Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “THERMODYNAMIC MODEL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

Chiral thermodynamics of dense hadronic matter

We discuss phases of hot and dense hadronic matter using chiral Lagrangians. A two-flavored parity doublet model constrained by the nuclear matter ground state predicts chiral symmetry restoration. The model thermodynamics is shown within the mean-field approximation. A field-theoretical constraint on possible phases from the anomaly matching is also discussed.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Searching for Suitable Binary Fluid for an Ejector Heat Pump for Domestic Water Heating

Water heating is a major source of energy consumption in the U.S. residential sector. Heat pumps can significantly increase the energy efficiency of water heating. An ejector heat pump (EHP) is a novel, thermally driven heat pump that uses an ejector as a thermocompressor. Choosing suitable working fluids is critical in developing high-performance EHPs. Therefore, this research screens binary fluid pairs (BFPs) for EHPs to produce domestic hot water at a high coefficient of performance (COP). The criteria for screening BFP candidates for EHP water heaters (EHPWHs) are established, and BFP candidates are shortlisted. This study identifies HFE7000, Novec649, HFE7100, HFE7200, and HFE7500 for the primary fluids and RE170, R600a, R600, and R1234ze(Z) for the secondary fluids. The thermodynamic model is employed to investigate the performance of EHPWHs using the shortlisted BFPs under various operating parameters, including the evaporation pressure of the primary working fluid in the high-temperature evaporator and the condensation temperature. In conclusion, the highest heating-cycle COP of 1.328 is achieved by an EHPWH operating with HFE7000/R600 at a condenser temperature of 50 °C and a pressure of 1.69 MPa in the high-temperature evaporator.

42 ENGINEERING↗

The impact of sulphate and magnesium on chloride binding in Portland cement paste

The effect of magnesium and sulphate present in sea water on chloride binding in Portland cement paste was investigated. Ground well hydrated cement paste was exposed to MgCl{sub 2}, NaCl, NaCl + MgCl{sub 2}, MgSO{sub 4} + MgCl{sub 2} and artificial sea water solutions with a range of concentrations at 20 °C. Chloride binding isotherms are determined and pH of the solutions were measured. A selection of samples was examined by SEM-EDS to identify phase changes upon exposure. The experimental data were compared with calculations of a thermodynamic model. Chloride binding from sea water was similar to chloride binding for NaCl solutions. The magnesium content in the sea water lead to a slight decrease in pH, but this did not result in a notable increase in chloride binding. The sulphate present in sea water reduces both chloride binding in C–S–H and AFm phases, as the C–S–H incorporates more sulphates instead of chlorides, and part of the AFm phases converts to ettringite.

36 MATERIALS SCIENCE↗

Giant electrocaloric effect in asymmetric ferroelectric tunnel junctions at room temperature

Room-temperature electrocaloric properties of Pt/BaTiO{sub 3}/SrRuO{sub 3} ferroelectric tunnel junctions (FTJs) are studied by using a multiscale thermodynamic model. It is found that there is a divergence in the adiabatic temperature change ΔT for the two opposite polarization orientations. This difference under a typical writing voltage of 3 V can reach over 1 K as the barrier thickness decreases. Thanks to the ultrahigh external stimulus, a giant electrocaloric effect (1.53 K/V) with ΔT being over 4.5 K can be achieved at room temperature, which demonstrates the perspective of FTJs as a promising solid-state refrigeration.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Strain engineered barium strontium titanate for tunable thin film resonators

Piezoelectric properties of epitaxial (001) barium strontium titanate (BST) films are computed as functions of composition, misfit strain, and temperature using a non-linear thermodynamic model. Results show that through adjusting in-plane strains, a highly adaptive rhombohedral ferroelectric phase can be stabilized at room temperature with outstanding piezoelectric response exceeding those of lead based piezoceramics. Furthermore, by adjusting the composition and the in-plane misfit, an electrically tunable piezoelectric response can be obtained in the paraelectric state. These findings indicate that strain engineered BST films can be utilized in the development of electrically tunable and switchable surface and bulk acoustic wave resonators.

36 MATERIALS SCIENCE↗

Influence of fuel ash on the recoverability of copper from the spent material of chemical looping combustion

Chemical looping combustion (CLC) is an advanced energy production technology that inherently separates the CO 2 generated. The oxygen needed for fuel conversion is supplied by the oxygen carrier. When using copper-based oxygen carriers, oxygen carrier attrition is a challenge to the process economics, unless the attrited copper that is mixed with fuel ash in the spent material can be recovered by, for instance, acid leaching. However, fuel ash may transform the attrited copper into certain complexes of low leachability (e.g., CuAl 2 O 4 ), hindering the copper recovery. In this study, the copper content in the spent material was first evaluated. The effects of ash composition and copper content on the occurrence mode of copper in spent material were predicted by thermodynamic modeling. Redox cycles of simulated spent materials based on various coal ashes were performed to reveal the characteristics of CuAl 2 O 4 /CuFe 2 O 4 formation. The CuO-Al 2 O 3 reaction was investigated under the temperatures and solid residence times experienced in CLC. The materials were analyzed by X-ray diffraction. The results suggest that the fuel ash with a high Al/Ca ratio may lower the recoverability of copper when the temperature is above 925 °C. The slow formation of CuFe 2 O 4 is not expected to affect the copper recovery.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Thermodynamic Analysis of the Conformational Stability of a Single-Domain Therapeutic Antibody

The stability of a new single-domain therapeutic antibody to the ErbB3 receptor was studied by fluorescence spectroscopy at different concentrations of a denaturing agent and temperatures. The analysis of experimental denaturation curves allowed us to build a complete thermodynamic model of unfolding and to determine all parameters of the transition: ΔG = 8.5 kcal mol{sup –1}, T{sub m} = 76°C, ΔH{sub m} = 107 kcal mol{sup –1}, ΔC{sub p} = 1.8 kcal K{sup –1} mol{sup –1}. The obtained data evidence the high stability of the antibody in a broad range of conditions, which is essential for further structural and functional studies and possible therapeutic application.

60 APPLIED LIFE SCIENCES↗

Optimization of Mineralogy and Microstructure of Solidified Basic Oxygen Furnace Slag Through SiO{sub 2} Addition or Atmosphere Control During Hot-Stage Slag Treatment

Valorization of basic oxygen furnace (BOF) slag is of significant importance for mitigation of the steel production’s environmental impact. The present work aims to investigate the influence of SiO{sub 2} addition and oxygen partial pressure on the mineralogical modification of a typical industrial BOF slag. The slag basicity (mass ratio of CaO/SiO{sub 2}) was varied from 1.8 to 4.4 by mixing specific amounts of SiO{sub 2} with the master BOF slag. The original and modified slags were remelted and solidified under argon or air atmosphere followed by slow cooling. The experimental observations were then compared with the results of thermodynamic modeling to achieve a thorough understanding. With decreasing the basicity, free lime was eliminated, as it forms dicalcium silicate (Ca{sub 2}SiO{sub 4}). With increasing oxygen partial pressure, wustite was oxidized to hematite, which combined with free lime to form calcium aluminoferrite (C{sub 2}AF). The effects of SiO{sub 2} addition and oxygen partial pressure were finally evaluated with respect to the energy consumption for the BOF slag valorization. The modified slag is suitable as a precursor for construction applications as binders.

36 MATERIALS SCIENCE↗

A data driven control strategy for optimal and flexible operation of absorption systems; Stratégie de régulation fondée sur les données pour un fonctionnement optimal et flexible des systèmes à absorption

A novel control strategy for vapor absorption systems with experimental validation is presented. Statistical methods are used to integrate a detailed thermodynamic model and system-specific characteristics into a model based control algorithm. This allows for continuously optimized operation as well as fast response to variations in operating conditions. Autonomous controller performance was tested experimentally for response to changes in heat sink and evaporator temperatures. Continuous turndown with fast response to capacity demand changes, in contrast to suboptimal on/off control, was demonstrated. The thermal compressor concept was employed to develop the variable speed thermal compressor module, with aspects specific to absorption heat pumps, also facilitating cross-applicability of vapor compression system control strategies. Our results of this study enable further development and optimization of absorption systems for a wide range of applications.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Phase stability in cast and additively manufactured Al-rich Al-Cu-Ce alloys

Additively manufactured (AM) eutectic Al alloy systems have been studied extensively for advantageous thermal stability and mechanical properties due to their refined microstructures. Al-Cu-Ce alloys are one subset of these AM eutectic alloys. Here we studied phase stability in AM Al-Cu-Ce alloys and compared it to that of conventionally cast ones. A new phase, Al 8 Cu 3 Ce, was identified in the microstructures of both AM and cast Al-Cu-Ce alloys. This Al 8 Cu 3 Ce phase was not previously included on experimental or thermodynamically calculated phase diagrams of the Al-Cu-Ce system. Therefore, we performed additional thermodynamic modeling of the system. These models were experimentally validated with cast and subsequently heat-treated Al-Cu-Ce alloys. We found that despite the refined microstructure of the AM alloys, the phases formed were consistent with the cast alloys, suggesting that AM processing did not significantly alter the formation and stability of phases from that in the conventional alloys. In conclusion, this work has resolved inconsistent previous descriptions of the Al-Cu-Ce ternary phase diagram in the Al-rich region and resulted in the addition of the Al 8 Cu 3 Ce as an equilibrium phase above 500 °C.

36 MATERIALS SCIENCE↗

Impact of thermal stress on the piezoelectric and dielectric properties of PbTiO{sub 3} thick films on various substrates

The impact of thermal stress on the polarization, as well as dielectric and piezoelectric properties of (001) oriented PbTiO{sub 3} (PTO) thick films deposited on various substrates was investigated based on Landau-Devonshire thermodynamic model. The results showed that dielectric and piezoelectric properties of PTO films depend strongly on the thermal stress in PTO films decided by the deposition temperature T{sub G} and the thermal expansion coefficients' difference between PTO films and substrates. For IC-compatible substrates such as Si, c-sapphire, and a-sapphire that induce tensile in-plane thermal stresses, the dielectric and piezoelectric responses and tunabilities of PTO films were enhanced. Whereas for PTO films on MgO, compressive thermal in-plane stresses can degraded the dielectric and piezoelectric responses and tunabilities of the films.

36 MATERIALS SCIENCE↗

Synthesis of Zirconium Diboride Films and ZrB{sub 2}/BC{sub x}N{sub y} Heterostructures

Using mechanochemical synthesis, we have prepared zirconium borohydride, Zr(BH{sub 4}){sub 4}, as a precursor for ZrB{sub 2} film growth by chemical vapor deposition. We have carried out the thermodynamic modeling of phase formation processes in the Zr–B–(N)–H and Zr–B–(N)–H–O systems in a wide temperature range, from 100 to 2500°C, at various p{sub (H2)}/p{sub (Zr(BH4)4)} and p{sub (NH3)}/p{sub (Zr(BH4)4)} partial pressure ratios in the starting gas mixtures. A process has been proposed for the growth of zirconium diboride films by Zr(BH{sub 4}){sub 4} decomposition using two techniques: chemical vapor deposition and plasma-enhanced chemical vapor deposition. We also developed a process for the growth of multilayer ZrB{sub 2}-and BC{sub x}N{sub y}-based structures.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Electrocaloric properties of ferroelectric-paraelectric superlattices controlled by the thickness of paraelectric layer in a wide temperature range

As functions of the paraelectric layer thickness, misfit strain and temperature, the electrocaloric properties of ferroelectric-paraelectric superlattices are investigated using a time-dependent Ginzburg-Landau thermodynamic model. Ferroelectric phase transition driven by the relative thickness of the superlattice is found to dramatically impact the electrocaloric response. Near the phase transition temperature, the magnitude of the electrocaloric effect is maximized and shifted to lower temperatures by increasing the relative thickness of paraelectric layer. Theoretical calculations also imply that the electrocaloric effect of the superlattices depends not only on the relative thickness of paraelectric layer but also on misfit strain. Furthermore, control of the relative thickness of paraelectric layer and the misfit strain can change availably both the magnitude and the temperature sensitivity of the electrocaloric effect, which suggests that ferroelectric-paraelectric superlattices may be promising candidates for use in cooling devices in a wide temperature range.

36 MATERIALS SCIENCE↗

Thermodynamic parametric analysis of refueling heavy-duty hydrogen fuel-cell electric vehicles

Reliable design and safe operation of heavy-duty hydrogen refueling stations are essential for the successful deployment of heavy-duty fuel cell electric vehicles (FCEVs). Fueling heavy-duty FCEVs is different from light-duty vehicles in terms of the dispensed hydrogen quantities and fueling rates, requiring tailored fueling station design for each vehicle class. In particular, the selection and design of the onboard hydrogen storage tank system and the fueling performance requirements influence the safe design of hydrogen fueling stations. A thermodynamic modeling and analysis are performed to evaluate the impact of various fueling parameters and boundary conditions on the fueling performance of heavy-duty FCEVs. Here, we studied the effect of dispenser pressure ramp rate and precooling temperature, initial tank temperature and pressure, ambient temperature, and onboard storage design parameters, such as onboard storage pipe diameter and length, on the fueling rate and final vehicle state-of-charge, while observing prescribed tank pressure and temperature safety limits. An important finding was the sensitivity of the temporal fueling rate profile and the final tank state of charge to the design factors impacting pressure drop between the dispenser and vehicle tank, including onboard storage pipe diameter selection, and flow coefficients of nozzle, valves, and fittings. The fueling rate profile impacts the design and cost of the hydrogen precooling unit upstream of the dispenser.

08 HYDROGEN↗

Degradation mechanism of blended cement pastes in sulfate-bearing environments under applied electric fields: Sulfate attack vs. decalcification

Applied electric fields, the reason behind stray currents, accelerate the ingress of sulfate into cementitious materials. To identify mitigation approaches, this study investigates the effects of slag and fly ash on sodium sulfate attacks of cement pastes under a constant electric current. The mineralogical alterations induced by the attacks were analyzed using X-ray diffractometry, thermogravimetric analysis, scanning electron microscopy, and thermodynamic modeling. The dissolution of aluminates in the slag and fly ash induced a monosulfate-rich area (>~20 mm from the cathode surface) to form next to the ettringite-rich area on the sample surface (<~20 mm). This effect reduced the availability of SO 4 2– in the pore solution, thereby hindering the penetration of sulfate. Meanwhile, the consumption of portlandite by the pozzolanic reaction lowered the decalcification resistance of the materials. This produced a wide area that endured the decomposition of portlandite and carbonate-AFm. Altogether, blending 30% fly ash did not improve the resistance of the material to either sulfate attacks or decalcification; blending 50% slag can effectively mitigate sulfate ingress, though decalcification may become a governing mechanism in the degradation process.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Tailoring dielectric properties of ferroelectric-dielectric multilayers

We develop a nonlinear thermodynamic model for multilayer ferroelectric heterostructures that takes into account electrostatic and electromechanical interactions between layers. We concentrate on the effect of relative layer fractions and in-plane thermal stresses on dielectric properties of Ba{sub 0.6}Sr{sub 0.4}TiO{sub 3}-, BaTiO{sub 3}-, and PbZr{sub 0.2}Ti{sub 0.8}O{sub 3} (PZT)-SrTiO{sub 3} (STO) multilayers on Si and c-sapphire. We show that dielectric properties of such multilayers can be significantly enhanced by tailoring the growth/processing temperature and the STO layer fraction. Our computations show that large tunabilities (∼90% at 400 kV/cm) are possible in carefully designed barium strontium titanate-STO and PZT-STO even on Si for which there exist substantially large in-plane strains.

36 MATERIALS SCIENCE↗

Pyroelectric response of lead zirconate titanate thin films on silicon: Effect of thermal stresses

Ferroelectric lead zirconate titanate [Pb(Zr{sub x}Ti{sub 1-x}O){sub 3}, (PZT x:1-x)] has received considerable interest for applications related to uncooled infrared devices due to its large pyroelectric figures of merit near room temperature, and the fact that such devices are inherently ac coupled, allowing for simplified image post processing. For ferroelectric films made by industry-standard deposition techniques, stresses develop in the PZT layer upon cooling from the processing/growth temperature due to thermal mismatch between the film and the substrate. In this study, we use a non-linear thermodynamic model to investigate the pyroelectric properties of polycrystalline PZT thin films for five different compositions (PZT 40:60, PZT 30:70, PZT 20:80, PZT 10:90, PZT 0:100) on silicon as a function of processing temperature (25–800 °C). It is shown that the in-plane thermal stresses in PZT thin films alter the out-of-plane polarization and the ferroelectric phase transformation temperature, with profound effect on the pyroelectric properties. PZT 30:70 is found to have the largest pyroelectric coefficient (0.042 μC cm{sup −2} °C{sup −1}, comparable to bulk values) at a growth temperature of 550 °C; typical to what is currently used for many deposition processes. Our results indicate that it is possible to optimize the pyroelectric response of PZT thin films by adjusting the Ti composition and the processing temperature, thereby, enabling the tailoring of material properties for optimization relative to a specific deposition process.

36 MATERIALS SCIENCE↗

The role of carbon in extrasolar planetary geodynamics and habitability

The proportions of oxygen, carbon, and major rock-forming elements (e.g., Mg, Fe, Si) determine a planet's dominant mineralogy. Variation in a planet's mineralogy subsequently affects planetary mantle dynamics as well as any deep water or carbon cycle. Through thermodynamic models and high pressure diamond anvil cell experiments, we demonstrate that the oxidation potential of C is above that of Fe at all pressures and temperatures, indicative of 0.1-2 Earth-mass planets. This means that for a planet with (Mg+2Si+Fe+2C)/O > 1, excess C in the mantle will be in the form of diamond. We find that an increase in C, and thus diamond, concentration slows convection relative to a silicate-dominated planet, due to diamond's ∼3 order of magnitude increase in both viscosity and thermal conductivity. We assert then that in the C-(Mg+2Si+Fe)-O system, there is a compositional range in which a planet can be habitable. Planets outside of this range will be dynamically sluggish or stagnant, thus having limited carbon or water cycles leading to surface conditions inhospitable to life as we know it.

79 ASTRONOMY AND ASTROPHYSICS↗