Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Dislocation structure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Comparing structure-property evolution for PM-HIP and forged alloy 625 irradiated with neutrons to 1 dpa

The nuclear power industry has growing interest in qualifying powder metallurgy with hot isostatic pressing (PM-HIP) to replace traditional alloy fabrication methods for reactor structural components. But there is little known about the response of PM-HIP alloys to reactor conditions. This study directly compares the response of PM-HIP to forged Ni-base Alloy 625 under neutron irradiation doses ~0.5–1 displacements per atom (dpa) at temperatures ranging ~321–385 °C. Post-irradiation examination involves microstructure characterization, ASTM E8 uniaxial tensile testing, and fractography. Up through 1 dpa, PM-HIP Alloy 625 appears more resistant to irradiation-induced cavity nucleation than its forged counterpart, and consequently experiences significantly less hardening. This observed difference in performance can be explained by the higher initial dislocation density of the forged material, which represents an interstitial-biased sink that leaves a vacancy supersaturation to nucleate cavities. These findings show promise for qualification of PM-HIP Alloy 625 for nuclear applications, although higher dose studies are needed to assess the steady-state irradiated microstructure.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2022

Effect of laser scanning speed on the microstructure, phase transformation and mechanical property of NiTi alloys fabricated by $\mathrm{LPBF}$

This study investigated the effects of laser scanning speed on the microstructure, phase transformation and properties of NiTi alloys fabricated by laser powder bed fusion (LPBF). In this study, the contributions of metallurgical factors under different scanning speeds, such as Ni evaporation, Ni4Ti3 precipitation, dislocations and internal stress, to the transformation temperature and transformation latent heat were clarified through specially designed experiments. Ni evaporation is found to have the most profound effect, followed by precipitation. Increasing scanning speed is found to reduce Ni loss, thus cause less increase in the transformation temperature and transformation heat of the LPBF-NiTi alloys. Increasing scanning speed also increases the microstructure non-uniformity and thus widens the transformation temperature interval. The orientations of residual stress exhibit strong crystallographic stiffness dependence. The LPBF-NiTi alloys with different scanning speeds all exhibited high strains (>13.4%) and excellent shape memory effect. A LPBF-NiTi honeycomb structure exhibited 96% shape recovery rate after a 60% pre-compressive deformation. Besides, there is an optimum scanning speed for minimum porosity and smallest average pore size. However, the pore structure is found to have weak influence on the tensile behaviour of the LPBF-NiTi alloys, possibly due to the high defect tolerance of the martensitic transformation.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Physics-based model of irradiation creep for ferritic materials under fusion energy operation conditions

Irradiation creep is known to be an important process for structural materials in nuclear environments, potentially leading to creep failure at temperatures where thermal creep is generally negligible. While there is a great deal of data for irradiation creep in steels and zirconium alloys in light water reactor conditions, much less is known for first wall materials under fusion energy conditions. Lacking suitable fusion neutron sources for detailed experimentation, modeling, and simulation can help bridge the dose-rate and spectral-effects gap and produce quantifiable expectations for creep deformation of first wall materials under standard fusion conditions. In this paper, we develop a comprehensive model for irradiation creep created from merging a crystal plasticity representation of the dislocation microstructure and a defect evolution simulator that accounts for the entire cluster dimensionality space. Both approaches are linked by way of a climb velocity that captures dislocation-biased defect absorption and a dislocation strengthening term that reflects the accumulation of defect clusters in the system. Here, we carry out our study in Fe under first wall fusion reactor conditions, characterized by a fusion neutron spectrum with average recoil energies of 20 keV and a damage dose rate of ≈3×10 –7 dpa/s at temperatures between 300 and 800 K.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Synchrotron x-Ray Study of Heterostructured Materials: A Review

Heterostructured materials (HSMs) have shown great potential for breaking the strength-ductility tradeoff. HSMs consist of heterogeneous zones that may have different sizes, shapes, compositions, structures, etc. Interactions and competitions among them often lead to unprecedented properties. However, due to the complex structures in a broad range of length scales, it is challenging to unravel deformation physics and strengthening mechanisms underlying extraordinary mechanical properties. Synchrotron x-rays provide powerful techniques and indispensable tools for investigating HSMs at various length scales. Here, we will present in situ high-energy x-ray diffraction and Laue x-ray microdiffraction techniques and their application in studying the HSMs. In this study, the principles of these techniques will be briefly introduced. We will focus on their application in studying stress partitioning and plastic accommodation during tensile deformation, thermo-driven and/or stress-driven phase transformations and various deformation microstructures like geometrically necessary dislocations and local stress/strain distributions, etc., in HSMs. Some important findings will be summarized. Challenging issues remain in studying HSMs and will be discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Pseudoelastic deformation in Mo-based refractory multi-principal element alloys

Phase diagrams supported by density functional theory methods can be crucial for designing high-entropy alloys that are subset of multi-principal-element alloys. We present phase and property analysis of quinary (MoW) x Zr y (TaTi) 1-x-y refractory high-entropy alloys from combined Calculation of Phase Diagram (CALPHAD) and density-functional theory results, supplemented by molecular dynamics simulations. Both CALPHAD and density-functional theory analysis of phase stability indicates a Mo-W-rich region of this quinary has a stable single-phase body-centered-cubic structure. We report first quinary composition from Mo-W-Ta-Ti-Zr family of alloy with pseudo-elastic behavior, i.e., hysteresis in stress-strain. Our analysis shows that only Mo-W-rich compositions of Mo-W-Ta-Ti-Zr, i.e., Mo+W, show reproducible hysteresis in stress-strain responsible for pseudo-elastic behavior. The (MoW) 85 Zr 7.5 (TaTi) 7.5 was down-selected based on temperature-dependent phase diagram analysis and molecular dynamics simulations predicted elastic behavior that reveals twinning-assisted pseudoelastic behavior. While mostly unexplored in body-centered-cubic crystals, twinning is a fundamental deformation mechanism that competes against dislocation slip in crystalline solids. Furthermore, this alloy shows identical cyclic deformation characteristics during uniaxial < 100 > loading, i.e., the pseudoelasticity is isotropic in loading direction. Additionally, a temperature increase from 77 to 1,500 K enhances the elastic strain recovery in load-unload cycles, offering possibly control to tune the pseudoelastic behavior.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Understanding kinetics of defect annihilation in chemoepitaxy-directed self-assembly.

Directed self-assembly (DSA) of block copolymers (BCP) has attracted considerable interest from the semiconductor industry because it can achieve semiconductor-relevant structures with a relatively simple process and low cost. However, the self-assembling structures can become kinetically trapped into defective states, which greatly impedes the implementation of DSA in high-volume manufacturing. Understanding the kinetics of defect annihilation is crucial to optimizing the process and eventually eliminating defects in DSA. Such kinetic experiments, however, are not commonly available in academic laboratories. To address this challenge, we perform a kinetic study of chemoepitaxy DSA in a 300 mm wafer fab, where the complete defectivity information at various annealing conditions can be readily captured. Through extensive statistical analysis, we reveal the statistical model of defect annihilation in DSA for the first time. The annihilation kinetics can be well described by a power law model, indicating that all dislocations can be removed by sufficiently long annealing time. We further develop image analysis algorithms to analyze the distribution of dislocation size and configurations and discover that the distribution stays relatively constant over time. The defect distribution is determined by the role of the guiding stripe, which is found to stabilize the defects. Although this study is based on polystyrene-b-poly(methyl methacrylate) (PS-b-PMMA), we anticipate that these findings can be readily applied to other BCP platforms as well.

block copolymer↗
DOE OSTI2023

Early self-organization of fission gas bubble superlattice formation in neutron-irradiated monolithic U-10Mo fuels

Self-organization of defect superlattices in far-from-equilibrium systems presents a promising way to mitigate swelling concerns in nuclear materials. The gas bubble superlattice (GBS) is a highly ordered, three-dimensional complex defect structure that can retain fission gasses in Uranium-Molybdenum (U-Mo) fuels. Transmission electron microscopy (TEM) investigation of monolithic U-10Mo fuel irradiated to 1.15 × 10 21 fissions/cm 3 and 1.30 × 10 21 fissions/cm 3 revealed that early-stage ordering preferentially occurs at the grain boundaries (GB) and that the critical bubble size for complete ordering is ~3 nm. Once formed at the GB, the GBS extends towards the grain interior; however, the spread in distance from the GB varies likely depending on the type and strength of the GB sink. TEM results also showed a possible correlation between the growth and evolution of the intragranular disordered bubbles and large dislocation networks. The fission product distribution in and outside of the GBS was also investigated confirming the presence of xenon in the GBS, as well as other fission products including cesium, barium, lanthanum, and cerium.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Precipitation Hardening in Ferroelectric Ceramics

Domain wall motion in ferroics, similar to dislocation motion in metals, can be tuned by well-concepted microstructural elements. In demanding high-power applications of piezoelectric materials, the domain wall motion is considered as a lossy hysteretic mechanism that should be restricted. Current applications for so-called hard piezoelectrics are abundant and hinge on the use of an acceptor-doping scheme. However, this mechanism features severe limitations due to enhanced mobility of oxygen vacancies at moderate temperatures. By analogy with metal technology, the authors present here a new solution for electroceramics, where precipitates are utilized to pin domain walls and improve piezoelectric properties. Through a sequence of sintering, nucleation, and precipitate growth, intragranular precipitates leading to a fine domain structure are developed as shown by transmission electron microscopy, piezoresponse force microscopy, and phase-field simulation. This structure impedes the domain wall motion as elucidated by electromechanical characterization. As a result, the mechanical quality factor is increased by ≈50% and the hysteresis in electrostrain is suppressed considerably. This is even achieved with slightly increased piezoelectric coefficient and electromechanical coupling factor. This novel process can be smoothly implemented in industrial production processes and is accessible to simple laboratory experimentation for microstructure optimization and implementation in various ferroelectric systems.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Influence of post deposition annealing on the microstructural evolution and tensile behavior of austenitic stainless-steel alloy 709 made by laser powder bed fusion

Structural materials used in the next generation nuclear reactors or other advanced energy systems are often required to withstand higher operating temperatures for a longer service life. Alloy 709 (A709), a Nb-containing and N-stabilized Fe-25Ni-20Cr austenitic stainless steel, has been recommended for high-temperature reactor constructions due to the better performance over the baseline Type 316H stainless steel. Here, in the current manuscript, for the first time, the microstructure evolution and tensile behavior of an A709 made by laser powder bed fusion (LPBF) is discussed. The as deposited and heat treated LPBF alloys are compared with a reference wrought alloy. Owing to the chemical segregation and a higher number of dislocations, the LPBF materials show a significantly higher density of precipitates formed during high temperature treatments when compared to the wrought samples. This is reflected when looking at the tensile properties, both at room and elevated temperatures, where LPBF samples show higher strengths compared to wrought materials.

36 MATERIALS SCIENCE↗
DOE OSTI2023

The influence of chemical short-range order on the nanoindentation properties of high-entropy alloys prepared via laser powder bed fusion

Chemical short-range order (CSRO) plays an instrumental role in determining the mechanical properties of high-entropy alloys (HEAs). Current methods for controlling CSRO mainly focus on cast HEAs, which can not solve the problem of grain coarsening caused by homogenization treatments. Laser Powder Bed Fusion (LPBF), which has extremely high cooling rates, can suppress compositional segregation, refine grain structures, and achieve low CSRO. This offers a promising avenue for quantitatively controlling CSRO without the need for homogenization treatments. In this study, we investigate the CSRO of HEAs fabricated via LPBF and elucidate their influence on nanoindentation behavior. The results show that, at the low cooling rate, the average size of CSRO is 0.66 nm and they occupy 2.8% of the cross-sectional area, while at high cooling rate, the corresponding values are 0.92 nm and 9.9%, respectively, both of which are significantly smaller than those of cast HEAs. Furthermore, by analyzing samples with different CSROs, we observe that the hardness increases and then decreases with the increase of CSRO, primarily due to the preferential formation of dislocations in regions enriched with Cr-Mn-Ni. With the improvement of CSRO, both the size and quantity of Cr-Mn-Ni rich region gradually increased; subsequently, as multiple Cr-Mn-Ni rich regions tend to merge into one during the CSRO improvement, the size of the Cr-Mn-Ni rich region continued to increase while the quantity gradually decreased; when the size of the Cr-Mn-Ni rich region is moderate and widely dispersed, the dislocation density is higher with much more uniform distributions, which favorably improves nanoindentation hardness.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Scanning tunneling microscopy study of the antiferromagnetic topological insulator MnBi 2 Se 4

Topological insulators with intrinsic magnetic ordering such as MnBi 2 Se 4 have been predicted to host many exotic topological phenomena including dissipationless edge states and magnetoelectric effects. Here we use scanning tunneling microscopy to study the surface of MnBi 2 Se 4 epitaxial thin films. Large scale topographic images show steps between van der Waals layers and screw dislocations. While we find the Se-termination predominant on the surface, areas attributed to Bi-termination are found at the edges of small islands in as-grown films, or in larger areas upon removal of surface capping. Here, we compare these terminations through an analysis of step heights, atomic resolution images and tunneling spectroscopy. Tunneling spectra on the Se-termination reveals semiconducting behavior, with an apparent bandgap of >0.18eV that depends on the tip height. In contrast, tunneling spectra of the Bi-termination appears gapless, which could be an indication of dangling bond states on the surface. In both cases, a hexagonal 3.9Å lattice is observed that is consistent with the expected crystal structure.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2025

Precise Synthesis of 4.75 V-Tolerant LiCoO 2 with Homogeneous Delithiation and Reduced Internal Strain

The rapid advancements in 3C electronic devices necessitate an increase in the charge cutoff voltage of LiCoO 2 to unlock a higher energy density that surpasses the currently available levels. However, the structural devastation and electrochemical decay of LiCoO 2 are significantly exacerbated, particularly at ≥4.5 V, due to the stress concentration caused by more severe lattice expansion and shrinkage, coupled with heterogeneous Li + intercalation/deintercalation reactions. Herein, employing the molten-salt synthesis technique, we propose a universal morphology-shaping strategy to attain bulk reaction homogeneity and reduce internal strains, even at extremely high charge voltages. The newly designed flattened polygon prismlike LiCoO 2 (P-LCO) particle, featuring a regular symmetrical arrangement along the c-axis, demonstrates a more homogeneous Li + extraction/insertion reaction, which results in a restrained transformation to detrimental O1 phase and reduced variation in lattice volume throughout the (de)lithiation processes. This benefits the mitigation of the local stress accumulation misfit dislocations and particle cracking, ultimately maintaining the mechanical stability of the cathode. Consequently, P-LCO is capable of breaking the voltage ceiling and exhibits exceptional long-term cycling capability at an ultrahigh voltage of 4.75 V. In conclusion, this work offers a brand-new perspective for the rational design of cathode morphology to address capacity deterioration caused by inhomogeneous delithiation and internal strain, thus inspiring the development of high-energy-density cathodes with improved durability.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Tailoring planar slip to achieve pure metal-like ductility in body-centred-cubic multi-principal element alloys

Uniform tensile ductility (UTD) is crucial for the forming/machining capabilities of structural materials. Normally, planar-slip induced narrow deformation bands localize the plastic strains and hence hamper UTD, particularly in body-centred-cubic (bcc) multi-principal element high-entropy alloys (HEAs), which generally exhibit early necking (UTD < 5%). Here we demonstrate a strategy to tailor the planar-slip bands in a Ti-Zr-V-Nb-Al bcc HEA, achieving a 25% UTD together with nearly 50% elongation-to-failure (approaching a ductile elemental metal), while offering gigapascal yield strength. The HEA composition is designed not only to enhance the B2-like local chemical order (LCO), seeding sites to disperse planar slip, but also to generate excess lattice distortion upon deformation-induced LCO destruction, which promotes elastic strains and dislocation debris to cause dynamic hardening. Further, this encourages second-generation planar-slip bands to branch out from first-generation bands, effectively spreading the plastic flow to permeate the sample volume. Moreover, the profuse bands frequently intersect to sustain adequate work-hardening rate (WHR) to large strains. Our strategy showcases the tuning of plastic flow dynamics that turns an otherwise-undesirable deformation mode to our advantage, enabling an unusual synergy of yield strength and UTD for bcc HEAs.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Engineering of Grain Boundaries in CeO 2 Enabling Tailorable Resistive Switching Properties

Abstract Defect engineering in valence change memories aimed at tuning the concentration and transport of oxygen vacancies are studied extensively, however mostly focusing on contribution from individual extended defects such as single dislocations and grain boundaries. In this work, the impact of engineering large numbers of grain boundaries on resistive switching mechanisms and performances is investigated. Three different grain morphologies, that is, “random network,” “columnar scaffold,” and “island‐like,” are realized in CeO 2 thin films. The devices with the three grain morphologies demonstrate vastly different resistive switching behaviors. The best overall resistive switching performance is shown in the devices with “columnar scaffold” morphology, where the vertical grain boundaries extending through the film facilitate the generation of oxygen vacancies as well as their migration under external bias. The observation of both interfacial and filamentary switching modes only in the devices with a “columnar scaffold” morphology further confirms the contribution from grain boundaries. In contrast, the “random network” or “island‐like” structures result in excessive or insufficient oxygen vacancy concentration migration paths. The research provides design guidelines for grain boundary engineering of oxide‐based resistive switching materials to tune the resistive switching performances for memory and neuromorphic computing applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Impact of Irradiation on Microstructure and Mechanical Properties of Materials Produced by Advanced Manufacturing

Advanced non-light water reactor designs, known as Generation IV (Gen IV) reactors, typically operate at higher temperatures and under more extreme radiation conditions than conventional light water reactors. A critical aspect of the successful deployment and advancement of Gen IV reactor designs is the selection of appropriate structural materials for specific applications, which necessitates the timely development of new materials and manufacturing processes. Advanced manufacturing (AM) offers numerous opportunities for innovative designs, enabling the production of high-performance components with potentially shorter development cycles compared to traditional manufacturing methods. However, a significant challenge in deploying AM technologies in the nuclear energy sector is the current lack of data on the irradiation performance of AM-produced components. This presentation will discuss neutron and ion irradiation results of AM materials, including stainless steel 316L, Grade 91, SA508, Inconel 718, and Inconel 625 materials. The materials were manufactured by AM, such as Powder Metallurgy Hot Isostatic Pressing (PM HIP), Laser Powder Bed Fusion (LPBF) and Directed Energy Deposition (DED). The effects of neutron irradiation on microstructure (e.g., dislocations, loops, and nanoclusters), tensile properties (e.g., strength and ductility), and ion irradiation on Irradiation-Assisted Stress Corrosion Cracking (IASCC) will be explored. Results are collected from several projects supported by the Nuclear Science User Facilities (NSUF) program.

36 - MATERIALS SCIENCE↗
DOE OSTI2024

Strength-ductility synergy through microstructural and compositional heterogeneity in directed energy deposition additive manufacturing of face-centered cubic materials

Directed energy deposition (DED) is an additive manufacturing (AM) process based on welding technology and offers the advantages of large build volume, high deposition rate, and ability to fabricate multi-material parts. Epitaxial continuous columnar grain growth is a characteristic microstructural feature of DED processed alloys. In this study, a bamboo-like microstructure (periodic alternation of equiaxed and columnar structure) was produced by adopting an intermittent deposition strategy in 316L stainless steel and Inconel 625. The formation of a bamboo-like alternating microstructure was confirmed through electron backscattered diffraction (EBSD) analysis. Hardness mapping showed that the columnar to equiaxed transition (CET) occurred at the region right below the fusion line. A finite element (FE) model was used to investigate the relationship between the temperature gradient (G) and the solidification rate (R). The FE model showed a low G/R ratio at the region right below the interface promoting the CET. The grain size and material-dependent deformation behaviors are analyzed using digital image correlation (DIC). The lower deformation on the fine-grain regions observed in DIC analysis is attributed to a higher strain hardening rate, which is confirmed through dislocation density analysis on a tensile-interrupted specimen. The periodically alternating grain size coupled with the microstructural changes caused by intermittent deposition strategy result in a better strength-ductility synergy in both single-material and bimetallic specimens.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Interface microstructure effects on dynamic failure behavior of layered Cu/Ta microstructures

Abstract Structural metallic materials with interfaces of immiscible materials provide opportunities to design and tailor the microstructures for desired mechanical behavior. Metallic microstructures with plasticity contributors of the FCC and BCC phases show significant promise for damage-tolerant applications due to their enhanced strengths and thermal stability. A fundamental understanding of the dynamic failure behavior is needed to design and tailor these microstructures with desired mechanical responses under extreme environments. This study uses molecular dynamics (MD) simulations to characterize plasticity contributors for various interface microstructures and the damage evolution behavior of FCC/BCC laminate microstructures. This study uses six model Cu/Ta interface systems with different orientation relationships that are as- created, and pre-deformed to understand the modifications in the plasticity contributions and the void nucleation/evolution behavior. The results suggest that pre-existing misfit dislocations and loading orientations (perpendicular to and parallel to the interface) affect the activation of primary and secondary slip systems. The dynamic strengths are observed to correlate with the energy of the interfaces, with the strengths being highest for low-energy interfaces and lowest for high-energy interfaces. However, the presence of pre-deformation of these interface microstructures affects not only the dynamic strength of the microstructures but also the correlation with interface energy.

42 ENGINEERING↗
DOE OSTI2024

Uncovering the three-dimensional structure of upconverting core–shell nanoparticles with multislice electron ptychography

In photon upconverting core–shell nanoparticles, structure strongly dictates performance. Typical imaging in scanning transmission electron microscopy has sufficient resolution to probe the atomic structure of these nanoparticles, but contrast, dose, and projection limitations make conventional methods insufficient for fully characterizing these structures. Phase retrieval techniques provide a promising alternative imaging mode, and, in particular, multislice electron ptychography can recover depth-dependent information. Here, we study beam-sensitive photon upconverting core–shell nanoparticles with a multislice ptychography approach using a low electron dose to avoid damage. Large strain fields arise in these heterostructures due to the mismatch in lattice parameter between the core and the shell. We reconstruct both a nanoparticle that appears defect-free and one that has a large break in the side and map the distribution of strain in 3D by computing distortion fields from high-resolution potential images of each slice. In the defect-free nanoparticle, we observe twisting of the shell, while in the broken nanoparticle, we measure the 3D position of the crack, the core, and dislocations. These results highlight the advantage of multislice electron ptychography to recover 3D information from a single scan, even under strict electron dose requirements from beam-sensitive samples.

74 ATOMIC AND MOLECULAR PHYSICS↗