Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “barriers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Analysis of metal temperature and coolant flow with a thermal-barrier coating on a full-coverage-film-cooled turbine vane

The potential benefits of combining full-coverage film cooling with a thermal-barrier coating were investigated analytically for sections on the suction and pressure sides a high-temperature, high-pressure turbine vane. Metal and ceramic coating temperatures were calculated as a function of coating thickness and coolant flow. With a thermal-barrier coating, the coolant flows required for the chosen sections were half those of an uncoated design, and the metal outer temperatures were simultaneously reduced by over 111 K (200 F). For comparison, transpiration cooling was also investigated. Full-coverage film cooling of a coated vane required more coolant flow than did transpiration cooling.

Meitner, P. L.↗
NASA NTRS1978

Low-cycle fatigue of thermal-barrier coatings at 982 deg C

The low-cycle fatigue lives of ZrO2-NiCrAlY and Al2O3-ZrO2-NiCrAlY thermal-barrier coatings in air at 982 C were determined from cyclic flexural tests of coated TAZ-8A strips. Strains were computed as a function of specimen displacements from a nonlinear, three-dimensional stress analysis program. Fatigue resistances of thermal-barrier coatings applied to the strips were compared with those of uncoated and NiCrAlY-coated strips. The results indicate that ZrO2 is about four times greater in fatigue life than TAZ-8A at 982 C, that ZrO2 would probably retain that fatigue strength up to 1316 C, and that adding an outer coat of Al2O3 to ZrO2 is neither beneficial nor detrimental to fatigue resistance.

Kaufman, A.↗
NASA NTRS1980

Corrosion-resistant ceramic thermal barrier coating

Two-layer thermal barrier coating, consisting of metal-CrA1Y bond coating and calcium silicate ceramic outer layer, greatly improves resistance of turbine parts to hot corrosion from fuel and air impurities. Both layers can be plasma sprayed, and ceramic layer may be polished to reduce frictional losses. Ceramic provides thermal barrier, so parts operate cooler metal temperatures, coolant flow can be reduced, or gas temperatures increased. Lower grade fuels also can be used.

Hodge, P. E.↗
NASA NTRS1980

Effects of yttrium, aluminum and chromium concentrations in bond coatings on the performance of zirconia-yttria thermal barriers

A cyclic furnace study was conducted on thermal barrier systems to evaluate the effects of yttrium, chromium, and aluminum in nickel-base alloy bond coatings and the effect of bond coating thickness on yttria-stabilized zirconia thermal barrier coating life. Without yttrium in the bond coatings, the zirconia coatings failed very rapidly. Increasing chromium and aluminum in the Ni-Cr-Al-Y bond coatings increased total coating life. This effect was not as great as that due to yttrium. Increased bond coat thickness was also found to increase life.

Stecura, S.↗
NASA NTRS1980

Evaluation of hot corrosion behavior of thermal barrier coatings

Calcium silicate and yttria stabilized zirconia/MCrAlY thermal barrier coating systems on air-cooled specimens were exposed to sodium plus vanadium doped Mach 0.3 combustion gases. Thermal barrier coating endurance was determined to be a strong inverse function of ceramic coating thickness. Coating system durability was increased through the use of higher Cr + Al NiCrAl and CoCrAlY bond coatings. Chemical and electron microprobe analyses supported the predictions of condensate compositions and the determination of their roles in causing spalling of the ceramic coatings.

Hodge, P. E.↗
NASA NTRS1980

Performance of two-layer thermal barrier systems on directionally solidified Ni-Al-Mo and comparative effects of alloy thermal expansion on system life

A promising two-layer thermal barrier coating system (TBS), Ni-16.4Cr-5.1A1-0.15Y/ZrO2-6.1Y2O3 (all in weight percent), was identified for directionally solidified Ni-Al-Mo (gamma/gamma' alpha). In cyclic furnace tests at 1095 C this system on gamma/gamma' alpha was better than Ni-16. 4Cr-5.1Al-0.15Y/ZrO2-7.8Y2O3 by about 50 percent. In natural gas - oxygen torch rig tests at 1250 C the ZrO2-6.1Y2O3 coating was better than the ZrO2-7.8Y2O3 coating by 95 percent, on MAR-M509 substrates and by 60 percent on gamma/gamma' alpha substrates. Decreasing the coefficient of thermal expansion of the substrate material from 17-18x10 to the -6 power/C (MAR-M200 + Hf and MAR-M509) to 11x10 to the -6 power/C (gamma/gamma' alpha) also resulted in improved TBS life. For example, in natural gas - oxygen torch rig tests at 1250 C, the life of Ni-16.4Cr-5.1Al-0.15Y/ZrO26.1Y2O3 was about 30 percent better on gamma/gamma' alpha than on MAR-M509 substrates. Thus compositional changes in the bond and thermal barrier coatings were shown to have a greater effect on TBS life than does the coefficient of thermal expansion.

Stecura, S.↗
NASA NTRS1980

Effects of yttrium, aluminum and chromium concentrations in bond coatings on the performance of zirconia-yttria thermal barriers

A cyclic furnace study was conducted on thermal barrier systems to evaluate the effects of yttrium, chromium and aluminum in nickel-base alloy bond coatings and the effect of bond coating thickness on yttria-stabilized zirconia thermal barrier coating life. Without yttrium in the bond coatings, the zirconia coatings failed very rapidly. Increasing chromium and aluminum in the Ni-Cr-Al-Y bond coatings increased total coating life. This effect was not as great as that due to yttrium. Increased bond coat thickness was also found to increase life.

Stecura, S.↗
NASA NTRS1980

Investigation of diffusion barrier materials on silicon carbide filaments

The formation of diffusion barrier materials on SiC filaments is discussed. The filaments possess a carbon-rich surface layer and, consequently, are difficult to wet by molten Al and tend to react with the molten metal, degrading filament strength. Characterization of the filament with various CVD barrier materials is reported.

Wawner, F. E.↗
NASA NTRS1981

Assessment of variations in thermal cycle life data of thermal barrier coated rods

The reported study had the purpose to examine variations in cyclic life and in adhesive/cohesive coating strength. Possible effects of heating rate, stress reversal, temperature level, and ceramic deposition methods on coating life were also investigated. Life cycle data for 22 thermal barrier coated rods were examined and found to be statistically modeled by normal or log-normal distributions. The sample mean was 1330 cycles with a standard deviation of 520 cycles. Adhesive/cohesive pulloff strength data for 20 thermal barrier coated flat head piston specimens were taken. The average pulloff stress was 9 MPa with a standard deviation of 4.2 MPa. It was found that variations in heating rate can produce significant variations in the life cycle data.

Hendricks, R. C.↗
NASA NTRS1981

Prolonging thermal barrier coated specimen life by thermal cycle management

Thermal barrier coatings applied to the heated side of engine components such as seals, combustor, and blades of a gas turbine offer a potential increase in efficiency through the use of higher gas temperatures or less cooling air or benefits arising from extended component life by reducing component metal temperatures. The considered investigation has the objective to show that while a thermal barrier coated (TBC) specimen can be brought to a fixed temperature using various fuel-air ratio (F/A) values, lower calculated stresses are associated with lower (F/A) values. This implies that control of (F/A) values (i.e., rates of heat input) during the starting transient and to a lesser extent during shutdown and operation, offers a potential method of improving TBC lifetime through thermal cycle management.

Hendricks, R. C.↗
NASA NTRS1981

Stuffed MO layer as a diffusion barrier in metallizations for high temperature electronics

Auger electron spectroscopy was employed to characterize the diffusion barrier properties of molybdenum in the CrSi2/Mo/Au metallization system. The barrier action of Mo was demonstrated to persist even after 2000 hours annealing time at 300 C in a nitrogen ambient. At 340 C annealing temperature, however, rapid interdiffusion was observed to have occurred between the various metal layers after only 261 hours. The presence of controlled amounts of oxygen in the Mo layer is believed to be responsible for suppressing the short circuit interdiffusion between the thin film layers. Above 340 C, its is believed that the increase in the oxygen mobility led to deterioration of its stuffing action, resulting in the rapid interdiffusion of the thin film layers along grain boundaries.

Boah, J. K.↗
NASA NTRS1981

Review of NASA progress in thermal barrier coatings for stationary gas turbines

Ceramic thermal barrier coatings for industrial/utility gas turbines were investigated. In burner rig tests of a zirconia yttria/nickel chromium aluminum yttrium ZrO2-12w/0Y2O3/NiCrAlY coating system on air cooled superalloy specimens, ceramic coating life (spallation) was sensitive to Na and V concentration in the fuel. The locations of coating spallation correspond to areas where combustion products were predicted to condense. Three new thermal barrier coating systems were identified. These are based on calcium silicate, ZrO2-8w/0Y2O3, and a MgO-NiCrAlY cermet. The spall resistance can be increased by reducing the ceramic layer thickness from 0.038 to 0.013 cm and by the use of more oxidation/corrosion resistant bond coats.

Hodge, P. E.↗
NASA NTRS1982

Evaluation of present thermal barrier coatings for potential service in electric utility gas turbines

The resistance of present-day thermal barrier coatings to combustion gases found in electric utility turbines was assessed. The plasma sprayed coatings, both duplex and graded types, were primarily zirconia-based, although a calcium silicate was also evaluated. Both atmospheric burner rig tests and high pressure tests (135 psig) showed that several present-day thermal barrier coatings have a high potential for service in gas turbines burning the relatively clean GT No. 2 fuel. However, coating improvements are needed for use in turbines burning lower grade fuel such as residual oil. The duplex ZrO2.8Y2O3/NiCrA1Y coating was ranked highest and selected for near-term field testing, with Ca2SiO4/NiCrA1Y ranked second. Graded coatings show potential for corrosive turbine operating conditions and warrant further development. The coating degradation mechanisms for each coating system subjected to the various environmental conditions are also described.

Bratton, R. J.↗
NASA NTRS1982

Barriers and dispersal surfaces in minimum-time interception

Minimum time interception of a target moving in a horizontal plane is analyzed as a one-player differential game. Dispersal points and points on the barrier are located for a class of pursuit evasion and interception problems. These points are determined by constructing cross sections of the isochrones and hence obtaining the barrier, dispersal, and control level surfaces. The game solution maps the controls as a function of the state within the capture region.

Rajan, N.↗
NASA NTRS1980

Evaluation of the hot corrosion behavior of thermal barrier coatings

Calcium silicate and yttria-stabilized ZrO2/(M-Cr-Al-Y) thermal barrier coating systems on air-cooled specimens were exposed to sodium- plus vanadium-doped Mach 0.3 combustion gases. The thermal barrier coating endurance was determined to be a strong inverse function of the ceramic coating thickness. Coating system durability was increased through the use of Ni-Cr-Al-Y and Co-Cr-Al-Y bond coatings with high chromium and aluminum contents. Chemical and electron microprobe analyses supported the predictions of condensate compositions and the determination of their roles in causing spalling of the ceramic coatings.

Hodge, P. E.↗
NASA NTRS1980

Effects of yttrium, aluminum and chromium concentrations in bond coatings on the performance of zirconia-yttria thermal barriers

A cyclic furnace study was conducted on thermal barrier systems to evaluate the effects of yttrium, chromium and aluminum in nickel-base alloy bond coatings and the influence of the bond coating thickness on yttria-stabilized zirconia thermal barrier coating lifetimes. Without yttrium in the bond coatings, the zirconia coatings failed very rapidly. Increasing concentrations of chromium and aluminum in the Ni-Cr-Al-Y bond coatings increased the total coating lifetimes. This effect was not as great as that due to yttrium. Increased bond coating thickness was also found to increase the lifetimes.

Stecura, S.↗
NASA NTRS1980

On the barrier to crystal nucleation in lunar glasses

The paper describes an analytical method for calculating in detail the size distributions of small crystallites and nuclei in supercooled liquids as they are being quenched to form a glass and subsequently reheated above the glass transition to produce crystallization. This method is applied to experiments performed using differential thermal analysis (DTA) to estimate the barriers to crystal nucleation and the cooling rates required to form glasses or bodies with various degrees of crystallinity. DTA data and derived nucleation barriers are reported for anorthite and for the following lunar compositions: 15498, 15418, matrix and intrusion compositions of breccia 15286, Apollo 15 green glass, Luna 24 highland basalt, and 65016.

Yinnon, H.↗