Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “GANs”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

III-Nitride p-down green (520 nm) light emitting diodes with near-ideal voltage drop

We demonstrate p-down green emitting LEDs with low turn-on voltage enabled by efficient tunnel junctions. Due to the polarization field alignment in the (In,Ga)N/GaN interface with the p-down orientation, the electrostatic depletion barrier for electron and hole injection is reduced when compared with the conventional p-up LEDs. A single (In,Ga)N/GaN heterostructure quantum well active region with a GaN homojunction tunnel junction exhibited very low forward operating voltage of 2.42 V at 20 A/cm 2 with a peak electroluminescence emission wavelength of 520 nm for current densities above 100 A/cm 2 . Furthermore, the bottom tunnel junction with minimal voltage drop enabled excellent hole injection into the bottom p-GaN layer.

36 MATERIALS SCIENCE↗

Increasing the mobility and power-electronics figure of merit of AlGaN with atomically thin AlN/GaN digital-alloy superlattices

Alloy scattering in random AlGaN alloys drastically reduces the electron mobility and, therefore, the power-electronics figure of merit. As a result, Al compositions greater than 75% are required to obtain even a twofold increase in the Baliga figure of merit compared to GaN. However, beyond approximately 80% Al composition, donors in AlGaN undergo the DX transition, which makes impurity doping increasingly more difficult. Moreover, the contact resistance increases exponentially with the increase in Al content, and integration with dielectrics becomes difficult due to the upward shift of the conduction band. Atomically thin superlattices of AlN and GaN, also known as digital alloys, are known to grow experimentally under appropriate growth conditions. These chemically ordered nanostructures could offer significantly enhanced figure of merit compared to their random alloy counterparts due to the absence of alloy scattering, as well as better integration with contact metals and dielectrics. In this work, we investigate the electronic structure and phonon-limited electron mobility of atomically thin AlN/GaN digital-alloy superlattices using first-principles calculations based on density-functional and many-body perturbation theory. The bandgap of the atomically thin superlattices reaches 4.8 eV, and the in-plane (out-of-plane) mobility is 369 (452) cm 2 V -1 s -1 . Using the modified Baliga figure of merit that accounts for the dopant ionization energy, here we demonstrate that atomically thin AlN/GaN superlattices with a monolayer sublattice periodicity have the highest modified Baliga figure of merit among several technologically relevant ultra-wide bandgap materials, including random AlGaN, β-Ga 2 O 3 , cBN, and diamond.

36 MATERIALS SCIENCE↗

Wide bandgap semiconductor materials and devices

The technological and societal impacts of electronic devices based on Ge, Si, and compound semiconductors like GaAs have been profound, fueling the decades long quest in identifying ever-larger bandgap semiconductors to untap new applications and possibilities. Specifically, an increase in the bandgap leads to shorter wavelength emission and an increased breakdown electric field, which has direct consequences for solid-state lighting like light-emitting diodes (LEDs) and laser diodes (LDs) from the visible (blue-green, blue, and violet) and beyond (UV and deep-UV) spectral range and for radically improved power devices supported by a higher intrinsic breakdown strength. Wide bandgap (WBG) semiconductors represent the frontier of materials that satisfy these criteria and include group IV, III–V, and II–VI material families like SiC (3.2 eV), GaN (3.4 eV), and ZnO (3.4 eV), respectively. With even larger bandgaps exceeding 4 eV, ultrawide bandgap (UWBG) semiconductors include diamond, III-nitrides incorporating Al and B (e.g., AlN, BN, and AlGaN), and sesquioxides like Ga 2 O 3 and (Al,Ga) 2 O 3 . These materials span widely varying stages of technological maturity, with SiC and GaN platforms among the most mature with commercially available devices in RF and high-power electronics, while other platforms such as Ga 2 O 3 rapidly advancing and poised to enable new UV and deep-UV optoelectronic devices. This Special Topic on Wide Bandgap Semiconductor Materials and Devices covers broad research subtopics on WBG and UWBG materials that span bulk crystals, epitaxy and substrate technologies, fundamental defect science, and doping, as well as electronic and optoelectronic device fabrication and characterization. Here, we highlight works from the collection, which we categorize by material platform of SiC, III-nitrides, and Ga 2 O 3 and related alloys.

36 MATERIALS SCIENCE↗

High-density polarization-induced 2D electron gases in N-polar pseudomorphic undoped GaN/Al 0.85 Ga 0.15 N heterostructures on single-crystal AlN substrates

The polarization difference and band offset between Al(Ga)N and GaN induce two-dimensional (2D) free carriers in Al(Ga)N/GaN heterojunctions without any chemical doping. A high-density 2D electron gas (2DEG), analogous to the recently discovered 2D hole gas in a metal-polar structure, is predicted in a N-polar pseudomorphic GaN/Al(Ga)N heterostructure on unstrained AlN. We report the observation of such 2DEGs in N-polar undoped pseudomorphic GaN/AlGaN heterostructures on single-crystal AlN substrates by molecular beam epitaxy. With a high electron density of ~4.3 ×10 13 /cm 2 that maintains down to cryogenic temperatures and a room temperature electron mobility of ~450 cm 2 /V s, a sheet resistance as low as ~320 Ω/$\Box$ is achieved in a structure with an 8 nm GaN layer. Finally, these results indicate significant potential of AlN platform for future high-power RF electronics based on N-polar III-nitride high electron mobility transistors.

42 ENGINEERING↗

Transport properties of polarization-induced 2D electron gases in epitaxial AlScN/GaN heterojunctions

AlScN is attractive as a lattice-matched epitaxial barrier layer for incorporation in GaN high electron mobility transistors due to its large dielectric constant and polarization. The transport properties of polarization-induced two-dimensional (2D) electron gas of densities of ∼2×10 13 /cm 2 formed at the AlScN–GaN interface is studied by Hall-effect measurements down to cryogenic temperatures. The 2D electron gas densities exhibit mobilities limited to ∼300 cm 2 /V s down to 10 K at AlScN/GaN heterojunctions. The insertion of a ∼2 nm AlN interlayer boosts the room temperature mobility by more than five times from ∼300 cm 2 /V s to ∼1573 cm 2 /V s, and the 10 K mobility by more than 20 times to ∼6980 cm 2 /V s at 10 K. These measurements provide guidelines to the limits of electron conductivities of these highly polar heterostructures.

42 ENGINEERING↗

Green-emitting cubic GaN/In 0.16 Ga 0.84 N/GaN quantum well with 32% internal quantum efficiency at room temperature

Structural and optical properties of a green-emitting cubic (i.e., zinc blende) GaN/In 0.16 Ga 0.84 N/GaN single quantum well structure are reported. The active layer is grown on a phase-pure (i.e., 100%) cubic GaN enabled on a 1 × 1 cm 2 U-grooved silicon (100) through aspect ratio phase trapping. Energy dispersive x-ray spectroscopy combined with room temperature cathodoluminescence reveals 522 nm green light emission at room temperature with only 16.0% ± 1.6% of indium content, which is ~30% less than the amount of indium needed in a traditional green-emitting hexagonal (i.e., wurtzite) well. Temperature-dependent behavior of the green emission, such as activation energy, s-shaped peak energy shift, and linewidth, is reported. Cathodoluminescence at 8 and 300 K reveals an internal quantum efficiency of 32.0% ± 0.6%, which is higher than any reported value for cubic wells. Altogether, phase-pure cubic active layers on phase transition cubic GaN are shown to be promising for green and longer wavelength emitters.

42 ENGINEERING↗

Effects of structural defects on optical properties of In x Ga 1-x N layers and quantum wells

This review concentrates on the microstructure of In x Ga 1-x N layers and quantum wells (QWs) in relation to their optical properties. The microstructure of In x Ga 1-x N, with a constant In(x) concentration, shifts with layer thickness. Only layers below 100 nm for x = 0.1 are nearly defect-free. A photoluminescence peak is observed at 405 nm, in line with ~10% In, suggesting band-edge luminescence. Layers with greater thickness and In content present a corrugated surface with numerous structural defects, including V-defects, causing redshifts and multi-peaks in photoluminescence up to 490 nm. These defects, resembling those in GaN, lead to a corrugated sample surface. Atomic force microscopy shows a 3.7-fold larger corrugation in samples with 20 QWs compared to those with 5 QWs measured on 2 × 2 μm 2 areas. Like in GaN, dual growth on different crystallographic planes results in varied QW thicknesses, influencing optical traits of devices made from In x Ga 1-x N layers. The purpose of this review and the chosen subject is to highlight the significant contribution of Wladek Walukiewicz and his group to the current research on the properties of In x Ga 1-x N, which are crucial alloys in the field of optoelectronics.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

High conductivity coherently strained quantum well XHEMT heterostructures on AlN substrates with delta doping

Polarization-induced two-dimensional electron gases (2DEGs) in AlN/GaN/AlN quantum well high-electron-mobility transistors on ultrawide bandgap AlN substrates offer a promising route to advance microwave and power electronics with nitride semiconductors. The electron mobility in thin GaN quantum wells embedded in AlN is limited by high internal electric field and the presence of undesired polarization-induced two-dimensional hole gases (2DHGs). To enhance the electron mobility in such heterostructures on AlN, previous efforts have resorted to thick, relaxed GaN channels with dislocations. In this work, we introduce n-type compensation δ-doping in a coherently strained single-crystal (Xtal) AlN/GaN/AlN heterostructure to counter the 2DHG formation at the GaN/AlN interface, and simultaneously lower the internal electric field in the well. This approach yields a δ-doped XHEMT structure with a high 2DEG density of ∼3.2×1013 cm−2 and a room temperature (RT) mobility of ∼855 cm2/Vs, resulting in the lowest RT sheet resistance 226.7 Ω/□ reported to date in coherently strained AlN/GaN/AlN HEMT heterostructures on the AlN platform.

Physics↗

THz cyclotron resonance of a 2D hole gas in a GaN/AlN heterostructure

The recent discovery of highly conducting two-dimensional hole gases (2DHGs) in GaN/AlN heterojunctions has opened the door to efficient complementary GaN electronics, a long-standing challenge in wide-bandgap semiconductor device physics. Electrical transport studies and simulations indicate that both heavy- and light-hole valence bands are occupied in these 2DHGs, but direct experimental characterization of the fundamental parameters of the mobile holes remains at an early stage. Here, we use time-domain terahertz spectroscopy and pulsed magnetic fields up to 31 T to directly measure cyclotron resonance of the mobile 2D holes in these GaN-based 2DHGs at low temperature (8 K), revealing key material properties including effective masses, densities, scattering times, and mobilities.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Origin of proton irradiation-induced deep acceptors in Al 0.70 Ga 0.30 N

Deep level defect introduction and carrier removal were characterized using steady-state photocapacitance (SSPC), deep level transient spectroscopy (DLTS) and lighted capacitance–voltage for proton irradiated n-type Al 0.70 Ga 0.30 N Schottky diodes grown by metal-organic vapor phase epitaxy on AlN-on-sapphire templates. SSPC observed deep levels in the as-grown diode with zero-phonon transition energies of 2.20, 2.65, 3.10, 3.40, and 4.65 eV relative to the conduction band minimum (E c ), and an additional deep level emerged at 1.20 eV with irradiation. Lighted capacitance–voltage measurements quantified the deep level concentration (N t ) of states detected by SSPC, and it was observed that N t increased with proton fluence only for the 1.2 and 4.65 eV levels. Carrier removal was much larger than the increase in N t of the 1.2 and 4.65 eV deep levels, suggesting that radiation-induced deep level compensators existed beyond what was detected with SSPC. DLTS detected additional, proton-induced deep acceptors at E c —0.55, 0.82, and 1.16 eV, the latter of which is likely the same 1.20 eV deep state observed by SSPC. The concentration of the E c —0.82 eV defect state was large enough to reconcile carrier removal with total deep level introduction. Comparing the E c —0.82 and 1.16 eV deep acceptor levels to previous experimental and theoretical reports suggests that their atomistic origins could be the nitrogen vacancy (V N ) and oxygen substituting on the nitrogen sub-lattice (O N ), respectively. This defect behavior contrasts starkly with GaN, where V N and O N are shallow donors, and demonstrates that the electronic properties of defects can evolve drastically within the AlGaN alloy system ranging from wide bandgap GaN to ultra-wide bandgap AlN.

Armstrong, Andrew Michael [Sandia National Laborat↗

Heavy ion irradiation induced failure of gallium nitride high electron mobility transistors: effects of in-situ biasing

Abstract While radiation is known to degrade AlGaN/GaN high-electron-mobility transistors (HEMTs), the question remains on the extent of damage governed by the presence of an electrical field in the device. In this study, we induced displacement damage in HEMTs in both ON and OFF states by irradiating with 2.8 MeV Au 4+ ion to fluence levels ranging from 1.72 × 10 10 to 3.745 × 10 13 ions cm −2 , or 0.001–2 displacement per atom (dpa). Electrical measurement is done in situ , and high-resolution transmission electron microscopy (HRTEM), energy dispersive x-ray (EDX), geometrical phase analysis (GPA), and micro-Raman are performed on the highest fluence of Au 4+ irradiated devices. The selected heavy ion irradiation causes cascade damage in the passivation, AlGaN, and GaN layers and at all associated interfaces. After just 0.1 dpa, the current density in the ON-mode device deteriorates by two orders of magnitude, whereas the OFF-mode device totally ceases to operate. Moreover, six orders of magnitude increase in leakage current and loss of gate control over the 2-dimensional electron gas channel are observed. GPA and Raman analysis reveal strain relaxation after a 2 dpa damage level in devices. Significant defects and intermixing of atoms near AlGaN/GaN interfaces and GaN layer are found from HRTEM and EDX analyses, which can substantially alter device characteristics and result in complete failure.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Phonon Screening of Excitons in Atomically Thin Semiconductors

Atomically thin semiconductors, encompassing both 2D materials and quantum wells, exhibit a pronounced enhancement of excitonic effects due to geometric confinement. Consequently, these materials have become foundational platforms for the exploration and utilization of excitons. Recent ab initio studies have demonstrated that phonons can substantially screen electron-hole interactions in bulk semiconductors and strongly modify the properties of excitons. While excitonic properties of atomically thin semiconductors have been the subject of extensive theoretical investigations, the role of phonon screening on excitons in atomically thin structures remains unexplored. In this Letter, we demonstrate via ab initio GW-Bethe-Salpeter equation calculations that phonon screening can have a significant impact on optical excitations in atomically thin semiconductors. We further show that the degree of phonon screening can be tuned by structural engineering. We focus on atomically thin GaN quantum wells embedded in AlN and identify specific phonons in the surrounding material, AlN, that dramatically alter the lowest-lying exciton in monolayer GaN via screening. Our studies provide new intuition beyond standard models into the interplay among structural properties, phonon characteristics, and exciton properties in atomically thin semiconductors, and have implications for future experiments.

2-dimensional systems↗

Adaptive Time-Division Multiplexing Driving System for Solid State Lighting with Multiple Tunable Channels

Next generation solid state lighting enables unlimited control of light and serve much broader functions beyond the basic lighting for illuminance. The emerging lighting for productivity, well-being, healthcare, and growth have revolutionized the scope of lighting. To empower this unlimited controllability, a multi-channel tunable power-electronics driver is essential but has not been satisfactorily addressed so far. Existing solutions are lossy, large, and expensive, due to introduction of additional buck power conversion stages. This paper proposes a time-division multiplexing (TDM) LED driving system which eliminates those buck stages. The proposed design can directly pair with off-the-shelf pulse width modulated (PWM) controllers and since it inherits entire feature sets, it can achieve low loss at standby and at dimmed condition. The simple analog implementation avoids usage of expensive DSPs/MCU. GaN’s high switching frequency capability can push up the multiplexing frequency so a GaN-based flyback was built and proved the concept.

Xue, Lincoln↗

FL-DISCO: Federated Generative Adversarial Network for Graph-based Molecule Drug Discovery: Special Session Paper

The outbreak of the global COVID-19 pandemic emphasizes the importance of collaborative drug discovery for high effectiveness; however, due to the stringent data regulation, data privacy becomes an imminent issue needing to be addressed to enable collaborative drug discovery. In addition to the data privacy issue, the efficiency of drug discovery is another key objective since infectious diseases spread exponentially and effectively conducting drug discovery could save lives. Advanced Artificial Intelligence (AI) techniques are promising to solve these problems: (1) Federated Learning (FL) is born to keep data privacy while learning data from distributed clients; (2) graph neural network (GNN) can extract structural properties of molecules whose underlying architecture is the connected atoms; and (3) generative adversarial network (GAN) can generate novel molecules while retaining the properties learned from the training data. In this work, we make the first attempt to build a holistic collaborative and privacy-preserving FL framework, namely FL- DISCO, which integrates GAN and GNN to generate molecular graphs. Experimental results demonstrate the effectiveness of FL- DISCO on: (1) IID data for ESOL and QM9, where FL-DISCO can generate highly novel compounds with high drug-likeliness, uniqueness and LogP scores compared to the baseline; (2) non- IID data for ESOL and QM9, where FL-DISCO generates 100% novel compounds with high validity and LogP scores compared to the baseline. We also demonstrate how different fractions of clients, generator and discriminator architectures affect our evaluation scores.

Manu, Daniel↗

Online Power System Event Detection via Bidirectional Generative Adversarial Networks

Accurate and speedy detection of power system events is critical to enhancing the reliability and resiliency of power systems. Although supervised deep learning algorithms show great promise in identifying power system events, they require a large volume of high-quality event labels for training. This paper develops a bidirectional anomaly generative adversarial network (GAN)-based algorithm to detect power system events using streaming PMU data, which does not rely on a huge amount of event labels. By introducing conditional entropy constraint in the objective function of GAN and graph signal processing-based PMU sorting technique, our proposed algorithm significantly outperforms state-of-the-art event detection algorithms in terms of accuracy. To facilitate the adoption of the proposed algorithm, a prototype online platform is also developed using Apache Hadoop, Kafka, and Spark to enable real-time event detection. Here, the accuracy and computational efficiency of the proposed algorithm are validated using a large-scale real-world PMU dataset from the Eastern Interconnection of the United States.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Inverse Design of Two-Dimensional Airfoils Using Conditional Generative Models and Surrogate Log-Likelihoods

Abstract This paper shows how to use conditional generative models in two-dimensional (2D) airfoil optimization to probabilistically predict good initialization points within the vicinity of the optima given the input boundary conditions, thus warm starting and accelerating further optimization. We accommodate the possibility of multiple optimal designs corresponding to the same input boundary condition and take this inversion ambiguity into account when designing our prediction framework. To this end, we first employ the conditional formulation of our previous work BézierGAN–Conditional BézierGAN (CBGAN)—as a baseline, then introduce its sibling conditional entropic BézierGAN (CEBGAN), which is based on optimal transport regularized with entropy. Compared with CBGAN, CEBGAN overcomes mode collapse plaguing conventional GANs, improves the average lift-drag (Cl/Cd) efficiency of airfoil predictions from 80.8% of the optimal value to 95.8%, and meanwhile accelerates the training process by 30.7%. Furthermore, we investigate the unique ability of CEBGAN to produce a log-likelihood lower bound that may help select generated samples of higher performance (e.g., aerodynamic performance). In addition, we provide insights into the performance differences between these two models with low-dimensional toy problems and visualizations. These results and the probabilistic formulation of this inverse problem justify the extension of our GAN-based inverse design paradigm to other inverse design problems or broader inverse problems.

Engineering↗

Optimization of InGaN quantum well interfaces for fast interwell carrier transport and low nonradiative recombination

Efficient high-power operation of light emitting diodes based on InGaN quantum wells (QWs) requires rapid interwell hole transport and low nonradiative recombination. The transport rate can be increased by replacing GaN barriers with that of InGaN. Introduction of InGaN barriers, however, increases the rate of the nonradiative recombination. In this work, we have attempted to reduce the negative impact of the nonradiative recombination by introducing thin GaN or AlGaN interlayers at the QW/barrier interfaces. The interlayers, indeed, reduce the nonradiative recombination rate and increase the internal quantum efficiency by about 10%. Here, the interlayers do not substantially slow down the interwell hole transport; for 0.5 nm Al 0.10 Ga 0.90 N interlayers the transport rate has even been found to increase. Another positive feature of the interlayers is narrowing of the QW PL linewidth, which is attributed to smoother QW interfaces and reduced fluctuations of the QW width.

carrier transport↗

Demonstration of p-side down green light emitting diodes with high external quantum efficiencies

GaN/(In,Ga)N heterostructure based visible Light Emitting Diodes (LED) have enabled a wide range of solid-state lighting applications through excellent efficiency and power output in the shorter wavelengths (≤ 475nm) of violet/blue emission. However, the efficiency of emitters in the longer wavelength range (≥ 500nm) drops drastically due to the need to include higher Indium-content in the InGaN quantum wells. Large average polarization fields for high Indium-content quantum wells for conventional P-up structure, opposes the depletion field leading to large electrostatic barriers for both electrons and holes injection. LEDs fabricated along the N-polar direction with a p-up orientation or Ga-polar direction with p-down orientation lower such electrostatic barriers to carrier injection due to alignment of the polarization dipole field and depletion region field. This can therefore theoretically improve the electrical injection efficiency and reduce the forward voltage of operation. Such a Ga-polar p-down LED requires a bottom buried tunnel junction to avoid current spreading issues for a buried p-GaN layer. In this report, we demonstrate for the first time Ga-polar p-down green emitting LEDs using bottom tunnel junctions and having external quantum efficiencies comparable to those of equivalent p-up LEDs grown by Metal Organic Chemical Vapor Deposition (MOCVD).

36 MATERIALS SCIENCE↗