Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Hydraulic Control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

Development and Flight Test of an Augmented Thrust-Only Flight Control System on an MD-11 Transport Airplane

An emergency flight control system using only engine thrust, called Propulsion-Controlled Aircraft (PCA), has been developed and flight tested on an MD-11 airplane. In this thrust-only control system, pilot flight path and track commands and aircraft feedback parameters are used to control the throttles. The PCA system was installed on the MD-11 airplane using software modifications to existing computers. Flight test results show that the PCA system can be used to fly to an airport and safely land a transport airplane with an inoperative flight control system. In up-and-away operation, the PCA system served as an acceptable autopilot capable of extended flight over a range of speeds and altitudes. The PCA approaches, go-arounds, and three landings without the use of any non-nal flight controls have been demonstrated, including instrument landing system-coupled hands-off landings. The PCA operation was used to recover from an upset condition. In addition, PCA was tested at altitude with all three hydraulic systems turned off. This paper reviews the principles of throttles-only flight control; describes the MD-11 airplane and systems; and discusses PCA system development, operation, flight testing, and pilot comments.

Burcham, Frank W., Jr.↗

Development of Low-Cost Micromanipulation Systems for Small Extraterrestrial Samples

The analysis of microscale to mm-scale astromaterials often involves the transfer of samples from storage or collection substrates to analytical substrates. These transfers are accomplished by hand (via tweezers or fine-tipped needles) or by utilizing micromanipulation instruments. Freehand manipulation of small particles is extremely challenging due to involuntary hand tremors on the order of 100μm and due to the triboelectric charging induced by frequent contact between the manipulation tool and the support substrate. Months or years of practice may be required before an investigator develops the necessary experience to confidently transfer a 10-20μm particle in this manner. Handling even mm-sized particles with fine-tipped tweezers can be challenging, due to the inability to precisely control the force with which grains are being held. Mechanical, hydraulic, and motorized/electrical micromanipulators enable the precise handling of microscale samples and are often utilized in laboratories where frequent small sample preparation is required. However, the price of such instruments (~ $10,000 to $100,000) makes them cost-prohibitive for some institutions. Graduate students or early-career scientists interested in conducting research on interplanetary dust particles, Itokawa particles returned by Hayabusa, or future samples returned by OSIRIS-REx or Hayabusa2 may experience difficulty in justifying the expense of a micromanipulator to their advisors or principle investigators. Johnson Space Center’s Astromaterials Acquisition and Curation Office and the Lunar and Planetary Institute conduct annual training for early career scientists and for investigators that require experience with handling of small extraterrestrial samples. In support of this training, we have been developing low-cost mechanical alternatives to expensive micromanipulators that training participants can implement in their respective facilities.

Snead, Christopher J.↗

RAVEN as a tool for dynamic probabilistic risk assessment: Software overview

RAVEN is a software tool under development at the Idaho National Laboratory (INL) that acts as the control logic driver and post-processing tool for the newly developed Thermal-Hydraulic code RELAP-7. The scope of this paper is to show the software structure of RAVEN and its utilization in connection with RELAP-7. A short overview of the mathematical framework behind the code is presented along with its main capabilities such as on-line controlling/ monitoring and Monte-Carlo sampling. A demo of a Station Black Out PRA analysis of a simplified Pressurized Water Reactor (PWR) model is shown in order to demonstrate the Monte-Carlo and clustering capabilities. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Model-free adaptive control for MHTGR-based nuclear steam supply systems - 144

Modular high temperature gas-cooled reactor (MHTGR) uses helium as coolant and graphite as both moderator and structural materials. Due to its inherent safety feature, MHTGR has been regarded as an important candidate for next generation of nuclear plants. By coupling with the once-through steam generator (OTSG), MHTGR can be utilized to form the nuclear steam supply system (NSSS) for producing superheated steam, which can be adopted for nuclear plants with high efficiency. Power-level control of is important for the stable and efficient operation of the MHTGR-based NSSS, and it is necessary to develop the power-level control law that is robust to physical and thermal parameters and can guarantee the closed-loop stability in normal and even abnormal conditions. In this paper, a model-free adaptive power-level control law is developed for the MHTGR-based NSSS, which is free from physical and thermal-hydraulic parameters, takes the simple forms of proportional-integral (PI) or proportional-differential (PD) feedback law, and can provide globally asymptotic closed-loop stability. Then, it is applied to the NSSS control of the two modular high temperature gas-cooled nuclear plant HTR-PM. Numerical simulation results in normal power maneuver and some typical abnormal cases show that this new control law can provide satisfactory closed-loop stability as well as transient performance. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Illustration of VERA Capabilities to Model a Typical iPWR SMR

Small modular reactors (SMRs) are being considered by the commercial nuclear power industry as an option for more distributed generation and for replacement of older fossil fuel generating facilities. SMRs are more compact than operating pressurized water reactors (PWRs), producing about 200 MWe as compared to 1000 MWe or higher for their full-sized cousins, and are offered as “expandable” units; that is, their modular design allows the utility to add more units progressively at the same site. In Summer 2014, CASL reported on a progression of demonstrations illustrating VERA’s ability to simulate a typical SMR of the iPWR type, while developing a simple core cycle design for cycle economic studies. The work included development of fuel assembly lattices, 3D single assembly and full core (quarter symmetry) simulations of the proposed core cycle design using the CASL Virtual Environment for Reactor Applications (VERA). The report concluded that it would be difficult for the SMR to operate for the target 1400 EFPD cycle length and that the fuel cost would be on the order of 50% higher as compared with a PWR. Unfortunately, the Reference 4 core cycle design did not include control component management. The iPWR is intended to be operated using the control rods for reactivity control, as opposed to using soluble boron (like most currently operating PWRs), and the introduction of the control rods is expected to affect the length of the cycle. Therefore, this work continues the previous CASL demonstration of VERA capability to simulate a typical iPWR core, including the development of a control component management strategy using the Reference 4 core design and utilizing the soon-to-be released VERA3.3 tools. Note that this study is not intended as a validation study; rather it is merely an illustration of VERA’s capabilities to simulate a typical iPWR. Simulations included two variations on control rod banks – a two-bank scheme and a ten-bank scheme. Both schemes were modelled using the VERA Common Input, and more than six iterations on each control rod scheme were simulated to arrive at a combination of rod banks and insertion depths that provided a core reactivity near the target k eff of 1.000 ± 0.001 (more than 50 cases run) over two calendar months. In particular, VERA was used to determine the hot excess reactivity for the core design with all rods out (ARO), and then iterative simulations with the rod banks inserted to determine the critical control rod bank positions were completed. VERA options to simplify the process were exercised as possible, particularly restart functionality, coupled thermal-hydraulics using the internal T-H solver, xenon, and depletion capability. The fuel shuffling functionality was not exercised, since the iPWR SMR features a once-through cycle. The VERA method of characteristics (MOC) neutronics subcomponent was used to predict power and reactivity with control rod maneuvering, both with and without thermal-hydraulic feedback. The problem was scaled from 35 CPU cores to 3815, effectively demonstrating the solution time with respect to computing capacity. Computer clusters at Oak Ridge National Laboratory, Idaho National Laboratory and Tennessee Valley Authority were used. These studies provide an additional illustration of the application of VERA to a typical iPWR SMR. Reference 4 previously demonstrated that the codes could handle the differences in geometry for the iPWR, and this study expanded the illustration to include control rod management. Further, the work illustrates the need for in-depth simulations to support effective control rod maneuvering for an iPWR and highlights the need for control rod reactivity search capability within VERA. Additionally, the development of a control rod bank reactivity search capability will be extremely useful for not only this application, but also for BWRs as CASL develops BWR capability in Phase 2.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Design of H2-O2 space shuttle APU. Volume 1: APU design

The H2-O2 space shuttle auxiliary power unit (APU) program is a NASA-Lewis effort aimed at hardware demonstration of the technology required for potential use on the space shuttle. It has been shown that a hydrogen-oxygen power unit (APU) system is an attractive alternate to the space shuttle baseline hydrazine APU system for minimum weight. It has the capability for meeting many of the heat sink requirements for the space shuttle vehicle, thereby reducing the amount of expendable evaporants required for cooling in the baseline APU. Volume 1 of this report covers preliminary design and analysis of the current reference system and detail design of the test version of this reference system. Combustor test results are also included. Volume 2 contains the results of the analysis of an initial version of the reference system and the computer printouts of system performance. The APU consists of subsystems for propellant feed and conditioning, turbopower, and control. Propellant feed and conditioning contains all heat exchangers, valves, and the combustor. The turbopower subsystem contains a two-stage partial-admission pressure-modulated, 400-hp, 63,000-rpm turbine, a 0-to 4-g lubrication system, and a gearbox with output pads for two hydraulic pumps and an alternator (alternator not included on test unit). The electronic control functions include regulation of speed and system temperatures; and start-and-stop sequences, overspeed (rpm) and temperature limits, failsafe provisions, and automatic shutdown provisions.

Harris, E.↗

Data-Driven, In Situ, Relative Sensor Calibration Based on Waveform Fitting Moment Tensor Inversion

This article presents a deconvolution-based methodology for the relative calibration of acoustic emission sensors. The method uses the observations from multiple acoustic emission arrivals to estimate correction functions that account for instrument response and site effects. The corrections act on the measurements reshaping the wave arrivals, in many cases allowing visible discrimination between compressional and shear phases. The methodology is illustrated with the application on a dataset obtained during the hydraulic fracturing at triaxial stress conditions of a Colton sandstone block. A workflow for the estimation of full moment tensor solutions, including the generation of quality control attributes complements the presentation. The moment tensor solutions display fracture geometries mostly aligned with the main hydraulic fracture’s plane. The style of activation can be associated with an extensive stress regime before breakdown and to a compressional stress regime after breakdown, when the pumps were reversed to withdraw fluid from the block. In conclusion, the source types commonly deviate from the pure double-couple type; however, the deviations are under 30° in the case of opening fractures, and under 20° in the case of closing fractures. Therefore, the acoustic emissions in this experiment are the result of predominantly shearing dislocations.

47 OTHER INSTRUMENTATION↗

A High-Efficient Solution for Electro-Hydraulic Actuators with Energy Regeneration Capability

This paper proposes a cost-effective, robustly practical solution for a high-efficient electro-hydraulic actuator (EHA) for linear drives. The solution addresses the challenges of high costs and limited efficiency that limit the application of EHA for the electrification of many off-road vehicles. Based on a variable-speed electric motor and a low-cost technology for a fixed-displacement pump, the proposed solution is suitable for a compact implementation and it is capable of energy regeneration under overrunning load conditions. Two different architectures—an open circuit and a closed circuit one—are considered to determine the most practical and efficient configuration as well as the control features. Both architectures minimize throttling losses associated with the conventional regulation of hydraulic actuators. Actuator velocities below the minimum and beyond the maximum allowable pump flow rate are achieved in both architectures using a proportional valve that bypasses the pump flow. The paper describes the design methodology as well as the simulation and experimental activities performed to verify the control strategies as well as energy efficiency. Considering an EHA system of about 20 kW, a complete efficiency map of the system is determined for all the possible four quadrants of operation thus including both resistive and overrunning loads, where energy recuperation is implemented. Simulation and experimental results show that the energy efficiency of the hydraulic systems can reach 84.7% in resistive phases. In assistive phases, the hydraulic system can recover up to 81.8% of the actuator energy. Here, the comparison between open-circuit and closed-circuit structures shows the advantages of the former in terms of energy efficiency. The proposed solution is suitable for electrified hydraulic actuation systems, in both industrial and mobile applications. With the advantages of the low cost of the hydraulic unit and high energy efficiency, it is particularly suitable for mobile applications such as construction machines, that are recently experiencing a significant electrification trend.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Index tests for geosynthetic clay liners containing bentonite–polymer composites

The hydraulic conductivity of geosynthetic clay liners (GCLs) containing bentonite–polymer composites (BPCs) is controlled by a pore clogging mechanism related to the swelling of sodium bentonite (NaB) granules and formation of polymer gel in the pore space. Three index testing procedures that are influenced by bentonite swelling and rheology of the polymer gel were evaluated in this study for screening BPC GCLs for hydraulic conductivity: viscosity, liquid limit by fall-cone penetration and active water content. Experiments were conducted using polyacrylamide (PAM) polymer, dry-blended mixtures of PAM and NaB and a BPC from a commercially available GCL. These materials were contacted with inorganic solutions representing leachates from a range of waste containment scenarios. For the BPC that was evaluated, hydraulic conductivities less than 10 -10 m/s were obtained when the viscosity exceeded 220 mPa s and the active water content exceeded 300%. Hydraulic conductivities less than 10 -11 m/s were achieved for viscosity exceeding 350 mPa s, fall-cone liquid limit exceeding 190 and active water content exceeding 300%. Additional testing is needed to assess the generality of these index tests and the identified thresholds when applied to other BPC GCLs and other permeant liquids.

Engineering↗

Characterizing the Impact of Fractured Caprock Heterogeneity on Supercritical CO 2 Injection

We present a set of multiphase flow simulations where supercritical CO 2 (scCO 2 ) displaces water at hydrostatic conditions within three-dimensional discrete fracture networks that represent paths for potential leakage through caprock above CO 2 storage reservoirs. The simulations are performed to characterize and compare the relative impact of hydraulic and structural heterogeneity in fractured media on the initial movement of scCO 2 through these caprock formations. In one scenario, intrinsic fracture permeabilities are varied stochastically within a fixed network structure. In another scenario, we generate multiple independent, identically distributed network realizations with varying fracture network densities to explore a wide range of geometric and topological configurations. Analysis of the simulations indicates that network structure, specifically connectivity and the presence of hanging fractures, plays a larger role in controlling the displacement of water by scCO 2 than variations in local hydraulic properties. Finally, we identify active surface area of the network as a single-phase feature that could provide a lower bound on the percentage of the network surface area reached by scCO 2 .

54 ENVIRONMENTAL SCIENCES↗

Water and vapor transport in algal‐fungal lichen: Modeling constrained by laboratory experiments, an application for Flavoparmelia caperata

ABSTRACT Algal‐fungal symbionts share water, nutrients, and gases via an architecture unique to lichens. Because lichen activity is controlled by moisture dynamics, understanding water transport is prerequisite to understand their fundamental biology. We propose a model of water distributions within foliose lichens governed by laws of fluid motion. Our model differentiates between water stored in symbionts, on extracellular surfaces, and in distinct morphological layers. We parameterize our model with hydraulic properties inverted from laboratory measurements of Flavoparmelia caperata and validate for wetting and drying. We ask: (1) Where is the bottleneck to water transport? (2) How do hydration and dehydration dynamics differ? and (3) What causes these differences? Resistance to vapor flow is concentrated at thallus surfaces and acts as the bottleneck for equilibrium, while internal resistances are small. The model captures hysteresis in hydration and desiccation, which are shown to be controlled by nonlinearities in hydraulic capacitance. Muting existing nonlinearities slowed drying and accelerated wetting, while exaggerating nonlinearities accelerated drying and slowed wetting. The hydraulic nonlinearity of F. caperata is considerable, which may reflect its preference for humid and stable environments. The model establishes the physical foundation for future investigations of transport of water, gas, and sugar between symbionts.

Potkay, Aaron↗

Responses of two semiarid conifer tree species to reduced precipitation and warming reveal new perspectives for stomatal regulation

Here, relatively anisohydric species are predicted to be more predisposed to hydraulic failure than relatively isohydric species, as they operate with narrower hydraulic safety margins. We subjected co-occurring anisohydric Juniperus monosperma and isohydric Pinus edulis trees to warming, reduced precipitation, or both, and measured their gas exchange and hydraulic responses. We found that reductions in stomatal conductance and assimilation by heat and drought were more frequent during relatively moist periods, but these effects were not exacerbated in the combined heat and drought treatment. Counter to expectations, both species exhibited similar gs temporal dynamics in response to drought. Further, whereas P. edulis exhibited chronic embolism, J. monosperma showed very little embolism due to its conservative stomatal regulation and maintenance of xylem water potential above the embolism entry point. This tight stomatal control and low levels of embolism experienced by juniper refuted the notion that very low water potentials during drought are associated with loose stomatal control and with the hypothesis that anisohydric species are more prone to hydraulic failure than isohydric species. Because direct association of stomatal behaviour with embolism resistance can be misleading, we advocate consideration of stomatal behaviour relative to embolism resistance for classifying species drought response strategies.

54 ENVIRONMENTAL SCIENCES↗

Advanced Seismic While Drilling System

A breakthrough has been discovered for controlling seismic sources to generate selectable low frequencies. Conventional seismic sources, including sparkers, rotary mechanical, hydraulic, air guns, and explosives, by their very nature produce high-frequencies. This is counter to the need for long signal transmission through rock. The patent pending SeismicPULSER{trademark} methodology has been developed for controlling otherwise high-frequency seismic sources to generate selectable low-frequency peak spectra applicable to many seismic applications. Specifically, we have demonstrated the application of a low-frequency sparker source which can be incorporated into a drill bit for Drill Bit Seismic While Drilling (SWD). To create the methodology of a controllable low-frequency sparker seismic source, it was necessary to learn how to maximize sparker efficiencies to couple to, and transmit through, rock with the study of sparker designs and mechanisms for (a) coupling the sparker-generated gas bubble expansion and contraction to the rock, (b) the effects of fluid properties and dynamics, (c) linear and non-linear acoustics, and (d) imparted force directionality. After extensive seismic modeling, the design of high-efficiency sparkers, laboratory high frequency sparker testing, and field tests were performed at the University of Texas Devine seismic test site. The conclusion of the field test was that extremely high power levels would be required to have the range required for deep, 15,000+ ft, high-temperature, high-pressure (HTHP) wells. Thereafter, more modeling and laboratory testing led to the discovery of a method to control a sparker that could generate low frequencies required for deep wells. The low frequency sparker was successfully tested at the Department of Energy Rocky Mountain Oilfield Test Center (DOE RMOTC) field test site in Casper, Wyoming. An 8-in diameter by 26-ft long SeismicPULSER{trademark} drill string tool was designed and manufactured by TII. An APS Turbine Alternator powered the SeismicPULSER{trademark} to produce two Hz frequency peak signals repeated every 20 seconds. Since the ION Geophysical, Inc. (ION) seismic survey surface recording system was designed to detect a minimum downhole signal of three Hz, successful performance was confirmed with a 5.3 Hz recording with the pumps running. The two Hz signal generated by the sparker was modulated with the 3.3 Hz signal produced by the mud pumps to create an intense 5.3 Hz peak frequency signal. The low frequency sparker source is ultimately capable of generating selectable peak frequencies of 1 to 40 Hz with high-frequency spectra content to 10 kHz. The lower frequencies and, perhaps, low-frequency sweeps, are needed to achieve sufficient range and resolution for realtime imaging in deep (15,000 ft+), high-temperature (150 C) wells for (a) geosteering, (b) accurate seismic hole depth, (c) accurate pore pressure determinations ahead of the bit, (d) near wellbore diagnostics with a downhole receiver and wired drill pipe, and (e) reservoir model verification. Furthermore, the pressure of the sparker bubble will disintegrate rock resulting in an increased overall rates of penetration. Other applications for the SeismicPULSER{trademark} technology are to deploy a low-frequency source for greater range on a wireline for Reverse Vertical Seismic Profiling (RVSP) and Cross-Well Tomography. Commercialization of the technology is being undertaken by first contacting stakeholders to define the value proposition for rig site services utilizing SeismicPULSER{trademark} technologies. Stakeholders include national oil companies, independent oil companies, independents, service companies, and commercial investors. Service companies will introduce a new Drill Bit SWD service for deep HTHP wells. Collaboration will be encouraged between stakeholders in the form of joint industry projects to develop prototype tools and initial field trials. No barriers have been identified for developing, utilizing, and exploiting the low-frequency SeismicPULSER{trademark} source in a variety of applications. Risks will be minimized since Drill Bit SWD will not interfere with the drilling operation, and can be performed in a relatively quiet environment when the pumps are turned off. The new source must be integrated with other Measurement While Drilling (MWD) tools. To date, each of the oil companies and service companies contacted have shown interest in participating in the commercialization of the low-frequency SeismicPULSER{trademark} source. A technical paper has been accepted for presentation at the 2009 Offshore Technology Conference (OTC) in a Society of Exploration Geologists/American Association of Petroleum Geophysicists (SEG/AAPG) technical session.

02 PETROLEUM↗

Investigation of creep by use of closed loop servo-hydraulic test system

Creep tests were conducted by means of a closed loop servo-controlled materials test system. These tests are different from the conventional creep tests in that the strain history prior to creep may be carefully monitored. Tests were performed for aluminum alloy 6061-0 at 150 C and monitored by a PDP 11/04 minicomputer at a preset constant plastic-strain rate prehistory. The results show that the plastic-strain rate prior to creep plays a significant role in creep behavior. The endochronic theory of viscoplasticity was applied to describe the observed creep curves. The concepts of intrinsic time and strain rate sensitivity function are employed and modified according to the present observation.

Wu, H. C.↗

Feedback from Reactor Internals Segmentation Projects in Europe - 19141

Westinghouse has accumulated significant know-how in the reactor dismantling activities. The approach to internals segmentation and packaging has been continuously enhanced by incorporating lessons learned and best practices into each successive project. Building on the most recent successful experience at Jose Cabrera in Spain, Westinghouse has won several major awards with 13 reactors currently under contract at Chooz A (France), Barsebaeck 1-2 (Sweden), Bohunice V1 (two units in Slovakia), Neckarwestheim I, Philippsburg 1, and more recently at Unterweser, Grafenrheinfeld, Grohnde, Isar 1, Isar 2, Brokdorf (Germany). The primary challenges of a segmentation and packaging project are to separate the highly activated materials from the less-activated materials and package them into appropriate containers for disposal. The choice of the optimum cutting technology is important for a successful project implementation and depends on some specific constraints like disposal costs, project schedule, available work areas or safety. The selected technology for all recent Westinghouse projects is mechanical cutting with different types of designed cutting equipment (hydraulic shears, band saw, disc saw). All segmentation tools are remotely controlled due to the high radiation levels and ALARA and personal safety is the number one priority during the challenging site work. Training on mock-ups in the Westinghouse facility before going to the site is a very important step in order to optimize all procedures and thereby maximize the efficiency on site in order to finalize the project on time or before. The work covers the segmentation of reactor internals but also, in some cases, some replaced components during plant operation that were stored in the spent fuel pool. The cutting equipment proved to be reliable and flexible which is very valuable for the execution of such a challenging project. The Barsebaeck Unit 2 site work has been finished end of October 2017 and its lessons learned are taken into consideration for future activities. Site work is currently on-going simultaneously at Chooz A, Barsebaeck 1, Neckarwestheim I and Philippsburg 1. This paper will provide an overview of all these on-going segmentation projects and will focus on feedback from the first projects executed on site. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Actuator Exerts Tensile Or Compressive Axial Load

Compact, manually operated mechanical actuator applies controlled, limited tensile or compressive axial force. Designed to apply loads to bearings during wear tests in clean room. Intended to replace hydraulic actuator. Actuator rests on stand and imparts axial force to part attached to clevis inside or below stand. Technician turns control screw at one end of lever. Depending on direction of rotation of control screw, its end of lever driven downward (for compression) or upward (for tension). Lever pivots about clevis pin at end opposite of control screw; motion drives downward or upward link attached via shearpin at middle of lever. Link drives coupling and, through it, clevis attached to part loaded.

Nozzi, John↗

Remotely Adjustable Hydraulic Pump

Outlet pressure adjusted to match varying loads. Electrohydraulic servo has positioned sleeve in leftmost position, adjusting outlet pressure to maximum value. Sleeve in equilibrium position, with control land covering control port. For lowest pressure setting, sleeve shifted toward right by increased pressure on sleeve shoulder from servovalve. Pump used in aircraft and robots, where hydraulic actuators repeatedly turned on and off, changing pump load frequently and over wide range.

Kouns, H. H.↗