Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SINTERED MATERIALS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

Power Electronics Materials and Bonded Interfaces - Reliability and Lifetime

High temperature operation of wide bandgap devices continue to be a challenge for the power electronics packages. Thermal performance and reliability are important factors that determine the viability of a bonded interface for operation at high temperatures. In this presentation, we present the technical approach and key results from the research on sintered silver, transient liquid phase alloy, and polymeric materials. A lifetime prediction model that incorporates the thermomechanical behavior of sintered silver at 200C was developed. The copper-aluminum transient alloy completed 350 thermal cycles from -40C to 200C and little increase in the defect level was observed. In addition to material research, we initiated a time-series analysis on the scanning acoustic microscope images of eutectic solder to explore statistical forecasting methods and machine learning techniques. Initial results that report the accuracy of a few different statistical models are presented.

ADVANCED PROPULSION SYSTEMS↗

Effect of sintering temperature on the structural and electrical properties of Zn{sub 0.95}Cr{sub 0.05}O

In this communication, we report the results of the studies on the sintering temperature dependent structural properties and dielectric behavior of 5% Cr doped Zn{sub 0.95}Cr{sub 0.05}O samples synthesized by cost effective sol-gel technique. Crystallographic orientations, crystallinity and crystallite size (CS) have been understood by performing X-ray diffraction (XRD) measurement at room temperature. Values of CS have been further verified by carrying out Williamson – Hall (W-H) plot analysis and the difference between the CS from XRD and W-H analyses has been discussed. Dielectric behavior has been studied and its dependence on the sintering temperature has been understood in the light of crystallite size, crystal boundary density and oxygen vacancies induced possible conductivity in the samples.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Effect of Bi doping on morphotropic phase boundary and dielectric properties of PZT

In our present attempt, Pb{sub (1-x)}Bi{sub x}Zr{sub 0.52}Ti{sub 0.48}O{sub 3} [PBZT] {where x = 0, 0.05, 0.1} is synthesized by sol-gel route. Effect of Bi addition on structure, sinterability and dielectric properties are observed. The presence of morphotropic phase boundary (coexistence of tetragonal and rhombohedral symmetry) is confirmed by X-ray diffraction. Enhancement of sinterability after Bi doping is observed through a systematic sintering program. Frequency and temperature dependent dielectric constant are studied. Bi doping in PZT is found to enhance room temperature dielectric constant. However, at high temperature the dielectric constant of pure PZT is more than that of doped PZT.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Reactive sintering of tungsten-doped high strength ZrB{sub 2}–SiC porous ceramics using metastable precursors

Graphical abstract: - Highlights: • Tungsten-doped porous ZrB{sub 2}–SiC specimens were fabricated by reactive sintering. • Both sintering and mechanical properties were improved by doping with tungsten. • Optimum concentration to obtain high mechanical properties was W/Zr (mol) = 0.05. • Sintering might be promoted by self-accelerated diffusion. • Mechanical properties might be improved by solid solution strengthening. - Abstract: Tungsten-doped porous ZrB{sub 2}-20 vol.% SiC specimens with a high strength skeleton were fabricated by reactive sintering using metastable reactants, i.e., as-synthesized amorphous hydrous ZrO{sub 2}–WO{sub 3}/ZrO{sub 2}, amorphous boron, nanocarbon, and β-SiC. Doping with tungsten clearly promoted sintering and improved mechanical properties; the optimum tungsten concentration to obtain high mechanical properties was investigated. A single-phase solid solution (Zr,W)B{sub 2} was formed in the specimens with tungsten. We suggest that sintering was promoted by self-accelerated diffusion owing to the formation of point defects caused by doping with tungsten. The improvement of mechanical properties could be attributed to solid solution strengthening.

36 MATERIALS SCIENCE↗

New Mechanism for Ferroelectricity in the Perovskite Ca 2– x Mn x Ti 2 O 6 Synthesized by Spark Plasma Sintering

Perovskite oxides hosting ferroelectricity are particularly important materials for modern technologies. The ferroelectric transition in the well-known oxides BaTiO 3 and PbTiO 3 is realized by softening of a vibration mode in the cubic perovskite structure. For most perovskite oxides, octahedral-site tilting systems are developed to accommodate the bonding mismatch due to a geometric tolerance factor t = (A–O)/[√2(B–O)] < 1. In the absence of cations having lone-pair electrons, e.g., Bi 3+ and Pb 2+ , all simple and complex A-site and B-site ordered perovskite oxides with a t < 1 show a variety of tilting systems, and none of them become ferroelectric. The ferroelectric CaMnTi 2 O 6 oxide is, up to now, the only one that breaks this rule. It exhibits a columnar A-site ordering with a pronounced octahedral-site tilting and yet becomes ferroelectric at T c ≈ 650 K. Most importantly, the ferroelectricity at T < Tc is caused by an order–disorder transition instead of a displacive transition; this character may be useful to overcome the critical thickness problem experienced in all proper ferroelectrics. Application of this new ferroelectric material can greatly simplify the structure of microelectronic devices. However, CaMnTi2O6 is a high-pressure phase obtained at 7 GPa and 1200 °C, which limits its application. Here we report a new method to synthesize a gram-level sample of ferroelectric Ca 2–x Mn x Ti 2 O 6 , having the same crystal structure as CaMnTi 2 O 6 and a similarly high Curie temperature. The new finding paves the way for the mass production of this important ferroelectric oxide. In conclusion, we have used neutron powder diffraction to identify the origin of the peculiar ferroelectric transition in this double perovskite and to reveal the interplay between magnetic ordering and the ferroelectric displacement at low temperatures.

36 MATERIALS SCIENCE↗

Al{sub 2}O{sub 3}-SrCo{sub 0.6}Fe{sub 0.4}O{sub 3} Membrane Coated on a Meso-Porous Al{sub 2}O{sub 3} Support

In this work, a membrane for oxygen separation from air was a composite system with a mesoporous alumina support and a thin layer with microporous structures. The support was formed into a disc shape using alumina powder following a press-calcination process and subsequently, a nanoscale pore membrane with narrow pore size distribution was infused following a sol-gel approach. The sol-gel method entailed the use of a stable sol prepared from an organo-metallic oxide precursor, followed by deposition of the sol onto the porous support via dip coating. The sol hardened upon drying, and forms thin Al{sub 2}O{sub 3}-SrCo{sub 0.6}Fe{sub 0.4}O{sub 3} active layer after sintering.

36 MATERIALS SCIENCE↗

Reliability and Lifetime Prediction Model of Sintered Silver Under High-Temperature Cycling

Although excellent reliability has been reported for sintered silver as a die-attach material under both thermal and power cycling loads in power electronics applications, the promise of this material as a large-area attachment at temperatures beyond 200 degrees C needs to be investigated. This paper presents insights into the thermomechanical behavior and reliability of sintered silver under extreme thermal cycling conditions. In this study, we bonded sintered silver samples and subjected it to a thermal cycling profile of -40 °C to 200 °C with high ramp rates. We periodically monitored samples under thermal cycling to detect the presence of any failure mechanisms using a scanning acoustic microscope. We also included 95Pb5Sn solder in the study to obtain reference data. Results show the occurrence of cracks in sintered silver followed by a rapid rate of crack growth that exceeded the failure criterion in just 50 cycles. The predominant failure mechanism we observed was adhesive failure. As a large-area attachment, solder exhibited a higher reliability than sintered silver but failed within 100 cycles. Finally, we performed thermomechanical modeling to compute strain energy density values and correlated these with the experimentally observed crack growth rates to formulate a lifetime prediction model for sintered silver.

30 DIRECT ENERGY CONVERSION↗

High rate performances of the cathode material LiNi{sub 1/3}Co{sub 1/3}Mn{sub 1/3}O{sub 2} synthesized using low temperature hydroxide precipitation

Graphical abstract: A low-temperature reaction route is introduced based on hydroxide precipitation method to synthesize a cathode material LiNi{sub 1/3}Co{sub 1/3}Mn{sub 1/3}O{sub 2}. The charge-discharge tests were performed at 1000 mA g{sup -1} between 2.5 and 4.5 V and the discharge capacity is about 160 mAh g{sup -1}. The discharge capacity of the material is strongly impacted by the reaction temperature. The powders sintered at 850 {sup o}C show the best electrochemical performance. Highlights: {yields} A low-temperature reaction route is introduced based on hydroxide precipitation method to synthesize a novel cathode material LiNi{sub 1/3}Co{sub 1/3}Mn{sub 1/3}O{sub 2}. {yields} The charge-discharge tests were performed at higher current as 5 C between 2.5 and 4.5 V. {yields} The discharge capacity of the material is strongly impacted by the reaction temperature. The powders sintered at 850 {sup o}C show the best electrochemical performance. -- Abstract: A low-temperature reaction route is introduced based on hydroxide precipitation method to synthesize the cathode material LiNi{sub 1/3}Co{sub 1/3}Mn{sub 1/3}O{sub 2}. The crystal structure and morphology of the prepared powder have been characterized by X-ray diffraction and Scan electron microscope, respectively. The charge-discharge tests were performed between 2.5 and 4.5 V. The discharge capacity of the material is strongly impacted by the reaction temperature. The powders sintered at 850 {sup o}C show the best electrochemical performance and the initial discharge capacity is about 160 mAh g{sup -1} at 5 C. Powder X-ray diffraction and Scan electron microscope results reveal that the excellent electrochemical performances should be ascribed to the lower precursor reaction temperature, the lower degree of cation mixing and analogous spherical small particles, which can improve the transfer of Li ions and electrons. All these results indicate that this material has potential application in lithium-ion batteries.

36 MATERIALS SCIENCE↗

Fabrication of large sintered pellets of Sb-doped n-type Mg{sub 2}Si using a plasma activated sintering method

Sb is known to be the most stable n-type dopant in Mg{sub 2}Si, whereas the reproducibility and sintering scalability of Sb-doped Mg{sub 2}Si has proved to be difficult. We have developed a metallic binder for the Sb-doped Mg{sub 2}Si sintering process. A remarkable benefit of the binder is that it enables us to reproducibly fabricate large sintered Sb-doped Mg{sub 2}Si pellets up to 30 mm in diameter with no internal cracks. For binder contents of 3-7 wt%, the observed power factor and thermal conductivity were identical to that of conventional Sb-doped samples, while excess binder degraded the TE properties. The binder mixture also plays a part in increasing the yield in the production of TE legs, up to 82% for 5 wt% Ni incorporation, as well as improving the hardness of the sintered sample. Incorporation of 5 wt% Ni binder affected an increase in the ZT value up to 0.97. - Graphical abstract: The sample of 30 mm in diameter is fabricated by using a Ni binder. Highlights: Black-Right-Pointing-Pointer We have developed a metallic binder for the Sb-doped Mg{sub 2}Si sintering process. Black-Right-Pointing-Pointer Sb-doped Mg{sub 2}Si pellets up to 30 mm in diameter with no internal cracks. Black-Right-Pointing-Pointer Incorporation of 5 wt% Ni binder affected an increase in the ZT value up to 0.97.

36 MATERIALS SCIENCE↗

Liquid phase sintered compacts in space

A model that will explain the effect of gravity on liquid phase sintering was developed. Wetting characteristics and density segregation which are the two important phenomena in liquid phase sintering are considered in the model development. Experiments were conducted on some selected material combinations to study the gravity effects on liquid phase sintering, and to verify the validity of the model. It is concluded that: (1) The surface tension forces acting on solid particles in a one-g environment are not appreciably different from those anticipated in a 0.00001g/g sub 0 (or lower) environment. (2) The capillary forces are dependent on the contact angle, the quantity of the liquid phase, and the distance between solid particles. (3) The pores (i.e., bubbles) do not appear to be driven to the surface by gravity-produced buoyancy forces. (4) The length of time to produce the same degree of settling in a low-gravity environment will be increased significantly. (5) A low gravity environment would appear to offer a unique means of satisfactorily infiltrating a larger and/or complex shaped compact.

Mookherji, T. K.↗

Ultra high purity, dimensionally stable INVAR 36

An INVAR 36 material having long-term dimensional stability is produced by sintering a blend of powders of nickel and iron under pressure in an inert atmosphere to form an alloy containing less than 0.01 parts of carbon and less than 0.1 part aggregate and preferably 0.01 part individually of Mn, Si, P, S and Al impurities. The sintered alloy is heat treated and slowly and uniformly cooled to form a material having a coefficient of thermal expansion of less than 1 ppm/C and a temporal stability of less than 1 ppm/year.

Sokolowski, Witold M.↗

Ultra high purity, dimensionally stable INVAR 36

An INVAR 36 material having long-term dimensional stability is produced by sintering a blend of powders of nickel and iron under pressure in an inert atmosphere to form an alloy containing less than 0.01 parts of carbon and less than 0.1 part aggregate and preferably 0.01 part individually of Mn, Si, P, S and Al impurities. The sintered alloy is heat treated and slowly and uniformly cooled to form a material having a coefficient of thermal expansion of less than 1 ppm/C and a temporal stability of less than 1 ppm/year.

Sokolowski, Witold M.↗

Facile etching for single crystal cathode materials

A recycling and synthesis of charge material for secondary batteries generates single-crystal charge materials for producing batteries with greater charge cycle longevity. Charge material particles undergo a heating for fusing or enhancing grain boundaries between polycrystalline particles. The resulting, more well-defined grain boundaries are easily etched by a relatively weak mineral acid solution. The acid solution removes material at the grain boundaries to separate secondary particles into primary particles along the grain boundaries. The resulting single crystal (monocrystalline) charge material particles are washed and filtered, and typically re-sintered to accommodate any needed lithium (lithium carbonate), and result in a charge material with larger surface area, higher lithium diffusivity and lower cation ordering.

Wang, Yan↗

In situ measurement of temperature and reduction of rutile titania using energy dispersive x-ray diffraction

Using in situ energy dispersive x-ray diffraction (EDXRD) the average specimen temperature of TiO 2 in the steady state of flash is experimentally determined. Comparison of the microstructure for flash sintering and conventional sintering in addition to the temperature determined from calibration of the unit cell expansion indicates that rapid Joule heating during flash sintering causes densification and grain growth comparable with conventional sintering. An average temperature approximation model is proposed to account for greybody radiation and thermal conduction. In conclusion, the inhomogeneity of the grain growth across the sample length is confirmed to correlate with inhomogeneity in temperature distribution and this suggests a current induced Peltier effect in n-type TiO 2 .

36 MATERIALS SCIENCE↗

Effect of processing on fracture toughness of silicon carbide as determined by Vickers indentations

Several alpha-SiC materials were processed by hot isostatic pressing (HIPing) and by sintering an alpha-SiC powder containing boron and carbon. Several beta-SiC materials were processed by HIPing a beta-SiC powder with boron and carbon additions. The fracture toughnesses K(sub 1c) of these beta- and alpha-SiC materials were estimated from measurements of Vickers indentations. The three formulas used to estimate K(sub 1c) from the indentation fracture patterns resulted in three ranges of K(sub 1c) estimates. Furthermore, each formula measured the effects of processing differently. All three estimates indicated that fine-grained HIPed alpha-SiC has a higher K(sub 1c) than coarsed-grained sintered alpha-SiC. Hot isostatically pressed beta-SiC, which had an ultrafine grain structure, exhibited a K(sub 1c) comparable to that of HIPed alpha-SiC.

Dannels, Christine M.↗

Optimization of the dissolution of molybdenum disks. FY-16 results

Argonne National Laboratory is providing technical development assistance to NorthStar Medical Technologies LLC in its pursuit of two pathways for production of molybdenum-99: the 98 Mo(n,γ) 99 Mo reaction and the photonuclear reaction, 100 Mo(γ,n) 99 Mo. Processing of irradiated targets, from either production mode, requires dissolution of the target material in H 2 O 2 followed by a concentration step, addition of ferric ion to precipitate impurities, and conversion of the final solution to 5M potassium hydroxide solution of potassium molybdate. Currently, NorthStar is using pressed and sintered Mo disks as targets. Several options are being considered for the design of Mo targets for the production of 99 Mo using the (γ,n) reaction. In the current design, the target holder contains a series of sintered Mo disks lined up perpendicular to two incident electron beams, one entering from each side of the target stack. In this configuration, the front-most disks absorb most of the heat from the electron beam and need to be thinner to allow for better cooling, while the middle of the target can be thicker. Distribution of the total mass of Mo allows for larger masses of Mo material and thus larger production batches of 99 Mo. A limitation of the sintering approach is the production of very thin disks. Recent advances in 3D printing allow for much thinner target components can be achieved than when the traditional press-and-sinter approach is used. We have demonstrated that several factors can play important roles in dissolution behavior: particle size of Mo metal used for production of targets, sintering conditions, degree of open porosity, and thickness of the sintered Mo targets. Here we report experimental results from studies of small-scale dissolution of sintered Mo disks fabricated from various recycled and commercial Mo materials, and dissolution of 3D-printed Mo disks that were fabricated by Oak Ridge National Laboratory (ORNL). We also report on large-scale dissolution studies with 600 g batches of sintered Mo disks.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Bulk Grain-Boundary Materials from Nanocrystals

Grain-boundary engineering is pivotal to fully utilize the mechanical, electrical, and thermal-transport properties of various materials. However, current methods in metallurgy rely almost exclusively on top-down approaches, making precise grain-boundary engineering, especially at nanoscale, difficult to achieve. Herein, we report a method to produce tailored grain-boundary conditions with nanoscale precision from colloidal metal nanocrystals through surface treatment followed by a pressure-sintering process. The resulting bulk grain-boundary materials (which we call “nanocrystal coins”) possess a metal-like appearance and conductivity while inheriting the original domain features of the nanocrystal building blocks. In this work, nanoindentation measurements confirmed the superior mechanical hardness of the obtained materials. Further, we use this method to fabricate, for the first time, a single-component bulk metallic glass from amorphous palladium nanoparticles. Our discovery may spur the development of new materials whose functionality crucially depends on the domain configuration at nanoscale, such as superhard materials, thermoelectric generators, and functional electrodes.

36 MATERIALS SCIENCE↗