Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MAGNESIUM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

Characterization of High Strain Rate Mechanical behavior of AZ31 magnesium alloy using 3D Digital Image Correlation

Characterization of the material mechanical behavior at sub-Hopkinson regime (0.1 to 1000 s{sup -1}) is very challenging due to instrumentation limitations and the complexity of data analysis involved in dynamic loading. In this study, AZ31 magnesium alloy sheet specimens are tested using a custom designed servo-hydraulic machine in tension at nominal strain rates up to 1000 s{sup -1}. In order to resolve strain measurement artifacts, the specimen displacement is measured using 3D Digital Image correlation instead from actuator motion. The total strain is measured up to {approx} 30%, which is far beyond the measurable range of electric resistance strain gages. Stresses are calculated based on the elastic strains in the tab of a standard dog-bone shaped specimen. Using this technique, the stresses measured for strain rates of 100 s{sup -1} and lower show little or no noise comparing to load cell signals. When the strain rates are higher than 250 s{sup -1}, the noises and oscillations in the stress measurements are significantly decreased from {approx} 250 to 50 MPa. Overall, it is found that there are no significant differences in the elongation, although the material exhibits slight work hardening when the strain rate is increased from 1 to 100 s{sup -1}.

36 MATERIALS SCIENCE↗

Declamped Piezoelectric Coefficients in Patterned 70/30 Lead Magnesium Niobate–Lead Titanate Thin Films

Lateral subdivision of blanket piezoelectric thin films increases the functional properties through both increased domain wall mobility and declamping of the intrinsic response. This work presents the local effects of substrate declamping on the piezoelectric coefficient d 33,f of 300 nm thick, rhombohedral, {001}-oriented lead magnesium niobate–lead titanate thin films at the 70/30 composition (70PMN–30PT). Films grown by chemical solution deposition on platinized Si substrates are patterned into strip structures ranging from 0.75 to 9 µm in width. The longitudinal piezoelectric coefficient, d 33,f , is interrogated as a function of position across the patterned structures by three approaches: finite element modeling, piezoresponse force microscopy, and nanoprobe synchrotron X-ray diffraction. It is found that d 33,f increases from the clamped value of 40–50 to ≈160 pm V -1 at the free sidewall under 200 kV cm -1 excitation. The sidewalls partially declamp the piezoelectric response 500–600 nm into the patterned structure, raising the piezoelectric response at the center of features with lateral dimensions less than 1 µm (3:1 width to thickness aspect ratio). The normalized data from all three methods are in excellent agreement, with quantitative differences providing insight to the field dependence of the piezoelectric coefficient and its declamping behavior.

36 MATERIALS SCIENCE↗

Conductive and Stable Magnesium Oxide Electron-Selective Contacts for Efficient Silicon Solar Cells

A high Schottky barrier (>0.65 eV) for electrons is typically found on lightly doped n–type crystalline (c–Si) wafers for a variety of contact metals. This behavior is commonly attributed to the Fermi–level pinning effect and has hindered the development of n–type c–Si solar cells, while its p–type counterparts have been commercialized for several decades, typically utilizing aluminium alloys in full–area, and more recently, partial–area rear contact configurations. Here the authors demonstrate a highly conductive and thermally stable electrode composed of a magnesium oxide/aluminium (MgOx/Al) contact, achieving moderately low resistivity Ohmic contacts on lightly doped n–type c–Si. The electrode, functionalized with nanoscale MgO x films, significantly enhances the performance of n–type c–Si solar cells to a power conversion efficiency of 20%, advancing n–type c–Si solar cells with full–area dopant–free rear contacts to a point of competitiveness with the standard p–type architecture. Here, the low thermal budget of the cathode formation, its dopant–free nature, and the simplicity of the device structure enabled by the MgO x /Al contact open up new possibilities in designing and fabricating low–cost optoelectronic devices, including solar cells, thin film transistors, or light emitting diodes.

36 MATERIALS SCIENCE↗

Crystal structure, thermal expansivity, and elasticity of OH-chondrodite: Trends among dense hydrous magnesium silicates

Here, we report the structure and thermoelastic properties of OH-chondrodite. The sample was synthesized at 12 GPa and 1523 K, coexisting with hydroxyl-clinohumite and hydrous olivine. The Fe content Fe/(Fe+Mg) is 1.1 mol%, and the monoclinic unit-cell parameters are: a = 4.7459(2) Å, b = 10.3480(7) Å, c = 7.9002(6) Å, α = 108.702(7)°, and V = 367.50(4) Å3. At ambient conditions the crystal structure was refined in space group P 2 1 /b from 1915 unique reflection intensities measured by single-crystal x-ray diffraction. The volume thermal expansion coefficient was measured between 150 and 800 K, resulting in α V = 2.8(5)×10 -9 (K -2 ) × T + 40.9(7) × 10 -6 (K -1 ) – 0.81(3)(K)/T 2 , with an average value of 38.0(9)×10 -6 K -1 . Brillouin spectroscopy was used to measure a set of acoustic velocities from which all thirteen components (C ij ) of the elastic tensor were determined. The Voigt-Reuss-Hill average of the moduli yield for the adiabatic bulk modulus, K S 0 = 117.9(12) GPa, and for shear modulus, G 0 = 70.1(5) GPa. The Reuss bound on the isothermal bulk modulus (K T0 ) is 114.2(14) GPa. From the measured thermodynamic properties, the Grüneisen parameter (γ) is calculated to be 1.66(4). Fitting previous static compression data using our independently measured bulk modulus (isothermal Reuss bound) as a fixed parameter, we refined the first pressure derivative of the bulk modulus, K T ’ = 5.5(1). Systematic trends between H 2 O content and physical properties are evaluated among dense hydrous magnesium silicate (DHMS) phases along the forsterite-brucite join.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Preparation of MgCo 2 O 4 /graphite composites as cathode materials for magnesium-ion batteries

Magnesium-ion batteries are fabricated with MgCo 2 O 4 /graphite composites as the cathode material. MgCo 2 O 4 nanoparticles are arranged using a co-precipitation method. A three-dimensional mixing process is utilized to mechanically decorate MgCo 2 O 4 nanoparticles on graphite particles. The MgCo 2 O 4 spinel crystals of size ranging from 20 to 70 nm on micrometer-sized graphite chunks are analyzed by using X-ray diffraction and scanning electron microscopy. The electrochemical properties of the as-prepared composites are well characterized by cyclic voltammetry, charge and discharge cycling, and electrochemical impedance spectroscopy (EIS). Interestingly, the MgCo 2 O 4 /graphite composite with a relatively low proportion of MgCo 2 O 4 , compared with the other as-prepared composites, achieves the highest specific capacity of 180 mAh g –1 at a C rate of 0.05 C. EIS results suggest that the electrical conductivity of the composite material is an increasing function of the graphite proportion. The superior performance of the MgCo 2 O 4 /graphite composite could be ascribed to the decoration of nanosized MgCo 2 O 4 particles as well as to the increased conductivity provided by graphite.

25 ENERGY STORAGE↗

Proximity Effect of Magnesium Diboride on Single-Walled Carbon Nanotube: an Ab Initio Study

Magnesium diboride (MgB{sub 2}) superconductor with excellent physical properties continues to attract the attention of researchers since its discovery. It derives its versatility from the absence of weak links, large coherence length, and small anisotropy. On the other hand, reports of superconductivity in small-diameter single-walled carbon nanotubes (SWCNTs) suspended between superconducting contacts and proximity induced supercurrents in Ta/SWNTs/Au junctions have also aroused great interest in the scientific community. Proximity induced superconductivity in SWCNTs has opened up new frontiers of research which will lead to many novel discoveries. This paper reports ab initio investigations on the proximity effect of MgB{sub 2} on the electronic structure of a SWCNT. Condensation of electronic states is observed in the electronic band structure of the pristine SWCNT when MgB{sub 2} is held in proximity. An additional band gap is generated below the lowest energy state of the valence band of the pristine CNT which we suggest, is due to Cooper pair formation. This leads to the prediction that SWCNTs will show superconducting properties in proximity of MgB{sub 2}. We envision MgB{sub 2}-coated SWCNTs as a novel nanomaterial that has a combination of proximity induced superconductivity and inherently unique mechanical and optical properties of SWCNTs.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of Preparation Conditions on the Structure and Magnetic Properties of Metal-Doped Magnesium Ferrites Synthesized From Laterite Leaching Solutions

In this paper, metal-doped magnesium ferrites (MgFe{sub 2}O{sub 4}) were synthesized from laterite leaching solutions using a coprecipitation-calcination method. The as-synthesized samples were characterized by x-ray diffraction (XRD), Fourier transform infrared spectrometer (FTIR), and physical property measurement system (PPMS) to determine the structure and magnetic properties. The effects of preparation conditions including precipitant reagents and metal ion concentrations in the laterite leaching solutions on the as-prepared spinel ferrites were investigated systematically. It is indicated that Ni–Co–Mn-doped MgFe{sub 2}O{sub 4} and Mn–Al–Cr-doped MgFe{sub 2}O{sub 4} could be synthesized from laterite leaching solutions by using sodium hydroxide (NaOH) and ammonia solution (NH{sub 3}⋅H{sub 2}O) as precipitant reagent, respectively. By adjusting the metal ion concentrations in the laterite leaching solutions, Ni–Co–Mn-doped MgFe{sub 2}O{sub 4} with different substitution contents were obtained. With the Ni and Mn substitution content increasing, the lattice constant and average grain size decreased, while x-ray density increased correspondingly. Magnetic property tests indicated that all the as-prepared samples exhibited typical ferrimagnetic behavior at room temperature, and the saturation magnetization (Ms) depended on the Ni, Co, and Mn substitution content. Specifically, the Ms and Hc values of the as-prepared metal-doped MgFe{sub 2}O{sub 4} sample with optimum substitution content of 0.185 could reach 33.22 emu g{sup −1} and 53 Oe, respectively.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Synthesis, structure, and magnetic properties of magnesium bis-3,6-di-tert-butyl-о-benzosemiquinonate complexes with N-donor ligands

A series of six-coordinate magnesium bis-3,6-di-tert-butyl-о-benzosemiquinonate complexes with different N-donor ligands (2,2´-dipyridyl, 1,10-phenanthroline, 2,9-dimethyl-1,10-phenanthroline, pyridine, N-phenyl-1-(4-pyridinyl)methanimine) were synthesized. The molecular and crystal structures of these complexes were determined by X-ray diffraction. In the complexes with bidentate N-donor ligands, the O,O-diolate o-semiquinone ligands are cis to each other, whereas the compounds with monodentate ligands contain organic radical anions in trans positions. The specific features of magnetic exchange coupling between organic radical ligands were studied by temperature-dependent magnetic susceptibility measurements.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Metal-organic frameworks based on magnesium(II): adsorption and luminescence properties

Two new metal-organic frameworks based on magnesium(II) ions, [Mg{sub 4}(bdc){sub 3}(dma){sub 6}(NO{sub 3}){sub 2}]•DMA (1; bdc is 1,4-benzenedicarboxylate; dma, DMA is N,N-dimethylacetamide) and [Mg{sub 3}(bpdc){sub 3}(nmp){sub 4}] (2; bpdc is 4,4´-biphenyldicarboxylate; nmp is N-methylpyrrolidone), were synthesized in DMA or NMP, respectively. According to the single-crystal X-ray diffraction data, compound 1 is built of binuclear carboxylate units {Mg_2(O_2CR)_3}, which were previously not observed in metal-organic frameworks. Compound 2 is based on trinuclear carb oxylate units {Mg_3(O_2CR)_6}. Compound 1 has a layered structure (hcb topology), whereas compound 2 has a distorted three-dimensional cubic structure (pcu topology). The phase purity and chemical identity of the compounds were confirmed by IR spectroscopy, thermogravimetry, elemental analysis, and powder X-ray diffraction. Photoluminescence properties of both compounds are indicative of intraligand charge-transfer transitions of one (for 1) or two (for 2) types. Textural characteristics of an activated sample of 1 were measured by nitrogen and hydrogen adsorption at 77 K and by carbon dioxide adsorption at 195 K.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The Effect of Thermomechanical Processing on the Tensile, Fatigue, and Creep Behavior of Magnesium Alloy AM60

Tensile, fatigue, fracture toughness, and creep experiments were performed on a commercially available magnesium-aluminum alloy (AM60) after three processing treatments: (1) as-THIXOMOLDED (as-molded), (2) THIXOMOLDED then thermomechanically processed (TTMP), and (3) THIXOMOLDED then TTMP then annealed (annealed). The TTMP procedure resulted in a significantly reduced grain size and a tensile yield strength greater than twice that of the as-molded material without a debit in elongation to failure ({epsilon}{sub f}). The as-molded material exhibited the lowest strength, while the annealed material exhibited an intermediate strength but the highest {epsilon}{sub f} (>1 pct). The TTMP and annealed materials exhibited fracture toughness values almost twice that of the as-molded material. The as-molded material exhibited the lowest fatigue threshold values and the lowest fatigue resistance. The annealed material exhibited the greatest fatigue resistance, and this was suggested to be related to its balance of tensile strength and ductility. The fatigue lives of each material were similar at both room temperature (RT) and 423 K (150 C). The tensile-creep behavior was evaluated for applied stresses ranging between 20 and 75 MPa and temperatures between 373 and 473 K (100 and 200 C). During both the fatigue and creep experiments, cracking preferentially occurred at grain boundaries. Overall, the results indicate that thermomechanical processing of AM60 dramatically improves the tensile, fracture toughness, and fatigue behavior, making this alloy attractive for structural applications. The reduced creep resistance after thermomechanical processing offers an opportunity for further research and development.

36 MATERIALS SCIENCE↗

Transient Heat and Material Flow Modeling of Friction Stir Processing of Magnesium Alloy using Threaded Tool

A three-dimensional transient computational fluid dynamics (CFD) model was developed to investigate the material flow and heat transfer during friction stir processing (FSP) in an AZ31B magnesium alloy. The material was assumed to be a non-Newtonian viscoplastic fluid, and the Zener-Hollomon parameter was used to describe the dependence of material viscosity on temperature and strain rate. The material constants used in the constitutive equation were determined experimentally from compression tests of the AZ31B Mg alloy under a wide range of strain rates and temperatures. A dynamic mesh method, combining both Lagrangian and Eulerian formulations, was used to capture the material flow induced by the movement of the threaded tool pin. Massless inert particles were embedded in the simulation domain to track the detailed history of material flow. The actual FSP was also carried out on a wrought Mg plate where temperature profiles were recorded by embedding thermocouples. The predicted transient temperature history was found to be consistent with that measured during FSP. Finally, the influence of the thread on the simulated results of thermal history and material flow was studied by comparing two models: one with threaded pin and the other with smooth pin surface.

36 MATERIALS SCIENCE↗

Numerical assessment of the role of slip and twinning in magnesium alloy AZ31B during loading path reversal

Magnesium alloy AZ31B plastically deforms via twinning and slip. Corresponding to the unidirectional nature of twinning, the activity of twinning/detwinning is directly related to loading history and materials texture. Using the elastic viscoplastic self-consistent model implementing with the twinning and detwinning model (EVPSC–TDT), we revisited experimental data of AZ31B sheets under four different strain paths: (1) tension–compression–tension along rolling direction, (2) tension–compression–tension along transverse direction, (3) compression–tension–compression along rolling direction, and (4) compression–tension–compression along transverse direction, and identified the dominant deformation mechanisms with respect to the strain path. We captured plastic deformation behaviors observed in experiments and quantitatively interpreted experimental observations in terms of the activities of different deformation mechanisms and the evolution of texture. It is found that the in-plane pre-tension has slight effect on the subsequent deformation, and the pre-compression and the reverse tension after compression have significant effect on the subsequent deformation. The inelastic behavior under compressive unloading is found to be insignificant at a small strain level but pronounced at a large strain level. Lastly, such significant effect is mainly ascribed to the activity of twinning and detwinning.

36 MATERIALS SCIENCE↗

Use of Friction Stir Processing for Improving Heat-Affected Zone Liquation Cracking Resistance of a Cast Magnesium Alloy AZ91D

In this work, a cast magnesium alloy AZ91D was friction stir processed. Detailed microstructural studies and Gleeble hot ductility tests were conducted on the as-cast and the FSPed samples to comparatively assess their heat-affected zone liquation cracking behavior. The results show that the use of FSP as a pretreatment to fusion welding can strikingly improve the heat-affected zone liquation cracking resistance of alloy AZ91D by reducing the amount and size of the low-melting eutectic β (Mg{sub 17}Al{sub 12}) as well as by refining the matrix grain size.

36 MATERIALS SCIENCE↗

Magnesium Loss in Nd:YAG Pulsed Laser Welding of Aluminum Alloys

In the current investigation, the loss of magnesium (Mg) in Nd:YAG pulsed laser welding of a number of aluminum (Al) alloys was studied both experimentally and numerically. The experimental results showed that at a fixed average laser power, with the increasing pulse frequency, Mg concentration of the weld metals decreased. A numerical model was developed for the calculation of Mg evaporation from the weld pool. The model predicted a trend in the changes of Mg concentration of the weld pool, working best for alloys containing the higher levels of Mg. The calculations showed that with the increasing pulse frequency from 15 to 40 Hz, due to a decrease in the average temperature of the weld pool, Mg loss in terms of mass per unit area of the weld spot actually decreased from 230 × 10{sup −5} to 120 × 10{sup −5} kg/m{sup 2}. However, due to a decrease in the weld penetration/volume, the effective Mg loss of the weld metal in terms of concentration increased from 110 × 10{sup −1} to 260 × 10{sup −1} kg/m{sup 3}. It was shown that due to interactions between Mg and other main alloying elements, the activity coefficient of Mg had to be modified for the model to accurately predict Mg evaporation of the weld pool.

36 MATERIALS SCIENCE↗

Characteristics of the Hot Workability of an AZ91D Magnesium Alloy Using 3D Processing Maps

Hot compression tests were carried out on an a homogenized as-cast AZ91D magnesium alloy at temperatures ranging from 220 °C to 380 °C and strain rates ranging from 0.001 to 10 s{sup −1} by means of a Gleeble-3500 thermo mechanical simulator. True stress-–true strain curves were given. A constitutive modeling of the homogenized alloy was proposed to describe the flow characteristic. The deformation activation energy was estimated to be 142.27 kJ mol{sup −1}. Continuous three-dimensional (3D) processing maps were developed based on the true stress–true strain data as a function of strain, temperature, and strain rate. A detailed interpretation of the established 3D processing maps was conducted. The results showed that the variation of the 3D processing maps was significantly strain dependent. Dynamic recrystallization domains with high-power dissipation efficiencies and instability domains with negative instability coefficient were identified from the 3D power dissipation maps and the 3D instability maps, respectively. It was also revealed that the instability domains distinctly became enlarged with the increasing strain. Optimized temperature and strain rate ranges at various strains were determined. Furthermore, hot workability characteristics were clarified through examining the microstructures obtained under conditions falling within stability and instability domains with various strains. The results proved that the developed 3D processing maps can provide an accurate prediction of the hot deformation behavior for the homogenized AZ91D alloy.

36 MATERIALS SCIENCE↗

Numerical Simulation and Experimental Validation of Nondendritic Structure Formation in Magnesium Alloy Under Oscillation and Ultrasonic Vibration

In this study, the formation of nondendritic structures in the primary phase of magnesium alloy solidified under oscillation and ultrasonic vibration was investigated by numerical simulation and experimentally. The growth and motion of a dendrite during solidification was simulated by a combination of the lattice Boltzmann method and the phase-field method. The simulation and experimental results indicated that higher oscillation amplitudes and acoustic streaming made the microstructures change from dendritic to nondendritic in the α-Mg primary phases. A sufficient shear stress and an appropriate flow time in the barrel should be satisfied when a given inclined angle is selected. The effects of the flow and the thermal field on the nucleation behavior, the constitutional undercooling, and the growth morphology are also discussed. It was found that a high shear rate and high turbulence can help homogenize the temperature and the concentration fields and collide and rotate the α-Mg primary phases.

36 MATERIALS SCIENCE↗

Effect of Cerium Oxide on Morphologies and Electrochemical Properties of Ni-W-P Coating on AZ91D Magnesium

AZ91D magnesium alloy substrate was first pretreated in a phosphoric acid to obtain a phosphate coating, and then, the electroless ternary Ni-W-P coating was deposited using a sulfate nickel bath. The morphologies of the Ni-W-P coating were observed by using scanning electron microscope, the deposition rate of the coating was examined with the method of gravimetric analysis, and the phase analysis was identified by x-ray diffractometer. Electrochemical property was tested by means of an electrochemical analyzer. The results indicated that the addition of an optimum concentration of CeO{sub 2} (cerium oxide) particles could evidently improve the deposition rate and the stability of the plating bath. However, it acted as an inhibiting effect as the concentration of CeO{sub 2} particles exceeded to 8 mg/L in the sulfate nickel bath. The results also revealed that the morphology of Ni-W-P coating became more smooth, compact and uniform with the increase in the concentrations of CeO{sub 2} particles in the bath, but the corrosion resistance decreased due to the precipitation of crystal phases (Ni{sub 3}P, Ni{sub 4}W, etc.) after heat treatment.

36 MATERIALS SCIENCE↗

Mechanical Properties and Corrosion Behavior of As-Cast Mg-Zn-Zr-(La) Magnesium Alloys

The effects of La content on the mechanical properties and corrosion behavior of as-cast Mg-Zn-Zr (ZK) magnesium alloys were investigated. The results showed that La addition to ZK60 alloy resulted in a considerable grain refinement and an increase in the volume fraction of second phases by formation of Mg-Zn-La ternary phase. The tensile tests were performed at both room and elevated temperatures. At room temperature, the yield and tensile strengths and elongation-to-fracture significantly increased with 0.2 wt.% La addition, then deteriorated slightly with increasing La additions above 0.2 wt.%. At 200 °C, the yield and tensile strengths continually improved and elongation-to-fracture decreased with increasing La content due to the presence of thermally stable Mg-Zn-La phase. Immersion and electrochemical corrosion tests revealed that the formation of Mg-Zn-La phases led to a higher amount of cathodic sites and preferential corrosion propagation, and thus a decrease in the corrosion resistance of ZK60 alloys.

36 MATERIALS SCIENCE↗