Stripe-line coil for magnetic-field generation in bubble memory devices
Coil etched from conductive film has better field uniformity than wire-wound coils and less coil loss at high-frequency operation.
Chen, T. T.↗
SEARCH · Engineering Papers
Results for “WOUNDS”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Open coil structure for bubble-memory-device packaging
Concept has several important advantages over close-wound system: memory and coil chips are separate and interchangeable; interconnections in coil level are eliminated by packing memory chip and electronics in single structure; and coil size can be adjusted to optimum value in terms of power dissipation and field uniformity.
Chen, T. T.↗
Magnetic bearing
A magnetic bearing is described which includes a pair of coaxial, toroidal, and permanent magnets having axially directed poles. Like poles of the permanent magnets are adjacent to each other, whereby the permanent magnets have a tendency to be urged apart along the common axis. An electromagnet is wound coaxially with the permanent magnets in such a manner that the poles are axially directed. Between the poles of each permanent magnet there is a low magnetic reluctance circuit including two series air gaps. Between the poles of the electromagnet a low reluctance path including only one air gap of each of the low magnetic reluctance circuits is provided. The low reluctance path for the electromagnet includes a ring axially translatable relative to the permanent magnets. The ring forms opposite faces of the air gaps in the magnetic circuits for each permanent magnet.
Studer, P. A.↗
Metal temperatures and coolant flow in a wire cloth transpiration cooled turbine vane
An experimental heat transfer investigation was conducted on an air-cooled turbine vane made from wire-wound cloth material and supported by a central strut. Vane temperature data obtained are compared with temperature data from two full-coverage film-cooled vanes made of different laminated construction. Measured porous-airfoil temperatures are compared with predicted temperatures.
Gladden, H. J.↗
Performance characteristics of the U.VA. superconducting wind tunnel balance
Initial operational characteristics of a wind tunnel electromagnetic balance utilizing superconducting coils are reported. Both dc and ac superconducting coils are used for balancing and measuring 3-component aerodynamic forces on simple models in Mach 3, room temperature flow. Liquid helium boil-off measurements corresponding to a wide range of operating conditions are presented together with results of systematic ac losses scaling experiments using various pancake coils wound with superconducting tape. This unique prototype facility is primarily for studying the practical feasibility of using superconducting magnetic suspension techniques for aerodynamic testing and accumulating the knowledge and expertise required for extrapolating these techniques to large-scale facilities.
Humphris, R. R.↗
High-performance vessels from an aromatic polyamide fiber/epoxy composite
The investigation reported is concerned with the development of a filament-wound, ultralightweight composite vessel for the containment of cryogenic propellants and pressurant gases. The vessels are to be used within an operational temperature range from -253 C to ambient temperature. The fiber used for the process is Kevlar 49. The design and the fabrication of specimens and vessels are discussed along with the results obtained in a testing program.
Chiao, T. T.↗
Toroidal converter core
Improved approach consists of cut and uncut cores nested in concentric configuration. Cores are made by winding steel ribbon on mandrel and impregnating with epoxy to bond layers together. Gap is made by cutting across wound and bonded core. Rough ends are ground or lapped.
Mclyman, W. T.↗
Transformer design tradeoffs
Technical memorandum includes transformer area product numbers, which are used to summarize dimensional and electrical properties of C-cores, pot cores, lamination, powder cores, and tape-wound cores. To aid in core selection, comparison of five common core materials is presented to indicate their influence on overall transformer efficiency and weight.
Mclyman, W. T.↗
Technological development of high energy density capacitors
A study was conducted to develop cylindrical wound metallized film capacitors rated 2 micron F 500 VDC that had energy densities greater than 0.1J/g. Polysulfone (PS) and polyvinylidene (PVF2) were selected as dielectrics. Single film PS capacitors of 0.2J/g (uncased) were made of 3.75 micron material. Single film PVF2 capacitors of 0.19J/g (uncased) were made of 6.0 micron material. Corona measurements were made at room temperature, and capacitance and dissipation factor measurements were made over the ranges 25 C to 125 C and 120 Hz to 100 kHz. Nineteen of twenty PVF2 components survived a 2500 hour dc plus ac life test. Failure analyses revealed most failures occurred at wrinkles, but some edge failures were also seen. A 0.989g case was designed. When the case was combined with the PVF2 component, a finished energy density of 0.11J/g was achieved.
Parker, R. D.↗
Solar energy trap
An apparatus is described for trapping solar energy for heating a fluid that could be subsequently used in turbines and similar devices. The apparatus includes an elongated vertical light pipe having an open end through which the visible spectrum of electromagnetic radiation from the sun passes to strike a tubular absorber. The light pipe has a coated interior surface of a low absorptivity and a high reflectivity at the visible wavelengths and a high absorptivity/emissivity ratio at infrared wavelengths. The tubular absorber has a coating on the surface for absorbing visible wavelengths to heat the fluid passing through. Infrared wave lengths are radiated from the tubular absorber back into the light pipe for heating fluid passing through a tubular coil wound around it.
Brantley, L. W., Jr.↗
Investigation of a quadrupole ultra-high vacuum ion pump
The new nonmagnetic ion pump resembles the quadrupole ionization gage. The dimensions are larger, and hyperbolically shaped electrodes replace the four rods. Their surfaces follow y sq. = 36 + x sq. (x, y in centimeters). The electrodes, 55 cm long, are positioned lengthwise in a tube. At one end a cathode emits electrons; at the other end a narrowly wound flat spiral of tungsten clad with titanium on cathode potential can be heated for titanium evaporation. Electrons accelerated by a dc potential of the surface electrodes oscillate between the ends on rotational trajectories, if a high frequency potential superimposed on the dc potential is properly adjusted. Pumping speeds (4-100 liter/sec) for different gases at different peak voltages (1000-3000V) at corresponding frequencies (57-100 MHz), and at different pressures 0.00001 to the minus 9 power Torr were observed. The lowest pressure reached was below 10 to the minus 10 power Torr.
Schwarz, H. J.↗
Fatigue performance of metal-lined graphite/epoxy pressure vessels
Using an ultrahigh-strength graphite fiber, a program was started to develop a thin metal-lined fiber/epoxy pressure vessel that would have a fatigue life of over 1000 cycles. First, the performance factor of the fiber/epoxy composite was found to be 351 kN m/kg from the average of 18 rubber-lined pressure vessels. Then, both aluminum- and titanium-lined vessels were filament wound with the graphite fiber in an epoxy matrix. Several of these metal-lined vessels were subjected to hydraulic fatigue testing to about 50% of their expected burst pressures. The average fatigue life of the aluminum-lined vessels was 462 cycles; the average for the titanium-lined vessels was 2190 cycles.
Hamstad, M. A.↗
The origin of the nonthermal radiation of quasi-stellar objects and galactic nuclei
The supermassive-star model for the origin of the nonthermal luminosity of quasars and nuclei of Seyfert galaxies is analyzed. In the general model, a moving magnetic field is the accelerating mechanism for ultrarelativistic particles and gravitational collapse is the energy source. Several specific models are considered for the magnetic field, including a frozen-in field that is twisted about the axis of a rotating supermassive star, a tightly wound magnetic spiral, and the rotating field of a giant pulsar. In the general model, an accelerating efficiency close to unity is assumed. However, it is found that observational and theoretical evidence indicate an accelerating efficiency of less than 0.01 for the specific magnetic-field models. Mass-loss rates of quasars and Seyfert nuclei are calculated on the basis of the lower efficiency value and found to be reasonable.
Opher, R.↗
Superconductor coil geometry and ac losses
An empirical relation is presented which allows simple computation of volume-averaged winding fields from central fields for coils of small rectangular cross sections. This relation suggests that, in certain applications, ac-loss minimization can be accomplished by use of low winding densities, provided that hysteresis losses are independent of winding density. The ac-loss measurements on coils wound of twisted multifilamentary composite superconductors show no significant dependence on ac losses on winding density, thus permitting the use of winding density as an independent design parameter in loss minimization.
Pierce, T. V., Jr.↗
Design study of steady-state 30-tesla liquid-neon-cooled magnet
A design for a 30-tesla, liquid-neon-cooled magnet was reported which is capable of continuous operation. Cooled by nonboiling, forced-convection heat transfer to liquid neon flowing at 2.8 cu m/min in a closed, pressurized heat-transfer loop and structurally supported by a tapered structural ribbon, the tape-wound coils with a high-purity-aluminum conductor will produce over 30 teslas for 1 minute at 850 kilowatts. The magnet will have an inside diameter of 7.5 centimeters and an outside diameter of 54 centimeters. The minimum current density at design field will be 15.7 kA/sq cm.
Prok, G. M.↗
Microwave power tubes for space applications
Feasibility evaluations of klystron amplifiers for conversion of solar power in synchronous orbit into microwave power at 2.4 GHz and transmission to earth were carried out. It was found that amplitrons and klystrons, using a depressed collector augmentation, can achieve efficiencies in excess of 80% if the power output is kept higher than 50 kW. Body wound selenoid provides the needed beam-focusing field. Narrow bandwidth requirements permit a low cathode loading density of 0.5 A/sq cm produced at approximately 850 centigrades. Emission tests indicate a potential life expectancy of 20 to 40 years.
Kosmahl, H.↗
Reel safety brake
A braking apparatus is described for a tape transport device having two stacked coaxial reels and feelers mounted in proximity to the reels for sensing the tape being wound on each reel. A device is mounted in proximity to adjacent central hubs of the reels to a simultaneously, frictionally engage both hubs and brake both reels. A mechanical actuator is coupled to both feelers and to the brake device. The brake means comprises a pair of rubber shoulders that extend in opposite directions relative to a common axis, and turns about the axis in response to either of the feelers.
Carle, C. E.↗
Spring operated accelerator and constant force spring mechanism therefor
A spring assembly consisting of an elongate piece of flat spring material formed into a spiral configuration and a free running spool in circumscribing relation to which this spring is disposed was developed. The spring has a distal end that is externally accessible so that when the distal end is drawn along a path, the spring unwinds against a restoring force present in the portion of the spring that resides in a transition region between a relatively straight condition on the path and a fully wound condition on the spool. When the distal end is released, the distal end is accelerated toward the spool by the force existing at the transition region which force is proportional to the cross-sectional area of the spring.
Shillinger, G. L., Jr.↗