Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Microstructure formation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Passivation and alloying element retention in gas atomized powders

A method for gas atomization of a titanium alloy, nickel alloy, or other alumina (Al 2 O 3 )-forming alloy wherein the atomized particles are exposed as they solidify and cool in a very short time to multiple gaseous reactive agents for the in-situ formation of a passivation reaction film on the atomized particles wherein the reaction film retains a precursor halogen alloying element that is subsequently introduced into a microstructure formed by subsequent thermally processing of the atomized particles to improve oxidation resistance.

Heidloff, Andrew J.↗
DOE OSTI2023

The effects of carbonaceous inclusions and their distributions on dynamic failure processes in boron carbide ceramics

Commercially available boron carbide ceramics typically have heterogeneous microstructures that contain distributions of processing-induced inclusions. The inclusions that are rich in carbon (i.e., carbonaceous) govern the underlying mechanisms of brittle fracture through wing crack formation, and thus dictate the mechanical response of the ceramic. In this study, we investigate the dynamic failure of five boron carbide ceramic materials with different inclusion populations. All of the materials were prepared by hot-pressing; four of these boron carbides contained different sizes and concentrations of carbonaceous inclusions, while one contained no carbonaceous inclusions. The heterogeneity distributions were characterized in some detail for statistical analysis using scanning electron microscopy and quantitative image analysis. A modified compression Kolsky bar setup with in situ ultra-high-speed microscopic imaging (10 million frames per second) was then used to study the influence of the inclusion distributions on the dynamic failure processes in these materials, at nominal high strain rates of 10 2 -10 3 s -1 . The in situ ultra-high-speed microscopy highlighted the link between micro and macroscale failure processes and demonstrated that the carbonaceous inclusions are indeed the preferential sites for nucleation of wing cracks, as previously hypothesized based on post-mortem observations. The relative orientation of an inclusion with respect to the compression axis was shown to affect the likelihood that it would participate in crack nucleation. In conclusion, all of the ceramics were also found to have orientation-dependent peak compressive stress, regardless of the presence of carbonaceous inclusions, suggesting that grain orientation distributions are also important.

36 MATERIALS SCIENCE↗
DOE OSTI2025

A novel microstructural approach for TRIP/TWIP β-Ti alloys using intermetallic precipitation

Interest in metastable β-Ti has grown, due to the exceptional work hardening caused by TRansformation and TWinning Induced Plasticity (TRIP/TWIP). A current challenge is increasing the yield strength, while maintaining the benefits of TRIP/TWIP. This study presents the first report of TRIP/TWIP in a metastable β-Ti alloy containing intermetallic compounds, specifically Ti silicide precipitates. Silicon (Si) additions enable the formation of silicide particles, which can be precipitated, dissolved, and controlled through tailored heat treatments. In-situ synchrotron x-ray diffraction during tensile testing reveals primary {332}<113> twinning activates first, followed by TRIP, leading to extensive work hardening and uniform elongation in the solutionized state. In conclusion, these findings open a novel microstructural approach to the design of multiphase TRIP/TWIP titanium alloys, relying on intermetallic precipitation rather than allotropes such as α or ω phase, and lay the groundwork for future studies on intermetallic precipitation strengthening.

Materials science↗
DOE OSTI2023

Microstructure and high temperature properties of tungsten processed via electron beam melting additive manufacturing

There is considerable interest in the adoption of additive manufacturing for processing refractory metals. The layer-wise fabrication approach enables opportunities for producing complex geometries which cannot be otherwise be achieved via powder metallurgy. However, the processing science is still in its nascent stages and structure–property relations are relatively unexplored. Fundamental research is needed to further develop the technology and enable the fabrication of refractory metals for high temperature applications. Here we focus on the processing of pure tungsten using electron beam melting additive manufacturing. Experimentally we develop a suitable processing window for achieving high density crack free material. Microstructural analysis reveals that the microstructure generally consists of a columnar structure with a (111) build direction fiber preference, although, fiber switching was observed. Process induced deformation is believed to drive the formation of subgrains whose boundaries exhibit a high dislocation density. Additionally, high temperature tensile testing reveals that the material exhibits excellent properties closer to that of annealed tungsten. Significant mechanical anisotropy was observed to be present which is likely driven by strong crystallographic texture.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Conversion of real-world aluminum scrap streams into high-performance Al–Mg–Si–Cu automotive alloys using shear assisted processing and extrusion

The conversion of post-consumer aluminum (Al) scrap into usable Al alloys without adding primary Al is challenging because of excess impurities. In this work, >99% post-consumer Twitch, used beverage cans (UBCs), and remelt scrap ingots (RSIs) were used as feedstock materials. As-cast and solution heat-treated feedstock billets were extruded using Shear Assisted Processing and Extrusion (ShAPE) at ~510°C, followed by press quenching. To explore the development of the microstructure, texture, and underlying mechanisms and how they contribute to the overall strengthening in as-extruded and artificially aged samples, scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD) were used to collect microstructure and texture data. The enhanced strength and ductility were corroborated with the microstructural features and crystallographic texture. Simple shear $\textrm{A}/\bar{\textrm{A}}$, $\textrm{A}_1^*/\textrm{A} _2^*$ texture components along with weak $\textrm{C}$ and $\textrm{B}/\bar{\textrm{B}}$ texture components were formed during extrusion; the texture was strengthened after heat treatment. The refined second-phase particles helped to retain the deformed microstructure and texture. The contributions of dislocation and precipitate strengthening were maximized when billets were solution-heat-treated prior to extrusion. This is attributed to the formation of effective supersaturated solid solutions during the ShAPE process, which precipitate out during the peak age treatment. Overall, the highest yield strength of 305 MPa, ultimate tensile strength of 350 MPa, and elongation of 12% were achieved in artificially aged samples, which are comparable to those of Al 6082-T6.

Al alloy↗
DOE OSTI2020

Nanoscale Engineering of Polymorphism in Cu 2 Se-Based Composites

Crystal polymorphism selection during synthesis is extremely challenging. However, promoting the formation of a specific metastable polymorph enables modulation of the functional properties of phase-change materials through alteration of the relative abundance of various polymorphs. Here, we demonstrate the stabilization of the superionic β-Cu 2 Se phase under ambient conditions and the direct control over the relative ratio between the α-Cu 2 Se and β-Cu 2 Se polymorphs in (x)CuGaSe 2 /(1-x)Cu 2 Se composites using CuGaSe 2 nanoseeds. Here, we found that the small lattice mismatch between β-Cu 2 Se (cubic) and the ab plane of tetragonal CuGaSe 2 nanoseeds promotes the formation of low-energy coherent CuGaSe 2 /β-Cu 2 Se interfaces leading to preferential stabilization of β-Cu 2 Se. Astonishingly, the hierarchical microstructure of the resulting composites enables a remarkable decoupling of charge and heat transport, which is manifested by a breakdown of the Wiedemann-Franz law

36 MATERIALS SCIENCE↗
DOE OSTI2023

Effects of transition metal carbide dispersoids on helium bubble formation in dispersion-strengthened tungsten

Abstract The formation of helium bubbles and subsequent property degradation poses a significant challenge to tungsten as a plasma-facing material in future long-pulse plasma-burning fusion reactors. In this study, we investigated helium bubble formation in dispersion-strengthened tungsten doped with transition metal carbides, including TaC, ZrC, and TiC. Of the three dispersoids, TaC exhibited the highest resistance to helium bubble formation, possibly due to the low vacancy mobility in the Group VB metal carbide and oxide phases. Under identical irradiation conditions, large helium bubbles formed at grain boundaries in tungsten, while no bubbles were observed at the interfaces between the carbide dispersoid and tungsten matrix. Moreover, our results showed the interfaces could suppress helium bubble formation in the nearby tungsten matrix, suggesting that the interfaces are more effective in trapping helium as tiny clusters. Our research provided new insights into optimizing the microstructure of dispersion-strengthened tungsten alloys to enhance their performance.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Accelerated oxidation during 1350°C cycling of ytterbium silicate environmental barrier coatings

We report environmental barrier coatings (EBCs) will be needed to protect SiC-based ceramic matrix composite components for the next generation of high-efficiency industrial gas turbines (IGTs). The IGT application will require ≥25 kh lifetimes, and little data are available on EBC failure mechanisms, particularly at ≥1300°C. Initial 1-h furnace cycle testing at 1350°C in 90 vol% H 2 O/10 vol% air was conducted ≥1000 cycles on thermally sprayed ytterbium disilicate (YbDS) coatings with and without an Si bond coating. By ≥1000 h, both EBCs formed thick, highly cracked, and fully crystalline cristobalite scales. Comparison of thermally grown oxide (TGO) microstructure and kinetics to isothermal rates of Si and SiC steam oxidation indicated a departure from slow-growing parabolic growth to more rapid rates of silica formation. Possible mechanisms and implications for this acceleration are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2023

In situ probing of interfacial roughness and transient phases during ceramic cold sintering process

The ceramic cold sintering process (CSP) offers an eco-friendly approach to producing fully dense ceramics at low temperatures. However, an incomplete mechanistic understanding hinders its optimization and widespread adoption. In this study, we analyze the microstructural and structural changes in ZnO, a model CSP system, using in situ synchrotron-based high-energy small-angle X-ray scattering and X-ray diffraction techniques. Our results reveal the time evolution of ZnO particles' surface area and roughness, reflecting the dissolution and re precipitation processes that enable densification. The in situ measurements supply valuable kinetic data for these stages of CSP. Alongside microstructural changes and densification, we observed the evolution of secondary phases representing reaction products between ZnO and acetic acid, the solvent used. The initial ZnO/solvent mixture's dominant secondary phase is attributed to zinc acetate, which is gradually replaced by a zinc soap-type structure during CSP. This structure has a large (≈ 21 Å) lattice parameter and is assumed to have a layered nature. The formation of this soap phase, which is retained in the sintered product as an intergranular component, appears to be a signature of successful cold sintering as it facilitates mass transport, leading to densification. Here, our study underscores the potential of in situ synchrotron characterization for revealing microstructural and phase-evolution details during CSP. These findings, which would be challenging to obtain through ex situ measurements, provide crucial data to guide and validate theoretical models, ultimately enhancing CSP's effectiveness and adoption.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Microstructural Evaluation of Phase Instability in Large Bandgap Metal Halide Perovskites

The optoelectronic performance of organic–inorganic halide perovskite (OIHP)-based devices has been improved in recent years. Particularly, solar cells fabricated using mixed-cations and mixed-halides have outperformed their single-cation and single-halide counterparts. Yet, a systematic evaluation of the microstructural behavior of mixed perovskites is missing despite their known composition-dependent photoinstability. Here, we explore microstructural inhomogeneity in (FAPbI 3 ) x (MAPbBr 3 ) 1– x using advanced scanning probe microscopy techniques. In this work, contact potential difference (CPD) maps measured by Kelvin probe force microscopy show an increased fraction of grains exhibiting a low CPD with flat topography as MAPbBr 3 concentration is increased. The higher portion of low CPD contributes to asymmetric CPD distribution curves. Chemical analysis reveals these grains being rich in MA, Pb, and I. The composition-dependent phase segregation upon illumination, reflected on the emergence of a low-energy peak emission in the original photoluminescence spectra, arises from the formation of such grains with flat topology. Bias-dependent piezo-response force microscopy measurements, in these grains, further confirm vigorous ion migration and cause a hysteretic piezo-response. Our results, therefore, provide insights into the microstructural evaluation of phase segregation and ion migration in OIHPs pointing toward process optimization as a mean to further enhance their optoelectronic performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Supercritical, liquid, and gas CO 2 reactive transport and carbonate formation in portland cement mortar

In this paper, we investigate carbonate formation and reactive transport rate in variably saturated portland cement mortars when high concentrations of gas, liquid, or supercritical CO 2 flow through their pore network. Xray computed tomography completed during CO 2 flow is used to quantify the microstructural evolution as the mortar carbonates. After in situ tests, higher resolution scans, thermogravimetric analysis, and desorption isotherm analysis are performed to further quantify microstructural changes. We found that at dry conditions supercritical CO 2 moves more rapidly through the pore space and precipitates more carbonates than liquid or gas CO 2 . However, at 50% degree of saturation (DOS) the CO 2 state did not affect the rate of transport in that each specimen exposed to a different CO 2 state carbonated within the first hour of CO 2 exposure. When the pore space is at 50 or 100% DOS, supercritical CO 2 did not react with hydration products more rapidly nor did it result in more carbonate formation during exposure compared to gas or liquid CO 2 . The amount of Ca(OH) 2 that contributes to CaCO 3 formation is correlated to the DOS. For the mortar composition analyzed, Ca(OH) 2 contributes to approximately 40% of the carbonates formed in the 50% DOS specimens and 15% in the 100% DOS specimens. In other words, as the amount of moisture in the pore space increases, phases other than Ca(OH) 2 contribute to more than 50% of the total CaCO 3 formed.

42 ENGINEERING↗
DOE OSTI2023

Atomic force microscopy and scanning electron microscopy characterization of the controlling of surface morphology of epoxy‐amine‐cured spin‐coated films

Abstract Atomic force microscopy (AFM) was successfully used to study spin‐coated, amine‐cured epoxy film microstructure and morphology. The air‐epoxy and epoxy‐substrate interfaces were examined using tapping‐mode height and phase imaging AFM. The impact of relative humidity on the morphology and microstructure of the surfaces was determined. AFM was able to elucidate the changes on the surface as relative humidity during processing increased. It was observed that large nodular formations formed on the epoxy surface expose to the air but not epoxy surface formed on the substrate in addition to varying regions of more or less compliant structures, which was attributed to carbamate formation caused by the amine curing agent reaction with atmospheric CO 2 . Scanning electron microscopy (SEM) was used to further elucidate interface and interphase morphology of spin‐coated epoxies. Experimentation also demonstrated that post‐curing above the glass transition did not change the morphology structure, suggesting surface structures are “locked‐in.” SEM was used to further elucidate how the interface and interphase change with changing environmental conditions at both the air‐epoxy and epoxy‐substrate interface/interphases, including the impact of atmospheric CO 2 on Marangoni cell formation.

Shenk, Timothy M.↗
DOE OSTI2021

The interpenetration polymer network in a cement paste–waterborne epoxy system

The formation of the interpenetrating polymer network (IPN) structure within the cement-polymer system has been revealed by experiments from 2 dimensional to 3-dimensional scales. However, the microstructure design and performance prediction of IPN as a function of specific C-S-H/polymer components or ingredients' parameters e.g. water to cement ratios (w/c), polymer to cement ratios (p/c), monomer components, degree of polymerization (DP), etc. is by far not available. Here we developed a mesoscale model for IPN visualization based on the Flory-Huggins interaction theory which was applied to cement science for the first time. All the ingredients in the micro-structure were considered as soluble beads with rational sizes based on their properties obtained by molecular dynamic methods. The interaction parameters of each bead were then determined based on their element ratios and chemical backbones. The model was validated with the waterborne epoxy-cement material (WECM) in which a novel waterborne epoxy resin (WEP) was prepared and impregnated. The verification results on the 2D-3D scale show that the developed model predicts the WECM's IPN structures by rule and line concerning DP, w/c, and p/c in the mixture. The C-S-H beads were progressively scaled in size which alters the C-S-H texture to have completely different dissolution characteristics. Beads of diameter ~6 Å are more unstable and soluble which enable them to form a continuous phase in water or a composite structure with WEP. In contrast, beads with diameters larger than 10 Å have different properties with stronger nucleation effects. The results also suggest the impregnation content of WEP in cement-based material should be limited to 10% vol. to prevent the polymer IPN from decomposing into discrete clusters. The application of Flory-Huggins theory in cement-based composites demonstrates great potential in performance prediction and microstructure design.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Constitutional under-potential plating (CUP) – New insights for predicting the morphological stability of deposited lithium anodes in lithium metal batteries

Lithium (Li) cycling in lithium metal batteries (LMBs) inevitably witnesses a non-planar Li/electrolyte interface (cellular/dendritic microstructure) affecting the performance, safety and reliability of LMBs. Herein, the “constitutional under-potential plating” (CUP) concept is presented for the first time to understand the evolution, formation and predict the morphological stability/instability of the Li/electrolyte interface. Here, the CUP condition, a measure of the driving force for interface perturbation, occurs when the true potential gradient at the interface is smaller than the equilibrium electrodeposition potential gradient at the Li/electrolyte interface resulting in the electrolyte ahead of the Li-electrolyte interface to be in an under-potential state. Detailed CUP criterion calculations conducted herein establishes the relationship of battery operating conditions (e.g. current density, potential gradient) with the electrolyte properties (e.g. Li-ion transference number and diffusion coefficient) predicting the morphological stability condition at the interface. In addition to the driving force for interface perturbation, the capillarity effect or the Gibbs Thomson effect, a measure of the resistance to perturbation of the perturbed interface is discussed for understanding the influence of interfacial energy/adhesion energy between the current collector and the deposited Li on the overall morphological stability of the Li/electrolyte interface, a critical criterion for the unwanted dendritic morphology.

25 ENERGY STORAGE↗
DOE OSTI2025

High resolution microstructural, chemical studies and localized burnup analysis in an irradiated U–10Zr metallic fuel

This study involves high resolution characterization of a sodium bonded solid uranium (U)-10 wt% zirconium (Zr) metallic fuel irradiated in Fast Flux Test Facility (FFTF). The fuel centerline temperature during irradiation was estimated to be around 675 °C with the peak burnup 13.1 atomic percent. Samples for transmission electron microscopy (TEM) and atom probe tomography (APT) were prepared from different regions/zones in the fuel cross section radially to elucidate the microstructural changes and chemical redistribution of solute elements as well as fission products during irradiation experiment. TEM results indicate the irradiation in fast flux testing leads to the formation of extensive Zr-rich precipitates with varying sizes in the U–Zr fuel matrix. APT analysis performed to investigate redistribution of Zr, U and fission products along the radial direction of fuel pin showed Zr-rich precipitates entrapping the fission products in higher concentration as compared to the α-U phases. Here, the local burnup ( 235 U depletion) is found to be consistent, calculated by quantification of 235 U, 236 U and 238 U isotopes from mass spectrum obtained from APT along the radial direction. Zr-rich precipitation and its implication on fuel constitutional redistribution are discussed based on SEM, TEM and APT results.

APT↗
DOE OSTI2021

Self-Assembled BaTiO 3 –Au x Ag 1– x Low-Loss Hybrid Plasmonic Metamaterials with an Ordered “Nano-Domino-like” Microstructure

Metallic plasmonic hybrid nanostructures have attracted enormous research interest due to the combined physical properties coming from different material components and the broad range of applications in nanophotonic and electronic devices. However, the high loss and narrow range of property tunability of the metallic hybrid materials have limited their practical applications. In this study, a metallic alloy-based self-assembled plasmonic hybrid nanostructure, i.e., a BaTiO 3 –Au x Ag 1– x (BTO) vertically aligned nanocomposite, has been integrated by a templated growth method for low-loss plasmonic systems. Comprehensive microstructural characterizations including high-resolution scanning transmission electron microscopy (HRSTEM), energy-dispersive X-ray spectroscopy (EDS), and three-dimensional (3D) electron tomography demonstrate the formation of an ordered “nano-domino-like” morphology with Au 0.4 Ag 0.6 nanopillars as cylindrical cores and BTO as square shells. By comparing with the BTO–Au hybrid thin film, the BTO–Au 0.4 Ag 0.6 alloyed film exhibits much broader plasmon resonance, hyperbolic dispersion, low-loss, and thermally robust features in the UV–vis–NIR wavelength region. This study provides a feasible platform for a complex alloyed plasmonic hybrid material design with low-loss and highly tunable optical properties toward all-optical integrated devices.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Diversifying Composition Leads to Hierarchical Composites with Design Flexibility and Structural Fidelity

Although significant progress has been made in the self-assembly of nanostructures, present successes heavily rely on precision in building block design, composition, and pair interactions. These requirements fundamentally limit our ability to synthesize macroscopic materials where the likelihood of impurity inclusion escalates and, more importantly, to access molecular-to-nanoscopic-to-microscopic-to-macroscopic hierarchies, since the types and compositions of building blocks vary at each stage. Inspired by biological blends and high-entropy alloys, we hypothesize that diversifying the blend’s composition can overcome these limitations. Increasing the number of components increases mixing entropy, leading to the dispersion of different components and, as a result, enhances interphase miscibility, weakens the dependence on specific pair interactions, and enables long-range cooperativity. This hypothesis is validated in complex blends containing small molecules, block copolymer-based supramolecules, and nanoparticles/colloidal particles. Hierarchically structured composites can be obtained with formulation flexibility in the filler selection and blend composition. It is worth noting that, by adding small molecules, we can solve the size constraint that plagues traditional block copolymer/nanoparticle blends. Detailed characterization and simulation further confirm that each component is distributed to locally mediate unfavorable interactions, cooperatively mitigate composition fluctuations, and retain structural fidelity. Furthermore, the blends have sufficient mobility to access tunable microstructures without compromising the order of the nanostructure. Besides establishing a kinetically viable pathway to release current constraints in the composite design and to navigate uncertainties during structure formation over multiple length scales, the present study demonstrates that entropy-driven behaviors can be realized in systems beyond high-entropy alloys despite inherent differences between metal alloys and organic/inorganic hybrids.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Unravelling chloride transport/microstructure relationships for blended-cement pastes with the mini-migration method

A chloride mini-migration method is proposed to estimate effective diffusion coefficients at the scale of the cement paste and to investigate mechanisms with complementary microstructure analyses on the same material. Blended-cement pastes with a wide range of properties were investigated in this study: systems at w/b = 0.3–0.5 including Portland cement, white Portland cement, slag-Portland cement, fly ash, glass powder, and/or limestone and calcined clay. Comparisons showed the relative and combined importance of three main parameters on the effective diffusion coefficient: the porosity, the pore connectivity parameter and the conductivity of the pore solution (low values of the latter two are generally key aspects of the high resistance of blended-cement systems against chloride ingress). Notably, a general correlation for all the investigated systems was established between the effective diffusion coefficient and the bulk conductivity (whereas no simple correlation was observed between the effective diffusion coefficient and the formation factor or the pore connectivity parameter).

36 MATERIALS SCIENCE↗