Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Tipping Point”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Energy efficient engine. Fan and quarter-stage component performance report

The fan configuration for the general Electric/NASA Energy Efficient Engine was selected following an extensive preliminary design study. The fan has an inlet radius ratio of 0.342 and a specific flowrate of 208.9 Kg/sec/sq. m (42.8 1bm/sec/sq. ft). The design corrected tip speed is 411.5 m/sec (1350 ft/sec) producing a bypass flow total-pressure ratio of 1.65 and a core flow total-pressure ratio of 1.6. The design bypass ratio is 6.8. The aerodynamic design point corresponds to the maximum climb power setting at Mach 0.8 and 10.67 Km (35,000 ft) altitude. The fully-instrumented fan component was tested in the Lynn Large Fan Test Facility in 1981. The overall performance results, reported herein, showed excellent fan performance with the fan meeting all of its component test goals of flow, efficiency and stall margin.

Cline, S. J.↗
NASA NTRS1985

Shear-lag analysis of notched laminates with interlaminar debonding

The fracture behavior of a debonded zone of finite width with no longitudinal damage in the unidirectional ply is predicted and the solution is then extended to include longitudinal matrix yielding and splitting in the unidirectional ply at the crack tip. The shear-lag assumption is used to describe the shear transfer between fibers. The fracture behavior of the laminate is studied as a function of initial crack length, constraint ratio, and width of the debonded zone. Results indicate that debonding can reduce the maximum fiber stress at the crack tip on the order of ten percent. This effect is maximum for a debonded width of two or three fiber spacings and is independent of the initial crack length. As the debond width grows beyond this point, the maximum stress increases. For widths of about ten fiber spacings or more, the maximum fiber stress is larger than for the fully bonded case. In the presence of longitudinal matrix damage the same general behavior is found; however, the location of the maximum fiber stress is quite complex.

Kaw, A. K.↗
NASA NTRS1992

Effect of upstream disturbance on flow asymmetry

Results are presented of an experimental study aimed at revealing the origin of the asymmetric mean flow that occurs on pointed bodies of revolution at moderate-to-high angles of attack. The placement of a small fixed disturbance (a minute spherical bead) on a very thin wire at various locations in the flow near the tip of the model is shown to provoke the same range of behavior of the asymmetric flow that was produced earlier by use of a controlled retractable wire protuberance, here without touching or altering the tip at all. Results remain consistent with the presence of a convective instability mechanism, and demonstrate the potential for a precise mapping of the body's receptivity to fixed disturbances in the flowfield.

Degani, David↗
NASA NTRS1994

Buckling of composite beams (CDDF)

Presented are the results of an investigation of the twisting/warping deformation occurring in open-section composite beams. A series of C and L channels were manufactured using both hand layup and the innovative 'hot-drape forming' techniques. A transverse tip load was applied at the free end of the cantilevered open-section beams. The test setup allowed the tip load to be applied at various locations along the plane of and at the beam's shear center. Charts are included in this report depicting various angles of ply layups, loads applied, and load application points. A major verification resulting from this study is that the shear center of an open section composite beam can be altered, if not completely controlled, through laminate layup. Also, it was observed that the choice of the material system does not have an effect on the amount of deformation, as expected, and the material affects the location of an unsymmetric open section composite beam's true shear center. The results from this study have provided a foundation for further investigation into the apparent shifting of the shear center location in open-section composite beams.

Thompson, P.↗
NASA NTRS2010

Method for nanoscale spatial registration of scanning probes with substrates and surfaces

Embodiments in accordance with the present invention relate to methods and apparatuses for aligning a scanning probe used to pattern a substrate, by comparing the position of the probe to a reference location or spot on the substrate. A first light beam is focused on a surface of the substrate as a spatial reference point. A second light beam then illuminates the scanning probe being used for patterning. An optical microscope images both the focused light beam, and a diffraction pattern, shadow, or light backscattered by the illuminated scanning probe tip of a scanning probe microscope (SPM), which is typically the tip of the scanning probe on an atomic force microscope (AFM). Alignment of the scanning probe tip relative to the mark is then determined by visual observation of the microscope image. This alignment process may be repeated to allow for modification or changing of the scanning probe microscope tip.

Wade, Lawrence A.↗
NASA NTRS1992

Crustal deformation measurements in central Japan determined by a Global Positioning System fixed-point network

Results are presented from temporally dense measurements of crustal deformation associated with the convergence of the Eurasian (EUR), Pacific, North American, and Philippine Sea (PHS) plates, carried out in April 1988 by a 10-station GPS fixed-point network established in central Japan. Using regional orbit relaxation methods, the analysis of the first 17-month data revealed significant horizontal deformation across the Suruga trough. Namely, it was found that a site in the northern tip of PHS plate moved nearly westward with a velocity of 28 +/-5 mm per year, and a site at the southeastern tip of EUR plate moved south-southwestward with a velocity of 18 +/-5 mm per year. A significant vertical uplift with a velocity of 20 mm/yr was detected at a site inland of the Tokai district located in the Akaishi uplift zone and at a site on the Hatsushima Island in Sagami Bay.

Shimada, Seiichi↗
NASA NTRS1993

Navier-Stokes simulation of rotor-body flowfield in hover using overset grids

A free-wake Navier-Stokes numerical scheme and multiple Chimera overset grids have been utilized for calculating the quasi-steady hovering flowfield of a Boeing-360 rotor mounted on an axisymmetric whirl-tower. The entire geometry of this rotor-body configuration is gridded-up with eleven different overset grids. The composite grid has 1.3 million grid points for the entire flow domain. The numerical results, obtained using coarse grids and a rigid rotor assumption, show a thrust value that is within 5% of the experimental value at a flow condition of M(sub tip) = 0.63, Theta(sub c) = 8 deg, and Re = 2.5 x 10(exp 6). The numerical method thus demonstrates the feasibility of using a multi-block scheme for calculating the flowfields of complex configurations consisting of rotating and non-rotating components.

Srinivasan, G. R.↗
NASA NTRS1978

Gas Path Sealing in Turbine Engines

A survey of gas path seals is presented with particular attention given to sealing clearance effects on engine component efficiency. The effects on compressor pressure ratio and stall margin are pointed out. Various case-rotor relative displacements, which affect gas path seal clearances, are identified. Forces produced by nonuniform sealing clearances and their effect on rotor stability are discussed qualitatively, and recent work on turbine-blade-tip sealing for high temperature is described. The need for active clearance control and for engine structural analysis is discussed. The functions of the internal-flow system and its seals are reviewed.

Ludwig, L. P.↗
NASA NTRS1978

Gas path sealing in turbine engines

Survey of gas path seals is presented with particular attention given to sealing clearance effects on engine component efficiency. The effects on compressor pressure ratio and stall margin are pointed out. Various case-rotor relative displacements, which affect gas path seal clearances, are identified. Forces produced by nonuniform sealing clearances and their effect on rotor stability are discussed qualitatively, and recent work on turbine-blade-tip sealing for high temperatures is described. The need for active clearance control and for engine structural analysis is discussed. The functions of the internal-flow system and its seals are reviewed.

Ludwig, L. P.↗
NASA NTRS1980

Aerodynamic performances of three fan stator designs operating with rotor having tip speed of 337 meters per second and pressure ratio of 1.54. 1: Experimental performance

The aerodynamic performances of four stator-blade rows are presented and evaluated. The aerodynamic designs of two of these stators were compromised to reduce noise, a third design was not. On a calculated operating line passing through the design point pressure ratio, the best stator had overall pressure-ratio and efficiency decrements of 0.031 and 0.044, respectively, providing a stage pressure ratio of 1.483 and efficiency of 0.865. The other stators showed some correctable deficiencies due partly to the design compromises for noise. In the end-wall regions blade-element losses were significantly less for the shortest chord studied.

Gelder, T. F.↗
DOE OSTI2020

Nanomechanical sampling of material for nanoscale mass spectrometry chemical analysis

The ability to spatially resolve the chemical distribution of compounds on a surface is important in many applications ranging from biological to material science. To this extent, we have recently introduced a hybrid atomic force microscopy (AFM)-mass spectrometry (MS) system for direct thermal desorption and pyrolysis of material with nanoscale chemical resolution. However, spatially resolved direct surface heating using local thermal desorption becomes challenging on material surfaces with low melting points, because the material will undergo a melting phase transition due to heat dissipation prior to onset of thermal desorption. Therefore, here we developed an approach using mechanical sampling and collection of surface materials on an AFM cantilever probe tip for real-time analysis directly from the AFM tip. This approach allows for material to be concentrated directly onto the probe for subsequent MS analysis. We evaluate the performance metrics of the technique and demonstrate localized MS sampling from a candelilla wax matrix containing UV stabilizers avobenzone and oxinoxate from areas down to 250 nm × 250 nm. Overall, this approach removes heat dissipation into the bulk material allowing for a faster desorption and concentration of the gas phase analyte from a single heating pulse enabling higher signal levels from a given amount of material in a single sampling spot.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1989

Computational/experimental study of the flowfield on a body of revolution at incidence

A joint computational-experimental study of the vortical flowfield on a pointed body of revolution is undertaken. The incompressible Navier-Stokes equations are solved numerically for steady flow around an ogive-cylinder at angle of attack. The three-dimensional vortical flow is investigated, with emphasis on the tip and the near-wake region. Comparisons of computational results with results of a companion towing-tank experiment are presented at Re(L) = 1000. Results of a wind tunnel experiment at Re(L) = 820,000, featuring use of a seven-hole pressure probe, also are presented. It was observed that at the low Reynolds number of the towing tank study, the leeside flow was symmetric at the angles of attack considered. For the same configuration at the higher Reynolds number of the wind tunnel study, the flow was asymmetric under equivalenat conditions for some of the angles of attack studied. The topology of the flow is discussed and conclusions are drawn concerning the growth and stability of the primary vortices.

Zilliac, G. G.↗
DOE OSTI2022

Large-Eddy Simulation of a wind turbine using a Filtered Actuator Line Model

When dealing with multirotor devices such as quadcopters or wind farms, the cost of blade-resolved large-eddy simulation (LES) becomes prohibitive. Combining LES with a family of lower-fidelity models, called actuator line models (ALMs), has grown in popularity in the past decade. ALM replaces full blade resolution with an array of actuator points or lines parameterized by aerodynamic lift/drag polar plots along the blades. Body forces computed based on these actuator points are then projected onto the LES flow mesh, mimicking the effect of rotating blades on the flow. However, the optimal projection radius and the associated LES grid size is often too restrictive for multirotor simulations. Recently, a new tip-correction-based filtered ALM (F-ALM) was proposed by Martinez-Tossas and Meneveau (2019), which allows coarser-than-optimal grids by avoiding the associated overprediction of thrust. In this work, F-ALM is implemented into a high-order, in-house LES code to simulate National Renewable Energy Laboratory Phase VI wind turbine. It is then followed by a comparison between the baseline ALM and the newly implemented F-ALM in terms of instantaneous and time-averaged flow fields and blade loads, revealing the advantages of F-ALM in preventing the overprediction of power on coarse grids. Finally, this encourages accurate and affordable simulations of multirotor devices in the future.

17 WIND ENERGY↗
NASA NTRS1977

Calculation of 3-dimensional choking mass flow in turbomachinery with 2-dimensional flow models

An approach is considered for obtaining an approximate flow solution in the case of a cross-sectional flow surface within a guided channel, taking into account a pair of typical turbine blades with three-dimensional orthogonal surfaces across the flow passage, the calculation of the mass flow across the throat in the case of a 2-D passage with curved walls, and the determination of the choking mass flow. It is pointed out that the choking solution for a three-dimensional guided passage in a blade row can be obtained in a very similar manner by satisfying momentum equations for the blade-to-blade and the hub-to-tip direction. A considered example involves the calculation of the choking mass flow for a centrifugal compressor impeller in an automotive application.

Katsanis, T.↗
NASA NTRS1980

Experimental performance and analysis of 15.04-centimeter-tip-diameter, radial-inflow turbine with work factor of 1.126 and thick blading

The aerodynamic design, the performance, and an internal loss breakdown were examined for a 15.04 cm tip diameter, radial-inflow turbine. The design application was to drive a two stage, 10 to 1 pressure ratio compressor with a mass flow of 0.952 kg/sec and a rotative speed of 70,000 rmp. The turbine inlet temperature was 1478 K, and the turbine was designed with blades thick enough for internal cooling passages. The rotor tip diameter was limited to 86 percent of optimum in order to obtain a reduced tip speed design. The turbine was fabricated with solid, uncooled blading and tested in air at nominal inlet pressure and temperature of 1.379 x 10000 N/sq m and 322.2 K, respectively. Results indicated the turbine total efficiency to be 5.3 points less than design. Analysis of these results has indicated the deficit in performance to be due to stator secondary flow losses, vaneless space surface friction losses, and trailing edge wake mixing losses.

Mclallin, K. L.↗
NASA NTRS1961

Effects at Mach Numbers of 1.61 and 2.01 of Camber and Twist on the Aerodynamic Characteristics of Three Swept Wings Having the Same Planform

An investigation has been made at Mach numbers of 1.61 and 2.01 to determine the aerodynamic characteristics of three wings having a sweepback of 50 deg at the quarter-chord line, a taper ratio of 0.20, an NACA 65A005 thickness distribution, and an aspect ratio of 3.5. One wing was flat, one had at each spanwise station an a = 0 mean line modified to have a maximum height of 4-percent chord, and one had a linear variation of twist with 6 deg of washout at the tip. Tests were made with natural and fixed transition at Reynolds numbers ranging from 1.2 x 10(exp 6) to 3.6 x 10(exp 6) through an angle-of-attack range of -20 deg to 20 deg. When compared with the flat wing, the effect of the linear variation of twist with 6 deg of washout at the tip was to increase the lift-drag ratio when the leading edge was subsonic; but little increase in lift-drag ratio was obtained when the leading edge was supersonic. Pitching moment was increased and gave a positive trim point without greatly affecting the rate of change of pitching moment with lift coefficient. For the cambered wing the high minimum drag resulted in comparatively low lift-drag ratios. In addition, the pitching moments were decreased so that a negative trim point was obtained.

Landrum, Emma Jean↗
NASA NTRS1997

Incompressible Navier-Stokes Computations in Aerospace and Beyond

Challenges in applying CFD to real world problems will be discussed using incompressible flow examples. Despite the remarkable progress made in CFD technology during the past two decades, new challenges are ahead of us. Some of these will be discussed in conjunction with the incompressible Navier-Stokes solver development and their applications. Computed examples include wing tip vortex formation and propagation, flow simulation of an advanced rocket pump, and an extension of the similar technology to biofluid analysis and design. Numerical issues dealing with these applications will be discussed both from algorithm development and from application point of view. The material will be printed in a bound volume after the symposium.

Kwak, Dochan↗
NASA NTRS2011

Simplified Architecture for Precise Aiming of a Deep-Space Communication Laser Transceiver

The simplified architecture is a minimal system for a deep-space optical communications transceiver. For a deepspace optical communications link the simplest form of the transceiver requires (1) an efficient modulated optical source, (2) a point-ahead mechanism (PAM) to compensate for two-way light travel, (3) an aperture to reduce the divergence of the transmit laser communication signal and also to collect the uplink communication signal, and (4) a receive detector to sense the uplink communication signal. Additional components are introduced to mitigate for spacecraft microvibrations and to improve the pointing accuracy. The Canonical Transceiver implements this simplified architecture (see figure). A single photon-counting smart focal plane sensor combines acquisition, tracking, and forward link data detection functionality. This improves optical efficiency by eliminating channel splits. A transmit laser blind sensor (e.g. silicon with 1,550-nm beam) provides transmit beam-pointing feedback via the two-photon absorption (TPA) process. This vastly improves the transmit/receive isolation because only the focused transmit beam is detected. A piezoelectric tiptilt actuator implements the required point-ahead angle. This point-ahead mechanism has been demonstrated to have near zero quiescent power and is flight qualified. This architecture also uses an innovative 100-mHz resonant frequency passive isolation platform to filter spacecraft vibrations with voice coil actuators for active tip-tilt correction below the resonant frequency. The canonical deep-space optical communications transceiver makes synergistic use of innovative technologies to reduce size, weight, power, and cost. This optical transceiver can be used to retire risks associated with deep-space optical communications on a planetary pathfinder mission and is complementary to ongoing lunar and access link developments.

Ortiz, Gerard G.↗