Results for “EXPERIMENTATION” — Page 28

DOE OSTI2019

Experimental and numerical investigations of a two-body floating-point absorber wave energy converter in regular waves

This paper presents experimental and numerical studies on the hydrodynamics of a two-body floating-point absorber (FPA) wave energy converter (WEC) under both extreme and operational wave conditions. In this study, the responses of the WEC in heave, surge, and pitch were evaluated for various regular wave conditions. For extreme condition analysis, we assume the FPA system has a survival mode that locks the power-take-off (PTO) mechanism in extreme waves, and the WEC moves as a single body in this scenario. A series of Reynolds-averaged Navier-Stokes (RANS) simulations was performed for the survival condition analysis, and the results were validated with the measurements from experimental wave tank tests. For the FPA system in operational conditions, both a boundary element method (BEM) and the RANS simulations were used to analyze the motion response and power absorption performance. Additional viscous damping, primarily induced by flow separation and vortex shedding, is included in the BEM simulation as a quadratic drag force proportional to the square of body velocity. The inclusion of viscous drag improves the accuracy of BEM's prediction of the heave response and the power absorption performance of the FPA system, which agrees well with experimental data and the RANS simulation results over a broad range of incident wave periods, except near resonance in large wave height scenarios. Overall, the experimental and numerical results suggest that nonlinear effects, caused by viscous damping and interaction between waves and the FPA, significantly influence the system response and power absorption performance. Nonlinear effects were found to be particularly significant when the wave height was large and the period was near or shorter than the resonant period of the FPA system. The study is expected to be helpful for understanding the nonlinear interaction between waves and the FPA system so that the structure of the FPA can be adequately designed.

16 TIDAL AND WAVE POWER↗

DOE OSTI2015

Numerical and experimental studies on effects of moisture content on combustion characteristics of simulated municipal solid wastes in a fixed bed

Highlights: • The effects of moisture content on the burning process of MSW are investigated. • A two-dimensional mathematical model was built to simulate the combustion process. • Temperature distributions, process rates, gas species were measured and simulated. • The The conversion ratio of C/CO and N/NO in MSW are inverse to moisture content. - Abstract: In order to reveal the features of the combustion process in the porous bed of a waste incinerator, a two-dimensional unsteady state model and experimental study were employed to investigate the combustion process in a fixed bed of municipal solid waste (MSW) on the combustion process in a fixed bed reactor. Conservation equations of the waste bed were implemented to describe the incineration process. The gas phase turbulence was modeled using the k–ε turbulent model and the particle phase was modeled using the kinetic theory of granular flow. The rate of moisture evaporation, devolatilization rate, and char burnout was calculated according to the waste property characters. The simulation results were then compared with experimental data for different moisture content of MSW, which shows that the incineration process of waste in the fixed bed is reasonably simulated. The simulation results of solid temperature, gas species and process rate in the bed are accordant with experimental data. Due to the high moisture content of fuel, moisture evaporation consumes a vast amount of heat, and the evaporation takes up most of the combustion time (about 2/3 of the whole combustion process). The whole bed combustion process reduces greatly as MSW moisture content increases. The experimental and simulation results provide direction for design and optimization of the fixed bed of MSW.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2014

New experimental methodology, setup and LabView program for accurate absolute thermoelectric power and electrical resistivity measurements between 25 and 1600 K: Application to pure copper, platinum, tungsten, and nickel at very high temperatures

In this paper we describe an experimental setup designed to measure simultaneously and very accurately the resistivity and the absolute thermoelectric power, also called absolute thermopower or absolute Seebeck coefficient, of solid and liquid conductors/semiconductors over a wide range of temperatures (room temperature to 1600 K in present work). A careful analysis of the existing experimental data allowed us to extend the absolute thermoelectric power scale of platinum to the range 0-1800 K with two new polynomial expressions. The experimental device is controlled by a LabView program. A detailed description of the accurate dynamic measurement methodology is given in this paper. We measure the absolute thermoelectric power and the electrical resistivity and deduce with a good accuracy the thermal conductivity using the relations between the three electronic transport coefficients, going beyond the classical Wiedemann-Franz law. We use this experimental setup and methodology to give new very accurate results for pure copper, platinum, and nickel especially at very high temperatures. But resistivity and absolute thermopower measurement can be more than an objective in itself. Resistivity characterizes the bulk of a material while absolute thermoelectric power characterizes the material at the point where the electrical contact is established with a couple of metallic elements (forming a thermocouple). In a forthcoming paper we will show that the measurement of resistivity and absolute thermoelectric power characterizes advantageously the (change of) phase, probably as well as DSC (if not better), since the change of phases can be easily followed during several hours/days at constant temperature.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

DOE OSTI2016

Hysteresis of liquid adsorption in porous media by coarse-grained Monte Carlo with direct experimental validation

The effects of path-dependent wetting and drying manifest themselves in many types of physical systems, including nanomaterials, biological systems, and porous media such as soil. It is desirable to better understand how these hysteretic macroscopic properties result from a complex interplay between gasses, liquids, and solids at the pore scale. Coarse-Grained Monte Carlo (CGMC) is an appealing approach to model these phenomena in complex pore spaces, including ones determined experimentally. We present two-dimensional CGMC simulations of wetting and drying in two systems with pore spaces determined by sections from micro X-ray computed tomography: a system of randomly distributed spheres and a system of Ottawa sand. Results for the phase distribution, water uptake, and matric suction when corrected for extending to three dimensions show excellent agreement with experimental measurements on the same systems. This supports the hypothesis that CGMC can generate metastable configurations representative of experimental hysteresis and can also be used to predict hysteretic constitutive properties of particular experimental systems, given pore space images.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2016

Theoretical and experimental study on electron interactions with chlorobenzene: Shape resonances and differential cross sections

In this work, we report theoretical and experimental cross sections for elastic scattering of electrons by chlorobenzene (ClB). The theoretical integral and differential cross sections (DCSs) were obtained with the Schwinger multichannel method implemented with pseudopotentials (SMCPP) and the independent atom method with screening corrected additivity rule (IAM-SCAR). The calculations with the SMCPP method were done in the static-exchange (SE) approximation, for energies above 12 eV, and in the static-exchange plus polarization approximation, for energies up to 12 eV. The calculations with the IAM-SCAR method covered energies up to 500 eV. The experimental differential cross sections were obtained in the high resolution electron energy loss spectrometer VG-SEELS 400, in Lisbon, for electron energies from 8.0 eV to 50 eV and angular range from 7{sup ∘} to 110{sup ∘}. From the present theoretical integral cross section (ICS) we discuss the low-energy shape-resonances present in chlorobenzene and compare our computed resonance spectra with available electron transmission spectroscopy data present in the literature. Since there is no other work in the literature reporting differential cross sections for this molecule, we compare our theoretical and experimental DCSs with experimental data available for the parent molecule benzene.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

Preliminary Results on Bayesian Inverse UQ for OECD/NEA WPNCS Subgroup 14 Benchmark Exercise for Error Recovery and Experimental Coverage

The Organization for Economic Cooperation and Development (OECD) Working Party on Nucelar Criticality Safety (WPNCS) has proposed a benchmark exercise representative of neutronic behavior in criticality experiments. Here, the goal is to develop confidence in data assimilation techniques used to adjust nuclear data. Participants are given synthetic experimental models with associated measured data and asked to estimate the model parameters given the model and measurements as well as provide predictions for separate application models. In this work, we performed data assimilation using Bayesian inverse Uncertainty Quantification (UQ) with machine learning surrogate models to produce posterior parameter distributions for the requested parameters and posterior predictive distributions for the requested responses. Several experimental models are shown to insufficiently inform the posterior parameter distributions for the applications involved. However, given sufficient experimental data, posterior parameter estimates yielded reduced uncertainty in the response predictions of interest while covering the experimental data.

Bayesian Inference↗

DOE OSTI2023

Mathematical nuances of Gaussian process-driven autonomous experimentation

Abstract The fields of machine learning (ML) and artificial intelligence (AI) have transformed almost every aspect of science and engineering. The excitement for AI/ML methods is in large part due to their perceived novelty, as compared to traditional methods of statistics, computation, and applied mathematics. But clearly, all methods in ML have their foundations in mathematical theories, such as function approximation, uncertainty quantification, and function optimization. Autonomous experimentation is no exception; it is often formulated as a chain of off-the-shelf tools, organized in a closed loop, without emphasis on the intricacies of each algorithm involved. The uncomfortable truth is that the success of any ML endeavor, and this includes autonomous experimentation, strongly depends on the sophistication of the underlying mathematical methods and software that have to allow for enough flexibility to consider functions that are in agreement with particular physical theories. We have observed that standard off-the-shelf tools, used by many in the applied ML community, often hide the underlying complexities and therefore perform poorly. In this paper, we want to give a perspective on the intricate connections between mathematics and ML, with a focus on Gaussian process-driven autonomous experimentation. Although the Gaussian process is a powerful mathematical concept, it has to be implemented and customized correctly for optimal performance. We present several simple toy problems to explore these nuances and highlight the importance of mathematical and statistical rigor in autonomous experimentation and ML. One key takeaway is that ML is not, as many had hoped, a set of agnostic plug-and-play solvers for everyday scientific problems, but instead needs expertise and mastery to be applied successfully. Graphical abstract

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2020

Uncertainty in Experimental Data Analysis [Slides]

The talk was presented virtually to the Institute of Fundamental Technological Research, Polish Academy of Sciences in Warsaw, Poland, December 21, 2020. Astronomical observations, unusual medical cases, physics experiments too costly to repeat, natural events like earthquakes, hurricanes – all of them are impossible to repeat yet produce important scientific information not achievable in other way. This data should not be treated as qualitative, anecdotal evidence only. It should be analyzed in a mathematically rigorous way to produce quantitative experimental data. Analysis method for one-of-a-kind event data differs from analysis of a repeated experiment data. For a repeated experiments the experimental error includes a range of true values generated by repetitions of the experiment, and measurement uncertainty caused by detectors. They are independent. Repetitions of any experiment, as similar as achievable, always have built-in differences resulting in a range of the true values rather than in a single true experimental value. Measurement uncertainty depends on the measurement system only. Modern digital measurements have very small uncertainty, frequently smaller than the range of true experimental values resulting from built-in differences in the experiment repetitions. When data from one-of-a-kind experiment are analyzed, only the measurement uncertainty can be reported.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2023

Gaussian Process Modeling For Experimental Procedure Uncertainty

Many laboratory experiments generate data that are characterized by a form of uncertainty that differs from noise: experimental procedure uncertainty. The origin of this type of uncertainty is the difficulty in controlling a subset of experimental conditions in such a way that the experiment is perfectly reproducible within noise. In this report, we describe a Gaussian Process modeling-based method that accounts for experimental procedure uncertainty. The method accounts for variations in conditions from experiment to experiment that are independent between experiments, but correlated within each experiment, and incorporates the resulting uncertainty into predictions at future experimental settings. The method is discussed in the context of a specific chemistry application in which Raman scattering spectra are measured from three-component mixtures.

42 ENGINEERING↗

DOE OSTI2019

SPRUCE Vegetation Community Survey Data from SPRUCE Experimental Plots, 2014-2020

This dataset provides vegetation survey data collected across vegetation community plots within the 10 chambered treatment plots (6, 19, 11, 20, 4, 13, 8, 16, 10, 17) and 3 unchambered ambient plots (7, 14, 21) from the Spruce and Peatland Responses Under Changing Environments (SPRUCE) experimental site within the Marcell Experimental Forest in northern Minnesota, USA. Collections occurred from 2014-2020 (2014-04-27 to 2020-08-06). The vegetation community plots, three in each experimental plot, were established in 2014 and designated to be undisturbed and reserved for long-term sampling. Vegetation survey data were collected at the peak of each growing season by placing a 1x2 meter rectangular grid over each community plot. The 1x2 meter grid is subset into 50 20x20 cm grid cells. Observations are of the presence of each species in each grid cell for each subplot. That’s a total of 39 subplots across the 13 experimental plots. From 2018 to 2020, shrub stem density was counted and percent shrub cover was estimated in five selected grid cells in each vegetation community plot. Also included are photographs of each community plot taken at the time of data collection for each measurement year. These data provide insight into the responses of plant community composition to warming and increased carbon dioxide. These data were use in analyses in McPartland et al (2018; 2020). This dataset contains three data files in comma-separate values (*.csv) format and seven compressed (*.zip) files containing 877 JPEG (*.jpg) files. Additional metadata are provided: a data dictionary and a file-level metadata file in comma-separate values (.csv) format and a user guide in PDF (*.pdf) format.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2019

SPRUCE Hyperspectral Remote Sensing of Vegetation Communities in SPRUCE Experimental Plots, 2016

This dataset consists of reflectance observations from hyperspectral remote sensing of the vegetation communities from the Spruce and Peatland Responses Under Changing Environments (SPRUCE) experimental site within the Marcell Experimental Forest in northern Minnesota, USA. Observations were collected in SPRUCE experimental study plots located in the S1-Bog. Community vegetation plots in ten chambered treatment plots (6, 19, 11, 20, 4, 13, 8, 16, 10, 17) and 3 unchambered ambient plots (7, 14, 21) were scanned. Spectral data were collected on 22 September 2016 (2016-09-22) under clear sky conditions beginning at 1:00 p.m. local time (Central Standard Time). Although it was past peak growing season, senescence had only just begun at the site, and experimentally warmed plots were still near peak growing conditions. Data collection was performed using a PP Systems UniSpec-DC spectroradiometer that detected incoming and reflected solar radiation in 3–4 nm bandwidths between 310 and 1100 nm. The fiber optic cable on the Unispec was fitted with a field of view (FOV) restrictor that limited the FOV to approximately 15°. The instrument foreoptic was leveled at 1 m above the ground capturing an area of approximately 35 cm in diameter, or 0.1 m2. White reference scans were performed between each treatment. Bands at the beginning and end of the spectrum were eliminated due to noise, resulting in a reported data range of 400-1000 nm. These data can help characterize boreal peatland plant composition and species diversity and their responses to elevated temperatures and carbon dioxide concentrations. These observations were used in analyses in McPartland et al (2019). This dataset contains 4 data files in comma-separate values (*.csv) format. Additional metadata are provided: four data dictionaries and a file-level metadata file in comma-separate values (.csv) format and a user guide in PDF (*.pdf) format.

54 ENVIRONMENTAL SCIENCES↗

NASA NTRS2022

Comparison of Computational Predictions of the Mach 0.80 Transonic Truss-Braced Wing Configuration with Experimental Data

The NASA Langley and Ames Research Centers have teamed together for comparisons of computational predictions of the Boeing Mach 0.80Transonic Truss-Braced Wing (TTBW) configuration with a high-speed experimental dataset. The Mach 0.80 TTBW vehicle is a high wing, high aspect ratio configuration, designed for a high lift-to-drag ratio. System studies have predicted significant fuel burn and emissions benefits with the TTBW technology moving toward meeting NASA Subsonic Transport Systems-Level-Metrics. A 4.5% scale Mach 0.80 design TTBW model was recently tested at the NASA Ames Research Center 11-by 11-Foot Transonic Wind Tunnel(11-Ft TWT),providing a valuable dataset to validate computational tools and investigate best practices as risk reduction efforts continue for the development of the advanced TTBW vehicle. The NASA Computational Fluid Dynamics (CFD) team has computed free-air flow solutions on the Mach 0.80 design flight configuration and two wind tunnel configuration variants using the USM3D and LAVA flow solvers. Accurate modeling of the configuration tested in the wind tunnel environment is critical to validating the CFD tools, thus the team has included the internal cavity region and sting in their modeling of the configuration, similar to that tested in the 11-Ft TWT. Overall, the CFD simulations compared well and show similar trends as the corrected experimental data for lift and drag polars. The CFD predicted lift curve is shifted in angle of attack from what was observed in the experiment. The shift in lift also was seen in the pitching moment comparison plots. CFD solutions were computed at constant CL test point values and showed overall very good agreement when comparing constant spanwise cuts of pressure coefficient data on the wing and strut with experimental data. CFD cavity corrections were also investigated using the 11-Ft TWT cavity correction method, similar to that used to correct the wind tunnel data. Results showed some improvement in pitching moment coefficient predictions, and an increase in drag, shifting the data to the right in drag polars, further from the experimental data at lower lift conditions, good agreement near the design CL, and slight improvement at the higher lift conditions.

Transonic Truss-Braced Wing↗

NASA NTRSDate not supplied

ARCTRON: A Rapid Experimental Proving Ground for TPS Experiments and Arcjet Technology Development

Innovation in high-enthalpy facilities is fundamentally limited by the cost and risk of experimentation. New concepts for plasma control, diagnostics, facility components, and plasma-material interaction often require repeated iterations that are impractical to perform in production arcjets. As a result, promising ideas may remain unexplored or reach operational facilities only after significant development effort. ARCTRON is being developed as a rapid experimental proving ground where new ideas in plasma science, arcjet engineering, diagnostics, and material response can be conceived, tested, and quantitatively evaluated before transition to large-scale facilities. The platform combines radio-frequency (RF) and DC arc plasma generation, externally applied magnetic fields, configurable gas composition, reduced-pressure operation, laser heating, electrical biasing, and modular diagnostic access. These capabilities permit the plasma source, applied forcing, test article, and measurement configuration to be modified independently, allowing individual physical mechanisms to be isolated more readily than in a traditional test environment. One class of investigations addresses fundamental plasma-surface interaction physics. Conventional material tests often expose a specimen simultaneously to convective heating, reactive species, pressure, shear, radiation, and surface-current effects. The resulting material response may be measured accurately, while the contribution of each mechanism remains difficult to identify. ARCTRON is designed to vary these effects selectively. Plasma chemistry can be changed independently through configurable gas mixtures; magnetic fields and electrical biasing can modify charged-particle transport; laser heating can provide a non-plasma thermal input; and pressure, flow, and discharge mode can be varied over a broad operating space. This enables controlled tests of hypotheses involving surface catalycity, reactive-species transport, plasma-assisted oxidation, electromagnetic effects, shear, and the relative contributions of thermal and chemical loading. A second class of investigations enabled by this approach concerns the engineering of high-enthalpy facilities themselves. Arc-heated facilities are limited by electrode erosion, unstable arc attachment, localized heating, and damage to nozzles and other plasma-facing components. ARCTRON provides a lower-cost environment for testing concepts intended to mitigate these limitations. Candidate investigations include the use of applied magnetic fields to alter current paths and reduce plasma interaction with nozzle walls, ExB forcing to introduce controlled plasma rotation, magnetic or geometric approaches for distributing arc attachment, and alternative electrode or discharge configurations intended to reduce erosion and improve stability. Because the platform is reconfigurable, these concepts can be evaluated through repeated design--build--test cycles before they are considered for implementation in operational facilities. The platform also supports the development and validation of diagnostics that may be difficult to introduce initially into a large arcjet. Current and planned measurements include spatially resolved optical emission spectroscopy, electrostatic probes, fast imaging, pyrometry, calorimetry, laser-induced fluorescence, and absorption spectroscopy. These diagnostics are intended not merely to document a nominal operating condition, but to constrain the local plasma state and its relationship to component or material response. The modular facility geometry allows diagnostic concepts to be tested, calibrated, and compared under repeatable conditions before deployment in more demanding environments. ARCTRON is also supported by an integrated software suite. Automated control and data acquisition allow discharge parameters, gas composition, magnetic fields, diagnostic timing, and test configuration to be recorded as part of each experiment (STARDAC - Software for Testing, Analysis, Research Data, and Control). The Backend for Experiment Analysis, Storage, and Traceability (BEAST) is a database that provides the infrastructure needed to associate heterogeneous measurements with facility configuration, specimen identity, calibration state, geometry, and analysis provenance. This backend is particularly important for exploratory campaigns, in which many related configurations may be tested, and the value of an individual experiment depends on its connection to earlier and subsequent iterations. Complementary analysis capabilities, including computer-vision-based transient response measurements (arcjetCV), three-dimensional surface reconstruction (STARSCAN), and model-based Bayesian inference (SHIELD), and tomography data analysis (TOMATO, PuMA) can be incorporated when required by a specific hypothesis without becoming the focus of every campaign. The central objective of ARCTRON is therefore not to maximize heat flux or reproduce a complete flight environment. Its purpose is to reduce the cost and time required to ask consequential questions about plasma behavior, plasma-facing materials, diagnostics, and arcjet technology. By providing a controlled environment for rapid reconfiguration, mechanism isolation, quantitative measurement, and iterative engineering, ARCTRON can help mature concepts that would otherwise remain too speculative or too risky for evaluation in production facilities. The resulting knowledge can then guide the design of material models, focus test objectives in larger arcjets, reduce facility-development risk, and improve the physical basis of high-enthalpy ground testing. This work will present the ARCTRON architecture, operating modes, diagnostic suite, and digital experimental workflow. Initial experimental results from the first integrated operation of the facility will be presented, including flow characterization, power limitations, and deployment of the initial diagnostic suite. Ongoing development efforts aimed at catalycity characterization, magnetic plasma control, and advanced optical diagnostics will also be discussed, illustrating how the platform supports rapid iteration from concept to experiment.

experimental diagnostics↗

NASA NTRSDate not supplied

ARCTRON: A Rapid Experimental Proving Ground for TPS Experiments and Arcjet Technology Development

Innovation in high-enthalpy facilities is fundamentally limited by the cost and risk of experimentation. New concepts for plasma control, diagnostics, facility components, and plasma-material interaction often require repeated iterations that are impractical to perform in production arcjets. As a result, promising ideas may remain unexplored or reach operational facilities only after significant development effort. ARCTRON is being developed as a rapid experimental proving ground where new ideas in plasma science, arcjet engineering, diagnostics, and material response can be conceived, tested, and quantitatively evaluated before transition to large-scale facilities. The platform combines radio-frequency (RF) and DC arc plasma generation, externally applied magnetic fields, configurable gas composition, reduced-pressure operation, laser heating, electrical biasing, and modular diagnostic access. These capabilities permit the plasma source, applied forcing, test article, and measurement configuration to be modified independently, allowing individual physical mechanisms to be isolated more readily than in a traditional test environment. One class of investigations addresses fundamental plasma-surface interaction physics. Conventional material tests often expose a specimen simultaneously to convective heating, reactive species, pressure, shear, radiation, and surface-current effects. The resulting material response may be measured accurately, while the contribution of each mechanism remains difficult to identify. ARCTRON is designed to vary these effects selectively. Plasma chemistry can be changed independently through configurable gas mixtures; magnetic fields and electrical biasing can modify charged-particle transport; laser heating can provide a non-plasma thermal input; and pressure, flow, and discharge mode can be varied over a broad operating space. This enables controlled tests of hypotheses involving surface catalycity, reactive-species transport, plasma-assisted oxidation, electromagnetic effects, shear, and the relative contributions of thermal and chemical loading. A second class of investigations enabled by this approach concerns the engineering of high-enthalpy facilities themselves. Arc-heated facilities are limited by electrode erosion, unstable arc attachment, localized heating, and damage to nozzles and other plasma-facing components. ARCTRON provides a lower-cost environment for testing concepts intended to mitigate these limitations. Candidate investigations include the use of applied magnetic fields to alter current paths and reduce plasma interaction with nozzle walls, ExB forcing to introduce controlled plasma rotation, magnetic or geometric approaches for distributing arc attachment, and alternative electrode or discharge configurations intended to reduce erosion and improve stability. Because the platform is reconfigurable, these concepts can be evaluated through repeated design--build--test cycles before they are considered for implementation in operational facilities. The platform also supports the development and validation of diagnostics that may be difficult to introduce initially into a large arcjet. Current and planned measurements include spatially resolved optical emission spectroscopy, electrostatic probes, fast imaging, pyrometry, calorimetry, laser-induced fluorescence, and absorption spectroscopy. These diagnostics are intended not merely to document a nominal operating condition, but to constrain the local plasma state and its relationship to component or material response. The modular facility geometry allows diagnostic concepts to be tested, calibrated, and compared under repeatable conditions before deployment in more demanding environments. ARCTRON is also supported by an integrated software suite. Automated control and data acquisition allow discharge parameters, gas composition, magnetic fields, diagnostic timing, and test configuration to be recorded as part of each experiment (STARDAC - Software for Testing, Analysis, Research Data, and Control). The Backend for Experiment Analysis, Storage, and Traceability (BEAST) is a database that provides the infrastructure needed to associate heterogeneous measurements with facility configuration, specimen identity, calibration state, geometry, and analysis provenance. This backend is particularly important for exploratory campaigns, in which many related configurations may be tested, and the value of an individual experiment depends on its connection to earlier and subsequent iterations. Complementary analysis capabilities, including computer-vision-based transient response measurements (arcjetCV), three-dimensional surface reconstruction (STARSCAN), and model-based Bayesian inference (SHIELD), and tomography data analysis (TOMATO, PuMA) can be incorporated when required by a specific hypothesis without becoming the focus of every campaign. The central objective of ARCTRON is therefore not to maximize heat flux or reproduce a complete flight environment. Its purpose is to reduce the cost and time required to ask consequential questions about plasma behavior, plasma-facing materials, diagnostics, and arcjet technology. By providing a controlled environment for rapid reconfiguration, mechanism isolation, quantitative measurement, and iterative engineering, ARCTRON can help mature concepts that would otherwise remain too speculative or too risky for evaluation in production facilities. The resulting knowledge can then guide the design of material models, focus test objectives in larger arcjets, reduce facility-development risk, and improve the physical basis of high-enthalpy ground testing. This work will present the ARCTRON architecture, operating modes, diagnostic suite, and digital experimental workflow. Initial experimental results from the first integrated operation of the facility will be presented, including flow characterization, power limitations, and deployment of the initial diagnostic suite. Ongoing development efforts aimed at catalycity characterization, magnetic plasma control, and advanced optical diagnostics will also be discussed, illustrating how the platform supports rapid iteration from concept to experiment.

experimental diagnostics↗

DOE OSTI2026

Simulation and Experimental Validation of an Integrated Heat Pump – Thermal Energy Storage Using a Room-Temperature Phase Change Material

As the dependence on electrical heat pumps (HPs) and intermittent renewables increases, grid strains are expected to grow. This necessitates an energy storage system to reduce the mismatch between energy supply and demand. Thus, a proposed dual-mode commercially available 14.1 kW HP was integrated with a single 22°C phase change material (PCM) thermal storage system (TES) to load-shift both cooling and heating loads. The HP-TES system was manufactured and experimentally tested using a novel test matrix based on AHRI 210/240 psychrometric conditions. Furthermore, transient dual-mode system-level HP-TES models were developed in Modelica and validated using the experimental test conditions. Base HP cooling and heating experimental tests at ambient temperatures of 35°C and −8.3°C show that the modified HP-TES maintained the rated system capacity and performance. The HP-TES discharge provided approximately 30% and 50% reductions in cooling and heating demand, respectively. The transient HP-TES models predicted system capacity and total power input for discharge and recharge operating modes within ±4% mean percentage error, and recharge power input within ±2%, with maximum errors occurring at the equipment startup. During system operation, the sources of model deviations are first-order polynomial fits of the PCM digital scanning calorimetry (DSC) data and unaccounted supercooling in the PCM during solidification. Nonetheless, the model predictions agree with the experimental tests, demonstrating the availability of robust, accurate, and validated transient models that can be used for further validation and the development of system controls.

25 ENERGY STORAGE↗

DOE OSTI2016

An experimental and theoretical study of glycerol oxidation to 1,3-dihydroxyacetone over bimetallic Pt-Bi catalysts

It is important to utilize glycerol, the main by-product of biodiesel, to manufacture value-added chemicals such as 1,3-dihydroxyacetone (DHA). In the present work, the performance of five different catalysts (Pt-Bi/AC, Pt-Bi/ZSM-5, Pt/MCM-41, Pt-Bi/MCM-41, and Pt/Bi-doped-MCM-41) was investigated experimentally, where Pt-Bi/MCM-41 was found to exhibit the highest DHA yield. To better understand the experimental results and to obtain insight into the reaction mechanism, density functional theory (DFT) computations were conducted to provide energy barriers of elementary steps. Both experimental and calculated results show that for high DHA selectivity, Bi should be located in an adatom-like configuration Pt, rather than inside Pt. A favorable pathway and catalytic cycle of DHA formation were proposed based on the DFT results. A cooperative effect, between Pt as the primary component and Bi as a promoter, was identified for DHA formation. Both experimental and theoretical considerations demonstrate that Pt-Bi is efficient to convert glycerol to DHA selectively.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Experimental and theoretical investigations of rotating algae biofilm reactors (RABRs): Areal productivity, nutrient recovery, and energy efficiency

Microalgae biofilms have been demonstrated to recover nutrients from wastewater and serve as biomass feedstock for bioproducts. However, there is a need to develop a platform to quantitatively describe microalgae biofilm production, which can provide guidance and insights for improving biomass areal productivity and nutrient uptake efficiency. Here, this paper proposes a unified experimental and theoretical framework to investigate algae biofilm growth on a rotating algae biofilm reactor (RABR). Experimental laboratory setups are used to conduct controlled experiments on testing environmental and operational factors for RABRs. We propose a differential–integral equation‐based mathematical model for microalgae biofilm cultivation guided by laboratory experimental findings. The predictive mathematical model development is coordinated with laboratory experiments of biofilm areal productivity associated with ammonia and inorganic phosphorus uptake by RABRs. The unified experimental and theoretical tool is used to investigate the effects of RABR rotating velocity, duty cycle (DC), and light intensity on algae biofilm growth, areal productivity, nutrient uptake efficiency, and energy efficiency in wastewater treatment. Our framework indicates that maintaining a reasonable light intensity range improves biomass areal productivity and nutrient uptake efficiency. Our framework also indicates that faster RABR rotation benefits biomass areal productivity. However, maximizing the nutrient uptake efficiency requires a reasonably low RABR rotating speed. Energy efficiency is strongly correlated with RABR rotating speed and DC.

09 BIOMASS FUELS↗

DOE OSTI2014

Molecular interactions between photosystem I and ferredoxin: an integrated energy frustration and experimental model

The stromal domain (PsaC, PsaD, and PsaE) of photosystem I (PSI) reduces transiently bound ferredoxin (Fd) or flavodoxin. Experimental structures exist for all of these protein partners individually, but no experimental structure of the PSI/Fd or PSI/flavodoxin complexes is presently available. Molecular models of Fd docked onto the stromal domain of the cyanobacterial PSI site are constructed here utilizing X-ray and NMR structures of PSI and Fd, respectively. Moreover, predictions of potential protein-protein interaction regions are based on experimental site-directed mutagenesis and cross-linking studies to guide rigid body docking calculations of Fd into PSI, complemented by energy landscape theory to bring together regions of high energetic frustration on each of the interacting proteins. Results identify two regions of high localized frustration on the surface of Fd that contain negatively charged Asp and Glu residues. Our study predicts that these regions interact predominantly with regions of high localized frustration on the PsaC, PsaD, and PsaE chains of PSI, which include several residues predicted by previous experimental studies.

74 ATOMIC AND MOLECULAR PHYSICS↗