Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MARTENSITE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

Quantification of complex-phase steel microstructure by using combined EBSD and EPMA measurements

Highlights: • In CP800 steel, bainite is the dominant phase with a typical lath (width 300 nm) structure and cementite precipitates. • Martensite is dispersed as small islands and only a few narrowed martensite bands are observed which has been induced by annealing process of cold rolled sheet. • The precise carbon content is measured in bainite and martensite utilizing EPMA line scans, which is around 0.2 wt% and 0.4 wt%, respectively. • Digitalization of the microstructure for CP800 is achieved by combining EBSD and EPMA techniques. • The final constituent map consists of plenty of microstructural features including topography, crystal structures, orientations and elemental distribution. - Abstract: We combined electron backscatter diffraction (EBSD) and electron probe microanalysis (EPMA) techniques to characterize the microstructure of industrial produced complex-phase CP800 steel. First, three major constituents (ferrite, martensite and bainite) are characterized. Then, transformation-induced dislocation zones in ferrite and bainitic regions consisting of different sub-structures are quantified and segmented. A final digitalized component map including plenty of microstructural features including crystal structures, orientations and elemental distribution are successfully achieved. The precise carbon content is measured in bainite and martensite utilizing EPMA line scans, which is around 0.2 wt% and 0.4 wt%, respectively. In the bainite phase of CP800, a typical Bagaryatski orientation relationship between cementite and lath-like bainitic ferrite is revealed based on the select diffraction patterns of transmission electron microscopy measurements.

36 MATERIALS SCIENCE↗

Effect of isochronal annealing on the microstructure, texture and mechanical properties of a cold-rolled high manganese steel

Highlights: • Recrystallised γ grains have similar orientations to reverted/recovered γ grains. • After reversion, γ orientations are correlated to ε and α′-martensite orientations. • γ nucleation at the boundary of reverted/recovered γ grains - Abstract: A Fe-17Mn-3Al-2Si-1Ni-0.06C wt.% steel was subjected to cold-rolling to 42% thickness reduction and isochronally annealed for 300 s between 500 and 850 °C. The high Mn steel was characterised via electron back-scattering diffraction, transmission electron microscopy and uniaxial tensile testing. The reversion of deformation-induced ε and α′-martensite to austenite (γ) was witnessed with the formation of fine twins in reverted/recovered γ grains after annealing to 650 °C. The nucleation of new γ grains at the boundary of reverted/recovered γ grains was also noted. Upon reversion, the γ orientations originated from the ε and α′-martensite orientations by phase transformation via the Shoji-Nishiyama and Kurdjumov-Sachs orientation relationships, respectively. Upon segmenting the γ grains, the recrystallised γ grains were observed to nucleate with orientations similar to those of the reverted/recovered γ grains. Uniaxial tension on a fully recrystallised γ microstructure showed that the initial γ grain size has a more significant effect on the yield strength than the ε and α′-martensite fractions. On the other hand, the initial ε and α′-martensite fractions affect the total elongation.

36 MATERIALS SCIENCE↗

Tuning austenite stability through prior microstructure control in a low-alloy Q&P steel

Quenching and partitioning (Q&P) processing is a widely accepted heat treatment methodology for creating high strength steels consisting of ferrite, martensite, and austenite, while maintaining relatively low manufacturing costs. Though the research on effects of prior microstructure is limited, an understanding of the heat treatment response of different starting microstructures is critical to processing and creating steels with complex microstructures that contain retained austenite and may afford opportunities to further optimize properties. This study investigates the influence of starting microstructure (ferrite/pearlite versus martensite) and prior levels of cold work (38 verses 58 %) on the microstructural development and mechanical properties of a 0.2 C-2.0 Mn-1.5 Si (wt.%) steel exposed to Q&P processing. Samples with a starting martensitic microstructure resulted in higher retained austenite fractions and a more homogeneous microstructure after Q&P processing compared to a starting microstructure of ferrite-pearlite. Starting martensitic microstructures also displayed higher work hardening rates and higher uniform elongations. Larger cold reductions saw accelerated dissolution kinetics and austenite formation during intercritical annealing, resulting in more similar final microstructures from the ferrite-pearlite and martensitic starting microstructures. Finally, the results presented here indicate that varying prior processing can be a route to manipulate and control austenite stability in a Q&P processed steel.

36 MATERIALS SCIENCE↗

Crystalline structure and magnetic behavior of the Ni 41 Mn 39 In 12 Co 8 alloy demonstrating giant magnetocaloric effect

Magnetic cooling is a green cooling technology, which is more energy efficient than existing fluid-compression cooling machines. Ni 41 Mn 39 In 12 Co 8 alloy, which demonstrates promising magnetocaloric performances, was investigated using neutron diffraction and thermomagnetic measurements. The austenite structure is cubic L2 1 $(Fm\bar{3}m),$ while that of the martensite is a mix of 8 and 6 M modulated monoclinic structures $(P\quad 1\quad 2/m\quad 1).$ The austenitic site occupancy refinements reveal that all substituting Co atoms occupy Ni-sites. Most Mn atoms (65%) are in the Mn-sites and the rest go to In-sites (about 35%) and Ni-sites (less than 5%). This disorder of the magnetic atoms (Mn, Ni and Co) in the austenitic phase remains unchanged during the martensitic transition. The distortions of the interatomic distances due to the modulation of the martensitic structures further enhance the disorder in the magnetic interactions. Thermomagnetic measurements indicate that the austenitic phase is ferromagnetic. Cooling to below 250 K, where the alloy loses its ferromagnetic nature, and down to 50 K, the lack of any antiferromagnetic Bragg peaks suggests no antiferromagnetic ordering in the martensitic phase. Here, at very low temperatures in the martensitic phase, spin glass magnetic nature is identified by magnetic measurements, and the spin-glass transition temperature is ~19 K.

36 MATERIALS SCIENCE↗

Mechanism of Influence of Nanocrystal Sizes on the Parameters of the Curves of the Pseudoelastic and Thermoelastic Deformations of Alloys with the Shape Memory Effect

The data available in the literature on the influence of the nanocrystal sizes of alloys with the shape memory effect on the parameters of the curves of their pseudoelastic and thermoelastic deformation are analyzed in the framework of the theory of diffuse martensitic transitions (DMT). The peculiarity of the DMT theory is that it is based on both thermodynamic and kinetic relationships that make it sensitive to the alloy structure on the mesoscopic scale. This enables one to state the functional dependence of the parameter of the martensitic deformation of the nanocrystals on the size of their cross section D. As a result of the analysis, it is found that the coefficient of the strain (martensitic) hardening and the hysteresis of the pseudoelastic strain curves of submicrocrystals of the Ni{sub 54}Fe{sub 19}Ga{sub 27} are changed with D by law 1/D{sup 2}. The temperature range (M{sub s} – M{sub f}) of the martensitic transition in TiNi alloy nanocrystals is changed by analogy law. These dependences are results of the constrained displacement of dislocations of the phase transformation by transverse sizes of the crystal. A kinetic mechanism of the appearance of the critical nanocrystal size D{sub k} is established; the transition of austenite to martensite does not occur at transverse crystal sizes smaller than the critical size.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Applicability of a Micromechanics Model Based on Actual Microstructure for Failure Prediction of DP Steels

In this paper, various micromechanics models based on actual microstructures of DP steels are examined in order to determine the reasonable range of martensite volume fraction where the methodology described in this study can be applied. For this purpose, various micromechanics-based finite element models are first created based on the actual microstructures of DP steels with different martensite volume fractions. These models are, then, used to investigate the influence of ductility of the constituent ferrite and martensite phases and also the influence of voids in the ferrite phase on the overall ductility of DP steels. The computational results indicate that there is a range of martensite volume fraction where the phase inhomogeneity between the ferrite and martensite phases has dominant effect on the overall ductility of DP steels, defeating the influence of the ductility of each phase and the voids in the ferrite phase, and that this phase inhomogeneity dominant region includes the range of marteniste volume fraction between 15% and 40%. Therefore, the methodology, adopted in this study, may be applied to DP steels within the phase inhomogeneity dominant region in tailoring the DP steel design for its intended purpose and desired properties.

36 MATERIALS SCIENCE↗

An assessment of the contributing factors to the superior properties of a nanostructured steel using in situ high-energy X-ray

In contrast to most nanostructured materials, outstanding mechanical property has been demonstrated in a nanostructured metastable austenitic steel, owing to the new characteristics of deformation-induced martensitic transformation. In this paper, by employing an in situ high-energy X-ray diffraction technique, we explore these characteristics by examining factors from the load partitioning, Lu ders banding, to texture development. It was found that the martensitic transformation was mainly driven through Lu ders band propagation. Marked load transfer takes place from austenite to martensite as Lu ders band propagates, and continues into the homogeneous deformation regime. The texture development is mostly contributed by martensitic transformation, but dislocation-based plasticity also plays a role. The effective load partitioning along with the deformability of martensite promotes sample ductility.

36 MATERIALS SCIENCE↗

Effects of Overlapping Distances on Steel Microstructure and Properties After Multi-track Laser Quenching

In this study, multi-track laser quenching with different overlapping distances was used to assess SM45C microstructure and properties. Two overlapping distance types were evaluated, including overlapping distances in the transition and martensite regions, respectively. After multi-track quenching, hardness showed a threefold increase. With the overlapping distance in the transition region, surface hardness varied from 600 to 700 HV. There was a region of low hardness in each track. Hardness in the low hardness region was from 300 to 400 HV. The average hardness was basically over 500 HV with the overlapping distance in the martensite region, although there was a softening region. The increased hardness was mainly caused by the martensite. Microstructure in the overlapping region was self-tempered martensite, retained austenite and ferrite. Tempered sorbite and lowly tempered martensite were observed in heat-affected zones. Friction coefficients of quenched specimens varied between 0.275 and 0.325, with a 14% reduction relative to the base metal. The wear rate of the quenched specimen was only 40.8% of the base metal. With time, mass reduction in the quenched specimen was much smaller than that of the base metal. For specimens treated with laser quenching, slight fatigue wear was dominating.

36 MATERIALS SCIENCE↗

The effect of microstructure on the dynamic shock response of 1045 steel

Herein, the effect of microstructure on the shock response of 1045 steel is investigated via plate impact experiments and postmortem characterization. Three unique microstructures are explored: ferrite-pearlite, martensite, and ferrite with spheroidal cementite (i.e. spheroidized). Two spall recovery experiments, at approximate peak pressures of 3.2 and 3.5 GPa, are conducted to assess the Hugoniot elastic limit (HEL), spall strength, and damage morphology of the various microstructures. The ferrite-pearlite and martensite microstructures exhibit continuous yielding at both quasi-static and dynamic rates, while the spheroidized condition displays discontinuous yielding. Discontinuous yielding of the spheroidized microstructure is attributed to a combined low initial dislocation density coupled with a low dislocation nucleation rate. The spall strength of ferrite-pearlite is consistently lower than the spheroidized microstructure, attributed to elongated cementite that is more susceptible to cracking than more spherical cementite precipitates. Despite a high density of boundaries, martensite exhibits the highest spall strength. A large percentage of the boundaries within the martensite microstructure are found to be low energy (i.e. Σ3 or low angle), and are thus less susceptible to spall damage. Overall, the high spall strength of martensite is likely linked to traditional strengthening mechanisms that limit dislocation motion.

36 MATERIALS SCIENCE↗

The effect of Ti content on age hardening and mechanical properties of uranium-titanium alloys

Here, the effect of Ti content on age hardening and the resulting mechanical properties are described for -quenched U-Ti alloys containing 0.3 wt.% to 2.0 wt.%Ti. Age hardening occurs between ~250°C and ~450°C. Overaging occurs at higher temperatures by cellular decomposition. Age hardening kinetics suggest that different mechanisms occur depending on Ti content and initial microstructure. Strengthening in 'a acicular martensites begins by the formation of Ti clusters which evolve into thin U 2 Ti disc shaped precipitates and later mature into continuous U 2 Ti rods beginning at peak hardness. The mechanism of hardening in 'b banded martensite is more elusive, as significant hardening occurs where atomic mobility is lower than that required for precipitate formation, similar to that reported for age hardening in ''b banded martensite in U-6%Nb. The activation energy for aging varies with Ti content and microstructure. In fully martensitic alloys containing 0.75% to 2.0%Ti it is in the vicinity of ~44 kcal/mole (184 kJ/mole). But it is lower in alloys containing less than 0.6%Ti where quenched microstructures are less than fully martensitic. Tensile ductility is high prior to aging, decreases with age hardening, is effectively zero at peak hardness, and remains low in overaged conditions. Attractive combinations of strength and ductility are best obtained in alloys containing 0.6% to 1.0%Ti which have been partially aged to fractional hardening levels no greater than ~0.6. This corresponds to the very early stages of aging, associated with clustering and the earliest stages of U 2 Ti disc formation. Alloys containing 0.45%Ti or less are not as responsive to age hardening. Alloys containing 1.5% and 2.0%Ti can be aged to higher strengths, but extreme quench rate sensitivity prevents them from being effectively heat treated in realistic section thicknesses.

36 MATERIALS SCIENCE↗

The significant impact of cold deformation on structure-property relationship in phase reversion-induced stainless steels

Highlights: • Parts of metastable austenite transformed into strain-induced martensite in 18Cr-8Ni stainless steel during cold-rolled process. • The kinetics of reversion transformation from martensite to austenite was fastest in 90% cold-rolled sample during annealing treatment. • The austenite grain size for the 90% cold-rolled sample after annealing was smallest and most uniform, which induced highest yield strength and elongation combination. - Abstract: The present study aims to investigate the impact of cold deformation on structure-property relationship in phase reversion-induced stainless steels. The commercial 18Cr-8Ni stainless steel was cold rolled at room temperature to 30%, 60% and 90% thickness reduction, respectively and subsequently annealed at 900 °C for 1–100 min. Evolution of phases in selected samples was identified and quantified by X-ray diffraction together with the corresponding microstructural characterization through optical, scanning and transmission electron microscopy, and electron backscatter diffraction. Mechanical properties of selected samples were determined by the tensile test. The results indicated that parts of metastable austenite transformed into strain-induced martensite during cold rolling process, and the volume fraction of martensite increased with increase in cold rolling reduction. The kinetics of reversion transformation from martensite to austenite was fastest in 90% cold-rolled sample during annealing treatment. The austenite grain size for the 90% cold-rolled sample after annealing was smallest and most uniform, which induced highest yield strength and elongation combination.

36 MATERIALS SCIENCE↗

Deformation behavior of additively manufactured GP1 stainless steel

In-situ neutron diffraction measurements were performed in this paper during heat-treating and uniaxial loading of additively manufactured (AM) GP1 material. Although the measured chemical composition of the GP1 powder falls within the composition specifications of 17-4 PH steel, a fully martensitic alloy in the wrought condition, the crystal structure of the as-built GP1 material is fully austenitic. Chemical analysis of the as-built material shows high oxygen and nitrogen content, which then significantly decreased after heat-treating in a vacuum furnace at 650 °C for one hour. Significant austenite-to-martensite phase transformation is observed during compressive and tensile loading of the as-built and heat-treated material with accompanied strengthening as martensite volume fraction increases. During loading, the initial average phase stress state in the martensite is hydrostatic compression independent of the loading direction. Finally, preferred orientation transformation in austenite and applied load accommodation by variant selection in martensite are observed via measurements of the texture development.

36 MATERIALS SCIENCE↗

An in situ neutron diffraction study of anomalous superelasticity in a strain glass Ni 43 Fe 18 Ga 27 Co 12 alloy

Superelastic behavior is traditionally related to the martensitic transition with a collective transformation scenario in some shape memory alloys. A kind of quasi-linear superelasticity accompanied by a finite avalanche or confined martensitic transformation was recently found in some alloy systems with strain glass state. Here, an in situ neutron diffraction technique was used to study the deformation behavior in an Ni 43 Fe 18 Ga 27 Co 12 alloy with strain glass state in order to reveal the new intrinsic physical nature of the quasi-linear superelasticity. A significant modulus softening prior to the stress-induced martensitic transformation was observed during compression in the studied alloy, which is similar to the characteristics exhibited in the tweed precursor phenomena prior to temperature-induced martensitic transformation. Moreover, the diffraction peak broadening was further shown during the elastic stage of deformation for both single-crystal and polycrystalline samples, which mainly stems from the short-range fluctuation in the strain field inside each grain based on Williamson–Hall analysis. The authors believe that there exists a spatial heterogeneity in the modulus of the confined martensitic transformation alloy.

Zhang, Q. H.↗

Advanced micromechanical model for transformation-induced plasticity steels with application of in-situ high-energy x-ray diffraction method.

Compared to other advanced high-strength steels, transformation-induced plasticity (TRIP) steels exhibit better ductility at a given strength level and can be used to produce complicated automotive parts. This enhanced formability comes from the transformation of retained austenite to martensite during plastic deformation. In this study, as a first step in predicting optimum processing parameters in TRIP steel productions, a micromechanical finite element model is developed based on the actual microstructure of a TRIP 800 steel. The method uses a microstructure-based representative volume element (RVE) to capture the complex deformation behavior of TRIP steels. The mechanical properties of the constituent phases of the TRIP 800 steel and the fitting parameters describing the martensite transformation kinetics are determined using the synchrotron-based in-situ high-energy X-ray diffraction (HEXRD) experiments performed under a uniaxial tensile deformation. The experimental results suggest that the HEXRD technique provides a powerful tool for characterizing the phase transformation behavior and the microstress developed due to the phase-to-phase interaction of TRIP steels during deformation. The computational results suggest that the response of the RVE well represents the overall macroscopic behavior of the TRIP 800 steel under deformation. The methodology described in this study may be extended for studying the effects of the various processing parameters on the macroscopic behaviors of TRIP steels.

36 MATERIALS SCIENCE↗

Use of time history speckle pattern and pulsed photoacoustic techniques to detect the self-accommodating transformation in a Cu-Al-Ni shape memory alloy

Continuous and pulsed electromagnetic radiation was used to detect the self-accommodation mechanism on a polycrystalline Cu-13.83 wt.%Al-2.34 wt.%Ni shape memory alloy. Rectangular samples of this alloy were mechanically polished to observe the austenite and martensite phases. The samples were cooled in liquid nitrogen prior to the experiments to obtain the martensite phase. Using a dynamic speckle technique with a continuous wave laser we obtained the time history of the speckle pattern image and monitored the surface changes caused by the self-accommodation mechanism during the inverse (martensitic to austenitic) transformation. Using a photoacoustic technique based on a pulsed laser source it was also possible to detect the self-accommodation phenomena in a bulk sample. For comparison purposes, we used differential scanning calorimetry (DSC) to detect the critical temperatures of transformation and use these as reference to evaluate the performance of the optical and photoacoustical techniques. In all cases, the same range of temperature was obtained during the inverse transformation. From these results, we conclude that time history speckle pattern (THSP) and pulsed photoacoustic are complementary techniques; they are non-destructive and useful to detect surface and bulk martensitic transformation induced by a temperature change.

36 MATERIALS SCIENCE↗

Optimization of hot workability and microstructure control in a 12Cr-10Ni precipitation hardenable stainless steel: An approach using processing maps

Highlights: • Deformation processing map was developed for a 12Cr10Ni precipitation hardenable martensitic stainless steel and optimized hot working parameters were suggested to obtain defect free products. • The ‘stable’ domain of the processing maps were correlated to the dynamic recrystallization in the austenite phase and further confirmed by detailed microstructural investigations. • The DRx domain showed a refinement of the martensite packet size and of the prior transformation austenite grain size, essential to obtain the desired mechanical properties. - Abstract: Optimization of hot working parameters and corresponding microstructure control were explored in a 12Cr-10Ni precipitation hardenable martensitic stainless steel. From hot compression tests, 1073–1373 K (800°–1100 °C) and five (0.001–10 s{sup −1}) different strain rates, processing maps were developed, and various domains of microstructure evolution (in the austenite phase) were identified. The stable domain of the processing maps appeared to indicate dynamic recrystallization (DRx) in the austenite phase: as evident by the appearance of inflection point in the strain hardening rate versus flow stress plots. The suspected DRx domain was further confirmed by detailed microstructural investigations of the respective water-quenched specimens. The DRx domain showed a refinement of the martensite packet size and of the prior transformation austenite grain size. The later was shown with optical microstructure and reconstructed (modelled) microtexture data of the prior austenite grains. Additionally, the DRx domain showed a significant difference in activation energy as estimated from appropriate constitutive modelling.

36 MATERIALS SCIENCE↗

Structure and exchange bias of Ni{sub 50}Mn{sub 37}Sn{sub 13} ribbons

Ni{sub 50}Mn{sub 37}Sn{sub 13} ribbons were produced by the melt-spinning method. Structure and magnetic measurements on the Ni{sub 50}Mn{sub 37}Sn{sub 13} ribbons indicated that it is ferromagnetic below 340 K and undergoes an austenitic-to-martensitic phase transition just below room temperature. The austenitic phase has the cubic L2{sub 1} structure, with the excess manganese atoms occupying the 4(b) sites. The martensitic phase has an orthorhombic structure. With increasing applied magnetic field, the martensite start temperature M{sub s} and martensite finish temperature M{sub f} shift to lower temperatures because of the field-induced phase transition. The exchange-bias effect is observed and strongly varied with different cooling fields at low temperature. At 5 K, the exchange-bias field reaches a maximum of 290 Oe when the cooling field increases to 200 Oe, and then reduces sluggishly with further increase of the cooling field because of weakening of exchange coupling between antiferromagnetic and ferromagnetic interfaces.

36 MATERIALS SCIENCE↗