Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Diode”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

Al0 0.3 Ga 0.7 N PN diode with breakdown voltage >1600 V

Demonstration of Al0 0.3 Ga 0.7 N PN diodes grown with breakdown voltages in excess of 1600 V is reported. The total epilayer thickness is 9.1 μm and was grown by metal-organic vapour-phase epitaxy on 1.3-mm-thick sapphire in order to achieve crack-free structures. A junction termination edge structure was employed to control the lateral electric fields. A current density of 3.5 kA/cm 2 was achieved under DC forward bias and a reverse leakage current <3 nA was measured for voltages <1200 V. The differential on-resistance of 16 mΩ cm 2 is limited by the lateral conductivity of the n-type contact layer required by the front-surface contact geometry of the device. An effective critical electric field of 5.9 MV/cm was determined from the epilayer properties and the reverse current–voltage characteristics. To our knowledge, this is the first aluminium gallium nitride (AlGaN)-based PN diode exhibiting a breakdown voltage in excess of 1 kV. Finally, we note that a Baliga figure of merit (V br 2 /R spec,on ) of 150 MW/cm 2 found is the highest reported for an AlGaN PN diode and illustrates the potential of larger-bandgap AlGaN alloys for high-voltage devices.

36 MATERIALS SCIENCE↗

Interface characteristics of n-n and p-n Ge/SiC heterojunction diodes formed by molecular beam epitaxy deposition

In this article, we report on the physical and electrical nature of Ge/SiC heterojunction layers that have been formed by molecular beam epitaxy (MBE) deposition. Using x-ray diffraction, atomic force microscopy, and helium ion microscopy, we perform a thorough analysis of how MBE growth conditions affect the Ge layers. We observe the layers developing from independent islands at thicknesses of 100 nm to flat surfaces at 300 nm. The crystallinity and surface quality of the layer is shown to be affected by the deposition parameters and, using a high temperature deposition and a light dopant species, the layers produced have large polycrystals and hence a low resistance. The p-type and n-type layers, 300 nm thick are formed into Ge/SiC heterojunction mesa diodes and these are characterized electrically. The polycrystalline diodes display near ideal diode characteristics (n<1.05), low on resistance and good reverse characteristics. Current-voltage (I-V) measurements at varying temperature prove that all the layers have two-dimensional fluctuations in the Schottky barrier height (SBH) due to inhomogeneities at the heterojunction interface. Capacitance-voltage analysis and the SBH size extracted from I-V analysis suggest strongly that interface states are present at the surface causing Fermi-level pinning throughout the bands. A simple model is used to quantify the concentration of interface states at the surface.

36 MATERIALS SCIENCE↗

Improvement of Vertical Diode Properties by N-type Plasma Doping for Low-Power Phase Change Non-Volatile Memory (NVM)

Using PH{sub 3} N-type plasma doing (PLAD), the device characteristics of high performance vertical switch diode for 50 nm phase-change NVM have been studied. Compared to the conventional beam line ion implantation, there are improvements of diode breakdown voltage (B.V.) and isolation B.V., respectively 20% and 41% by N-type PLAD doping due to the higher doping level and shallower profile in N+ region. It also shows excellent off-leakage properties less than 10 pA/cell without decreasing the Ion. From the results of this study, N-type PLAD has been demonstrated to be effective for vertical diode electrical properties as well as for high productivity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Dopant-induced random telegraph signal in nanoscale lateral silicon pn diodes at low temperatures

We studied current-voltage characteristics of nanoscale pn diodes having the junction formed in a laterally patterned ultrathin silicon-on-insulator layer. At temperatures below 30 K, we observed random telegraph signal (RTS) in a range of forward bias. Since RTS is observed only for pn diodes, but not for pin diodes, one dopant among phosphorus donors or boron acceptors facing across the junction is likely responsible for potential changes affecting the current. Based also on potential measurements by low-temperature Kelvin probe force microscope, RTS is ascribed to trapping/detrapping of carriers by/from a single dopant near the farther edge of the depletion region.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Space charge limited conduction in ultrathin PbS quantum dot solid diodes

As a simple and direct characterization of carrier transport in nanocrystal quantum dot (NQD) solids, current-voltage characterization of ultrathin diodes is proposed. We found the space charge limited conduction (SCLC) behavior in ultrathin PbS NQD diodes with active layer thickness half of the full depletion width; and extracted hole concentrations in the order of 10{sup 15} cm{sup −3}, hole mobilities from 10{sup −4} to 10{sup −5} cm{sup 2}/Vs, trap energy depths varying from 140 meV to 200 meV, and volume trap density around 10{sup 17} cm{sup −3} for thin films with NQDs of diameters 3.3 and 3.6 nm, respectively. We further discuss the validity of applying SCLC to the NQD solids based diodes and the implications of the extracted parameters extensively. Proposed characterization method here is a direct measure of carrier transport in solar cell structures which could provide exact directions in NQD solids based solar cell fabrication and modeling.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Switchable zero-index metamaterials by loading positive-intrinsic-negative diodes

We propose switchable zero-index metamaterials (ZIMs) implemented by split ring resonators (SRRs) loaded with positive-intrinsic-negative (PIN) diode switching elements. We demonstrate that ZIMs can be achieved at around 10 GHz when the PIN diode is switched off. When the PIN diode is switched on, however, the designed metamaterials have impedance matching to the free space, which is useful to reduce the reflections at the interface of two media. The switchable ZIMs are suitable for a wide variety of applications like the beam forming and directive radiation. Experimental results validate the switching ability of the proposed ZIMs.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Investigation of the impact of insulator material on the performance of dissimilar electrode metal-insulator-metal diodes

The performance of thin film metal-insulator-metal (MIM) diodes is investigated for a variety of large and small electron affinity insulators using ultrasmooth amorphous metal as the bottom electrode. Nb{sub 2}O{sub 5}, Ta{sub 2}O{sub 5}, ZrO{sub 2}, HfO{sub 2}, Al{sub 2}O{sub 3}, and SiO{sub 2} amorphous insulators are deposited via atomic layer deposition (ALD). Reflection electron energy loss spectroscopy (REELS) is utilized to measure the band-gap energy (E{sub G}) and energy position of intrinsic sub-gap defect states for each insulator. E{sub G} of as-deposited ALD insulators are found to be Nb{sub 2}O{sub 5} = 3.8 eV, Ta{sub 2}O{sub 5} = 4.4 eV, ZrO{sub 2} = 5.4 eV, HfO{sub 2} = 5.6 eV, Al{sub 2}O{sub 3} = 6.4 eV, and SiO{sub 2} = 8.8 eV with uncertainty of ±0.2 eV. Current vs. voltage asymmetry, non-linearity, turn-on voltage, and dominant conduction mechanisms are compared. Al{sub 2}O{sub 3} and SiO{sub 2} are found to operate based on Fowler-Nordheim tunneling. Al{sub 2}O{sub 3} shows the highest asymmetry. ZrO{sub 2}, Nb{sub 2}O{sub 5}, and Ta{sub 2}O{sub 5} based diodes are found to be dominated by Frenkel-Poole emission at large biases and exhibit lower asymmetry. The electrically estimated trap energy levels for defects that dominate Frenkel-Poole conduction are found to be consistent with the energy levels of surface oxygen vacancy defects observed in REELS measurements. For HfO{sub 2}, conduction is found to be a mix of trap assisted tunneling and Frenkel-Poole emission. Insulator selection criteria in regards to MIM diodes applications are discussed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Design of interferometer system for Keda Torus eXperiment using terahertz solid-state diode sources

A solid-state source based terahertz (THz) interferometer diagnostic system has been designed and characterized for the Keda Torus eXperiment (KTX). The THz interferometer utilizes the planar diodes based frequency multiplier (X48) to provide the probing beam at fixed frequency 0.650 THz, and local oscillator is provided by an independent solid-state diode source with tunable frequency (0.650 THz +/− 10 MHz). Both solid-state sources have approximately 1 mW power. The planar-diode mixers optimized for high sensitivity, ∼750 mV/mW, are used in the heterodyne detection system, which permits multichannel interferometer on KTX with a low phase noise. A sensitivity of {sub min} = 4.5 × 10{sup 16} m{sup −2} and a temporal resolution of 0.2 μs have been achieved during the initial bench test.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Semiconductor superlattice diodes for detection of terahertz photons: The role of hybridization of the plasma and polar-optical phonon modes

The current (voltage) responsivity of a superlattice-based diode detector has been studied theoretically in the terahertz frequency band that includes the region of the polar-optical phonon frequencies. Within the framework of an equivalent circuit approach, the electro-dynamical model which allows one to analyze the responsivity taking into account the hybridization of the plasma and polar-optical phonon modes both in the substrate and in the cladding layers of the diode has been suggested. It has been shown that the presence of the plasma and polar-optical phonon modes gives rise to strong features in the frequency dependence of the responsivity, i.e., to the resonance dips and peaks at frequencies of hybridized plasmons and polar-optical phonons. It has been suggested that by judicious engineering of the superlattice-based diodes, it would be possible to enhance substantially their responsivity in the terahertz frequency band.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

High-power narrow-vertical-divergence photonic band crystal laser diodes with optimized epitaxial structure

900 nm longitudinal photonic band crystal (PBC) laser diodes with optimized epitaxial structure are fabricated. With a same calculated fundamental-mode divergence, stronger mode discrimination is achieved by a quasi-periodic index modulation in the PBC waveguide than a periodic one. Experiments show that the introduction of over 5.5 μm-thick PBC waveguide contributes to only 10% increment of the internal loss for the laser diodes. For broad area PBC lasers, output powers of 5.75 W under continuous wave test and over 10 W under quasi-continuous wave test are reported. The vertical divergence angles are 10.5° at full width at half maximum and 21.3° with 95% power content, in conformity with the simulated angles. Such device shows a prospect for high-power narrow-vertical-divergence laser emission from single diode laser and laser bar.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

A nanoscale vacuum-tube diode triggered by few-cycle laser pulses

We propose and demonstrate a nanoscale vacuum-tube diode triggered by few-cycle near-infrared laser pulses. It represents an ultrafast electronic device based on light fields, exploiting near-field optical enhancement at surfaces of two metal nanotips. The sharper of the two tips displays a stronger field-enhancement, resulting in larger photoemission yields at its surface. One laser pulse with a peak intensity of 4.7 × 10{sup 11 }W/cm{sup 2} triggers photoemission of ∼16 electrons from the sharper cathode tip, while emission from the blunter anode tip is suppressed by 19 dB to ∼0.2 electrons per pulse. Thus, the laser-triggered current between two tips exhibit a rectifying behavior, in analogy to classical vacuum-tube diodes. According to the kinetic energy of the emitted electrons and the distance between the tips, the total operation time of this laser-triggered nanoscale diode is estimated to be below 1 ps.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Photoluminescence excitation measurements using pressure-tuned laser diodes

Pressure-tuned laser diodes in external cavity were used as tunable sources for photoluminescence excitation (PLE) spectroscopy. The method was demonstrated in the 720 nm-1070 nm spectral range using a few commercial laser diodes. The samples for PLE measurements were quantum-well structures grown on GaAs and on InP. The method is superior to standard PLE measurements using titanium sapphire laser because it can be extended to any spectral range where anti-reflection coated laser diodes are available.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Injection locking of a high power ultraviolet laser diode for laser cooling of ytterbium atoms

We developed a high-power laser system at a wavelength of 399 nm for laser cooling of ytterbium atoms with ultraviolet laser diodes. The system is composed of an external cavity laser diode providing frequency stabilized output at a power of 40 mW and another laser diode for amplifying the laser power up to 220 mW by injection locking. The systematic method for optimization of our injection locking can also be applied to high power light sources at any other wavelengths. Our system does not depend on complex nonlinear frequency-doubling and can be made compact, which will be useful for providing light sources for laser cooling experiments including transportable optical lattice clocks.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Switchable diode-effect mechanism in ferroelectric BiFeO{sub 3} thin film capacitors

We investigate the mechanism of a switchable diode behavior observed in ferroelectric SrRuO{sub 3}/BiFeO{sub 3} (BFO)/SrRuO{sub 3} capacitors. We experimentally demonstrate that the switchable diode effect observed in the capacitors is induced by the polarization reversal in the BFO film. The conductivity in an Ohmic region in different oxidation states provides direct evidence that electron hole acts as the majority carrier, delivering p-type conduction. Density functional theory (DFT) calculations show that the p-type conduction arises from an unoccupied gap state of Fe{sup 4+} in an FeO{sub 5} pyramid which is derived from Bi vacancy. Our experimental and DFT study leads to the conclusion that the switchable diode effect originates from an asymmetric band bending in the top and bottom depletion layers modulated by ferroelectric polarization and oxygen vacancies.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Bilayer avalanche spin-diode logic

A novel spintronic computing paradigm is proposed and analyzed in which InSb p-n bilayer avalanche spin-diodes are cascaded to efficiently perform complex logic operations. This spin-diode logic family uses control wires to generate magnetic fields that modulate the resistance of the spin-diodes, and currents through these devices control the resistance of cascaded devices. Electromagnetic simulations are performed to demonstrate the cascading mechanism, and guidelines are provided for the development of this innovative computing technology. This cascading scheme permits compact logic circuits with switching speeds determined by electromagnetic wave propagation rather than electron motion, enabling high-performance spintronic computing.

36 MATERIALS SCIENCE↗

A study on the steady-state solutions of a Bursian diode in the presence of transverse magnetic field, when the electrons of the injected beam are turned back partially or totally

The properties of a steady-state planar vacuum diode driven by a cold electron beam have been investigated in the presence of an external transverse magnetic field, employing both the Eulerian and the Lagrangian formalism. With the help of a numerical scheme, the features of the steady-state solutions have been explored in the Eulerian frame, particularly for the case that corresponds to the potential distributions with a virtual cathode. However, exact analytical formulae for the potential and velocity profiles within the inter-electrode region have been derived with the Lagrangian description. In contrast to the previous work [Phys. Plasmas 22, 042110 (2015)], here we have emphasized the situation when electrons are reflected back to the emitter by the magnetic field. Both partial and complete reflection of the electrons due to the magnetic field have been taken into account. Using the emitter electric field as a characteristic parameter, steady-state solutions have been evaluated for specific values of diode length, applied voltage, and magnetic field strength. It has been shown that, due to the inclusion of the magnetic field, a new region of non-unique solutions appears. An external magnetic field seems to have a profound effect in controlling fast electronic switches based on the Bursian diode.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Maximum time-dependent space-charge limited diode currents

Recent papers claim that a one dimensional (1D) diode with a time-varying voltage drop can transmit current densities that exceed the Child-Langmuir (CL) limit on average, apparently contradicting a previous conjecture that there is a hard limit on the average current density across any 1D diode, as t → ∞, that is equal to the CL limit. However, these claims rest on a different definition of the CL limit, namely, a comparison between the time-averaged diode current and the adiabatic average of the expression for the stationary CL limit. If the current were considered as a function of the maximum applied voltage, rather than the average applied voltage, then the original conjecture would not have been refuted.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Ion beam enhancement in magnetically insulated ion diodes for high-intensity pulsed ion beam generation in non-relativistic mode

High-intensity pulsed ion beam (HIPIB) with ion current density above Child-Langmuir limit is achieved by extracting ion beam from anode plasma of ion diodes with suppressing electron flow under magnetic field insulation. It was theoretically estimated that with increasing the magnetic field, a maximal value of ion current density may reach nearly 3 times that of Child-Langmuir limit in a non-relativistic mode and close to 6 times in a highly relativistic mode. In this study, the behavior of ion beam enhancement by magnetic insulation is systematically investigated in three types of magnetically insulated ion diodes (MIDs) with passive anode, taking into account the anode plasma generation process on the anode surface. A maximal enhancement factor higher than 6 over the Child-Langmuir limit can be obtained in the non-relativistic mode with accelerating voltage of 200–300 kV. The MIDs differ in two anode plasma formation mechanisms, i.e., surface flashover of a dielectric coating on the anode and explosive emission of electrons from the anode, as well as in two insulation modes of external-magnetic field and self-magnetic field with either non-closed or closed drift of electrons in the anode-cathode (A-K) gap, respectively. Combined with ion current density measurement, energy density characterization is employed to resolve the spatial distribution of energy density before focusing for exploring the ion beam generation process. Consistent results are obtained on three types of MIDs concerning control of neutralizing electron flows for the space charge of ions where the high ion beam enhancement is determined by effective electron neutralization in the A-K gap, while the HIPIB composition of different ion species downstream from the diode may be considerably affected by the ion beam neutralization during propagation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗