Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Recombinant”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Photovoltaic investigation of minority carrier lifetime in the heavily-doped emitter layer of silicon junction solar cell

The results of experiments on the recombination lifetime in a phosphorus diffused N(+) layer of a silicon solar cell are reported. The cells studied comprised three groups of Czochralski grown crystals: boron doped to one ohm-cm, boron doped to 6 ohm-cm, and aluminum doped to one ohm-cm, all with a shunt resistance exceeding 500 kilo-ohms. The characteristic bulk diffusion length of a cell sample was determined from the short circuit current response to light at a wavelength of one micron. The recombination rates were obtained by measurement of the open circuit voltage as a function of the photogeneration rate. The recombination rate was found to be dependent on the photoinjection level, and is positive-field controlled at low photoinjection, positive-field influence Auger recombination at a medium photoinjection level, and negative-field controlled Auger recombination at a high photoinjection level.

Ho, C.-T.↗
NASA NTRS1985

High-efficiency silicon solar-cell design and practical barriers

A numerical evaluation technique is used to study the impact of practical barriers, such as heavy doping effects (Auger recombination, band gap narrowing), surface recombination, shadowing losses and minority-carrier lifetime (Tau), on a high efficiency silicon solar cell performance. Considering a high Tau of 1 ms, efficiency of a silicon solar cell of the hypothetical case is estimated to be around 29%. This is comparable with (detailed balance limit) maximum efficiency of a p-n junction solar cell of 30%. Value of Tau is varied from 1 second to 20 micro. Heavy doping effects, and realizable values of surface recombination velocities and shadowing, are then considered in succession and their influence on cell efficiency is evaluated and quantified. These practical barriers cause the cell efficiency to reduce from the maximum value of 29% to the experimentally achieved value of about 19%. Improvement in open circuit voltage V sub oc is required to achieve cell efficiency greater than 20%. Increased value of Tau reduces reverse saturation current and, hence, improves V sub oc. Control of surface recombination losses becomes critical at higher V sub oc. Substantial improvement in Tau and considerable reduction in surface recombination velocities is essential to achieve cell efficiencies greater than 20%.

Mokashi, A.↗
NASA NTRS1990

Theoretical studies of important processes in planetary and comet atmospheres

Dissociative recombination (DR) reactions in planetary and comet atmospheres are discussed. A computer program was developed which determines DR cross sections and rates using potential curves and electronic capture widths. It uses Multi-Channel Quantum Defect Theory (MQDT) to include excited Rydberg resonance levels in the DR cross section and rate calculations. Each vibrational level of a molecular ion is the limit for an infinite series of Rydberg states. Above each ion vibrational level are Rydberg vibrational levels having higher ion levels as their series limit. These Rydberg vibrational levels are resonances, i.e., neutral states which are imbedded in the electron-molecular ion continuum. The process in which the Rydberg level causes an abrupt perturbation in the cross section for DR (because of interference between capture into the Rydberg level and capture into the repulsive dissociative state) is referred to as indirect recombination. The process in which the Rydberg levels are excluded and recombination goes from the entrance channel to the repulsive state is called direct recombination. The full DR process, i.e., both direct and indirect recombination, is the process of importance for planetary atmospheres. These ideas are illustrated with the new results for DR from excited ion vibrational levels of O2(+) into the dissociative state which leads to O(1S) + O(1D).

Guberman, Steven L.↗
NASA NTRS1991

Theoretical studies of important processes in planetary and comet atmospheres

This is the fifth semi-annual progress report describing research on dissociative recombination reactions in planetary and comet atmospheres. The Appendix has two papers that describe NASA supported research. Both papers have been recently accepted for publication. The first paper, 'The Generation of O(S-1) from the Dissociative Recombination of O2(+)', describes in detail the Multichannel Quantum Defect (MQDT) theory used for the calculation of dissociative recombination (DR) cross sections and rates. The application to the generation of the upper state of the atomic oxygen green line emission is of great importance to the modelling of planetary atmospheres. The second paper in the Appendix, 'Dissociative Recombination of the Ground State of N2(+)', applies the methods described in the first paper to N2(+). We find remarkable agreement with the prior microwave afterglow experiments for both the total recombination rate and for its electron temperature dependence. However, the results disagree with recent merged beams results which gave cross sections that are a factor of five below the microwave afterglow experiments and the current results. DR of N2(+) is an important mechanism for generating energetic N atoms which can escape the atmosphere of Mars. Currently we are also continuing additional work on the DR of O2(+) which is aimed at calculating both the total DR rate as a function of ion vibrational level and the rate for production of O(D-1).

Guberman, Steven L.↗
NASA NTRS2000

Kinetics of DSB rejoining and formation of simple chromosome exchange aberrations

PURPOSE: To investigate the role of kinetics in the processing of DNA double strand breaks (DSB), and the formation of simple chromosome exchange aberrations following X-ray exposures to mammalian cells based on an enzymatic approach. METHODS: Using computer simulations based on a biochemical approach, rate-equations that describe the processing of DSB through the formation of a DNA-enzyme complex were formulated. A second model that allows for competition between two processing pathways was also formulated. The formation of simple exchange aberrations was modelled as misrepair during the recombination of single DSB with undamaged DNA. Non-linear coupled differential equations corresponding to biochemical pathways were solved numerically by fitting to experimental data. RESULTS: When mediated by a DSB repair enzyme complex, the processing of single DSB showed a complex behaviour that gives the appearance of fast and slow components of rejoining. This is due to the time-delay caused by the action time of enzymes in biomolecular reactions. It is shown that the kinetic- and dose-responses of simple chromosome exchange aberrations are well described by a recombination model of DSB interacting with undamaged DNA when aberration formation increases with linear dose-dependence. Competition between two or more recombination processes is shown to lead to the formation of simple exchange aberrations with a dose-dependence similar to that of a linear quadratic model. CONCLUSIONS: Using a minimal number of assumptions, the kinetics and dose response observed experimentally for DSB rejoining and the formation of simple chromosome exchange aberrations are shown to be consistent with kinetic models based on enzymatic reaction approaches. A non-linear dose response for simple exchange aberrations is possible in a model of recombination of DNA containing a DSB with undamaged DNA when two or more pathways compete for DSB repair.

DNA Damage↗
NASA NTRS1975

High-efficiency graded band-gap Al/x/Ga/1-x/As-GaAs solar cell

A detailed theoretical analysis of an n-on-p graded band-gap Al(x)Ga(1-x)As-GaAs solar cell yields a maximum air mass zero power conversion efficiency of 17% compared to 9% for a similar GaAs cell. The analysis includes surface and bulk minority carrier recombination, junction recombination current, spectrally varying surface reflection, and series resistance loss. The maximum efficiency is determined for a surface recombination velocity of 10,000 cm/sec and hole and electron diffusion lengths of 2.1 and 7.6 microns, respectively. The improved efficiency is primarily due to a built-in electric field, caused by the band-gap gradation, accelerating photogenerated holes toward the p-n junction. This field reduces the surface and bulk recombination of the holes, and thereby enhances their collection.

Hutchby, J. A.↗
NASA NTRS1979

Study of the Effects of Impurities on the Properties of Silicon Materials and Performance of Silicon Solar Cell

Numerical solutions were obtained from the exact one dimensional transmission line circuit model to study the following effects on the terrestrial performance of silicon solar cells: interband Auger recombination; surface recombination at the contact interfaces; enhanced metallic impurity solubility; diffusion profiles; and defect-impurity recombination centers. Thermal recombination parameters of titanium impurity in silicon were estimated from recent experimental data. Based on those parameters, computer model calculations showed that titanium concentration must be kept below 6x10 to the 12th power Ti/cu cm in order to achieve 16% AM1 efficiency in a silicon solar cell of 250 micrometers thick and 1.5 ohm-cm resistivity.

Sah, C. T.↗
NASA NTRS1979

Limiting process in shallow junction solar cells

In extending the violet and nonreflective cell technology to lower resistivities, several processes limiting output power were encountered. The most important was the dark diffusion current due to recombination at the front grid contacts. After removal of this problem by reduction of the silicon metal contact area (to 0.14 percent of the total area), the electric field enhanced junction recombination current J sub r was the main limitation. Alteration of the diffusion profile to reduce the junction field is shown to be an effective means of influencing J sub r. The remaining problems are the bulk recombination in the n+ layer and the surface recombination at the oxide-silicon interface; both of these problems are aggravated by band-narrowing resulting from heavy doping in the diffused layer. Experimental evidence for the main limitations is shown, where increased diffusion temperature is seen to reduce both the influence of the front grid contacts and the junction electric field by increasing the junction depth. The potential for further significant improvement in efficiency appears to be high.

Meulenberg, A.↗
NASA NTRS1981

Microwave plasma generation of hydrogen atoms for rocket propulsion

A flow microwave plasma reaction system is used to study the conversion of hydrogen to hydrogen atoms as a function of pressure, power density, cavity tuning, cavity mode, and time in the plasma zone. Hydrogen atom concentration is measured down-stream from the plasma by NOCl titration. Extensive modeling of the plasma and recombination zones is performed with the plasma zone treated as a backmix reaction system and the recombination zone treated as a plug flow. The thermodynamics and kinetics of the recombination process are examined in detail to provide an understanding of the conversion of recombination energy to gas kinetic energy. It is found that cavity tuning, discharge stability, and optimum power coupling are critically dependent on the system pressure, but nearly independent of the flow rate.

Chapman, R.↗
NASA NTRS1985

Use of low energy hydrogen ion implants in high efficiency crystalline silicon solar cells

This program is a study of the use of low energy hydrogen ion implantation for high efficiency crystalline silicon solar cells. The first quarterly report focuses on two tasks of this program: (1) an examination of the effects of low energy hydrogen implants on surface recombination speed; and (2) an examination of the effects of hydrogen on silicon regrowth and diffusion in silicon. The first part of the project focussed on the measurement of surface properties of hydrogen implanted silicon. Low energy hydrogen ions when bombarded on the silicon surface will create structural damage at the surface, deactivate dopants and introduce recombination centers. At the same time the electrically active centers such as dangling bonds will be passivated by these hydrogen ions. Thus hydrogen is expected to alter properties such as the surface recombination velocity, dopant profiles on the emitter, etc. In this report the surface recombination velocity of a hydrogen emplanted emitter was measured.

Fonash, S. J.↗
NASA NTRS1990

Atomic hydrogen as a launch vehicle propellant

An analysis of several atomic hydrogen launch vehicles was conducted. A discussion of the facilities and the technologies that would be needed for these vehicles is also presented. The Gross Liftoff Weights (GLOW) for two systems were estimated; their specific impulses (I sub sp) were 750 and 1500 lb(sub f)/s/lb(sub m). The atomic hydrogen launch vehicles were also compared to the currently planned Advanced Launch System design concepts. Very significant GLOW reductions of 52 to 58 percent are possible over the Advanced Launch System designs. Applying atomic hydrogen propellants to upper stages was also considered. Very high I(sub sp) (greater than 750 lb(sub f)/s/lb(sub m)) is needed to enable a mass savings over advanced oxygen/hydrogen propulsion. Associated with the potential benefits of high I(sub sp) atomic hydrogen are several challenging problems. Very high magnetic fields are required to maintain the atomic hydrogen in a solid hydrogen matrix. The magnetic field strength was estimated to be 30 kilogauss (3 Tesla). Also the storage temperature of the propellant is 4 K. This very low temperature will require a large refrigeration facility for the launch vehicle. The design considerations for a very high recombination rate for the propellant are also discussed. A recombination rate of 210 cm/s is predicted for atomic hydrogen. This high recombination rate can produce very high acceleration for the launch vehicle. Unique insulation or segmentation to inhibit the propellant may be needed to reduce its recombination rate.

Palaszewski, Bryan A.↗
NASA NTRS1990

An ionic mechanism of carbon formation in flames

The formation of incipient carbon in flames can be described by a series of elementary reactions in which the precursor of soot is the ion C3H3+, and the major building block is acetylene, polyacetylenes, or other hydrocarbon fragments which are present in large concentrations. The precursor ion is produced by nonequilibrium chemi-ionization reactions, e.g., CH asterisk plus C2H2 yields C3H3+ plus e or CH asterisk plus O yields CHO+ plus e. The CHO+ rapidly becomes C3H3+ through a series of ion-molecule reactions. The chemi-ion then adds acetylene in a series of very rapid ion-molecule reactions producing larger and larger ions. Ions isomerize very rapidly to produce aromatic structures overcoming one of the major problems with neutral species mechanisms: how to form the first carbon ring. As the ions grow, their recombination rate coefficients with electrons increase so that the larger ions are removed by dissociative recombination. These neutral species now continue to grow by the addition of more acetylene producing even larger neutral species. With increasing size, the rate coefficient of electron attachment also increases causing the reaction to become important, depending upon the temperature. Appreciable concentrations of negative ions shift the ion removal process to dissociative ion-ion recombination, which is orders of magnitude slower than ion-electron recombination. As the neutral species continue to grow by the addition of acetylene, they gradually take on the aspect of particles, i.e., the bulk properties of the substance CxHy dominate over the chemical properties. This change is gradual and there is no distinct size at which a large molecule becomes a particle. Evidence will be presented supporting the above mechanism. All of the ions proposed in the mechanism have been observed by mass spectrometric analysis, their concentrations measured, and their rates of reaction in the flame environment determined to be adequate to account for the observed rate of formation of carbon.

Calcote, H. F.↗
NASA NTRS1990

Atomic hydrogen as a launch vehicle propellant

An analysis of several atomic hydrogen launch vehicles was conducted. A discussion of the facilities and the technologies that would be needed for these vehicles is also presented. The Gross Liftoff Weights (GLOW) for two systems were estimated; their specific impulses (I sub sp) were 750 and 1500 lb (sub f)/s/lb(sub m). The atomic hydrogen launch vehicles were also compared to the currently planned Advanced Launch System design concepts. Very significant GLOW reductions of 52 to 58 percent are possible over the Advanced Launch System designs. Applying atomic hydrogen propellants to upper stages was also considered. Very high I(sub sp) (greater than 750 1b(sub f)/s/lb(sub m) is needed to enable a mass savings over advanced oxygen/hydrogen propulsion. Associated with the potential benefits of high I(sub sp) atomic hydrogen are several challenging problems. Very high magnetic fields are required to maintain the atomic hydrogen in a solid kilogauss (3 Tesla). Also the storage temperature of the propellant is 4 K. This very low temperature will require a large refrigeration facility for the launch vehicle. The design considerations for a very high recombination rate for the propellant are also discussed. A recombination rate of 210 cm/s is predicted for atomic hydrogen. This high recombination rate can produce very high acceleration for the launch vehicle. Unique insulation or segmentation to inhibit the propellant may be needed to reduce its recombination rate.

Palaszewski, Bryan A.↗
NASA NTRS1993

Performance assessment of low pressure nuclear thermal propulsion

A low pressure nuclear thermal propulsion (LPNTP) system, which takes advantage of hydrogen dissociation/recombination, was proposed as a means of increasing engine specific impulse (Isp). The effect of hydrogen dissociation/recombination on LPNTP Isp is examined. A two-dimensional computer model was used to show that the optimum chamber pressure is approximately 100 psia (at a chamber temperature of 3,000 K), with an Isp approximately 15 s higher than at 1,000 psia. At high chamber temperatures and low chamber pressures, the increase in Isp is due to both lower average molecular weights caused by dissociation and added kinetic energy from monatomic hydrogen recombination. Monatomic hydrogen recombination increases the Isp more then hydrogen dissociation. Variations in the mole fraction of monatomic hydrogen are similar to variations in static pressure along the axial nozzle position. Most recombination occurs close to the nozzle throat. Practical variations in nozzle geometry have minimal impact on recombination. Other models which can simulate a wider range of nozzle designs should be used in the future. The uncertainty of the hydrogen kinetic reaction rates at high temperatures (approximately 3,000 K) affects the accuracy of the analysis and should be verified with simple bench tests.

Gerrish, H. P., Jr.↗
NASA NTRS1993

Performance assessment of low pressure nuclear thermal propulsion

An increase in Isp for nuclear thermal propulsion systems is desirable for reducing the propellant requirements and cost of future applications, such as the Mars Transfer Vehicle. Several previous design studies have suggested that the Isp could be increased substantially with hydrogen dissociation/recombination. Hydrogen molecules (H2), at high temperatures and low pressures, will dissociate to monatomic hydrogen (H). The reverse process (i.e., formation of H2 from H) is exothermic. The exothermic energy in a nozzle increases the kinetic energy and therefore, increases the Isp. The low pressure nuclear thermal propulsion system (LPNTP) system is expected to maximize the hydrogen dissociation/recombination and Isp by operating at high chamber temperatures and low chamber pressures. The process involves hydrogen flow through a high temperature, low pressure fission reactor, and out a nozzle. The high temperature (approximately 3000 K) of the hydrogen in the reactor is limited by the temperature limits of the reactor material. The minimum chamber pressure is about 1 atm because lower pressures decrease the engines thrust to weight ratio below acceptable limits. This study assumes that hydrogen leaves the reactor and enters the nozzle at the 3000 K equilibrium dissociation level. Hydrogen dissociation in the reactor does not affect LPNTP performance like dissociation in traditional chemical propulsion systems, because energy from the reactor resupplies energy lost due to hydrogen dissociation. Recombination takes place in the nozzle due primarily to a drop in temperature as the Mach number increases. However, as the Mach number increases beyond the nozzle throat, the static pressure and density of the flow decreases and minimizes the recombination. The ideal LPNTP Isp at 3000 K and 10 psia is 1160 seconds due to the added energy from fast recombination rates. The actual Isp depends on the finite kinetic reaction rates which affect the amount of monatomic hydrogen recombination before the flow exits the nozzle. A LPNTP system has other technical issues (e.g. flow instability and two-phase flow) besides hydrogen dissociation/recombination which affect the systems practicality. In this study, only the effects of hydrogen dissociation/recombination are examined.

Gerrish, Harrold P., Jr.↗
NASA NTRS1997

The Effect of Diffusional Transport and Surface Catalysis on the Aerothermodynamic Heating for Martian Atmospheric Entry

For the reentry heating of 70-degree blunt sphere-cones entering Mars at velocities in excess of 6 km/sec, a study was performed to determine the magnitude of both convective and catalytic heating on the cone forebody. Case studies of the peak heating conditions for the current NASA Mars Pathfinder entry probe, as well as the peak heating conditions of the proposed NASA Mars 2001 aerobraking orbiter mission were performed. Since the actual behavior of the chemical recombination of Mars atmosphere hypersonic shock layer species on heat shield materials is not known, and no experimental studies of any consequence have been done to determine surface reaction rates for the CO2 system, a parametric analysis of various reaction schemes and surface catalytic mechanistic models was performed. In many cases the actual Mars entry probe will have a heat shield composed of an ablative material which can either partially or completely preclude the existence of catalytic surface recombination phenomena. The extent of this blockage effect has not been examined at this time and is not considered in this effort. Instead only non-ablative computations are performed to separately evaluate the full extent of the surface catalysis and related diffusional phenomena. Parametric studies include peak heating point comparisons of non-catalytic, partially catalytic and fully catalytic total surface heat transfer for three difference surface recombination catalytic mechanisms (with and without simultaneous CO + O and O + O recombination) as well as with different species diffusion models. Diffusion model studies include constant Schmidt number (equal diffusivities) and the bifurcation, approximate multi-component diffusion model. Since the gas phase reaction kinetics for the Mars CO2 based atmosphere have also not been validated, the effect of two different (fast and slow) sets of gas kinetics on heat transfer is presented.

Henline, William D.↗
NASA NTRS2003

Molecular Carbon in the Galaxy: Laboratory and Observational Studies

In a collaboration with the Mats Larsson group from Stockholm, we carried out a new measurement of the rate of dissociative recombination of H(sup *, sub j), using a new pulsed supersonic beam source of rotationally cold H(sup *, sub j). This source was first designed and characterized in our lab by IR cavity ringdown spectroscopy, determining a rotationaYtranslationa1 temperature of 20-60K, depending on conditions. This new source was then taken to Stockholm for the recombination rate studies at the CRYRING storage ring. The recombination rate constant measured against temperature yields values consistent with the most recent calculations, whereas previous experimental measurements varied over a range of 10(exp 4) and were poor agreement with theory. This is a crucial achievement for understanding the ion chemistry of diffuse clouds. Moreover, this result in combination with recent observations implies a greatly enhanced (factor of 40) cosmic ray ionization rate in a diffuse cloud (zeta Persei) relative to previous studies. The implications of this are discussed in our recent Nature paper. An enhanced cosmic-ray flux towards zeta Persei inferred from a laboratory study of the H(sup *, sub j)-e(sup -) recombination rate.

Saykally, Richard James↗
NASA NTRS2002

Momentum and Heat Flux Measurements in the Exhaust of VASIMR Using Helium Propellant

Electromagnetic thrusters typically use electric and magnetic fields to accelerate and exhaust plasma through interactions with the charged particles in the plasma. The energy required to create the plasma, i.e. ionization energy, is potential energy between the electron and ion. This potential energy is typically lost since it is not recovered as the plasma is exhausted and is known as frozen flow loss. If the frozen flow energy is a small fraction of the total plasma energy, this frozen flow loss may be negligible. However, if the frozen flow energy is a major fraction of the total plasma energy, this loss can severely reduce the energy efficiency of the thruster. Recovery and utilization of this frozen flow energy can improve the energy efficiency of a thruster during low specific impulse operating regimes when the ionization energy is a large fraction of the total plasma energy. This paper quantifies the recovery of the frozen flow energy, i.e. recombination energy, via the process of surface recombination for helium. To accomplish this task the momentum flux and heat flux of the plasma flow were measured and compared to calculated values from electrostatic probe data. This information was used to deduce the contribution of recombination energy to the total heat flux on a flat plate as well as to characterize the plasma conditions. Helium propellant was investigated initially due to its high ionization potential and hence available recombination energy.

Chavers, D. Gregory↗