SEARCH · Engineering Papers

Results for “Material Attributes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

All sources NASA NTRS DOE OSTI

DOE OSTI2024

Probing the active sites of oxide encapsulated electrocatalysts with controllable oxygen evolution selectivity

Electrocatalysts encapsulated by nanoscopic overlayers can control the rate of redox reactions at the outer surface of the overlayer or at the buried interface between the overlayer and the active catalyst, leading to complex behavior in the presence of two competing electrochemical reactions. This study investigated oxide encapsulated electrocatalysts (OECs) comprised of iridium (Ir) thin films coated with an ultrathin (2–10 nm thick) silicon oxide (SiO x ) or titanium oxide (TiO x ) overlayer. The performance of SiO x |Ir and TiO x |Ir thin film electrodes towards the oxygen evolution reaction (OER) and Fe(II)/Fe(III) redox reactions were evaluated. An improvement in selectivity towards the OER was observed for all OECs. Overlayer properties, namely ionic and electronic conductivity, were assessed using a combination of electroanalytical methods and molecular dynamics simulations. SiO x and TiO x overlayers were found to be permeable to H 2 O and O 2 such that the OER can occur at the MO x |Ir (M = Ti, Si) buried interface, which was further supported with molecular dynamics simulations of model SiO 2 coatings. In contrast, Fe(II)/Fe(III) redox reactions occur to the same degree with TiO x overlayers having thicknesses less than 4 nm as bare electrocatalyst, while SiO x overlayers inhibit redox reactions at all thicknesses. This observation is attributed to differences in electronic transport between the buried interface and outer overlayer surface, as measured with through-plane conductivity measurements of wetted overlayer materials. These findings reveal the influence of oxide overlayer properties on the activity and selectivity of OECs and suggest opportunities to tune these properties for a wide range of electrochemical reactions.

08 HYDROGEN↗

DOE OSTI2025

scons-novice

scons-novice is a re-write of the Software Carpentry https://software-carpentry.org/ "make-novice" source material https://github.com/swcarpentry/make-novice used to create the webpage lesson plan "Automation and Make" http://swcarpentry.github.io/make-novice/ which is licensed as under the Creative Commons Attribution license (CC BY 4.0) https://creativecommons.org/licenses/by/4.0/. scons-novice changes the lesson to teach SCons instead of Make.

Brindley, Kyle [Los Alamos National Laboratory]↗

DOE OSTI2025

Emergence of deep eutectic solvents (DES): chemistry, preparation, properties, and applications in biorefineries and critical materials

The emergence of renewable deep eutectic solvents (DES) as clean and efficient catalysts and solvents has created new opportunities for lignocellulosic biorefineries and critical material sectors, including chemical, energy, pharmaceutical, textile, and hydrometallurgical industries. This review provides an in-depth overview of DES, covering their chemistry, classifications, preparation methods, processing characteristics, and recyclability, while highlighting their unique attributes and industry relevant applications. Emphasis is placed on the integration of DES into advanced biorefinery systems, focusing on their tunable physicochemical and thermodynamic properties for biomass pretreatment and the production of value-added products. The review explores how DES can be tuned for selective dissolution of biomass components and evaluates production and valorization of DES-derived biochemicals, with attention to lignin extraction mechanisms and conversion of biomass into bioproducts and biofuels. Beyond biorefineries, the scope extends to DES applications in electrochemical energy devices, where they serve as electrolytes, synthesis media for electrode materials, and leaching agents in battery recycling. The multifunctional roles of DES in pharmaceutical, hydrometallurgical, and textile sectors are also explored for contributions to sustainable processing. Finally, the review identifies future research directions, outlining benefits, challenges, and knowledge gaps, for continued industrial development.

09 BIOMASS FUELS↗

DOE OSTI2025

Optically Addressable Light Valve Based on a GaN:Mn Photoconductor

Semi-insulating manganese-doped gallium nitride (GaN:Mn) layers epitaxially grown on unintentionally doped GaN substrates were used as photoconductors in optically addressable light valves (OALVs) to withstand higher operational laser fluences compared to current state-of-the-art OALVs where bismuth silicon oxide (BSO; Bi 12 SiO 20 ) layers are used as photoconductors. GaN:Mn promises to be an exciting material for optoelectronic operations due to its large laser fluence handling capability and photoresponsivity near the band edge. The laser damage thresholds for the semi-insulating epitaxial GaN:Mn layer and the n-type substrate layer were measured to be 2.4 and 4.2 J/cm 2 , respectively. These are 6–10 times higher than that of BSO (0.4 J/cm 2 ). These measurements were performed by exposing ~200 sites on the samples to increasing fluence levels from a Gaussian pulsed Nd:YAG laser system (1064 nm) operating at a 5 Hz repetition rate with a 3 ns pulse width. Photoresponsivity of the GaN:Mn material was investigated at discrete wavelengths of 447, 405, and 380 nm. Further, the peak photoresponsivity was observed under an illumination wavelength of 380 nm and is attributed to stronger absorption. The OALV was fabricated by attaching a 110-μm-thick GaN:Mn layer grown on a 280-μm-thick n-GaN layer to a 3-mm-thick BK7 optical window. A twisted nematic E7 liquid crystal was introduced to the 5 μm gap between the two components. Transmission levels of >90% were achieved for the fabricated OALVs for a peak voltage of 40 V, constrained by transmission “bleed-through”.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Impact of Humidity and Temperature on the Stability of the Optical Properties and Structure of MAPbI3, MA0.7FA0.3PbI3 and (FAPbI3)0.95(MAPbBr3)0.05 Perovskite Thin Films

In situ real-time spectroscopic ellipsometry (RTSE) measurements have been conducted on MAPbI3, MA0.7FA0.3PbI3, and (FAPbI3)0.95(MAPbBr3)0.05 perovskite thin films when exposed to different levels of relative humidity at given temperatures over time. Analysis of RTSE measurements track changes in the complex dielectric function spectra and structure, which indicate variations in stability influenced by the underlying material, preparation method, and perovskite composition. MAPbI3 and MA0.7FA0.3PbI3 films deposited on commercial fluorine-doped tin oxide coated glass are more stable than corresponding films deposited on soda lime glass directly. (FAPbI3)0.95(MAPbBr3)0.05 films on soda lime glass showed improved stability over the other compositions regardless of the substrate, and this is attributed to the preparation method as well as the final composition.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Persistent hot carrier diffusion in boron arsenide single crystals imaged by ultrafast electron microscopy

Cubic boron arsenide (BAs) is promising for microelectronics thermal management because of its high thermal conductivity. Recently, its potential as an optoelectronic material is also being explored. However, it remains challenging to measure its photocarrier transport properties because of small sizes of available high-quality crystals. Here, we use scanning ultrafast electron microscopy (SUEM) to directly visualize the diffusion of photocarriers in BAs single crystals. Surprisingly, we observed ambipolar diffusion at low optical fluence with persistent hot carrier dynamics for above 200 ps, which can likely be attributed to the large frequency gap between acoustic and optical phonons, the same feature that is responsible for the high thermal conductivity. At higher optical fluence, we observed spontaneous electron-hole separation. Our results show BAs is an attractive optoelectronic material combining high thermal conductivity and excellent photocarrier transport properties. Finally, our study also demonstrates the capability of SUEM to probe photocarrier transport in emerging materials.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Develop Accurate Techniques for Passive SiC Temperature Monitoring of Miniature Samples for Cross-Cutting Applications

Passive thermometry is critically important because most fuels and materials irradiation experiments are not instrumented, and it is necessary to understand the irradiation temperature to properly interpret any post-irradiation examination data, including evolving properties and/or microstructures. The standard passive thermometry approach uses continuous dilatometry to evaluate changes in the instantaneous coefficient of thermal expansion during post-irradiation thermal annealing. This approach has limitations in terms of sample size (minimum length requirements) and the maximum irradiation temperature that can be accurately determined, which is limited by the reduced swelling (and therefore recovery) following higher temperature irradiation and limitations on the furnaces used with push-rod dilatometers. This work evaluates two new proposed techniques for post-irradiation evaluation of passive SiC temperature monitors: differential scanning calorimetry (DSC) and Raman spectroscopy. DSC is an extremely sensitive technique that can be used for any specimen geometry and is capable of higher temperature operation. Raman spectroscopy is similar in that it is a surface technique capable of examining extremely small samples (submillimeter), can be used with a heated stage up to 1,500°C (planned for future work), and is capable of mapping local irradiation temperatures throughout a sample. Existing SiC samples that were previously irradiated over a wide range of temperatures were cut into multiple pieces to allow for annealing studies using multiple different techniques: dilatometry, DSC, and Raman spectroscopy. This approach mitigates the concern that samples analyzed using one technique may have a slightly different irradiation history than those analyzed using a different technique. Recovery was clearly observed during annealing using both DSC and dilatometry. In some cases, a direct comparison could not be made due to some of the DSC runs accidentally including material from multiple specimens and issues with using an alternative DSC sample holder for the highest temperature annealing studies. Nevertheless, one trend was clear: the DSC runs resulted in higher irradiation temperatures compared to those of the dilatometry runs. Part of this could be attributed to the higher temperature ramp rates used during the DSC runs, which are often preferred to reduce noise in the measurements. By comparison, dilatometry has previously been shown to produce better data at lower ramp rates. Future work should further investigate the ideal ramp rate for both techniques to produce consistent results. Additional work should evaluate the best holder material to use for DSC runs exceeding 1,000°C to provide reliable data while preventing interactions between SiC and the holder.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2025

Develop Accurate Techniques for Passive SiC Temperature Monitoring of Miniature Samples for Cross-Cutting Applications

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2021

Microstructure evolution of gadolinium doped cerium oxide under large thermal gradients

In this report the effects of large thermal gradient annealing on the microstructure of 10 mol% gadolinium doped ceria (GDC) were investigated. GDC powder was prepared by solvent deficient method and sintered at 1650 °C for 10 h to achieve dense ceramics with ~8 μm grain size. The densified GDC samples were subsequently annealed using a 60 W infrared laser at over 2100 °C for 1 h under a thermal gradient equivalent to ~0.3–0.5 °C/μm. The post-annealed samples at 2150 °C for 1 h exhibit grains with average length and width of 37 and 28 μm, respectively. Electron backscattered diffraction (EBSD) analysis revealed that the post-annealed sample at 2150 °C consists of grains oriented close to five principal directions (<4 3 10>, <0 0 1> and <13 1 14> on [0 0 1], and <7 6 20> and <7 2 7> on [0 1 0]) within a tolerance angle of ±10°, whereas the grains of the pre-annealed sample are randomly oriented. Gadolinium diffuses 20–30 μm away from the irradiated surface, with the measured composition of regions deeper than 30 μm, Ce 0.86 Gd 0.14 O 1.93 , is close to that of the pre-annealed sample, Ce 0.87 Gd 0.13 O 1.94 . Enhancement of total conductivity of the post-annealed GDC (1.1 × 10 -3 S cm -1 at 500 °C, and 2.1 × 10 -2 S cm -1 at 700 °C) is observed when compared to the pre-annealed GDC (3.1 × 10 -5 S cm -1 at 500 °C, and 1.7 × 10 -3 S cm -1 at 700 °C), and points to the decrease in the grain boundary (GB) resistivity. This could be attributed to both the change in GB area and grain alignment.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Neutron irradiation induced defects and clustering in NF616 and T91

NF616 is a third-generation ferritic martensitic steel, developed to have better creep resistance than the prior generation T91. Unlike relatively numerous studies of T91, there is a lack of understanding of the irradiation effect on the microstructural evolution and mechanical response of NF616. This work evaluated the microstructures and radiation hardening of NF616 irradiated up to 8.2 displacement per atom (dpa) at 292 °C – 431 °C, compared with T91 from two heats. Dislocation loops were observed in all investigated samples. NF616 exhibited comparable loop size but slightly lower loop density than those in the general T91 heat at 430 °C. Cavities were only observed in NF616 at 431 °C but absent at lower irradiation temperatures (292 °C and 359 °C). Ni-rich clusters were also observed in NF616 at 431 °C, while only weak Ni-clustering were observed at lower irradiation temperatures. Compared to the general T91 heat, NF616 demonstrated better swelling resistance (e.g., one third of swelling in the general T91 heat at 430 °C), a slightly higher number density of Ni-rich clusters, and slightly lower radiation hardening. The low-carbon T91 showed the greatest hardening with the largest swelling and loop sizes, despite its lowest irradiation temperature and intermediate dose. The calculated hardening from loops, cavities and Ni-rich clusters using the classic dispersed barrier-hardening model had reasonable agreement with the experiment-derived results, with the primary hardening contribution attributed to dislocation loops.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

Reassembled nanoprecipitates resisting radiation

Outstanding resistance to destructive radiation damage in structural alloys is realized by ultra-high-density reversible nanoprecipitate inclusions, and the improvement is attributed to the reordering process of low-misfit superlattices in highly supersaturated matrices.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Characterisation of nano-assemblies inside mesopores using neutron scattering

Adsorption of molecular and nanoscale matter in mesoporous materials is important in filtration and chromatography as well as membrane processes. However, the morphology and distribution of self-assembled structures of adsorbate formed within nanoconfined environments is largely unknown. Small Angle Neutron Scattering (SANS) with porous matrix matching the neutron scattering length density of the solvent has the potential to provide detailed information on the self-assemblies formed in pore spaces. However, analysis of such SANS profiles remains a challenge. In this study, we extend the SANS analysis method previously developed by Findenegg and co-workers to include interparticle correlations, providing a qualitative characterisation of the adsorption state of surfactants and nanoparticles in the cylindrical pores of silica nanomaterials. We find that the pore filling fraction and the self-assembled state of the adsorbate governs the scattering profile. We apply the model to two materials namely, triethyleneglycol monohexyl ether (C 6 E 3 ) surfactant and gold nanoparticles adsorbed in SBA-15 mesoporous silica. In contrast to the C 6 E 3 system, Bragg scattering dominates the diffuse scattering in gold nanoparticle system, which we attribute to the immobile internal structure of the nanoparticles. In conclusion, this new SANS analysis method has potential to elucidate structures of soft matter nanoassemblies inside mesopores.

74 ATOMIC AND MOLECULAR PHYSICS↗

DOE OSTI2020

Quenching of the relaxation pathway in the Weyl semimetal TaAs

Since tantalum arsenide (TaAs) has been experimentally verified as a Weyl semimetal, intensive research has been devoted to study of the unique properties of the material. Despite this, the ultrafast dynamics of TaAs is still not very well understood. In this work, we study the relaxation dynamics in TaAs using transient reflection spectroscopy. From the transient reflection measurement, we observe either a single (fast) or a dual (fast and slow) relaxation, depending on the probing wavelength. The additional relaxation channel is attributed to an asymmetric population of photoexcited electrons and holes.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Defect-mediated metastability and carrier lifetimes in polycrystalline (Ag,Cu)(In,Ga)Se 2 absorber materials

Using a combination of optical and electrical measurements, we develop a model for metastable defects in Ag-alloyed Cu(In,Ga)Se 2 , one of the leading thin film photovoltaic materials. By controlling the pre-selenization conditions of the back contact prior to the growth of polycrystalline (Ag,Cu)(In,Ga)Se 2 absorbers and subsequently exposing them to various stresses (light soaking and dark-heat), we explore in this paper the nature and role of metastable defects on the electro-optical and photovoltaic performance of high-efficiency solar cell materials and devices. Positron annihilation spectroscopy indicates that dark-heat exposure results in an increase in the concentration of the selenium–copper divacancy complex (V Se –V Cu ), attributed to depassivation of donor defects. Deep-level optical spectroscopy finds a corresponding increase of a defect at Ev+0.98 eV, and deep-level transient spectroscopy suggests that this increase is accompanied by a decrease in the concentration of mid-bandgap recombination centers. Time-resolved photoluminescence excitation spectroscopy data are consistent with the presence of the V Se –V Cu divacancy complex, which may act as a shallow trap for the minority carriers. Light-soaking experiments are consistent with the V Se –V Cu optical cycle proposed by Lany and Zunger, resulting in the conversion of shallow traps into recombination states that limit the effective minority carrier recombination time (and the associated carrier diffusion length) and an increase in the doping density that limits carrier extraction in photovoltaic devices.

14 SOLAR ENERGY↗

DOE OSTI2024

Computational design of high-entropy rare earth aluminum garnets for advanced thermal and environmental barrier coatings

To enhance the protection of Ni-based superalloys in gas turbine engines’ high-temperature environments, it’s crucial to develop advanced thermal/environmental barrier coating (T/EBC) materials with a balanced combination of thermal and mechanical properties. This optimization is essential to safeguard against chemical and thermal challenges. Here, in this study, we harness the power of density functional theory (DFT) in conjunction with combinatorial chemistry methodologies to engineer high-performance high-entropy rare earth disilicates of the RE 3 Al 5 O 12 family (where RE denotes Y, Gd, Er, and Yb). These materials are meticulously designed to exhibit superior phase stability, a targeted coefficient of thermal expansion (CTE), low lattice thermal conductivity, and robust mechanical properties. The determination of CTE values is accomplished through phonon calculations at various volume settings within the quasi-harmonic approximation, while lattice thermal conductivities are rigorously assessed employing the Debye-Callaway model, accounting for three distinct phonon processes. Our findings highlight the remarkable attributes of the solid solution (Y 1/4 Gd 1/4 Er 1/4 Yb 1/4 ) 3 Al 5 O 12 , which displays a reduction in lattice thermal conductivity compared to its individual constituents while maintaining a favorable range of CTE values. The novel T/EBC material, distinguished by their multifaceted functionalities, are poised to use in substantial enhancements in the performance of engines.

36 MATERIALS SCIENCE↗

DOE OSTI2021

High–Pressure Deformation of Iron–Nickel–Silicon Alloys and Implications for Earth’s Inner Core

Earth’s inner core exhibits strong seismic anisotropy, often attributed to the alignment of hexagonal close-packed iron (hcp-Fe) alloy crystallites with the Earth’s poles. How this alignment developed depends on material properties of the alloy and is important to our understanding of the core’s crystallization history and active geodynamical forcing. Previous studies suggested that hcp-Fe is weak under deep Earth conditions but did not investigate the effects of the lighter elements known to be part of the inner core alloy. Here, we present results from radial X-ray diffraction experiments in a diamond anvil cell that constrain the strength and deformation properties of iron-nickel-silicon (Fe–Ni–Si) alloys up to 60 GPa. We also show the results of laser heating to 1650 K to evaluate the effect of temperature. Observed alloy textures suggest different relative activities of the various hcp deformation mechanisms compared to pure Fe, but these textures could still account for the theorized polar alignment. Fe–Ni–Si alloys are mechanically stronger than Fe and Fe–Ni; extrapolated to inner core conditions, Si-bearing alloys may be more than an order of magnitude stronger. Furthermore, this enhanced strength proportionally reduces the effectivity of dislocation creep as a deformation mechanism, which may suggest that texture developed during crystallization rather than as the result of postsolidification plastic flow.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Synthesis of metastable Ruddlesden–Popper titanates, ( A TiO 3 ) n A O, with n ≥ 20 by molecular-beam epitaxy

We outline a method to synthesize ( ATiO 3 ) n AO Ruddlesden–Popper phases with high- n, where the A-site is a mixture of barium and strontium, by molecular-beam epitaxy. The precision and consistency of the method described is demonstrated by the growth of an unprecedented (SrTiO 3 ) 50 SrO epitaxial film. We proceed to investigate barium incorporation into the Ruddlesden–Popper structure, which is limited to a few percent in bulk, and we find that the amount of barium that can be incorporated depends on both the substrate temperature and the strain state of the film. At the optimal growth temperature, we demonstrate that as much as 33% barium can homogeneously populate the A-site when films are grown on SrTiO 3 (001) substrates, whereas up to 60% barium can be accommodated in films grown on TbScO 3 (110) substrates, which we attribute to the difference in strain. This detailed synthetic study of high n, metastable Ruddlesden–Popper phases is pertinent to a variety of fields from quantum materials to tunable dielectrics.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Planar Thermal Hall Effect from Phonons in Cuprates

A surprising “planar” thermal Hall effect, whereby the field is parallel to the current, has recently been observed in a few magnetic insulators; this effect has been attributed to exotic excitations such as Majorana fermions or chiral magnons. Here, we investigate the possibility of a planar thermal Hall effect in three different cuprate materials, in which the conventional thermal Hall conductivity 𝜅 xy (with an out-of-plane field perpendicular to the current) is dominated by either electrons or phonons. Our measurements show that the planar 𝜅 xy from electrons in cuprates is zero, as expected from the absence of a Lorentz force in the planar configuration. By contrast, we observe a sizable planar 𝜅 xy in those samples where the thermal Hall response is due to phonons, even though it should, in principle, be forbidden by the high crystal symmetry. Our findings call for a careful reexamination of the mechanisms responsible for the phonon thermal Hall effect in insulators.

Cuprates↗