Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “behavior modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

Calculation of the Aerodynamic Behavior of the Tilt Rotor Aeroacoustic Model (TRAM) in the DNW

Comparisons of measured and calculated aerodynamic behavior of a tiltrotor model are presented. The test of the Tilt Rotor Aeroacoustic Model (TRAM) with a single, 1/4-scale V- 22 rotor in the German-Dutch Wind Tunnel (DNW) provides an extensive set of aeroacoustic, performance, and structural loads data. The calculations were performed using the rotorcraft comprehensive analysis CAMRAD II. Presented are comparisons of measured and calculated performance and airloads for helicopter mode operation, as well as calculated induced and profile power. An aerodynamic and wake model and calculation procedure that reflects the unique geometry and phenomena of tiltrotors has been developed. There are major differences between this model and the corresponding aerodynamic and wake model that has been established for helicopter rotors. In general, good correlation between measured and calculated performance and airloads behavior has been shown. Two aspects of the analysis that clearly need improvement are the stall delay model and the trailed vortex formation model.

Johnson, Wayne↗
NASA NTRS2012

A Model-Based Approach to Engineering Behavior of Complex Aerospace Systems

One of the most challenging yet poorly defined aspects of engineering a complex aerospace system is behavior engineering, including definition, specification, design, implementation, and verification and validation of the system's behaviors. This is especially true for behaviors of highly autonomous and intelligent systems. Behavior engineering is more of an art than a science. As a process it is generally ad-hoc, poorly specified, and inconsistently applied from one project to the next. It uses largely informal representations, and results in system behavior being documented in a wide variety of disparate documents. To address this problem, JPL has undertaken a pilot project to apply its institutional capabilities in Model-Based Systems Engineering to the challenge of specifying complex spacecraft system behavior. This paper describes the results of the work in progress on this project. In particular, we discuss our approach to modeling spacecraft behavior including 1) requirements and design flowdown from system-level to subsystem-level, 2) patterns for behavior decomposition, 3) allocation of behaviors to physical elements in the system, and 4) patterns for capturing V&V activities associated with behavioral requirements. We provide examples of interesting behavior specification patterns, and discuss findings from the pilot project.

SysML↗
NASA NTRSDate not supplied

Hybrid Model Based Approaches for Systems Health Management and Prognostics

To facilitate and solve the prediction problem, awareness of the current health state of the system is key, since it is necessary to perform condition-based predictions. To accurately predict the future state of any system, it is required to possess knowledge of its current health state and future operational conditions. Latest achievements of data-driven algorithms in regression of complex nonlinear functions and classification tasks have generated a growing interest in artificial intelligence for industrial applications. Complex multi-physics models as well as digital twins, once purely built on physics and corresponding simplified lumped parameter iterations, can now benefit from machine learning algorithms to mitigate the lack of understanding of some complex behavior. Given models of the current and future system behavior, a general approach of model-based prognostics can solve the prediction problem and further decision making. In principle, data driven approaches can replace expensive experimental test-setups as well as reduce the number of simulations needed to explore, e.g., the parametric space of a multi-parameter model. Nonetheless, the limitations of pure data-driven methods came to light rather quickly, at least for some industries. In many industrial applications, data acquisition is costly, and the volume of data that can be collected does not satisfy the requirements for an effective model training and cross-validation. Therefore, some recent works in the area of machine learning is focusing on blending physics with data-driven algorithms, thus mitigating the drawbacks of the two approaches and emphasizing respective advantages. Partial physical knowledge of the problem can aid the learning process by “guiding” the algorithm towards efficient solutions that satisfy the physics driving the system behavior. The result is a hybrid modeling approach combining physical knowledge as well data driven methods to develop a unified hybrid approach. A hybrid framework for fusing information from physics-based performance models along with deep learning algorithms for prognostics of complex safety critical systems is presented. In this framework, physics-based performance models infer unobservable model parameters related to the system's components health solving a calibration problem in the deep learning approach.

Hybrid Modeling↗
NASA NTRSDate not supplied

Hybrid Approaches to Systems Health Management and Prognostics

To facilitate and solve the prediction problem, awareness of the current health state of the system is key, since it is necessary to perform condition-based predictions. To accurately predict the future state of any system, it is required to possess knowledge of its current health state and future operational conditions. Latest achievements of data-driven algorithms in regression of complex nonlinear functions and classification tasks have generated a growing interest in artificial intelligence for industrial applications. Complex multi-physics models as well as digital twins, once purely built on physics and corresponding simplified lumped parameter iterations, can now benefit from machine learning algorithms to mitigate the lack of understanding of some complex behavior. Given models of the current and future system behavior, a general approach of model-based prognostics can solve the prediction problem and further decision making. In principle, data driven approaches can replace expensive experimental test-setups as well as reduce the number of simulations needed to explore, e.g., the parametric space of a multi-parameter model. Nonetheless, the limitations of pure data-driven methods came to light rather quickly, at least for some industries. In many industrial applications, data acquisition is costly, and the volume of data that can be collected does not satisfy the requirements for an effective model training and cross-validation. Therefore, some recent works in the area of machine learning is focusing on blending physics with data-driven algorithms, thus mitigating the drawbacks of the two approaches and emphasizing respective advantages. Partial physical knowledge of the problem can aid the learning process by “guiding” the algorithm towards efficient solutions that satisfy the physics driving the system behavior. The result is a hybrid modeling approach combining physical knowledge as well data driven methods to develop a unified hybrid approach. A hybrid framework for fusing information from physics-based performance models along with deep learning algorithms for prognostics of complex safety critical systems is presented. In this framework, physics-based performance models infer unobservable model parameters related to the system's components health solving a calibration problem in the deep learning approach.

Systems Health Management↗
NASA NTRS2022

Hybrid Model Based Approaches for Systems Health Management and Prognostics

This is a previously approved and published presentation. To accurately predict the future state of any system, it is required to possess knowledge of its current health state and future operational conditions. Present achievements of data-driven algorithms in regression of complex nonlinear functions and classification tasks have generated a growing interest in artificial intelligence for industrial applications. Complex multi-physics models as well as digital twins, once purely built on physics and corresponding simplified lumped parameter iterations, can now benefit from machine learning algorithms to mitigate the lack of understanding of some complex behavior. Given models of the current and future system behavior, a general approach of model-based prognostics can solve the prediction problem and further decision-making. In principle, data-driven approaches can replace expensive experimental test-setups as well as reduce the number of simulations needed to explore, e.g., the parametric space of a multi-parameter model. Nonetheless, the limitations of pure data-driven methods came to light rather quickly, at least for some industries. In many industrial applications, data acquisition is costly, and the volume of data that can be collected does not satisfy the requirements for effective model training and cross-validation. Therefore, some recent works in the area of machine learning is focusing on blending physics with data-driven algorithms, thus mitigating the drawbacks of the two approaches and emphasizing respective advantages. Partial physical knowledge of the problem can aid the learning process by “guiding” the algorithm towards efficient solutions that satisfy the physics driving the system behavior. The result is a hybrid modeling approach combining physical knowledge as well data-driven methods to develop a unified hybrid approach. A hybrid framework for fusing information from physics-based performance models along with deep learning algorithms for prognostics of complex safety-critical systems is presented. In this framework, physics-based performance models infer unobservable model parameters related to the system's components health solving a calibration problem in the deep learning approach.

Prognostics↗
DOE OSTI2022

Creep Behavior and Phase Equilibria in Model Precipitate Strengthened Alumina-Forming Austenitic Alloys

Abstract Creep-rupture behavior and microstructural response in alumina-forming austenitic (AFA) alloys with two different precipitation strengthening mechanisms, “Laves-phase + M 23 C 6 carbide” and “coherent L1 2 γ′-Ni 3 (Al,Ti),” were explored as “model” cases of multi-phase, multi-scale heat-resistant AFA alloys for 650–750°C use. These alloys will be used to guide and verify computational alloy design and life-prediction modeling under an on-going eXtremeMAT project through the Office of Fossil Energy and Carbon Management, US Department of Energy. Computational thermodynamics were used to design and predict the amounts of strengthening and deteriorating secondary phases at 750°C. Creep-rupture lives of the alloys tested at 750°C and 100 MPa were in a range of 4000–9000 h, and the microstructure at the gage/grip after creep-rupture testing was compared with isothermally aged alloys for 1500 h, as well as the calculated phases. Detailed microstructure characterization includes phase identification, volume fraction measurement, and compositional analysis, which were correlated with the creep-rupture properties. High-temperature oxidation resistance was also screened and compared with commercial, chromia-forming heat-resistant steels. These model alloys also provide the basis for further design and optimization of next generation AFA alloys with improved creep resistance.

36 MATERIALS SCIENCE↗
NASA NTRS1992

Vibrational behavior of adaptive aircraft wing structures modelled as composite thin-walled beams

The vibrational behavior of cantilevered aircraft wings modeled as thin-walled beams and incorporating piezoelectric effects is studied. Based on the converse piezoelectric effect, the system of piezoelectric actuators conveniently located on the wing yield the control of its associated vertical and lateral bending eigenfrequencies. The possibility revealed by this study enabling one to increase adaptively the eigenfrequencies of thin-walled cantilevered beams could play a significant role in the control of the dynamic response and flutter of wing and rotor blade structures.

Song, O.↗
DOE OSTI2021

A Data Set for Intercomparing the Transient Behavior of Dynamical Model-Based Subseasonal to Decadal Climate Predictions

Climate predictions using coupled models in different time scales, from intraseasonal to decadal, are usually affected by initial shocks, drifts, and biases, which reduce the prediction skill. These arise from inconsistencies between different components of the coupled models and from the tendency of the model state to evolve from the prescribed initial conditions toward its own climatology over the course of the prediction. Aiming to provide tools and further insight into the mechanisms responsible for initial shocks, drifts, and biases, this paper presents a novel data set developed within the Long Range Forecast Transient Intercomparison Project, LRFTIP. This data set has been constructed by averaging hindcasts over available prediction years and ensemble members to form a hindcast climatology, that is a function of spatial variables and lead time, and thus results in a useful tool for characterizing and assessing the evolution of errors as well as the physical mechanisms responsible for them. A discussion on such errors at the different time scales is provided along with plausible ways forward in the field of climate predictions

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

VpROM: a novel variational autoencoder-boosted reduced order model for the treatment of parametric dependencies in nonlinear systems

Reduced Order Models (ROMs) are of considerable importance in many areas of engineering in which computational time presents difficulties. Established approaches employ projection-based reduction, such as Proper Orthogonal Decomposition. The limitation of the linear nature of such operators is typically tackled via a library of local reduction subspaces, which requires the assembly of numerous local ROMs to address parametric dependencies. Our work attempts to define a more generalisable mapping between parametric inputs and reduced bases for the purpose of generative modeling. We propose the use of Variational Autoencoders (VAEs) in place of the typically utilised clustering or interpolation operations, for inferring the fundamental vectors, termed as modes, which approximate the manifold of the model response for any and each parametric input state. The derived ROM still relies on projection bases, built on the basis of full-order model simulations, thus retaining the imprinted physical connotation. However, it additionally exploits a matrix of coefficients that relates each local sample response and dynamics to the global phenomena across the parametric input domain. The VAE scheme is utilised for approximating these coefficients for any input state. This coupling leads to a high-precision low-order representation, which is particularly suited for problems where model dependencies or excitation traits cause the dynamic behavior to span multiple response regimes. Moreover, the probabilistic treatment of the VAE representation allows for uncertainty quantification on the reduction bases, which may then be propagated to the ROM response. The performance of the proposed approach is validated on an open-source simulation benchmark featuring hysteresis and multi-parametric dependencies, and on a large-scale wind turbine tower characterised by nonlinear material behavior and model uncertainty.

Conditional VAEs↗
DOE OSTI2022

Physical Modeling of Coupled Thermohydraulic Behavior of Compacted MX80 Bentonite during Heating

Abstract This paper describes a tank-scale test setup and experimental methodology used to investigate coupled heat transfer and water flow processes during heating of compacted MX80 bentonite to high temperatures. Specifically, a temperature of 200°C was maintained by a cylindrical heating element at the center of a compacted bentonite layer containing an array of temperature, dielectric, and relative humidity sensors. In addition to providing an evaluation of the spatiotemporal variations in temperature, relative humidity, degree of saturation, and global volume, the coupled thermohydraulic properties of the bentonite were assessed. A wetting front was initially observed to move away from the central heater, followed by a drying process until reaching thermohydraulic equilibrium. The soil–water retention curve (SWRC) of the bentonite followed a wetting scanning path before following the primary drying path exhibiting a shift in water retention with elevated temperature. Results from the tank-scale test can be used for validation of numerical simulations of drying processes in the engineered barrier system of a high-level radioactive waste geological disposal repository and confirm that a temperature-dependent hysteretic SWRC with scanning paths is required to accurately capture the bentonite response.

Engineering↗
NASA NTRS1984

Elastic model of the traction behavior of two traction lubricants

In the analysis of rolling-sliding concentrated contacts, such as gears, bearings and traction drives, the traction characteristics of the lubricant are of prime importance. The elastic shear modulus and limiting shear stress properties of the lubricant dictate the traction/slip characteristics and power loss associated with an EHD contact undergoing slip and/or spin. These properties can be deducted directly from the initial slope m and maximum traction coefficient micron of an experimental traction curve. In this investigation, correlation equations are presented to predict m and micron for two modern traction fluids based on the regression analysis of 334 separate traction disk machine experiments. The effects of contact pressure, temperature, surface velocity, ellipticity ratio are examined. Problems in deducing lubricant shear moduli from disk machine tests are discussed. Previously announced in STAR as N83-20116

Loewenthal, S. H.↗
NASA NTRS1992

Experimental, physical and numerical modeling of lunar regolith and lunar regolith structures

An extensive series of laboratory strength and deformation experiments have been performed on a lunar regolith simulant. Results of these experiments are compared to results from experiments on real lunar regolith from the Apollo and Luna missions to illustrate the suitability of this material in capturing the engineering properties lunar regolith. In addition, these results are used to calibrate a constitutive model used to describe its stress-strain behavior. This model, in conjunction with numerical analysis techniques, is used to predict the response i.e. material parameters) of lunar simulant under 1/6-g and low confining stress conditions. These tools are also used to predict the displacement response of a lunar soil embankment structure used to cover a first generation human habitat module, which might be used to accommodate the first astronauts revisiting the moon. These predictions are compared to physical models of this structure, which are tested in a geotechnical centrifuge in order to satisfy scaling relationships between prototype and model.

Perkins, Steven W.↗
NASA NTRS2014

Attendee Response to Guiding Questions of the September 2014 DOE Workshop on North Slope of Alaska Priorities

We advocate for several modeling approaches suitable to prove understanding of and capability to model aerosol behavior in nucleating droplets and ice and to model regional cloud systems at the mesoscale. The full complement of data that is ideal for particular study types is increasingly well understood; the ASR ISDAC Science Plan provides an excellent example of listing the data required for each study type targeted by that campaign. Whereas discussion here focused on the microscale and mesoscale, other studies should obviously focus on the regional, seasonal and global scale. When considering ice microphysics alone, laser focus on unconstrained model components could be usefully intensified (e.g., collision-coalescence kernels). Similarly, a focus on boundary layer structure would be deeply valuable to a wide range of model types. The expense of observations motivates efficient planning for observational data sets to support specific study approaches; the concept of closure is often useful (e.g., the surface energy budget).

nucleation↗