Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “INLET FLOW”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Dynamics of cavitating cascades

The unsteady dynamics of cavitating cascades and inducer pumps were studied with a view to understanding (and possibly predicting) the dynamic characteristics of these devices. The chronology of the research is summarized as well as the final conculsions for each task. The construction of a dynamic pump test facility and its use in making experimental measurements of the transfer function is described as well as tests conducted using a scale model of the low pressure liquid oxygen turbopump inducer in the shuttle main engine. Auto-oscillation and unsteady inlet flow characteristics are discussed in addition to blade cavity influence and bubbly cavitation.

Brennen, C. E.↗
NASA NTRS1981

Additional testing of the inlets designed for a tandem fan V/STOL nacelle

The wind tunnel testing of a scale model of a tandem fan nacelle designed for a type (subsonic cruise) V/STOL aircraft configuration is discussed. The performance for the isolated front inlet and for the combined front and aft inlets is reported. Model variables include front and aft inlets with aft inlet variations of short and long aft inlet cowls, with a shaft simulator and diffuser vortex generators, cowl lip fillets, and nacelle strakes. Inlet pressure recovery, distortion, and inlet angle-to-attack separation limits were evaluated at tunnel velocity from 0 to 240 knots, angles-of-attack from -10 to +40 degrees and inlet flow rates corresponding to throat Mach number from 0.0 to 0.6. Combined nacelle pitch and yaw runs up to 30 deg. were also made.

Ybarra, A. H.↗
NASA NTRS1980

Forward velocity effects on fan noise and the suppression characteristics of advanced inlets as measured in the NASA-Ames 40 by 80 foot wind tunnel

Forward velocity effects on the forward radiated fan noise and on the suppression characteristics of three advanced inlets relative to a baseline cylindrical inlet were measured in the NASA Ames Research Center 40 x 80 foot Wind Tunnel. A modified JT15D turbofan engine in a quiet nacelle was the source of fan noise; the advanced inlets were a Conventional Takeoff/Landing (CTOL) hybrid inlet, a Short Takeoff/Landing (STOL) hybrid inlet, and a treated deflector inlet. Also measured were the static to flight effects on the fan noise of canting the baseline inlet 4 deg downward to simulate typical wing mounted turbofan engines. The CTOL hybrid inlet suppressed the high tip speed fan noise as much as 18 PNdB on a 61 m (200 ft) sideline scaled to a CF6 size engine while the STOL hybrid inlet suppressed the low tip speed fan noise as much as 13 PNdB on a 61 m (200 ft) sideline scaled to a OCSEE size engine. The deflector inlet suppressed the high tip speed fan noise as much as 13 PNdB at 61 m (200 ft) overhead scaled to a CF6 size engine. No significant changes in fan noise suppression for the CTOL and STOL hybrid inlets occurred for forward velocity changes above 21 m/s (68 ft/s) or for angle of attack changes up to 15 deg. However, changes in both forward velocity and angle of attack changed the deflector inlet noise unpredictably due to the asymmetry of the inlet flow field into the fan.

Moore, M. T.↗
NASA NTRS1982

Measurement and prediction of mean velocity and turbulence structure in the near wake of an airfoil

An experimental investigation of the near wake of a thin airfoil at various incidence angles is reported in this paper. The airfoil (NACA 0012 basic thickness form) was located in a wind tunnel, and the wake structure was measured using hot-wire sensors. The measurements of mean-velocity, turbulence intensity and Reynolds-stress components across the wake at several distances downstream show the complex nature of the near wake and its asymmetrical behavior. The asymmetry in the wake property, which is maintained up to a length of 1.5 chords downstream of the trailing edge of the blade, is dependent on the incidence angle of the inlet flow. The streamwise velocity defect in an asymmetric wake decays more slowly compared to that of a symmetric wake. The streamline curvature due to the blade loading has a substantial effect on the mean velocity profile as well as the turbulence structure. The numerical study of the same wake indicates that the existing turbulence closure models need some modification to account for the asymmetric characteristics of the wake.

Hah, C.↗
NASA NTRS1981

Experimental investigation of tangential blowing for control of the strong shock boundary layer interaction on inlet ramps

A 0.165-scale isolated inlet model was tested in the NASA Lewis Research Center 8-ft by 6-ft Supersonic Wind Tunnel. Ramp boundary layer control was provided by tangential blowing from a row of holes in an aft-facing step set into the ramp surface. Testing was performed at Mach numbers from 1.36 to 1.96 using both cold and heated air in the blowing system. Stable inlet flow was achieved at all Mach numbers. Blowing hole geometry was found to be significant at 1.96M. Blowing air temperature was found to have only a small effect on system performance. High blowing levels were required at the most severe test conditions.

Schwendemann, M. F.↗
NASA NTRS1984

Full load testing in the platform module prior to tow-out: A case history of subsynchronous instability

An electric motor driven centrifugal compressor to supply gas for further compression and reinjection on a petroleum production platform in the North Sea was examined. The compressor design, raised concerns about susceptibility to subsynchronous instability. Log decrement, aerodynamic features, and the experience of other compressors with similar ratios of operating to critical speed ratio versus gas density led to the decision to full load test. Mixed hydrocarbon gas was chosen for the test to meet discharge temperature restrictions. The module was used as the test site. Subsynchronous vibrations made the compressor inoperable above approximately one-half the rated discharge pressure of 14500 kPa. Modifications, which includes shortening the bearing span, change of leakage inlet flow direction on the back to back labyrinth, and removal of the vaned diffusers on all stages were made simultaneously. The compressor is operating with satisfactory vibration levels.

Fulton, J. W.↗
NASA NTRS1985

The effect of aerodynamic and structural detuning on turbomachine supersonic unstalled torsional flutter

The effects of alternate-blade structural detuning and adjacent-blade alternate-circumferential-spacing aerodynamic detuning on the supersonic unstalled torsional flutter stability of a turbomachine rotor are investigated analytically. An unsteady aerodynamic model employing influence coefficients is constructed for the case of a flat-plate-airfoil cascade in torsion-mode harmonic oscillation in a supersonic inviscid isentropic adiabatic irrotational perfect-gas inlet flow with a subsonic leading-edge locus. The influence coefficients and equations of motion are derived; the model is verified by applying it to the 12-blade cascade-B flow geometry studied by Verdon and McCune (1975); and the results are presented graphically. It is found that the rotor can be stabilized over the entire reduced frequency range by applying a combination of structural and aerodynamic detuning as the passive flutter-control mechanism.

Hoyniak, D.↗
NASA NTRS1984

A study of Sabatier reactor operation in zero 'G'

The results of zero-g computer model simulation of the operation of a Sabatier reactor, which relies on the effects of buoyant forces, are presented. The reactor was also operated in an experiment with inlet flow rates of carbon dioxide that correspond to continuous operation of the reactor at three, five, eight, and ten-man loading conditions; the three and five-man conditions are noted to be within the design capabilities of the reactor. The loss of carbon dioxide conversion predicted by the model for zero-g environment is noted to be substantial, ranging from 12 to 18.2 percent for five-man to ten-man loading. The simulated normal-gravity values are within 0.9 percent of the experimental conversions. Finally, the results indicate a much hotter operation of the reactor in zero-g due to the loss of natural convective cooling effect.

Forsythe, R. K.↗
NASA NTRS1986

Experimental investigation of piloted flameholders

Four configurations of piloted flameholders were tested. The range of flame stabilization, flame propagation, pressure oscillation during ignition, and pressure drop of the configurations were determined. Some tests showed a very strong effect of inlet flow velocity profile and flameholder geometry on flame stabilization. These tests led to the following conclusions. (1) The use of a piloted flameholder in the turbofan augmentor may minimize the peak pressure rise during ignition. At the present experimental conditions, delta P/P asterisk over 2 is less than 10 percent; therefore, the use of a piloted flameholder is a good method to realize soft ignition. (2) The geometry of the piloted flameholder and the amount of fuel injected into the flameholder have a strong effect on the pressure oscillation during ignition of the fuel-air mixture in the secondary zone. (3) Compared with the V-gutter flameholder with holes in its wall, the V-gutter flameholder without holes not only has advantages such as simple structure and good rigidity but offers a wide combustion stability limit and a high capability of igniting the fuel-air mixture of the secondary zone.

Guo, C. F.↗
NASA NTRS1987

Experimental Evaluation of Turning Vane Designs for High-speed and Coupled Fan-drive Corners of 0.1-scale Model of NASA Lewis Research Center's Proposed Altitude Wind Tunnel

Two turning vane designs were experimentally evaluated for the fan-drive corner (corner 2) coupled to an upstream diffuser and the high-speed corner (corner 1) of the 0.1 scale model of NASA Lewis Research Center's proposed Altitude Wind Tunnel. For corner 2 both a controlled-diffusion vane design (vane A4) and a circular-arc vane design (vane B) were studied. The corner 2 total pressure loss coefficient was about 0.12 with either vane design. This was about 25 percent less loss than when corner 2 was tested alone. Although the vane A4 design has the advantage of 20 percent fewer vanes than the vane B design, its vane shape is more complex. The effects of simulated inlet flow distortion on the overall losses for corner 1 or 2 were small.

Gelder, Thomas F.↗
NASA NTRS1988

The design and development of transonic multistage compressors

The development of the transonic multistage compressor is reviewed. Changing trends in design and performance parameters are noted. These changes are related to advances in compressor aerodynamics, computational fluid mechanics and other enabling technologies. The parameters normally given to the designer and those that need to be established during the design process are identified. Criteria and procedures used in the selection of these parameters are presented. The selection of tip speed, aerodynamic loading, flowpath geometry, incidence and deviation angles, blade/vane geometry, blade/vane solidity, stage reaction, aerodynamic blockage, inlet flow per unit annulus area, stage/overall velocity ratio, and aerodynamic losses are considered. Trends in these parameters both spanwise and axially through the machine are highlighted. The effects of flow mixing and methods for accounting for the mixing in the design process are discussed.

Ball, C. L.↗
NASA NTRS1989

Nitric acid oxide mixing ratio measurements using a rocket launched chemiluminescent instrument

A total of 18 rocket launched parachute borne nitric oxide instruments were launched from 1977 to 1985. A very precise instrument for the measurement of the nitric oxide mixing ratio was fabricated. No changes were made in the main body of the instruments, i.e., things associated with the reaction volume. Except for the last 4 launches, however, it did not yield the required absolute values that was hoped for. Two major problems were encountered. First, the wrong choice of the background calibration gas, nitrogen, caused the first 10 data sets to be too low in the absolute mixing ratio by nearly the order of 2 to 5 ppbv. The error was realized, and air was substituted for the bias gas measurement. Second, in the desire to extend the measurement to higher altitudes, the problem of contaminating the inlet flow tube with ozone from the reagent gas was encountered. The ozone valve was opened too early in the flight and this caused the pressure in the reaction volume to exceed the pressure at the flow tube entrance, permitting the ozone to migrate backwards. This problem was restricted to an altitude above 45 km.

Horvath, Jack J.↗
NASA NTRS1991

Low-Leakage Inlet Swirl Brake

Improved swirl brake offers both lower rotordynamic instability and lower static-pressure wise. Sixty-four vanes evenly spaced around ring. Convert inlet flow from circumferential to axial.

Scharrer, Joseph K.↗
NASA NTRS1991

Some preliminary results of brush seal/rotor interference effects on leakage at zero and low RPM using a tapered-plug rotor

Some preliminary brush seal leakage results for ambient temperature air are presented. Data for four nominal brush rotor radial clearances of -0.09, -0.048, -0.008, and 0.035 mm were taken by using a tapered plug rotor at 0 and 400 rpm with rotor runout of 0.127 mm peak to peak. The brush seal nominal bore diameter was 38 mm with 0.05 mm bristles at 200 bristles/mm of circumference and a 0.61 mm fence height. Leakages were greater than predicted, but agreement was reasonable. Leakage rates were not significantly altered by hysteresis or inlet flow variations. Visualization studies showed that the bristles followed the 400 rpm excitation, and loading studies indicated that bristles slid relative to one another.

Hendricks, R. C.↗
NASA NTRS1991

Some preliminary results of brush seal/rotor interference effects on leakage at zero and low rpm using a tapered-plug rotor

Some preliminary brush seal leakage results for ambient-temperature air are presented. Data for four nominal brush-rotor radial clearances of -0.09, -0.048, -0.008, and 0.035 mm were taken by using a tapered plug rotor at 0 and 400 rpm with rotor runout of 0.127 mm peak to peak. The brush seal nominal bore diameter was 38 mm with 0.05-mm bristles at 200 bristles/mm of circumference and a 0.61-mm fence height. Leakages were greater than predicted, but agreement was reasonable. Leakage rates were not significantly altered by hysteresis or inlet flow variations. Visualization studies showed that the bristles followed the 400-rpm excitation, and loading studies indicated that bristles slid relative to one another.

Hendricks, R. C.↗
NASA NTRS1991

Supersonic combustion with transverse, circular wall jets

A series of experiments are reported using inclined circular wall jets in rectangular scramjet combustion chambers configured as constant area ducts. A free piston shock tunnel was used to create inlet flow Mach numbers between 4.2 and 5.5, at enthalpies corresponding to flight speeds of between 3.5 and 5.3 km/s. Measurements of duct static pressure levels indicated that significant mixing and combustion was achieved. Using hydrogen as a fuel, it was found that multipoint injection from two sides of the duct gave a larger, and more rapid, pressure rise. In hypersonic flow, it was found that combustion only occurred for the same duct dimensions and operating conditions that supported combustion with central injection from a two-dimensional strut. Wall injection from discrete orifice circular jets was found to be more effective than two-dimensional wall injection across the whole width of the duct.

Morgan, R. G.↗
NASA NTRS1991

An inverse inviscid method for the design of quasi-three dimensional rotating turbomachinery cascades

A new inverse inviscid method suitable for the design of rotating blade sections lying on an arbitrary axisymmetric stream-surface with varying streamtube width is presented. The geometry of the axisymmetric stream-surface and the streamtube width variation with meridional distance, the number of blades, the inlet flow conditions, the rotational speed and the suction and pressure side velocity distributions as functions of the normalized arc-length are given. The flow is considered irrotational in the absolute frame of reference and compressible. The output of the computation is the blade section that satisfies the above data. The method solves the flow equations on a (phi 1, psi) potential function-streamfunction plane for the velocity modulus, W and the flow angle beta; the blade section shape can then be obtained as part of the physical plane geometry by integrating the flow angle distribution along streamlines. The (phi 1, psi) plane is defined so that the monotonic behavior of the potential function is guaranteed, even in cases with high peripheral velocities. The method is validated on a rotating turbine case and used to design new blades. To obtain a closed blade, a set of closure conditions were developed and referred.

Bonataki, E.↗