm period (mPWP), which shares characteristics of the projected future climate. Our simulations, which are constrained by proxy records, suggest highly restricted near‐surface permafrost extent during the mPWP, akin to future large-scale permafrost degradation projections of our model for the end of this century. Our study indicates dramatically smaller-than-present near‐surface permafrost extent in the geological past under climate conditions analogous to those expected if global warming continues unabated. This absence in permafrost will come with critical implications for the global carbon cycle, human livelihoods and infrastructures, and surface and subsurface hydrology.

near‐surface permafrost↗
NASA NTRS2024

Quantifying Risk to Improve Medical System Design for Long Duration Artemis Missions: A Demonstration of NASA's IMPACT Tradespace Analysis Tool

BACKGROUND NASA’s human exploration spaceflight missions to the Moon and Mars present unprecedented challenges for in-mission medical care. A greater distance from Earth will mean increased mission durations, communication delays, limited to no resupply opportunities, and constraints on the evacuation of ill or injured crew. Mass, volume, and power will be limited while higher demands will be placed on the crews to manage medical events. NASA’s Moon to Mars exploration strategy outlines increasingly complex Artemis missions both in terms of duration and operations. In these more challenging deep space missions, it is important to quantitatively estimate the human system risk attributable to medical conditions and use these estimates to advance medical system design. METHODS IMPACT (Informing Mission Planning via Analysis of Complex Tradespaces) is a probabilistic risk assessment (PRA) and tradespace analysis tool developed by NASA to advance exploration mission medical system design. IMPACT v1.0 includes a novel evidence library baselined to exploration environments; an expanded list of 119 medical conditions; a large increase in the number of medical resources and the flexibility of their use; and the ability for rapid and iterative analysis. Medical system risk estimates include loss of crew life, consideration of the need for return to definitive care (medical evacuation), and an estimate of crew time affected due to medical conditions. A notional long duration lunar orbit and lunar surface design reference mission (DRM) was chosen with a 4-astronaut crew to mimic a foundational exploration Artemis mission. The DRM profile includes outbound transit on Orion, Gateway space station rendezvous in lunar orbit, 6 months on the Lunar surface with extravehicular activity (EVA), return rendezvous with Gateway, and transit back to Earth. RESULTS/DISCUSSION: Overall, IMPACT successfully quantified medical risk and derived an optimal medical system to support crew on a long duration lunar mission. In this DRM, the calculated loss of crew life from a medical event was 0.008 events per mission, risk of potential need for evacuation was 0.30 events per mission, and cumulative crew time affected by medical conditions was 103 days. The medical conditions that most contributed to medical risk were decompression sickness, trauma, and respiratory failure. The conditions that had the largest effects on crew performance included musculoskeletal injuries and lunar dust exposure. The IMPACT-generated medical system included resources that target the most common and highest risk conditions and performed as expected. This demonstrates the value of the IMPACT tool in medical system design for human exploration spaceflight missions.

Arian Anderson↗
DOE OSTI2024

Integrated modeling for assessing climate change impacts on water resources and hydropower potential in the Himalayas

Regional hydroclimatic variability and change can affect water resources and hydropower generation. It is essential to assess hydropower potential under current and future climatic conditions to inform the design and operation of hydropower infrastructures. Here, we employ an integrated modeling framework to assess the impact of projected hydroclimatic conditions on water resource systems and hydropower generation. The integrated framework samples climate model outputs under different scenarios to force a hydrologic model and produces streamflow projections. The projected streamflows are inputs for the future hydropower potential assessment. We implement the framework in the central Himalayan river basin. Our results demonstrate substantial spatiotemporal variability in different water balance components (precipitation, evapotranspiration, and water yield) under current and future climatic conditions. For the Himalayan Tila river basin, the annual average energy production is expected to increase under future hydroclimatic conditions (up to 39% in Tila-2 hydropower project, suggested by ensemble mean). Furthermore, this increase in energy is driven mainly by the increased streamflow projections, particularly during the dry season and in the late century. Our results highlight the impacts of hydroclimatic variability in hydropower productions and are of practical use to provide decision-relevant information for designing and operating hydropower infrastructures. The integrated modeling framework presented here is region-specific; however, the approach is reproducible, and the overall insights are generalizable across the Himalayan region.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1987

The effect of front-to-rear propeller spacing on the interaction noise of a model counterrotation propeller at cruise conditions

The effect of front-to-rear propeller spacing on the interaction noise of a counterrotation propeller model was measured at cruise conditions. The data taken at an axial Mach number of 0.80 behaved as expected: interaction noise was reduced with increased spacing. The data taken at M=0.76 and M=0.72 did not behave as expected. At some of the test conditions the noise was unchanged; others even showed noise increases with increased spacing. A possible explanation, involving the amount of downstream blade area impacted by the tip vortex, is presented.

Dittmar, James H.↗