Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TAN”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Assessment of sulfur trioxide formation due to enhanced interaction of nitrogen oxides and sulfur oxides in pressurized oxy-combustion

Pressurized oxy-combustion is emerging to be one of the best technologies for significantly decreasing the energy penalty for CO 2 capture in coal-fired power plants. However, the higher pressure boosts the formation of acid gases, including SO 3 and NO 2 , which could increase the risk of corrosion. The synergistic promotion of SO 3 and NO 2 formation in pressurized oxy-combustion is kinetically evaluated under representative conditions (1 ~ 30 atm, 600 ~ 1200 °C, NO/SO 2 = 0.1 ~ 5). We begin with a comprehensive mechanism (72 species and 428 reactions), covering nitrogen and sulfur chemistry, relying on GRI-Mech 3.0. This analysis shows that the interaction of SO X and NO X enhances the conversion rates of SO 2 → SO 3 , and this effect is more apparent at elevated pressures and lower temperatures. Mechanism analyses indicate that at elevated pressures, the formation pathways of SO 3 through HOSO 2 + O 2 = SO 3 + HO 2 , and NO 2 through HO 2 + NO = NO 2 + OH, are promoted due to the strong interaction between SO X and NO X . The intermediate between these two reactions is SO 2 + OH + M = HOSO 2 + M, resulting in a strong cycle, that can be expressed by the global reaction NO + SO 2 + O 2 = NO 2 + SO 3 . Finally, a nine-step reduced chemistry is developed and validated to accurately predict the formation of SO 3 in the post-flame region at elevated pressures.

42 ENGINEERING↗
DOE OSTI2025

Rheology and engine performance of very low sulfur fuel oil blended with 10% fast pyrolysis and hydrothermal liquefaction oils in a 2-stroke crosshead engine

The performance and emissions for a downscaled single-cylinder 2-stroke crosshead engine were determined for a very low sulfur fuel oil (VLSFO) when blended with 10 wt.% fast pyrolysis (FP) or hydrothermal liquefaction (HTL) bio-intermediates. The FP and HTL oils were derived from biomass and were observed to contain lower molecular weight (MW) hydrocarbons than neat VLSFO (which was evaluated as a baseline comparison). The addition of either biofuel reduced the overall viscosity of the VLSFO. Aging tests at 50, 90, and 120°C showed that the dynamic viscosity of VLSFO increased with exposure time up to two weeks. Similar trends were observed for the FP and HTL blends, but a pronounced spike in viscosity occurred for these fuels during the early period of exposure. None of the viscosity increases exceeded the operational limits of fuel system pumps. Engine performance studies were conducted under low, medium and high load operational settings. The relative performance of the test fuels was highly dependent on operating condition. In general, the engine results for the three test fuels were similar, but modest improvements in brake thermal efficiency and brake specific fuel consumption were observed, which may be attributed to the heightened reactivity of low molecular weight fraction of the FP and HTL oils.

09 BIOMASS FUELS↗
DOE OSTI2020

Radiological analysis and transmutation calculation of representative castable nanostructured alloys

In this work, radiological analysis regarding the waste management was performed on two current reduced-activation ferritic-martensitic (RAFM) steels Eurofer 97 and F82H and two castable nanostructured alloys (CNAs) CNA1 and CNA3 using the European DEMO first wall spectrum. CNA1 and CNA3 are a new generation of RAFM steels, which have increased amounts of nanoscale carbonitrides and carbides precipitates, respectively, via small composition modifications. Furthermore, the increased nitrogen in CNA1 leads to higher activity at ≥50 years, and thus to the disposal concern under the current NRC regulation. However, the calculation using Fetter’s evaluation leads to reduced waste disposal rating (WDR) of down to 0.25 depending on the damage dose from ~0.05 wt percent nitrogen in CNA1, and thus less concern on the waste disposal. Contact dose rate after 10 years from the first wall replacement primarily depends on the initial Co and Nb impurity levels. Other added elements, such as V and Si in CNA1 and Ti and Mn in CNA3, do not have significant effect on the specific activity, contact dose rate, or decay heat. Composition limits of CNAs are given based on the shallow burial disposal and materials recycling. In addition, composition evolution of typical precipitates in the CNAs was calculated using the DEMO first wall and the HFIR spectra. Larger transmutation-induced composition evolution occurs in the V/Ta-rich carbonitrides in CNA1 than that in the Ti-rich carbides in CNA3.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Water film-driven Mn (oxy)(hydr)oxide nanocoating growth on rhodochrosite

Minerals exposed to moist air stabilize thin water films that drive a score of chemical reactions of great importance to water-unsaturated terrestrial environments. In this study, we identified Mn (oxy)(hydr)oxide nanocoatings formed by the dissolution, oxidation and precipitation of Mn in oxygenated water films grown on rhodochrosite (MnCO 3 ) microparticles. Nanocoatings that could be identified by vibrational spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and (scanning and transmission) electron microscopy formed in water films containing the equivalent of at least 7 monolayers (~84 H 2 O/nm 2 ). These films were formed by exposing microparticles to moist air with at least 50% relative humidity (RH). Films of neutral pH reacted up to 14% of the Mn II located in the topmost ~5 nm region of the microparticles in atmospheres of up to 90% RH for 7 d. These reactions produced MnOOH, birnessite (MnO 2 ) and hausmannite (Mn 3 O 4 ) nanoparticles of low crystallinity, while exposure to atmospheric air for 1 yr. converted only 2% of Mn II in this region to MnOOH. In contrast, reactions in alkaline water films converted up to ~75% of the Mn II but only after 16 d of reaction. These films produced MnOOH and MnO 2 of low crystallinity, as well as crystalline hausmannite. Kinetic modeling of the time-resolved growth of the Mnsingle bondO stretching vibrational bands of these nanocoatings revealed two concurrent reaction processes. A 1 rst -order process was assigned to nucleation events terminating only after a few hours, and a 0-order process was assigned to the sustained growth of nanocoatings from these nuclei over longer reaction time. By identifying nanocoatings formed by water film-driven reactions on rhodochrosite, our study adds new insight into mineralogical transformations relevant to anoxic–oxic boundaries in water-unsaturated environments.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

How deep is your soil? Quantifying and spatially analyzing understudied deep soil in the United States

Deep soil is largely understudied and important in understanding biogeochemical processes in soil. Here, understudied soil is defined as the difference between soil studied to a known depth and the estimated bedrock depth. To understand more about deep soil, the understudied soil in the US was quantified and spatially analyzed using soil survey data and model estimates of bedrock depth. An equation was derived to find understudied soil using the dataset parameters “max lower depth studied”, “depth to bedrock”, and “likelihood of bedrock in the top 200 cm”. The survey data and bedrock model revealed that soil has been studied to an average depth of 1-2 meters, and the average depth to bedrock is 20 meters. Soil data density in the soil surveys was greatest in the West Coast, Midwest, and areas historically managed for agricultural, while the non-contiguous US and interior West were underrepresented. The soil had been studied deeper than the estimated soil depth in 455 out of 56,889 observation points concentrated in Alaska, California, Texas, Florida, Puerto Rico, and the US Virgin Islands. To understand the diversity and any taxonomic bias of the global soil data available, soil order was compared to US-based National Resource Conservation Service percentages and it was found that Oxisols, Alfisols, Ultisols, Andisols, and Histosols were overrepresented while Gelisols, Aridisols, Vertisols, Entisols, and Spodosols are underrepresented. Soil depth is important in exploring the complexity of biogeochemical processes that take place in soil.

Bedrock↗
DOE OSTI2020

X-Ray Fluorescence Microscopy: A Method of Measuring Ion Concentrations in the Ear

This technical note describes synchrotron x-ray fluorescence microscopy (XFM) as a method for measuring the concentrations of various elements in cross-sections of the ear at extremely high resolution. This method could be of great importance for addressing many open questions in hearing research. XFM uses synchrotron radiation to evoke emissions from many biologically relevant elements in the tissue. The intensity and wavelength of the emitted radiation provide a fingerprint of the tissue composition that can be used to measure the concentration of the elements in the sampled location. Here, we focus on energies that target biologically-relevant elements of the periodic table between magnesium and zinc. Since a highly focused x-ray beam is used, the spot size is well below 1 mu m and the samples can be scanned at a nanometer lateral resolution. This study shows that measurement of the concentrations of different elements is possible in a mid-modiolar cross-section of a mouse cochlea. Images are presented that indicate potassium and chloride "hot spots" in the spiral ligament and the spiral limbus, providing experimental evidence for the potassium recycling pathway and showing the cochlear structures involved. Scans of a section obtained from the incus, one of the middle ear ossicles, in a developing mouse have shown that zinc is not uniformly distributed This supports the hypothesis that zinc plays a special role in the process of ossification. Although limited by sophisticated sample preparation and sectioning, the method provides ample exciting opportunities, to understand the role of genetics and epigenetics on hearing mechanisms in ontogeny and phylogeny.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

Siegert-pseudostate formulation with B-splines

Siegert states (SSs) serve as a useful basis for studying quantum scattering from finite-range potentials. Since they form a discrete instead of continuous set of eigen-solutions, SSs are convenient for performing electronic structure calculations in atoms, molecules, and plasmas. Numerical instabilities may arise, however, in the computation of SSs if the potential vanishes for some extended region, a situation commonly occurring in plasma calculations. Here, in this paper, we identify the cause of these instabilities as the use of non-localized radial basis functions. We thus advocate the use of localized radial basis functions, in particular B-splines, for more robust computations of SSs.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2026

Electron-impact ionization from excited states method

We present a distorted-wave with exchange (DWE) formulation for computing electron-impact ionization (EII) cross sections within the recently developed excited states method (ESM) for plasmas. The ESM provides a self-consistent quantum-mechanical description of both bound and continuum electronic states in dense plasmas, incorporating finite-temperature and screening effects absent in isolated-atom approaches. Using this framework, we calculate EII cross sections for lithium across a wide range of temperatures and densities. We show that the ESM reproduces the isolated-atom limit at low densities while capturing strong plasma effects, such as pressure ionization and shape resonances, at solid density. Comparisons with isolated-atom DWE and average-atom (AA) calculations reveal that, although AA cross sections can approximate configuration average behavior, the ESM provides more accurate, state-resolved answers. In conclusion, these results demonstrate that the ESM allows one to obtain rate coefficients for collisional-radiative modeling of plasmas out of local thermodynamical equilibrium.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Power system inertia estimation: Review of methods and the impacts of converter-interfaced generations

Understanding and quantifying the inertia of power systems with the integration of converter-interfaced generation (CIG) plays an essential role in the safe transition to a future low-inertia scenario. Here we provide a comprehensive summary of inertia definitions for both synchronous generators and CIGs as well as their corresponding estimation methods. In particular, the estimation methods are categorized as model-based and measurement-based approaches considering both small and large disturbances. The advantages and disadvantages of different methods are carefully discussed. This paper also offers for the first time a framework to quantify the virtual inertia of CIGs at the component and aggregation levels, an open problem in the literature. Finally, future directions for inertia estimation are identified and discussed. This significantly benefits the design of appropriate control and protection schemes in achieving a more reliable, secure, and resilient power system.

42 ENGINEERING↗
DOE OSTI2021

Decentralized Data-Driven Estimation of Generator Rotor Speed and Inertia Constant Based on Adaptive Unscented Kalman Filter

This paper proposes an online decentralized and data-driven method for synchronous generator rotor speed and inertia estimation. First, an analytical relationship between the generator terminal voltage/current phasors and its internal rotor speed is derived using the Thevenin equivalent. The parameters of the latter are obtained via a recursive estimator, which allows us to estimate the generator's internal rotor speed from voltage/current phasors without the need for any generator information. Second, we reformulate the equivalent swing equation into the Kalman filter form, which enables us to use a priori-estimated internal rotor speed along with measured real and reactive power injections to obtain an estimate of the inertia for each online synchronous generator. This is achieved through an adaptive unscented Kalman filter. We demonstrate that the use of terminal bus frequency to approximate the rotor speed for inertia estimation by existing methods leads to large estimation biases/errors. Numerical simulations carried out on the IEEE 39-bus and Texas 2000-bus systems reveal that our proposed method is consistently more accurate than existing methods. Moreover, our proposed method is insensitive to both the type and location of system disturbances, and it is robust to different levels of measurement noise.

bus frequency↗
DOE OSTI2025

Derivation of physical equations for high-speed laser welding using large language models

It is challenging to formulate complex physical phenomena that occur in a manufacturing process, particularly when the available data are limited, rendering conventional data-driven approaches ineffective. This study aims to predict humping onset in high-speed laser welding by introducing a novel framework, namely text-to-equations generative pre-trained transformer (T2EGPT). This method leverages the capabilities of large language models (LLMs), in combination with sparse experimental data and enriched literature data, to derive an interpretable and generalizable equation for predicting humping initiation. By capturing key correlations among physical parameters, T2EGPT generates a compact and dimensionless expression that accurately predicts hump formation. The equation reveals that humping arises from the interplay between inertia-driven backward melt flow and capillary-driven surface stabilization, where inertial forces drive molten metal backward and capillary forces resist surface deformation. Furthermore, compared to traditional data-driven models, T2EGPT demonstrates enhanced predictive accuracy and cross-material transferability. More broadly, this study highlights the potential of LLMs to integrate textual information with data-driven discovery, enabling the extraction of physical laws in data-scarce scientific domains.

36 MATERIALS SCIENCE↗
DOE OSTI2021

A predictive discrete-continuum multiscale model of plasticity with quantified uncertainty

Multiscale models of materials, consisting of upscaling discrete simulations to continuum models, are unique in their capability to simulate complex materials behavior. The fundamental limitation in multiscale models is the presence of uncertainty in the computational predictions delivered by them. In this work, a sequential multiscale model has been developed, incorporating discrete dislocation dynamics (DDD) simulations and a strain gradient plasticity (SGP) model to predict the size effect in plastic deformations of metallic micro-pillars. The DDD simulations include uniaxial compression of micro-pillars with different sizes and over a wide range of initial dislocation densities and spatial distributions of dislocations. An SGP model is employed at the continuum level that accounts for the size-dependency of flow stress and hardening rate. Sequences of uncertainty analyses have been performed to assess the predictive capability of the multiscale model. The variance-based global sensitivity analysis determines the effect of parameter uncertainty on the SGP model prediction. The multiscale model is then constructed by calibrating the continuum model using the data furnished by the DDD simulations. A Bayesian calibration method is implemented to quantify the uncertainty due to microstructural randomness in discrete dislocation simulations (density and spatial distribution of dislocations) on the macroscopic continuum model prediction (size effect in plastic deformation). Here, the outcomes of this study indicate that the discrete-continuum multiscale model can accurately simulate the plastic deformation of micro-pillars, despite the significant uncertainty in the DDD results. Additionally, depending on the macroscopic features represented by the DDD simulations, the SGP model can reliably predict the size effect in plasticity responses of the micropillars with below 10% of error.

36 MATERIALS SCIENCE↗