Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PLASMA DENSITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

Effect of Density Irregularities on Radio Frequency Wave Propagation in Ionospheric Plasmas

Density irregularities play a vital role in determining how radio frequency (RF) waves travel through plasmas. In the Earth’s ionosphere, these density irregularities also impact radio communication. In this study, we conduct a detailed numerical analysis of RF wave propagation in small-scale ionospheric density irregularities using the advanced Petra-M code. We focus specifically on high-frequency (HF) waves, ranging from 3 to 30 MHz, which are essential for military, amateur radio operators, and emergency communications. By introducing density structures, such as equatorial plasma bubbles derived from fluid simulations, we demonstrate that HF waves can scatter in multiple directions when they encounter these irregularities. Additionally, we observe significant mode conversion, where incoming electromagnetic waves transform into electrostatic modes within the density gradient layer. This shows that smaller density irregularities can greatly weaken signals or cause complete signal loss for receivers, emphasizing the need for increased awareness and innovative solutions in radio communication transmission.

Kim, Eun-Hwa [Princeton Plasma Physics Laboratory ↗

Toroidal Alfvén mode instability driven by plasma current in low-density Ohmic plasmas of the spherical tori

Due to intrinsically low magnetic fields, at low density the drift speed of the current-carrying electrons in spherical tokamaks can exceed fraction of the Alfvén speed sufficient for the excitation of the Alfvén gap modes. A particular case of the toroidal mode, observed during minor disruptions in Ohmic shots on SUNIST [Liu et al., Phys. Plasmas 23, 120706 (2016)], is considered in the present communication. Due to the negligible effect of the electron pressure gradient, the growth rate scales linearly with the drift speed, with slope inversely proportional to electron thermal velocity. In the absence of continuum damping, the threshold value of the drift speed for TAE excitation is independent of electron temperature.

Marchenko, V. S. (ORCID:0000000261480533)↗

Ground-Based Simulation of Low-Earth Orbit Plasma Conditions: Plasma Generation and Characterization

A 16-cm diameter plasma source operated on argon is described that is capable of producing a plasma environment that closely simulates the low Earth orbit (LEO) conditions experienced by satellites in the altitude range between 300 to 500 km. The plasma source uses a transverse-field magnetic filter, and has been successful in producing low electron temperature plasmas that contain streaming ion populations. Both of these characteristics are important because the plasma in LEO is relatively cold (e.g., Te approx. 0.1 eV) and the ram energy of the ions due to the motion of the satellite relative to the LEO plasma is high (e.g., 7,800 m/s which corresponds to approx. 5 eV for O+ ions). Plasma source operational conditions of flow rate and discharge power are presented that allow the electron temperature to be adjusted over a range from 0.14 to 0.4 eV. The expanding plasma flow field downstream of the source contains both low-energy, charge-exchange ions and streaming ions with energies that are adjustable over a range from 4 eV to 6 eV. At low flow rates and low facility pressures, the streaming ion component of the ion population comprises over 90% of the total plasma density. In the work described herein, a large area retarding potential analyzer was used to measure both electron and ion energy distribution functions in the low density, expanding plasma produced downstream of the plasma source. The benefits of using this type of plasma diagnostic tool in easily perturbed, low-density plasma are identified, and techniques are also discussed that can be used to perform real-time measurements of electron temperature. Finally, recommendations are made that may enable lower electron temperatures to be produced while simultaneously decreasing the plasma source flow rate below 1 to 2 sccm.

Williams, John D.↗

Effect of antenna capacitance on the plasma characteristics of an internal linear inductively coupled plasma system

This study examined the effect of the antenna capacitance of an inductively coupled plasma (ICP) source, which was varied using an internal linear antenna, on the electrical and plasma characteristics of the ICP source. The inductive coupling at a given rf current increased with decreasing antenna capacitance. This was caused by a decrease in the inner copper diameter of the antenna made from coaxial copper/quartz tubing, which resulted in a higher plasma density and lower plasma potential. By decreasing the diameter of the copper tube from 25 to 10 mm, the plasma density of a plasma source size of 2750x2350 mm{sup 2} was increased from approximately 8x10{sup 10}/cm{sup 3} to 1.5x10{sup 11}/cm{sup 3} at 15 mTorr Ar and 9 kW of rf power.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Proton Bunch Self-Modulation in Plasma with Density Gradient

We study experimentally the effect of linear plasma density gradients on the self-modulation of a 400 GeV proton bunch. Results show that a positive or negative gradient increases or decreases the number of microbunches and the relative charge per microbunch observed after 10 m of plasma. The measured modulation frequency also increases or decreases. With the largest positive gradient we observe two frequencies in the modulation power spectrum. Results are consistent with changes in wakefields’ phase velocity due to plasma density gradients adding to the slow wakefields’ phase velocity during self-modulation growth predicted by linear theory.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The generation mechanism for magnetosheath lion roars

The origin of lion roars, intense electromagnetic whistler-mode waves which occur throughout the magnetosheath, is investigated based on particle and field data obtained on the ISEE satellites. Analysis of the measured magnetic fields, plasma densities and plasma wave intensities during periods of lion roar emission reveals the lion roar bursts to be correlated with decreases in magnetic field intensity, while the plasma density exhibits a strong anticorrelation with the magnetic field variability during the bursts and the total plasma pressure remains essentially constant. Results indicate that the waves can originate by the cyclotron resonant instability with anisotropic magnetosheath electrons whenever the magnetic energy per particle falls to values comparable with the electron thermal energy. Variations in the magnetic energy appear to be associated with the hydromagnetic mirror instability which in turn is excited by a pressure anisotropy in the magnetosheath ion population.

Thorne, R. M.↗

Is the bulk mode conversion important in high density helicon plasma?

In a high-density helicon plasma production process, a contribution of Trivelpiece-Gould (TG) wave for surface power deposition is widely accepted. The TG wave can be excited either due to an abrupt density gradient near the plasma edge (surface conversion) or due to linear mode conversion from the helicon wave in a density gradient in the bulk region (bulk mode conversion). By numerically solving the boundary value problem of linear coupling between the helicon and the TG waves in a background with density gradient, we show that the efficiency of the bulk mode conversion strongly depends on the dissipation included in the plasma, and the bulk mode conversion is important when the dissipation is small. Also, by performing FDTD simulation, we show the time evolution of energy flux associated with the helicon and the TG waves.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Calculation and Analysis of Electrophysical Processes in a High-Power Plasma Accelerator with an Intrinsic Magnetic Field

We have considered basic theoretical models describing various aspects of the formation and acceleration of plasma in pulsed accelerators. The discharge current, magnetic field, and plasma bunch velocity have been determined experimentally at different initial gas pressures in the accelerator chamber. We have considered the correspondence of some theoretical models of plasma acceleration to experimental data obtained in a KPU-30 coaxial accelerator. It is shown that the formation of the plasma in the coaxial accelerator depends on the plasma density, and acceleration processes at densities higher and lower than a certain transient density value on the order of 10{sup 11}–10{sup 12} cm{sup –3} are different. At a density higher than this critical value, the plasma is accelerated by a magnetic force. At the same time, at a low plasma density, plasma can be accelerated by an internal electric field.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Quadruple Langmuir probe characterization of different fuel gases in a plasma deflagration accelerator

Astrophysical flows may be studied by reproducing similar conditions using a coaxial plasma accelerator operating in the deflagration regime (or plasma deflagration accelerator). This allows for the recreation and investigation of dynamics present in complex highly coupled plasma systems at the laboratory scale. Here we report on measurements of the plasma density, temperature, plasma potential and velocity found using a quadruple Langmuir probe (QLP) on such a deflagration accelerator in the form of the Stanford Coaxial High ENerGy (CHENG) device operating with multiple gases – specifically argon, nitrogen and hydrogen. Experiments show a general decrease in bulk plasma velocity with gas atomic mass from upwards of 120 km s –1 with hydrogen to less than 30 km s –1 with argon. There was an accompanying increase in peak plasma density with increasing atomic mass from ~3 × 10 20 m –3 with hydrogen to ~1.5 × 10 21 m –3 with argon. It was found that the momentum flux and internal energy density also generally increase with atomic mass while the particle flux is constant between shots. Further investigation is needed to understand these correlations and the underlying physics. Lastly, comparisons with scaling laws show that while the CHENG device may be operated in such a way as to simulate the effects of bulk solar wind movement, it may not properly capture the thermal effects.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Electron cyclotron emission measurements and modeling in optically semi-transparent plasma on the HSX stellarator

On the Helically Symmetric Experiment (HSX), electron cyclotron emission (ECE) at the second harmonic of the electron gyrofrequency is measured with a 16-channel heterodyne receiver. An ECE radiometer diagnostic has been calibrated with a broadband frequency source, allowing independent measurements of the electron temperature. The antenna pattern has a significant impact on the measurements, and modeling its effect is necessary to produce an ECE radiation temperature spectrum. Measurements, calibration results, and modeling of the ECE data are presented in this paper. At a relatively high plasma density, HSX plasmas are thermal, and the radiation temperature measured by the radiometer is in good agreement with the electron temperature measured by a Thomson scattering diagnostic. At a relatively low plasma density, the deviation from a Maxwellian distribution is large, and asymmetry in the radiation temperature profile is measured. These measurements are supported by single-pass and multi-pass ray tracing calculations of the electron cyclotron emission using the TRAVIS ray tracing code. Thermal and nonthermal electron populations exist in HSX, and the effect of these populations on the asymmetry in the measured emission is presented.

Cyclotron radiation↗

Multi-dimensional collective effects in high-current relativistic beams relevant to High Density Laboratory Plasmas

In summary, an analytical model describing the self-pinching of a relativistic charge-neutralized electron beam undergoing the collisionless Weibel instability in an overdense plasma has been developed. The model accurately predicts the final temperature and size of the self-focused filament. It is found that the final temperature is primarily defined by the total beam’s current, while the filament’s radius is shown to be smaller than the collisionless skin depth in the plasma and primarily determined by the beam’s initial size. The model also accurately predicts the repartitioning ratio of the initial energy of the beam’s forward motion into the magnetic field energy and the kinetic energy of the surrounding plasma. The density profile of the final filament is shown to be a superposition of the standard Bennett pinch profile and a wide halo surrounding the pinch, which contains a significant fraction of the beam’s electrons. PIC simulations confirm the key assumption of the analytic theory: the collisionless merger of multiple current filaments in the course of the Weibel Instability provides the mechanism for Maxwellization of the beam’s distribution function. Deviations from the Maxwell-Boltzmann distribution are explained by incomplete thermalization of the deeply trapped and halo electrons. It is conjectured that the simple expression derived here can be used for understanding collsionless shock acceleration and magnetic field amplification in astrophysical plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Input impedance of a powerful single-core ferromagnetic inductively coupled plasma source

An experimental study of the recently developed version of the ferromagnetic inductively coupled plasma source has shown that under certain circumstances its input impedance becomes almost independent of the delivered rf driving power and (therefore) of the produced plasma density. This plasma source consists of a large ferromagnetic core, which is fully immersed in plasma. This core is surrounded by a primary winding and plasma appears due to gas discharge driven by an rf voltage applied to this primary winding. We have found values of parameters which determine the input impedance in such an ''independent'' regime and derived a quantitative theory which is in good agreement with the measured impedance values.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Time-Domain Simulation of RF Couplers

We have developed a finite-difference time-domain (FDTD) fluid-like approach to integrated plasma-and-coupler simulation [1], and show how it can be used to model LH and ICRF couplers in the MST and larger tokamaks.[2] This approach permits very accurate 3-D representation of coupler geometry, and easily includes non-axi-symmetry in vessel wall, magnetic equilibrium, and plasma density. The plasma is integrated with the FDTD Maxwell solver in an implicit solve that steps over electron time-scales, and permits tenuous plasma in the coupler itself, without any need to distinguish or interface between different regions of vacuum and/or plasma. The FDTD algorithm is also generalized to incorporate a time-domain sheath potential [3] on metal structures within the simulation, to look for situations where the sheath potential might generate local sputtering opportunities. Benchmarking of the time-domain sheath algorithm has been reported in the references. Finally, the time-domain software [4] permits the use of particles, either as field diagnostic (test particles) or to self-consistently compute plasma current from the applied RF power.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Progress towards a practical multicell positron trap

Described here is progress in an experimental program to develop a 21 cell multicell trap for the accumulation and storage of {approx} 10{sup 12} positrons. The basic architecture is an arrangement of multiple Penning-Malmberg (PM) trapped plasmas (i.e., cells) arranged in parallel in a common vacuum system and magnetic field. Experiments are described that are intended to address several key issues, including the effects of large space charge potentials and high plasma densities on: plasma heating, deterioration of confinement, and decreased efficiency of rotating electric fields in producing plasma compression. The confinement of PM plasmas displaced both radially and toward the ends of the uniform magnetic field region will also be investigated.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Particle-in-cell simulations of collisionless magnetic reconnection with a non-uniform guide field

Results are presented of a first study of collisionless magnetic reconnection starting from a recently found exact nonlinear force-free Vlasov–Maxwell equilibrium. The initial state has a Harris sheet magnetic field profile in one direction and a non-uniform guide field in a second direction, resulting in a spatially constant magnetic field strength as well as a constant initial plasma density and plasma pressure. It is found that the reconnection process initially resembles guide field reconnection, but that a gradual transition to anti-parallel reconnection happens as the system evolves. The time evolution of a number of plasma parameters is investigated, and the results are compared with simulations starting from a Harris sheet equilibrium and a Harris sheet plus constant guide field equilibrium.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Effect of radial plasma transport at the magnetic throat on axial ion beam formation

Correlation between radial plasma transport and formation of an axial ion beam has been investigated in a helicon plasma reactor implemented with a convergent-divergent magnetic nozzle. The plasma discharge is sustained under a high magnetic field mode and a low magnetic field mode for which the electron energy probability function, the plasma density, the plasma potential, and the electron temperature are measured at the magnetic throat, and the two field modes show different radial parametric behaviors. Although an axial potential drop occurs in the plasma source for both field modes, an ion beam is only observed in the high field mode while not in the low field mode. The transport of energetic ions is characterized downstream of the plasma source using the delimited ion current and nonlocal ion current. A decay of ion beam strength is also observed in the diffusion chamber.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Laser-driven plasma beat-wave propagation in a density-modulated plasma

A laser-driven plasma beat wave, propagating through a plasma with a periodic density modulation, can generate two sideband plasma waves. One sideband moves with a smaller phase velocity than the pump plasma wave and the other propagates with a larger phase velocity. The plasma beat wave with a smaller phase velocity can accelerate modest-energy electrons to gain substantial energy and the electrons are further accelerated by the main plasma wave. The large phase velocity plasma wave can accelerate these electrons to higher energies. As a result, the electrons can attain high energies during the acceleration by the plasma waves in the presence of a periodic density modulation. The analytical results are compared with particle-in-cell simulations and are found to be in reasonable agreement.

07 ISOTOPE AND RADIATION SOURCES↗

Observation of low magnetic field density peaks in helicon plasma

Single density peak has been commonly observed in low magnetic field (<100 G) helicon discharges. In this paper, we report the observations of multiple density peaks in low magnetic field (<100 G) helicon discharges produced in the linear helicon plasma device [Barada et al., Rev. Sci. Instrum. 83, 063501 (2012)]. Experiments are carried out using argon gas with m = +1 right helical antenna operating at 13.56 MHz by varying the magnetic field from 0 G to 100 G. The plasma density varies with varying the magnetic field at constant input power and gas pressure and reaches to its peak value at a magnetic field value of {approx}25 G. Another peak of smaller magnitude in density has been observed near 50 G. Measurement of amplitude and phase of the axial component of the wave using magnetic probes for two magnetic field values corresponding to the observed density peaks indicated the existence of radial modes. Measured parallel wave number together with the estimated perpendicular wave number suggests oblique mode propagation of helicon waves along the resonance cone boundary for these magnetic field values. Further, the observations of larger floating potential fluctuations measured with Langmuir probes at those magnetic field values indicate that near resonance cone boundary; these electrostatic fluctuations take energy from helicon wave and dump power to the plasma causing density peaks.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗