Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EUTECTIC ALLOY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

Pulse MIG Welding of 6061-T6/A356-T6 Aluminum Alloy Dissimilar T-joint

Dissimilar T-joints between 4-mm-thick wrought 6061-T6 and cast A356-T6 aluminum alloy plates are made with pulse metal inert gas welding (P-MIG) process, and the weld geometry, microstructure and mechanical properties of the joints are investigated. The average tensile load of the joints is 9488 N at travel speed 12 mm/s and welding current 165 A with 6061 aluminum alloy as web plate and A356 aluminum alloy as flange plate. The weld zone (WZ) is composed of dendrite zone and columnar zone, which is wide at bottom of weld making it become a weak zone. Besides, grain boundary (GB) liquation, consisting of GB eutectic and solute-depleted α-Al, occurs in the partially melted zone on 6061 aluminum alloy side. The T-joint with highest tensile load fails at the root of WZ and the flange plate near the weld with different fracture modes.

36 MATERIALS SCIENCE↗

Formation Mechanism of Nanoscale Al{sub 3}Fe Phase in Al-Fe Alloy During Semisolid Forming Process

The formation mechanism of nanoscale Al{sub 3}Fe phase in Al-1Fe (wt pct) alloy during rheo-extrusion was investigated, and the mechanical property of the prepared alloy was also measured. The results show that the average length of Al{sub 3}Fe phase in Al-1Fe alloy prepared by rheo-extrusion is 300 nm, which is much more refined than the needlelike Al{sub 3}Fe phase in as-cast Al-1Fe alloy (50 μm). In rheo-extrusion, Al{sub 3}Fe phase formed by eutectic reaction is bonelike, but it could be continuously refined by the shear deformation in the wheel groove, in equal channel angular flow, and in expansion extrusion mold. The total equivalent strain of the shear deformation is higher than 4.82. The tensile strength and elongation of Al-1Fe alloy prepared by rheo-extrusion are 135 MPa and 30 pct, respectively. The tensile strength of Al-1Fe alloy prepared by rheo-extrusion is 58.8 pct higher than that of as-cast Al-1Fe alloy, and the elongation is 19 pct higher than that of as-cast Al-1Fe alloy. Compared with as-cast Al-1Fe alloy, the improvements of tensile strength and elongation caused by shear deformation in rheo-extrusion are higher than the reported improvements induced by rare earth modification.

36 MATERIALS SCIENCE↗

Theory-guided design of duplex-phase multi-principal-element alloys

Density-functional theory (DFT) is used to identify phase-equilibria in multi-principal-element and high-entropy alloys (MPEAs/HEAs), including duplex-phase and eutectic microstructures. Here, a combination of composition-dependent formation energy and electronic-structure-based ordering parameters were used to identify a transition from FCC to BCC favoring mixtures, and these predictions experimentally validated in the Al-Co-Cr-Cu-Fe-Ni system. A sharp crossover in lattice structure and dual-phase stability as a function of composition were predicted via DFT and validated experimentally. The impact of solidification kinetics and thermodynamic stability was explored experimentally using a range of techniques, from slow (castings) to rapid (laser remelting), which showed a decoupling of phase fraction from thermal history, i.e., phase fraction was found to be solidification rate-independent, enabling tuning of a multi-modal cell and grain size ranging from nanoscale through macroscale. Strength and ductility tradeoffs for select processing parameters were investigated via uniaxial tension and small-punch testing on specimens manufactured via powder-based additive manufacturing (directed-energy deposition). This work establishes a pathway for design and optimization of next-generation multiphase superalloys via tailoring of structural and chemical ordering in concentrated solid solutions.

36 MATERIALS SCIENCE↗

Correlative characterization of primary particles formed in as-cast Al-Mg alloy containing a high level of Sc

Primary particles formed in as-cast Al-5Mg-0.6Sc alloy and their role in microstructure and mechanical properties of the alloy were investigated using optical microscopy (OM), scanning electron microscopy (SEM), electron back-scatter diffraction (EBSD) and tensile testing. It was found that primary particles due to a close orientation to matrix could serve as the potent heterogeneous nucleation sites for α-Al during solidification and thus impose a remarkable grain refinement effect. Eutectic structure consisted of layer by layer of ‘Al{sub 3}Sc + α-Al + Al{sub 3}Sc + ⋯’ and cellular-dendritic substructure were simultaneously observed at the particles inside, indicating that these particles could be identified as the eutectics rather than individual Al{sub 3}Sc phase. A calculating method, based on EBSD results, was introduced for the spatial distribution of these particles in matrix. The results showed that these eutectic particles randomly distributed in matrix. In addition, the formation of primary eutectic particles significant improved the strength of the Al-Mg alloy in as-cast condition, which is ascribed to the structural evolution from coarse dendrites to prefect fine equiaxed grains. On the other hand, these large-sized particles due to the tendency to act as the microcrack sources could cause a harmful effect in the ductility of Al-Mg-Sc alloy. - Highlights: •Primary particles exhibit an ‘Al{sub 3}Sc + α-Al + Al{sub 3}Sc + ⋯’ multilayer feature with a cellular-dendritic mode of growth. •EBSD analyses the mechanism of grain refinement and the distribution of primary particles in α-Al matrix. •A computational method was presented to calculate the habit planes of primary particles.

36 MATERIALS SCIENCE↗

How Cerium and Lanthanum as Coproducts Promote Stable Rare Earth Production and New Alloys

The largest outputs of rare earth mining are the low-value byproducts cerium and lanthanum, which burden rare earth supply chains because they must be separated from more desirable rare earths used in magnet production. Promoting demand for cerium and lanthanum can potentially diversify the economics of rare earth mining and improve supply chain stability for all rare earth elements. A promising avenue for increasing byproduct rare earth element demand is their use in aluminum alloys; an application for cerium and lanthanum offering multiple benefits to manufacturing such as energy reduction and improved throughput. Experimental materials science and economic implications of Al-rare earth element alloys will be discussed. We show that Al–La/Ce alloys have elevated mechanical strength compared to more traditional aluminum alloys, in some formulations can be used without heat treatment, and possess a highly castable eutectic microstructure. This report presents the use of cerium and lanthanum in aluminum alloys as an example of how supply chain focused approaches to technological development can benefit stakeholders at every step in production.

36 MATERIALS SCIENCE↗

Thermodynamic Modeling and Experimental Study of the Fe-Cr-Zr System

Wide applications of zircaloys, stainless steels and their interactions in nuclear reactors require the knowledge on phase stability and thermodynamic property of the Fe-Cr-Zr system. This knowledge is also important to develop new Zr-contained Fe-Cr ferritic steels. This work aims at developing thermodynamic models for describing phase stability and thermodynamic property of the Fe-Cr-Zr system using the Calphad approach coupled with experimental study. Thermodynamic descriptions of the Fe-Cr and Cr-Zr systems were either directly adopted or slightly modified from literature. The Fe-Zr system has been remodeled to accommodate recent ab-initio calculation of formation enthalpies of various Fe-Zr compounds. Reliable ternary experimental data and thermodynamic models were mainly available in the Zr-rich region. Therefore, selected ternary alloys located in the vicinity of the eutectic valley of (Fe,Cr,Zr) and (Fe,Cr)2Zr laves phase in the Fe-rich region have been experimentally investigated in this study. Microstructure has been examined by using scanning electron microscope, energy-dispersive Xray spectroscopy and X-ray diffraction. These experimental results, along with the literature data were then used to develop thermodynamic models for phases in the Fe-Cr-Zr system. Calculated phase equilibria and thermodynamic properties of the ternary system yield satisfactory agreements with available experimental data, which gives the confidence to use these models as building blocks for developing a Zr, Fe and Cr contained multicomponent thermodynamic database for broader applications in nuclear reactors.

Yang, Ying↗

High operating temperature heat transfer fluids for solar thermal power generation. Final report

This is the final technical report for the DOE MURI project on developing high-operating temperature heat transfer fluids for solar thermal power generation. This project aimed to evaluate liquid metals as a heat-transport fluid and potential energy storage medium for concentrated solar powered (CSP) systems. The project consisted of five phases, starting with fluid selection and screen and ending with potential CSP integration. The initial fluid selection arrived at heavy liquid metals as candidate fluids such as lead bismuth eutectic (LBE) as the prime liquid-alloy candidate to be studied, given the conditions above. Fifty-seven liquid compositions were initially identified with liquidus temperatures lower than 200°C, composed of elements that provide no driving force to the reduction of Cr 2 O 3 or Al 2 O 3 passivation layers in pipe material which is required for corrosion prevention. LBE was identified as the primary candidate fluid after these compositions were compared against computational thermodynamic modeling to screen all of the selected systems that would be compatible with our design objectives. Twenty-eight of these compositions were also investigated with the rapid characterization methods; the accuracies of the liquidus temperature and the specific heats predicted by the computations were better than 3 percent and 9 percent, respectively. We conducted numerus corrosion tests of various Fe-Cr-Al based steels in LBE and its variants at temperate as high as 800°C. It was found that minor additions to the liquid did not provide sufficient corrosion protection to warrant their use in real applications. Furthermore, we investigated the detailed mechanism of corrosion between heavy liquid metal and the pipe material at these very high temperatures. A liquid metal loop was constructed to operate at these high temperatures. The loop construction and operation lead to valuable lessons learned that will be needed for industrial scale loops. Furthermore, we learned that electromagnetic pumps at these extreme temperatures will have to be reengineered and redesigned to be used for CSP applications.

14 SOLAR ENERGY↗

Superalloy eutectic composites with the VI A refractory elements - Cr, Mo and W

The paper discusses the phase equilibria for the ternary systems NiAlCr, NiAlMo, and NiAlW, with emphasis on reactions from the liquid state, although some of the solid state reactions are mentioned. It is shown that eutectics in the Ni-Al-refractory element (Cr, Mo, W) systems offer the potential for high-temperature turbine blade and vane applications. In particular, it is shown that the phase diagrams of these ternary systems can be manipulated to alter the eutectic phases and morphologies by simple quaternary alloying modifications. The resultant combination of chemistry and structure can be controlled to ensure a behavior that is well-matched to hot section component materials requirements.

Jackson, M. R.↗

Duplex accident tolerant coating for nuclear fuel rods

A method is described for forming duplex layers including an interlayer and a corrosion resistant boundary layer on a nuclear fuel rod cladding tube for use in a water cooled nuclear reactor. The method includes forming, by thermal deposition or physical vapor deposition, on the exterior of a substrate, an inner interlayer with Mo, Ta, W or Nb or other particles, and forming, by thermal deposition or physical vapor deposition, on the interlayer, an outer corrosion resistant layer with particles selected from the group consisting of Cr, a Cr alloy, and combinations thereof. The interlayer prevents eutectic formation between the corrosion resistant layer and the substrate.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Sensitivity of Liquation Cracking to Deposition Parameters and Residual Stresses in Laser Deposited IN718 Alloy

The laser deposited IN718 alloys were fabricated with laser cladding system under different conditions to estimate the sensitivity of weld metal liquation cracking. The microstructure and the crack characterization of the laser deposited IN718 alloy were investigated, and the effect of metallurgical factors and residual stress on the crack sensitivity was analyzed. The results showed that the continuous dendritic Laves was precipitated and formed a Lave–austenite interface with ambiguous nanohardness distribution. The weld metal liquation cracking was propagated along the laser scanning direction and the buildup direction in the laser deposited IN718 alloy simultaneously, and the Nb-/Mo-riched fine granular clusters were formed in the crack surface. The precipitation amount of the coarse eutectic phases, presented as dendrite or network, was increased in the laser deposited alloy fabricated with IN718/C-Fe-Cr composite powder and slow cooling rate. The total crack length and the maximum crack length were decreased by increasing cooling rate, and the transverse residual stress was increased with increasing buildup layer number. The crack sensitivity of the laser deposited IN718 alloy was increased by the crack initiation provided by the metallurgical defects and the eutectic phases with low melting temperatures, and then, crack propagated along the continuous phase under the transverse residual stress.

36 MATERIALS SCIENCE↗

Polymer-Stabilized Liquid Metal Nanoparticles as a Scalable Current Collector Engineering Approach Enabling Lithium Metal Anodes

Dendrites and dead lithium formation over prolonged cycling have long been challenges that hinder the safe implementation of metallic Li anodes. In this study, we employ polymer-stabilized liquid metal nanoparticles (LM-P NPs) of eutectic gallium indium (EGaIn) to create uniform Li nucleation sites enabling homogeneous lithium electrodeposition. Block copolymers of poly(ethylene oxide) and poly(acrylic acid) (PEO-b-PAA) were grafted onto the EGaIn surface, forming stabilized, well-dispersed NPs. Using a scalable spray coating approach, LM-P NPs were fabricated on copper current collectors, providing lithiophilic PEO sites and interactive carboxyl groups to guide Li deposition. The Li-EGaIn alloying process greatly reduced the Li + diffusion barrier, enabling fast Li transport through the coating layer, resulting in decreased nucleation overpotential. Therefore, about five times lower Li nucleation overpotential was obtained on the LM-P modified Cu with an optimal composition of the polymers than the bare Cu substrates. DFT computations was used to reveal the binding properties between the LM-P layer and Li. Due to the regulated Li plating/stripping process, as-obtained 30 μm Li anodes paired with LiNi 0.8 Co 0.1 Mn 0.1 O 2 (NCM8 11 ) with a negative/positive electrode capacity (N/P) ratio ~ 10 exhibited stable cycling performance at 0.5C for over 250 cycles, with an average Coulombic efficiency of 99.55%. Ultrathin Li (1 μm) anodes with an N/P ratio ~ 0.6 were also demonstrated in Li|LiFePO 4 cells, which examined the stabilization of Li by LM-P NPs and monitored practical loadings of Li anodes that are close to anode-free systems.

25 ENERGY STORAGE↗

Evolution of carbide precipitates in Hastelloy N joints during welding and post weld heat treatment

Highlights: • The formation and spheroidization of the eutectic-like carbides are found in the Hastelloy N alloy during welding and PWHT. • All precipitates in the joints before and after the PWHT are identified as a M{sub 6}C type carbide with different morphology. • The diffusion of main element of Mo leads to the decrease of lattice parameter of the carbide during the welding and PWHT. - Abstract: The effects of welding and post weld heat treatment (PWHT) on the morphology, composition and lattice parameter of the precipitates in the welding joints of Hastelloy N alloy have been investigated. Joint samples were prepared using a gas tungsten arc welding process with ERNiMo-2 fillers, and then solid-solution treated at 1100 °C for 20 min. After welding, eutectic M{sub 6}C carbides can be observed in the heat affected zones (HAZ) and weld zones (WZ). These eutectic M{sub 6}C carbides become spheroidized during the following PWHT. The concentration of Si decreases during the transformation from the primary ones to eutectic ones, and then increases during the spheroidizing process. The total concentration of Si + Cr in M{sub 6}C carbides remains stable during welding and PWHT. At the same time, the heat leads to the outward diffusion of Mo from the M{sub 6}C carbides, which results in a decrease of the lattice parameter.

36 MATERIALS SCIENCE↗

Use of Friction Stir Processing for Improving Heat-Affected Zone Liquation Cracking Resistance of a Cast Magnesium Alloy AZ91D

In this work, a cast magnesium alloy AZ91D was friction stir processed. Detailed microstructural studies and Gleeble hot ductility tests were conducted on the as-cast and the FSPed samples to comparatively assess their heat-affected zone liquation cracking behavior. The results show that the use of FSP as a pretreatment to fusion welding can strikingly improve the heat-affected zone liquation cracking resistance of alloy AZ91D by reducing the amount and size of the low-melting eutectic β (Mg{sub 17}Al{sub 12}) as well as by refining the matrix grain size.

36 MATERIALS SCIENCE↗

Corrosion evaluation of Al-Cu-Mn-Zr cast alloys in 3.5% NaCl solution

Corrosion behavior of cast Al-Cu-Mn-Zr (ACMZ) and RR350 alloys was compared to a cast 319 alloy in 3.5 wt.% NaCl. After 168 h immersion, ACMZ and RR350 alloys suffered from preferential attack adjacent to intermetallic particles decorated at grain boundaries while the attack in 319 occurred in eutectic Al-Si dendritic boundaries. Electrochemical data allowed semiquantitative comparison of alloy resistance to corrosion initiation, and ACMZ type alloys, including RR350 and three alloys with higher Cu, were considered more resistant than 319 due to the absence of deleterious Si particles. In case of 319, such Si particles presumably drove higher micro-galvanic influence to initiate and sustain Al corrosion. With lower susceptibility to corrosion initiation, ACMZ alloys should exhibit higher or at minimum similar resistance compared to cast 319.

36 MATERIALS SCIENCE↗

Microstructures of ancient and modern cast silver–copper alloys

The microstructures of modern cast Sterling silver and of cast silver objects about 2500 years old have been compared using optical microscopy (OM), scanning electron microscopy (SEM), transmission electron microscopy (TEM), scanning transmission electron microscopy (STEM), energy dispersive X-ray microanalysis (EDX) and electron backscatter diffraction (EBSD). Microstructures of both ancient and modern alloys were typified by silver-rich dendrites with a few pools of eutectic and occasional cuprite particles with an oxidised rim on the outer surface. EBSD showed the dendrites to have a complex internal structure, often involving extensive twinning. There was copious intragranular precipitation within the dendrites, in the form of very fine copper-rich rods which TEM, X-ray diffraction (XRD), SEM and STEM suggest to be of a metastable face-centred-cubic (FCC) phase with a cube–cube orientation relationship to the silver-rich matrix but a higher silver content than the copper-rich β in the eutectic. Samples from ancient objects displayed a wider range of microstructures including a fine scale interpenetration of the adjoining grains not seen in the modern material. Although this study found no unambiguous evidence that this resulted from microstructural change produced over archaeological time, the copper supersaturation remaining after intragranular precipitation suggests that such changes, previously proposed for wrought and annealed material, may indeed occur in ancient silver castings. - Highlights: • Similar twinned structures and oxidised surfaces seen in ancient and modern cast silver • General precipitation of fine Cu-rich rods apparently formed by discontinuous precipitation is characteristic of as-cast silver. • The fine rods are cube-cube related to the matrix in contrast with the eutectic. • The silver-rich phase remains supersaturated with copper. • Possibly age-related grain boundary features seen in ancient cast silver.

36 MATERIALS SCIENCE↗

High resolution cone beam X-ray computed tomography of 3D-microstructures of cast Al-alloys

X-ray computed tomography (XCT) has become a very important method for non-destructive 3D-characterisation of materials. XCT systems with cone beam geometry, micro- or nano-focus tubes and matrix detectors are increasingly used in research and non-destructive testing. Spatial resolutions down to 1 {mu}m can be reached with such XCT-systems for heterogeneities in metals with high absorption contrast. High resolution cone beam XCT is applied to five different Al-alloys: AlMg5Si7, AlCu4Mg1, AlZn6Mg2Cu2, AlZn8Mg2Cu2 and AlSi12Ni1. Up to four different types of inhomogeneities are segmented in one alloy using voxel sizes between (0.4 {mu}m){sup 3} and (2.3 {mu}m){sup 3}. Target metallography and elemental analysis by energy dispersive X-ray analysis are used to identify the inhomogeneities. The possibilities and restrictions of XCT applied to Al-alloys are discussed. AlMg5Si7 XCT-data with a voxel size of (0.4 {mu}m){sup 3} show inhomogeneities with brighter grey-values than the Al-matrix identified as elongated Fe-aluminides, and those with lower grey-values identified as pores and Mg{sub 2}Si-particles with a 'Chinese script-like' structure. Higher-absorbing interdendritic Al-Al{sub 2}Cu-eutectic regions appear brighter than the Al-dendrites in the CT-data of AlCu4Mg1 with (1.1 {mu}m){sup 3}/voxel, whereas pores > 4 {mu}m appear darker than the Al-matrix. The size and the 3D-structure of the {alpha}-Al dendrite arms with a diameter of 50-100 {mu}m are determined in samples from chill cast billets of AlCu4Mg1 and AlZn6Mg2Cu2 alloys. The irregular interdendritic regions containing eutectic segregations with Cu- and Zn-rich phases are > 5 {mu}m wide. Equally absorbing primary equi-axed Al{sub 3}(Sc, Zr) particles > 5 {mu}m are distinguished in the centres of the dendrites by the level of sphericity values. The distribution of Ni- and Fe-aluminides in a squeeze cast AlSi12Ni1-alloy is imaged with (0.4 {mu}m){sup 3}/voxel, but the Si-phase cannot be segmented.

36 MATERIALS SCIENCE↗