Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “chemically reacting flows”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

A laser flash photolysis-resonance fluorescence kinetics study of the reaction Cl/2P/ + CH4 yields CH3 + HCl

The technique of laser flash photolysis-resonance fluorescence is employed to study the kinetics of the reaction Cl(2P) + CH4 yields CH3 + HCl over the temperature range 221-375 K. At temperatures less than or equal to 241 K the apparent bimolecular rate constant is found to be dependent upon the identity of the chemically inert gases in the reaction mixture. For Cl2/CH4/He reaction mixtures (total pressure = 50 torr) different bimolecular rate constants are measured at low and high methane concentrations. For Cl2/CH4/CCl/He and Cl2/CH4/Ar reaction mixtures, the bimolecular rate constant is independent of methane concentration, being approximately equal to the rate constant measured at low methane concentrations for Cl2/CH4/He mixtures. These rate constants are in good agreement with previous results obtained using the discharge flow-resonance fluorescence and competitive chlorination techniques. At 298 K the measured bimolecular rate constant is independent of the identity of the chemically inert gases in the reaction mixture and in good agreement with all previous investigations. The low-temperature results obtained in this investigation and all previous investigations can be rationalized in terms of a model which assumes that the Cl(2P 1/2) state reacts with CH4 much faster than the Cl(2P 3/2) state. Extrapolation of this model to higher temperatures, however, is not straightforward.

Ravishankara, A. R.↗
DOE OSTI2022

Mesoflow: An Open-Source Reacting Flow Solver for Catalysis at Mesoscale

We present the capabilities and software performance metrics of our open-source continuum solver for catalysis, Mesoflow, developed specifically for modeling transport and chemistry at the mesoscale. Our solver utilizes Cartesian block-structured adaptive mesh refinement to resolve complex catalyst surface morphologies directly obtained from X-ray tomography data. An immersed boundary based formulation enables rapid representation of complex geometries prevalent in most mesoporous catalyst interfaces. The solver is developed on top of open-source performance portable library, AMReX, providing parallel execution capabilities on current and upcoming high-performance-computing (HPC) architectures. Our flexible software framework enables integration of complex chemical mechanisms at heterogenous interfaces and time-split algorithms for circumventing highly disparate reaction and flow time-scales. Our current studies indicate a ten-fold performance gain by using graphics-processing-units (GPUs) compared to a single processor for representative problem sizes (2 million cell mesh). We will also present a brief introduction on how to build and use this software for application problems pertaining to catalytic upgrading and gas transport within porous catalyst particles.

adaptive meshing↗
NASA NTRS1986

Batch Gas-Sampling System

Sampler collects air or other gases in consistent way and stabilizes them for later chemical analysis. Device used for concentrations ranging from few parts per million to 100 percent. Also separates and collects particles in gas for analysis. Gas flows into vacuum sphere when solenoid valve opened. As it passes through conversion tube, constituent of gas forms stable compound that remains in conversion tube for analysis at later time. Sampler parts made of glass, polytetrafluoroethylene, and stainless steel so they do not react with sample.

Diaz, Vernon, Jr.↗
NASA NTRS1993

Computation of wake/exhaust mixing downstream of advanced transport aircraft

The mixing of engine exhaust with the vortical wake of high speed aircraft operating in the stratosphere can play an important role in the formation of chemical products that deplete atmospheric ozone. An accurate analysis of this type of interaction is therefore necessary as a part of the assessment of the impact of proposed High Speed Civil Transport (HSCT) designs on atmospheric chemistry. This paper describes modifications to the parabolic Navier-Stokes flow field analysis in the UNIWAKE unified aircraft wake model to accommodate the computation of wake/exhaust mixing and the simulation of reacting flow. The present implementation uses a passive chemistry model in which the reacting species are convected and diffused by the fluid dynamic solution but in which the evolution of the species does not affect the flow field. The resulting analysis, UNIWAKE/PCHEM (Passive CHEMistry) has been applied to the analysis of wake/exhaust flows downstream of representative HSCT configurations. The major elements of the flow field model are described, as are the results of sample calculations illustrating the behavior of the thermal exhaust plume and the production of species important to the modeling of condensation in the wake. Appropriate steps for further development of the UNIWAKE/PCHEM model are also outlined.

Quackenbush, Todd R.↗
NASA NTRS1993

Numerical solutions of the complete Navier-Stokes equations

The objective of this study is to compare the use of assumed pdf (probability density function) approaches for modeling supersonic turbulent reacting flowfields with the more elaborate approach where the pdf evolution equation is solved. Assumed pdf approaches for averaging the chemical source terms require modest increases in CPU time typically of the order of 20 percent above treating the source terms as 'laminar.' However, it is difficult to assume a form for these pdf's a priori that correctly mimics the behavior of the actual pdf governing the flow. Solving the evolution equation for the pdf is a theoretically sound approach, but because of the large dimensionality of this function, its solution requires a Monte Carlo method which is computationally expensive and slow to coverage. Preliminary results show both pdf approaches to yield similar solutions for the mean flow variables.

Hassan, H. A.↗
NASA NTRS2006

Analysis of a Cylindrical Specimen Heated by an Impinging Hot Hydrogen Jet

A computational conjugate heat transfer methodology was developed, as a first step towards an efficient and accurate multiphysics, thermo-fluid computational methodology to predict environments for hypothetical solid-core, nuclear thermal engine thrust chamber and components. A solid conduction heat transfer procedure was implemented onto a pressure-based, multidimensional, finite-volume, turbulent, chemically reacting, thermally radiating, and unstructured grid computational fluid dynamics formulation. The conjugate heat transfer of a cylindrical material specimen heated by an impinging hot hydrogen jet inside an enclosed test fixture was simulated and analyzed. The solid conduction heat transfer procedure was anchored with a standard solid heat transfer code. Transient analyses were then performed with ,variable thermal conductivities representing three composites of a material utilized as flow element in a legacy engine test. It was found that material thermal conductivity strongly influences the transient heat conduction characteristics. In addition, it was observed that high thermal gradient occur inside the cylindrical specimen during an impulsive or a 10 s ramp start sequence, but not during steady-state operations.

Wang, Ten-See↗
NASA NTRS1993

The validation and application of numerical modelling to supersonic mixing and reacting flows

This study demonstrates that the computational fluid dynamics (CFD) code GASP can be used to predict the features for flowfields representative of scramjet combustors. The validation program undertaken was composed of two parts: a low enthalpy mixing study and a simplified autoignition study. The low enthalpy mixing study was done using low angle helium injection into a Mach 6 airstream over a flat plate. Both matched and overpressurized injection cases were numerically modelled. The agreement with experimental data for the farfield bulk mixing in both cases was reasonable. The combustion studies modelled premixed hydrogen-air reaction with the results being evaluated qualitatively. GASP proved to be highly sensitive to the chemical species present for flow near the ignition temperature, but provided reasonable qualitative results for a subsonic flameholder model.

Vitt, Paul H.↗
NASA NTRS2000

Effect of Jet Injection Angle and Number of Jets on Mixing and Emissions From a Reacting Crossflow at Atmospheric Pressure

The mixing of air jets into hot, fuel-rich products of a gas turbine primary zone is an important step in staged combustion. Often referred to as "quick quench," the mixing occurs with chemical conversion and substantial heat release. An experiment has been designed to simulate and study this process, and the effect of varying the entry angle (0 deg, 22.5 deg and 45 deg from normal) and number of the air jets (7, 9, and 11) into the main flow, while holding the jet-to-crossflow mass-low ratio, MR, and momentum-flux ratio, J, constant (MR = 2.5;J = 25). The geometry is a crossflow confined in a cylindrical duct with side-wall injection of jets issuing from orifices equally spaced around the perimeter. A specially designed reactor, operating on propane, presents a uniform mixture to a module containing air jet injection tubes that can be changed to vary orifice geometry. Species concentrations of O2, CO, CO2, NO(x) and HC were obtained one duct diameter upstream (in the rich zone), and primarily one duct radius downstream. From this information, penetration of the jet, the spatial extent of chemical reaction, mixing, and the optimum jet injection angle and number of jets can be deduced.

St.John, D.↗
NASA NTRS1991

Jet-A reaction mechanism study for combustion application

Simplified chemical kinetic reaction mechanisms for the combustion of Jet A fuel was studied. Initially, 40 reacting species and 118 elementary chemical reactions were chosen based on a literature review. Through a sensitivity analysis with the use of LSENS General Kinetics and Sensitivity Analysis Code, 16 species and 21 elementary chemical reactions were determined from this study. This mechanism is first justified by comparison of calculated ignition delay time with the available shock tube data, then it is validated by comparison of calculated emissions from the plug flow reactor code with in-house flame tube data.

Lee, Chi-Ming↗
DOE OSTI2021

Reactivity of CO 2 with Utica, Marcellus, Barnett, and Eagle Ford Shales and Impact on Permeability

We report that in order to reduce greenhouse gas emissions while recovering hydrocarbons from unconventional shale formations, processes that make use of carbon dioxide to enhance oil recovery while storing carbon dioxide (CO 2 ) should be considered. Here, we examine samples from three shale basins across the United States (Utica and Marcellus Shales in the Appalachian Basin, Barnett Shale in the Bend Arch-Ft. Worth Basin, and Eagle Ford in the Western Gulf Basin) to address the following questions: (1) do changes from reaction with CO 2 and fluids at the micrometer and nanometer scale alter flow pathways and, in turn, impact hydrocarbon production, CO 2 storage, and seal integrity and (2) can CO 2 or fluid reactivity be predicted based on physical or chemical properties of shale formations? Experiments were conducted at 40 °C and 10.3 MPa to characterize the interaction between CO 2 and shale using X-ray diffraction (XRD), carbon and sulfur analysis, in situ Fourier transform infrared spectroscopy (FT-IR), feature relocation scanning electron microscopy coupled with energy-dispersive spectroscopy (SEM-EDS), mercury (Hg) intrusion porosimetry, and Brunauer-Emmett-Teller (BET) surface area and pore size analysis coupled with density functional theory (DFT) methods. Changes in mechanical, physical, and flow properties of shale cores due to CO 2 exposure were addressed using a New England Research Autolab 1500 and Xenon X-ray computed tomography (CT) scanning. Results showed that CO 2 did not promote significant reactivity with the shale if water was not present; only shales with swelling clays or residual interstitial pore water reacted with dry CO 2 to promote reactivity in shale. When water was added as a reactant, CO 2 formed carbonic acid and reacted with the shale to dissolve carbonate pockets, etched and pitted the shale matrix surfaces, and increased the microporosity and decreased nanoporosity. Porosity and permeability increased appreciably in core shale samples after exposure to CO 2 saturated fluid due to dissolution of carbonate. Shale mechanical properties were not altered. Trends were not observed that could tie CO 2 or fluid reactivity to physical or chemical properties of the shale formations at the basin scale from the samples we examined. However, if the shale contained significant amounts of carbonate and water was available to react with the CO 2 , pore sizes were altered in the matrix and permeability and porosity increased.

04 OIL SHALES AND TAR SANDS↗
NASA NTRS1991

Jet-A reaction mechanism study for combustion application

Simplified chemical kinetic reaction mechanisms for the combustion of Jet A fuel are studied. Initially 40 reacting species and 118 elementary chemical reactions were chosen based on the literature review of previous works. Through a sensitivity analysis with the use of LSENS General Kinetics and Sensitivity Analysis Code, 16 species and 21 elementary chemical reactions were determined from this study. This mechanism is first justified by comparison of calculated ignition delay time with available shock tube data, then it is validated by comparison of calculated emissions from plug flow reactor code with in-house flame tube data.

Lee, Chi-Ming↗
NASA NTRS1998

An Integrated Tool for the Coupled Thermal and Mechanical Analysis of Pyrolyzing Heatshield Materials

Materials that pyrolyze at elevated temperature have been commonly used as thermal protection materials in hypersonic flight, and advanced pyrolyzing materials for this purpose continue to be developed. Because of the large temperature gradients that can arise in thermal protection materials, significant thermal stresses can develop. Advanced applications of pyrolytic materials are calling for more complex heatshield configurations, making accurate thermal stress analysis more important, and more challenging. For non-pyrolyzing materials, many finite element codes are available and capable of performing coupled thermal-mechanical analyses. These codes do not, however, have a built-in capability to perform analyses that include pyrolysis effects. When a pyrolyzing material is heated, one or more components of the original virgin material pyrolyze and create a gas. This gas flows away from the pyrolysis zone to the surface, resulting in a reduction in surface heating. A porous residue, referred to as char, remains in place of the virgin material. While the processes involved can be complex, it has been found that a simple physical model in which virgin material reacts to form char and pyrolysis gas, will yield satisfactory analytical results. Specifically, the effects that must be modeled include: (1) Variation of thermal properties (density, specific heat, thermal conductivity) as the material composition changes; (2) Energy released or absorbed by the pyrolysis reactions; (3) Energy convected by the flow of pyrolysis gas from the interior to the surface; (4) The reduction in surface heating due to surface blowing; and (5) Chemical and mass diffusion effects at the surface between the pyrolysis gas and edge gas Computational tools for the one-dimensional thermal analysis these materials exist and have proven to be reliable design tools. The objective of the present work is to extend the analysis capabilities of pyrolyzing materials to axisymmetric configurations, and to couple thermal and mechanical analyses so that thermal stresses may be efficiently and accurately calculated.

Pronchick, Stephen W.↗
NASA NTRS2011

Developing Flexible, High Performance Polymers with Self-Healing Capabilities

Flexible, high performance polymers such as polyimides are often employed in aerospace applications. They typically find uses in areas where improved physical characteristics such as fire resistance, long term thermal stability, and solvent resistance are required. It is anticipated that such polymers could find uses in future long duration exploration missions as well. Their use would be even more advantageous if self-healing capability or mechanisms could be incorporated into these polymers. Such innovative approaches are currently being studied at the NASA Kennedy Space Center for use in high performance wiring systems or inflatable and habitation structures. Self-healing or self-sealing capability would significantly reduce maintenance requirements, and increase the safety and reliability performance of the systems into which these polymers would be incorporated. Many unique challenges need to be overcome in order to incorporate a self-healing mechanism into flexible, high performance polymers. Significant research into the incorporation of a self-healing mechanism into structural composites has been carried out over the past decade by a number of groups, notable among them being the University of I1linois [I]. Various mechanisms for the introduction of self-healing have been investigated. Examples of these are: 1) Microcapsule-based healant delivery. 2) Vascular network delivery. 3) Damage induced triggering of latent substrate properties. Successful self-healing has been demonstrated in structural epoxy systems with almost complete reestablishment of composite strength being achieved through the use of microcapsulation technology. However, the incorporation of a self-healing mechanism into a system in which the material is flexible, or a thin film, is much more challenging. In the case of using microencapsulation, healant core content must be small enough to reside in films less than 0.1 millimeters thick, and must overcome significant capillary and surface tension forces to flow, mix and react to achieve healing. Vascular networks small enough to fit into such films must also overcome these same flow limitations. Self-healing has also been demonstrated in ionomeric substrates such as Surlyn , wherein the heat generated by a projectile impact triggers the latent ability of this substrate to flow back to its original shape. Recent work using Diels-Alder reactions have shown promise in bringing about actual reforming of broken chemical bonds to achieve self-healing [2]. All self-healing mechanisms that rely on the use of inherent latent substrate properties require some degree of polymer chain flow to achieve any significant level of healing.

Jolley, Scott T.↗
NASA NTRS1989

Two-dimensional analysis of two-phase reacting flow in a firing direct-injection diesel engine

The flow field, spray penetration, and combustion in two-stroke diesel engines are described. Fuel injection begins at 345 degrees after top dead center (ATDC) and n-dodecane is used as the liquid fuel. Arrhenius kinetics is used to calculate the reaction rate term in the quasi-global combustion model. When the temperature, fuel, and oxygen mass fraction are within suitable flammability limits, combustion begins spontaneously. No spark is necessary to ignite a localized high temperature region. Compression is sufficient to increase the gaseous phase temperature to a point where spontaneous chemical reactions occur. Results are described for a swirl angle of 22.5 degrees.

Nguyen, H. Lee↗
NASA NTRS1977

Chemical kinetic modeling of propane oxidation behind shock waves

The stoichiometric combustion of propane behind incident shock waves was studied experimentally and analytically over a temperature range from 1700 K to 2600 K and a pressure range from 1.2 to 1.9 atm. Measurements of the concentrations of carbon monoxide (CO) and carbon dioxide (CO2) and the product of the oxygen atom and carbon dioxide concentrations (O)(CO) were made after passage of the incident shock wave. A kinetic mechanism was developed which, when used in a computer program for a flowing, reacting gas behind an incident shock wave predicted experimentally measured results quite well. Ignition delay times from the literature were also predicted quite well. The kinetic mechanism consisted of 59 individual kinetic steps.

Mclain, A. G.↗
NASA NTRS1982

Catalytic recombination and Space Shuttle heating

The measurement of surface temperatures on the thermal protection materials of the Space Shuttle Orbiter during reentry provides the basis for an important test of the prediction techniques developed over the past 10 years for reacting flows over reentry vehicles. The present investigation is concerned with comparisons of calculated temperatures with those measured during the second and third Space Shuttle missions. The general trends of the calculations compared favorably with the measurements. However, the calculations overpredicted the temperatures on the forward part of the windward centerline. Agreement was better farther aft, especially at the later times in the entry. The investigation has pointed out the significance of surface chemical reactions on the heat flux to the surface of the Orbiter and the need for further understanding.

Scott, C. D.↗
DOE OSTI2022

Comprehensive uncertainty quantification (UQ) for full engineering models by solving probability density function (PDF) equation

This report details a new method for propagating parameter uncertainty (forward uncertainty quantification) in partial differential equations (PDE) based computational mechanics applications. The method provides full-field quantities of interest by solving for the joint probability density function (PDF) equations which are implied by the PDEs with uncertain parameters. Full-field uncertainty quantification enables the design of complex systems where quantities of interest, such as failure points, are not known apriori. The method, motivated by the well-known probability density function (PDF) propagation method of turbulence modeling, uses an ensemble of solutions to provide the joint PDF of desired quantities at every point in the domain. A small subset of the ensemble is computed exactly, and the remainder of the samples are computed with approximation of the driving (dynamics) term of the PDEs based on those exact solutions. Although the proposed method has commonalities with traditional interpolatory stochastic collocation methods applied directly to quantities of interest, it is distinct and exploits the parameter dependence and smoothness of the dynamics term of the governing PDEs. The efficacy of the method is demonstrated by applying it to two target problems: solid mechanics explicit dynamics with uncertain material model parameters, and reacting hypersonic fluid mechanics with uncertain chemical kinetic rate parameters. A minimally invasive implementation of the method for representative codes SPARC (reacting hypersonics) and NimbleSM (finite- element solid mechanics) and associated software details are described. For solid mechanics demonstration problems the method shows order of magnitudes improvement in accuracy over traditional stochastic collocation. For the reacting hypersonics problem, the method is implemented as a streamline integration and results show very good accuracy for the approximate sample solutions of re-entry flow past the Apollo capsule geometry at Mach 30.

42 ENGINEERING↗
NASA NTRS1986

Self-adaptive difference method for the effective solution of computationally complex problems of boundary layer theory

An implicit difference procedure for the solution of equations for a chemically reacting hypersonic boundary layer is described. Difference forms of arbitrary error order in the x and y coordinate plane were used to derive estimates for discretization error. Computational complexity and time were minimized by the use of this difference method and the iteration of the nonlinear boundary layer equations was regulated by discretization error. Velocity and temperature profiles are presented for Mach 20.14 and Mach 18.5; variables are velocity profiles, temperature profiles, mass flow factor, Stanton number, and friction drag coefficient; three figures include numeric data.

Schoenauer, W.↗