Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “WELDING, ARC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

A Fast and Accurate Reduced-Order Model for High-Intensity Transferred Arc Discharges

Arc discharges are widely used in welding, plasma smelting, and other industrial processes, where variations in operating conditions strongly affect arc stability, temperature distribution, and energy transfer. Accurate modeling of these phenomena typically requires computationally expensive high-fidelity simulations. This study presents a hierarchy of three arc discharge models with progressively reduced physical fidelity. The high-fidelity model provides a fully physics-resolved reference, the reduced-order model reproduces the dominant thermal and flow characteristics of the arc with reasonable accuracy, and the Elenbaas-Heller model captures key trends in a simplified, rapid formulation. This hierarchy demonstrates that reduced-order model can effectively balance predictive fidelity and computational efficiency, providing practical tools for arc simulation and parametric studies.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1974

Crack-growth behavior in thick welded plates of Inconel 718 at room and cryogenic temperatures

Results of mechanical-properties and axial-load fatigue and fracture tests performed on thick welded plates of Inconel 718 superalloy are presented. The test objectives were to determine the tensile strength properties and the crack-growth behavior in electron-beam, plasma-arc, and gas tungsten are welds for plates 1.90 cm (0.75 in) thick. Base-metal specimens were also tested to determine the flaw-growth behavior. The tests were performed in room-temperature-air and liquid nitrogen environments. The experimental crack-growth-rate data are correlated with theoretical crack-growth-rate predictions for semielliptical surface flaws.

Forman, R. G.↗
NASA NTRS1971

Dye penetrant indications caused by superficial surface defects in 2014 aluminum alloy welds.

Demonstration that dye penetrant indications on the heat-affected zone of 2014-T6 aluminum GMA weldments are frequently caused by superficial surface conditions and are less than 0.007 in. deep. The following methods are suggested for minimization of these surface defects: stabilization of the arc, application of dc ?GTA' welding procedures, reduction of the caustic etch time, and use of fine grain materials.

Hocker, R. G.↗
NASA NTRS1986

Program for Heat Flow in Welding

Program contains numerical model of temperature distribution in vicinity of weld. Weld model used to produce estimated welding power requirements, welding-power-loss analysis, heat-affected-zone temperature history, and weld-puddle cross-section plots. Applied to gas/tungsten-arc, plasma-arc, electron-beam, and laser-beam welds on wide plates under steady conditions. User predicts power requirements and temperature distributions. Weld model written in BASIC.

Nunes, A. C., Jr.↗
NASA NTRS2008

Thermal Stir Welding Development at Marshall Space Flight Center

Solid state welding processes have become the focus of welding process development at NASA's Marshall Space Flight Center. Unlike fusion weld processes such as tungsten inert gas (TIG), variable polarity plasma arc (VPPA), electron beam (EB), etc., solid state welding processes do not melt the material during welding. The resultant microstructure can be characterized as a dynamically recrystallized morphology much different than the casted, dentritic structure typical of fusion weld processes. The primary benefits of solid state processes over fusion weld processes include superior mechanic properties and the elimination of thermal distortion and residual stresses. These solid state processes attributes have profoundly influenced the direction of advanced welding research and development within the NASA agency. Thermal Stir Welding (TSW) is a new solid state welding process being developed at the Marshall Space Flight Center. Unlike friction stir welding, the heating, stirring and forging elements of the weld process can be decoupled for independent control. An induction coil induces energy into a workpiece to attain a desired plastic temperature. An independently controlled stir rod, captured within non-rotating containment plates, then stirs the plasticized material followed by forging plates/rollers that work the stirred weld joint. The independent control (decoupling) of heating, stirring and forging allows, theoretically, for the precision control of microstructure morphology. The TSW process is being used to evaluate the solid state joining of Haynes 230 for ARES J-2X applications. It is also being developed for 500-in (12.5 mm) thick commercially pure grade 2 titanium for navy applications. Other interests include Inconel 718 and stainless steel. This presentation will provide metallurgical and mechanical property data for these high melting temperature alloys.

Ding, Robert J.↗
NASA NTRS1976

Computerized adaptive control weld skate with CCTV weld guidance project

This report summarizes progress of the automatic computerized weld skate development portion of the Computerized Weld Skate with Closed Circuit Television (CCTV) Arc Guidance Project. The main goal of the project is to develop an automatic welding skate demonstration model equipped with CCTV weld guidance. The three main goals of the overall project are to: (1) develop a demonstration model computerized weld skate system, (2) develop a demonstration model automatic CCTV guidance system, and (3) integrate the two systems into a demonstration model of computerized weld skate with CCTV weld guidance for welding contoured parts.

Wall, W. A.↗
DOE OSTI2011

Modeling Arcs

Although vacuum arcs were first identified over 110 years ago, they are not yet well understood. We have since developed a model of breakdown and gradient limits that tries to explain, in a self-consistent way: arc triggering, plasma initiation, plasma evolution, surface damage and gradient limits. We use simple PIC codes for modeling plasmas, molecular dynamics for modeling surface breakdown, and surface damage, and mesoscale surface thermodynamics and finite element electrostatic codes for to evaluate surface properties. Since any given experiment seems to have more variables than data points, we have tried to consider a wide variety of arcing (rf structures, e beam welding, laser ablation, etc.) to help constrain the problem, and concentrate on common mechanisms. While the mechanisms can be comparatively simple, modeling can be challenging.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2019

SS410 Process Development and Characterization

Wire-fed stainless-steel additive manufacturing provides the potential for an alternative to traditional stainless-steel tool making processes. 410 stainless steel provides the necessary hardness for long term tool use and its corrosion resistances negates the need for post processing of non-critical faces. 410 has unique characteristics that require different design and welding parameters from other materials. This paper will look at the parameters and characteristics to expect when using wire-arc deposition for 410 stainless steel. Individual weld beads and simple geometric features were printed using the mBAAM wire-arc system at ORNL to determine effective wire-arc parameters for SS410. Once parameters were chosen, additional features were printed to determine the geometric characteristics of printed SS410 as well as compare the differences between designed geometries and printed geometries. These results allow for the formulation of smarter design rules when designing parts for SS410 additive manufacturing.

Vaughan, Derek↗
NASA NTRS1966

Power arc welder touch-started with consumable electrode

Power arc welder formed as a hand-held welding gun touch-starts, retracts a consumable electrode to create the desired arc, and then commences feeding of the consumable electrode at the rate required to form the intended bead or spot. This device achieves uniform spot welds repeatedly.

Jeannette, J. C.↗
NASA NTRS1982

Automatic Welding System

Robotic welding has been of interest to industrial firms because it offers higher productivity at lower cost than manual welding. There are some systems with automated arc guidance available, but they have disadvantages, such as limitations on types of materials or types of seams that can be welded; susceptibility to stray electrical signals; restricted field of view; or tendency to contaminate the weld seam. Wanting to overcome these disadvantages, Marshall Space Flight Center, aided by Hayes International Corporation, developed system that uses closed-circuit TV signals for automatic guidance of the welding torch. NASA granted license to Combined Technologies, Inc. for commercial application of the technology. They developed a refined and improved arc guidance system. CTI in turn, licensed the Merrick Corporation, also of Nashville, for marketing and manufacturing of the new system, called the CT2 Optical Trucker. CT2 is a non-contracting system that offers adaptability to broader range of welding jobs and provides greater reliability in high speed operation. It is extremely accurate and can travel at high speed of up to 150 inches per minute.

Source record↗
NASA NTRS2006

Heat Treatment of Friction-Stir-Welded 7050 Aluminum Plates

A method of heat treatment has been developed to reverse some of the deleterious effects of friction stir welding of plates of aluminum alloy 7050. This alloy is considered unweldable by arc and high-energy-density beam fusion welding processes. The alloy can be friction stir welded, but as-welded workpieces exhibit low ductility, low tensile and yield strengths, and low resistance to stress corrosion cracking. Heat treatment according to the present method increases tensile and yield strengths, and minimizes or eliminates stress corrosion cracking. It also increases ductility. This method of heat treatment is a superior alternative to a specification-required heat treatment that caused the formation of large columnar grains, which are undesired. Workpieces subjected to the prior heat treatment exhibited elongations <2 percent, and standard three-point bend specimens shattered. The development of the present heat treatment method was guided partly by the principles that (1) by minimizing grain sizes and relieving deformation stresses, one can minimize or eliminate stress corrosion cracking and (2) the key to maximizing strength and eliminating residual stresses is to perform post-weld solution heating for as long a time as possible while incurring little or no development of large columnar grains in friction stir weld nuggets. It is necessary to perform some of the solution heat treatment (to soften the alloy and improve machine welding parameters) before welding. The following is an example of thickness- dependent pre- and post-weld heat treatments according to the present method: For plates 0.270 in. (approx.6.86 mm) thick milled from plates 4.5 in. (114.3 mm) thick, perform pre-weld solution heating at 890 F (477 C) for 1 hour, then cool in air. After friction stir welding, perform solution heating for 10 minutes, quench, hold at room temperature for 96 hours, then age at 250 F (121 C) for 5 hours followed by 325 F (163 C) for 27 hours.

Petter, George E.↗
DOE OSTI2020

Wire-Based Additive Manufacturing of Stainless Steel Components

In this work three different wire-fed additive manufacturing (AM) processes were employed to evaluate differences between laser, arc, and electron beam heat sources used for high-deposition-rate AM on the order of 1 kg/h. Optimum weld and build parameters were developed independently to match the characteristics of each heat source using 308L stainless steel welding wire as the feedstock. Laser-wire AM was made with the lowest energy per unit length of weld and had the best control of the melt pool and surface finish. Wire arc-based AM had an intermediate energy per unit length of weld of approximately 5× that of the laser process, while electron beam wire AM had the highest energy per unit length of weld at approximately 10× that of the laser process. Analysis of the parts that were built included evaluation of mechanical properties and microstructures, and these properties are discussed with respect to the difference in input energy and cooling rates. Results show that all three processes build parts with properties that exceed those of annealed 304L wrought stainless steel. However, significant differences exist between the processes, and the results presented here can be used to help select the best wire-fed process for a given high-deposition-rate application.

36 MATERIALS SCIENCE↗
NASA NTRS1999

Weld Pool Stability in the Flat Position

The Soft Plasma Arc (SPA) process was devised to avoid interactions between backshield and full penetration mode plasma jet in welding 2195 aluminum-lithium alloy. Occasional sudden and mysterious losses in penetration were encountered in flat position SPA welding. To understand what was happening a model of the dynamics of the molten metal meniscus at the root of the weld was worked out. When the power input to the weld P(sub in) exceeds the power leakage P(sub out) the difference in power is absorbed by an increase in the molten weld pool volume V, Rho X L(SUB m) X (d(V)/dt)) = P(sub in) - P(sub out) where rho is the density and L(sub m) the specific heat of the weld metal.

Nunes, A. C., Jr.↗
DOE OSTI2012

Sr{sub 7}Ge{sub 6}, Ba{sub 7}Ge{sub 6} and Ba{sub 3}Sn{sub 2} -Three new binary compounds containing dumbbells and four-membered chains of tetrel atoms with considerable Ge-Ge {pi}-bonding character

The germanides Sr{sub 7}Ge{sub 6} and Ba{sub 7}Ge{sub 6} as well as the stannide Ba{sub 3}Sn{sub 2} were prepared by arc melting and annealing in welded tantalum ampoules using induction as well as resistance furnaces. The compounds were investigated by powder and single crystal X-ray diffraction. Sr{sub 7}Ge{sub 6} and Ba{sub 7}Ge{sub 6} crystallize in the Ca{sub 7}Sn{sub 6} structure type (space group Pmna, Z=4: a=7.777(2) A, b=23.595(4) A, c=8.563(2) A, wR{sub 2}=0.081 (all data), 2175 independent reflections, 64 variable parameters for Sr{sub 7}Ge{sub 6} and a=8.0853(6) A, b=24.545(2) A, c=8.9782(8) A, wR{sub 2}=0.085 (all data), 2307 independent reflections, 64 variable parameters for Ba{sub 7}Ge{sub 6}). Ba{sub 3}Sn{sub 2} crystallizes in an own structure type with the space group P4{sub 3}2{sub 1}2, Z=4, a=6.6854(2) A, c=17.842(2) A, wR{sub 2}=0.037 (all data), 1163 independent reflections, 25 variable parameters. In Sr{sub 7}Ge{sub 6} and Ba{sub 7}Ge{sub 6} the Ge atoms are arranged as Ge{sub 2} dumbbells and Ge{sub 4} four-membered atom chains. Their crystal structures cannot be rationalized according to the (8-N) rule. In contrast, Ba{sub 3}Sn{sub 2} presents Sn{sub 2} dumbbells as a main structural motif and thereby can be described as an electron precise Zintl phase. The chemical bonding situation in these structures is discussed on the basis of partial and total Density Of States (DOS) curves, band structures including fatbands, topological analysis of the Electron Localization Function (ELF) as well as Bader analysis of the bond critical points using the programs TB-LMTO-ASA and WIEN2K. While Ba{sub 3}Sn{sub 2} reveals semiconducting behaviour, all germanides Ae{sub 7}Ge{sub 6} (Ae=Ca, Sr, and Ba) show metallic properties and a considerable {pi}-bonding character between the Ge atoms of the four-membered chains and the dumbbells. The {pi}-bonding character of the germanides is best reflected by the resonance hybrid structures {l_brace}[Ge-Ge]{sup 6-}/[Ge-{sup ....}Ge-{sup ....}Ge-{sup ....}Ge]{sup 8-}{r_brace}{r_reversible}{l_brace}[Ge=Ge]{sup 4-}/[Ge-Ge-Ge-Ge]{sup 10-}{r_brace}. - Graphical abstract: The structure of Ba{sub 3}Sn{sub 2} contains Sn{sub 2} dumbbells as a main structural motif and thereby can be described as an electron precise Zintl phase. Ge{sub 2} dumbbells and Ge{sub 4} four-membered atom chains are the predominant features in Sr{sub 7}Ge{sub 6} and Ba{sub 7}Ge{sub 6}. Their crystal structures cannot be rationalized according to the (8-N) rule. While Ba{sub 3}Sn{sub 2} reveals semiconducting behaviour, the germanides Ae{sub 7}Ge{sub 6} (Ae=Ca, Sr, and Ba) show metallic properties and a considerable {pi}-bonding character between the Ge atoms of the four-membered chains and the dumbbells. Highlights: Black-Right-Pointing-Pointer The germanides Sr{sub 7}Ge{sub 6} and Ba{sub 7}Ge{sub 6} as well as the stannide Ba{sub 3}Sn{sub 2} have been synthesized. Black-Right-Pointing-Pointer In Sr{sub 7}Ge{sub 6} and Ba{sub 7}Ge{sub 6} the Ge atoms are arranged as dumbbells and four-membered atom chains. Black-Right-Pointing-Pointer Ba{sub 3}Sn{sub 2} presents Sn{sub 2} dumbbells as a main structural motif. Black-Right-Pointing-Pointer The chemical bonding situation within these structures is discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2012

PDC IC Weld Failure Evaluation and Resolution

During final preparations for start of the PDCF Inner Can (IC) qualification effort, welding was performed on an automated weld system known as the PICN. During the initial weld, using a pedigree canister and plug, a weld defect was observed. The defect resulted in a hole in the sidewall of the canister, and it was observed that the plug sidewall had not been consumed. This was a new type of failure not seen during development and production of legacy Bagless Transfer Cans (FB-Line/Hanford). Therefore, a team was assembled to determine the root cause and to determine if the process could be improved. After several brain storming sessions (MS and T, R and D Engineering, PDC Project), an evaluation matrix was established to direct this effort. The matrix identified numerous activities that could be taken and then prioritized those activities. This effort was limited by both time and resources (the number of canisters and plugs available for testing was limited). A discovery process was initiated to evaluate the Vendor's IC fabrication process relative to legacy processes. There were no significant findings, however, some information regarding forging/anneal processes could not be obtained. Evaluations were conducted to compare mechanical properties of the PDC canisters relative to the legacy canisters. Some differences were identified, but mechanical properties were determined to be consistent with legacy materials. A number of process changes were also evaluated. A heat treatment procedure was established that could reduce the magnetic characteristics to levels similar to the legacy materials. An in-situ arc annealing process was developed that resulted in improved weld characteristics for test articles. Also several tack welds configurations were addressed, it was found that increasing the number of tack welds (and changing the sequence) resulted in decreased can to plug gaps and a more stable weld for test articles. Incorporating all of the process improvements for the actual can welding process, however, did not result in an improved weld geometry. Several possibilities for the lack of positive response exist, some of which are that (1) an insufficient number of test articles were welded under prototypic conditions, (2) the process was not optimized so that significant improvements were observable over the "noise", and (3) the in-situ arc anneal closed the gap down too much so the can was unable to exhaust pressure ahead of the weld. Several operational and mechanical improvements were identified. The weld clamps were changed to a design consistent with those used in the legacy operations. A helium puff operation was eliminated; it is believed that this operation was the cause of the original weld defect. Also, timing of plug mast movement was found to correspond with weld irregularities. The timing of the movement was changed to occur during weld head travel between tacks. In the end a three sequential tack weld process followed by a pulse weld at the same current and travel speed as was used for the legacy processes was suggested for use during the IC qualification effort. Relative to legacy welds, the PDC IC weld demonstrates greater fluctuation in the region of the weld located between tack welds. However, canister weld response (canister to canister) is consistent and with the aid of the optical mapping system (for targeting the cut position) is considered adequate. DR measurements and METs show the PDC IC welds to have sufficient ligament length to ensure adequate canister pressure/impact capacity and to ensure adequate stub function. The PDC welding process has not been optimized as a result of this effort. Differences remain between the legacy BTC welds and the PDC IC weld, but these differences are not sufficient to prevent resumption of the current PDC IC qualification effort. During the PDC IC qualification effort, a total of 17 cans will be welded and a variety of tests/inspections will be performed. The extensive data collected during that qualification effort should be of a sufficient population to determine if additional weld process optimization is necessary prior to production release.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRS1972

Extended electrode technique

The extended electrode technique is a unique welding process which utilizes manual gas-metal-arc (GMAW) semi-automatic equipment and close, square butt joints to effectively produce a weld. The technique takes advantage of the resistance heating of the electode extension to effect the root pass. Weldments as large as 72-X30-X2-inch have been fabricated with this technique under normal shipyard welding conditions. Mechanical properties and explosion bulge tests indicate that satisfactory results are obtained with this process. Potential savings of approximately 50 percent can be achieved in flat welding and repair of heavy structural steel members.

Schaper, V. D.↗
DOE OSTI2014

Creep and Creep-Fatigue of Alloy 617 Weldments

Alloy 617 is the primary candidate material for the heat exchanger of a very high temperature gas cooled reactor intended to operate up to 950°C. While this alloy is currently qualified in the ASME Boiler and Pressure Vessel Code for non-nuclear construction, it is not currently allowed for use in nuclear designs. A draft Code Case to qualify Alloy 617 for nuclear pressure boundary applications was submitted in 1992, but was withdrawn prior to approval. Prior to withdrawal of the draft, comments were received indicating that there was insufficient knowledge of the creep and creep-fatigue behavior of Alloy 617 welds. In this report the results of recent experiments and analysis of the creep-rupture behavior of Alloy 617 welds prepared using the gas tungsten arc process with Alloy 617 filler wire. Low cycle fatigue and creep-fatigue properties of weldments are also discussed. The experiments cover a range of temperatures from 750 to 1000°C to support development of a new Code Case to qualify the material for elevated temperature nuclear design. Properties of the welded material are compared to results of extensive characterization of solution annealed plate base metal.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

ADDITIVE MANUFACTURING AND REGULATORY TESTING OF CANISTERS FOR SPENT NUCLEAR FUEL MANAGEMENT

The back end of the fuel cycle focuses on the interim storage, transportation, and final disposition of the spent nuclear fuel from nuclear reactors. Commercial light water nuclear power stations across the United States operate with fuel assemblies being irradiated for up to 6 years (planned) in the reactor pressure vessel. After their planned irradiation, the fuel assemblies are moved to a spent fuel pool within the facility complex. After the spent nuclear fuel is removed from the fuel pool, it is typically inserted into a welded metal canister that can be transferred between overpacks for storage, transportation and possibly disposal. Most dry storage systems being used by industry today use dual purpose canisters (DPCs), designed for use in storage and transportation overpacks, but not specifically designed for disposal. Triple purpose-canisters, designed for disposal in addition to storage and transportation, have also been researched. Traditional manufacturing methods for spent fuel canisters involve fusion welding along the length or circumference of the canister which results in high tensile residual stresses in the joint weld zone (WZ) and heat affected zone (HAZ). In this paper, spent fuel canister designs were printed by wire arc additive manufacturing (AM) using the 316L SS welding wire to demonstrate: 1. Feasibility of spent nuclear fuel canister fabrication using this advanced manufacturing method, 2. Dynamic response of the additive manufacture canister design when subjected to the federally mandated Normal Conditions of Transport (NCT) and Hypothetical Accident Conditions (HAC) physical tests for Type B packages. This paper will focus on the canister printing design and structural tests. The AM 3D printed design, regulatory testing, and post-test evaluation of the canister tested to the 10 CFR 71.71 and 10 CFR 71.73 requirements will be presented. One AM canister design was subjected to the penetration, free drop, and puncture test. Before and after the dynamic structural tests, the AM canister design was scanned with a handheld scanner to capture a 3D CAD geometry to compare to the 3D printed canister design in the deformed shape. The scanned geometry was sectioned in areas with deformation and the cross-section profile was measured to determine accurate and repeated results of the deformed shape of the AM canister design.

Martinez, Oscar↗