Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

Effects of Mach Number and Reynolds Number on the Maximum Lift Coefficient of a Wing of NACA 230-series Airfoil Sections

Wing was tested with full-span, partial-span, or split flaps deflected 60 Degrees and without flaps. Chordwise pressure-distribution measurements were made for all flap configurations.. Peak values of maximum lift coefficient were obtained at relatively low free-stream Mach numbers and, before critical Mach number was reached, were almost entirely dependent on Reynolds Number. Lift coefficient increased by increasing Mach number or deflecting flaps while critical pressure coefficient was reached at lower free-stream Mach numbers.

LIFT COEFFICIENTS - AIRFOILS - NACA 230↗

Effect of Mach and Reynolds Numbers on Maximum Lift Coefficient

A knowledge of the effects of Mach and Reynolds numbers on the maximum lift coefficient is becoming of greater importance as the speeds and altitudes attainable by modern airplanes continually increase. Since most maximum-lift tests conducted to date have been either at full-scale Reynolds numbers and low Mach numbers or at high Mach numbers and small Reynolds numbers, very little is known about the inter-related effects of these two parameters on the maximum lift coefficient. In order to obtain quantitative information on these effects, flight tests were conducted at Ames Aeronautical Laboratory on six airplanes, three having NACA conventional airfoil sections, two having NACA low-drag sections, and the sixth having a North American Aviation - NACA compromise low-drag section. The results of these tests which cover a range of Mach numbers from 0.15 to 0.72 and of Reynolds numbers from 4,400,000 to 19,500,000 are assembled, together with a considerable quantity of pertinent wind-tunnel data, and analyzed in the present report. From this analysis, general conclusions have been reached indicating the manner in which the maximum lift coefficient is influenced by variations of Mach and Reynolds numbers.

AIRPLANES - BELL P-63A (AMER ) FLIGHT TESTS↗

Influence of Strain-Gage Balance Characteristics on the Precision Error of the Drag Coefficient

Improvements and results of a new method are presented that computes a pre-test estimate of the precision error of the drag coefficient of a wind tunnel model. The error estimate is defined as the part of the drag coefficient's precision error that is primarily associated with the precision error of the angle of attack measurement and physical characteristics of the chosen strain-gage balance. The method indirectly describes the precision error of the angle of attack measurement by using an assumed balance gage output variation of one microV/V. The physical characteristics of the balance, on the other hand, are described by partial derivatives of the axial and normal forces with respect to the strain-gage outputs. These derivatives can directly be obtained from the data reduction matrix of the balance. The precision error estimate itself is calculated by applying a simple explicit equation that uses the model reference area, the dynamic pressure, the angle of attack, the coefficients of the linear terms of the data reduction matrix, and the electrical output variation of one microvolt per volt as input. Precision errors at constant angle of attack may be visualized as contour plots by plotting them, for example, versus the Mach number and the total pressure. Characteristics of NASA's MC60E balance are used in combination with the reference area of a generic wind tunnel model in order to demonstrate that error estimates are independent of both the balance load format and the units chosen for the description of balance loads, model reference area, and the dynamic pressure. Finally, experimental data from a wind tunnel test of the Ames Check Standard Model in the NASA Ames 11-foot Transonic Wind Tunnel illustrates the application of the method to real-world test data.

precision error↗

Development of Continuous-Energy Eigenvalue Sensitivity Coefficient Calculation Methods in the Shift Monte Carlo Code

Three methods for calculating continuous-energy eigenvalue sensitivity coefficients were developed and implemented into the SHIFT Monte Carlo code within the Scale code package. The methods were used for several simple test problems and were evaluated in terms of speed, accuracy, efficiency, and memory requirements. A promising new method for calculating eigenvalue sensitivity coefficients, known as the CLUTCH method, was developed and produced accurate sensitivity coefficients with figures of merit that were several orders of magnitude larger than those from existing methods.

42 ENGINEERING↗

Determining Importance Weighting Functions for Contributon Theory Eigenvalue Sensitivity Coefficient Methodologies

This study introduced three approaches for calculating the importance weighting function for Contributon and CLUTCH eigenvalue sensitivity coefficient calculations, and compared them in terms of accuracy and applicability. The necessary levels of mesh refinement and mesh convergence for obtaining accurate eigenvalue sensitivity coefficients were determined through two parametric studies, and the results of these studies suggest that a sufficiently-accurate mesh for calculating eigenvalue sensitivity coefficients can be obtained for the Contributon and CLUTCH methods with only a small increase in problem runtime.

99 GENERAL AND MISCELLANEOUS↗

Use of SCALE Continuous-Energy Monte Carlo Tools for Eigenvalue Sensitivity Coefficient Calculations

The TSUNAMI code within the SCALE code system makes use of eigenvalue sensitivity coefficients for an extensive number of criticality safety applications, such as quantifying the data-induced uncertainty in the eigenvalue of critical systems, assessing the neutronic similarity between different critical systems, and guiding nuclear data adjustment studies. The need to model geometrically complex systems with improved fidelity and the desire to extend TSUNAMI analysis to advanced applications has motivated the development of a methodology for calculating sensitivity coefficients in continuous-energy (CE) Monte Carlo applications. The CLUTCH and Iterated Fission Probability (IFP) eigenvalue sensitivity methods were recently implemented in the CE KENO framework to generate the capability for TSUNAMI-3D to perform eigenvalue sensitivity calculations in continuous-energy applications. This work explores the improvements in accuracy that can be gained in eigenvalue and eigenvalue sensitivity calculations through the use of the SCALE CE KENO and CE TSUNAMI continuous-energy Monte Carlo tools as compared to multigroup tools. The CE KENO and CE TSUNAMI tools were used to analyze two difficult models of critical benchmarks, and produced eigenvalue and eigenvalue sensitivity coefficient results that showed a marked improvement in accuracy. The CLUTCH sensitivity method in particular excelled in terms of efficiency and computational memory requirements.

97 MATHEMATICS AND COMPUTING↗

Evaluation of the coolant reactivity coefficient influence on the dynamic response of a small LFR system

An assessment of the coolant reactivity feedback influence on a small Lead-cooled Fast Reactor (LFR) dynamics has been made aimed at providing both qualitative and quantitative insights into the system transient behavior depending on the sign of the above mentioned coefficient. The need of such an investigation has been recognized since fast reactors cooled by heavy liquid metals show to be characterized by a strong coupling between primary and secondary systems. In particular, the coolant density and radial expansion coefficients have been attested to play a major role in determining the core response to any perturbed condition on the Steam Generator (SG) side. The European Lead-cooled System (ELSY)-based demonstrator (DEMO) has been assumed as the reference LFR case study. As a first step, a zero-dimensional dynamics model has been developed and implemented in MATLAB/SIMULINK{sup R} environment; then typical transient scenarios have been simulated by incorporating the actual negative lead density reactivity coefficient and its opposite. In all the examined cases results have shown that the reactor behaves in a completely different way when considering a positive coolant feedback instead of the reference one, the system free dynamics resulting moreover considerably slower due to the core and SG mutually conflicting reactions. The outcomes of the present analysis may represent a useful feedback for both the core and the control system designers. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Innovative Fast Reactors: Impact of Fuel Composition on Reactivity Coefficients

A major challenge for future Fast Reactors could be the recycling of minor actinides (MA) in the core fuel, in order to minimize wastes and contribute to meet both the sustainability objective and the reduction of the burden on a geological disposal. Although the most outstanding issues will be found in the development and validation of the appropriate fuels, the presence of MA in the core can potentially deteriorate the core reactivity coefficients. In the present paper we will show however that there is no physical limit to the amount of MA in the core fuel, but that a careful physics analysis can indicate the most appropriate measures to reduce the MA impact on the reactivity coefficients, and in particular, for Na cooled reactors, on the Na void reactivity coefficient.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Bounce- and MLT-averaged diffusion coefficients in a physics-based magnetic field geometry obtained from RAM-SCB for the March 17 2013 storm

Local acceleration via whistler wave and particle interaction plays a significant role in particle dynamics in the radiation belt. In this work we explore gyro-resonant wave-particle interaction and quasi-linear diffusion in different magnetic field configurations related to the March 17 2013 storm. We consider the Earth's magnetic dipole field as a reference and compare the results against non-dipole field configurations corresponding to quiet and stormy conditions. The latter are obtained with the ring current-atmosphere interactions model with a self-consistent magnetic field RAM-SCB, a code that models the Earth's ring current and provides a realistic modeling of the Earth's magnetic field. By applying quasi-linear theory, the bounce- and MLT-averaged electron pitch angle, mixed term, and energy diffusion coefficients are calculated for each magnetic field configuration. For radiation belt (~1 MeV) and ring current (~100 keV) electrons, it is shown that at some MLTs the bounce-averaged diffusion coefficients become rather insensitive to the details of the magnetic field configuration, while at other MLTs storm conditions can expand the range of equatorial pitch angles where gyro-resonant diffusion occurs and significantly enhance the diffusion rates. When MLT average is performed at drift shell L = 4.25 (a good approximation to drift average), the diffusion coefficients become quite independent of the magnetic field configuration for relativistic electrons, while the opposite is true for lower energy electrons. These results suggest that, at least for the March 17 2013 storm and for L ≲ 4.25, the commonly adopted dipole approximation of the Earth's magnetic field can be safely used for radiation belt electrons, while a realistic modeling of the magnetic field configuration is necessary to describe adequately the diffusion rates of ring current electrons.

79 ASTRONOMY AND ASTROPHYSICS↗

High‐Throughput Evaluation of Hardening Coefficients of Eight Alloying Elements in Magnesium

Liquid–solid diffusion couples (LSDCs) are employed to generate a composition gradient in the single‐phase hexagonal closed‐packed (hcp) solid solution with compositions up to the solubility limit of various solutes in Mg. Nanoindentation scanning across the composition gradient in LSDCs allows effective evaluation of composition‐dependent hardness of eight alloying elements (Al, Ca, Ce, Gd, Li, Sn, Y, and Zn) in the hcp Mg phase. The hardening coefficients, an indicator of the potency of solid‐solution hardening, are evaluated from the measured composition‐hardness data and correlated with various materials properties such as atomic radius, shear modulus, and elastic modulus of the solutes. The rank of hardening potency of Al, Gd, Sn, Y, and Zn measured by nanoindentation is in good agreement with that measured by microindentation reported in the literature. The hardening coefficient (potency) from the strongest to the weakest is Ce > Ca > Y ≈ Gd > Zn > Al ≈ Sn > Li in Mg‐based hcp binary solid solutions. The hardening coefficient is found to be closely correlated with the strengthening potency.

36 MATERIALS SCIENCE↗

Declamped Piezoelectric Coefficients in Patterned 70/30 Lead Magnesium Niobate–Lead Titanate Thin Films

Lateral subdivision of blanket piezoelectric thin films increases the functional properties through both increased domain wall mobility and declamping of the intrinsic response. This work presents the local effects of substrate declamping on the piezoelectric coefficient d 33,f of 300 nm thick, rhombohedral, {001}-oriented lead magnesium niobate–lead titanate thin films at the 70/30 composition (70PMN–30PT). Films grown by chemical solution deposition on platinized Si substrates are patterned into strip structures ranging from 0.75 to 9 µm in width. The longitudinal piezoelectric coefficient, d 33,f , is interrogated as a function of position across the patterned structures by three approaches: finite element modeling, piezoresponse force microscopy, and nanoprobe synchrotron X-ray diffraction. It is found that d 33,f increases from the clamped value of 40–50 to ≈160 pm V -1 at the free sidewall under 200 kV cm -1 excitation. The sidewalls partially declamp the piezoelectric response 500–600 nm into the patterned structure, raising the piezoelectric response at the center of features with lateral dimensions less than 1 µm (3:1 width to thickness aspect ratio). The normalized data from all three methods are in excellent agreement, with quantitative differences providing insight to the field dependence of the piezoelectric coefficient and its declamping behavior.

36 MATERIALS SCIENCE↗

MgSiP 2 : An Infrared Nonlinear Optical Crystal with a Large Non‐Resonant Phase‐Matchable Second Harmonic Coefficient and High Laser Damage Threshold

Superior infrared nonlinear optical (NLO) crystals are in urgent demand in the development of lasers and optical technologies for communications and computing. The critical challenge is to find a crystal with large non‐resonant phase‐matchable NLO coefficients and high laser damage threshold (LDTs) simultaneously, which however scale inversely. This work reports such a material, MgSiP 2, that exhibits a large second harmonic generation (SHG) coefficient of d 14 ≈ d 36 = 89 ± 5 pm V −1 at 1550 nm fundamental wavelength, surpassing the commercial NLO crystals AgGaS 2 , AgGaSe 2 , and ZnGeP 2 . First principles theory reveals the polarizability and geometric arrangement of the [SiP 4 ] tetrahedral units as the origin of this large nonlinear response. Remarkably, it also exhibits a high LDT value of 684 GW cm −2 , which is six times larger than ZnGeP 2 and three times larger than CdSiP 2 . It has a wide transparency window of 0.53–10.35 µm, allowing broadband tunability. Further, it is Type I and Type II phase‐matchable with large effective SHG coefficients of d eff,I ≈80.2 pm V −1 and d eff,II ≈73.4 pm V −1 . The outstanding properties of MgSiP 2 make it a highly attractive candidate for optical frequency conversion in the infrared.

36 MATERIALS SCIENCE↗

Association‐based activity coefficient model for electrolyte solutions

Abstract This work presents an association‐based activity coefficient model that explicitly considers the solution nonideality due to associations among ions and solvent species. Built upon the electrolyte nonrandom two‐liquid (eNRTL) model, the model greatly improves the accuracy of eNRTL model for strongly associating electrolyte solutions due to presence of ionic species with high surface charge density. The model successfully correlates mean ionic activity coefficients of 46 aqueous single‐salt systems from 10 cations and 5 anions at 298.15 K up to their solubility limits. With the ion‐specific association parameters identified, the model accurately predicts activity and osmotic coefficients for aqueous mixed‐salt systems at 298.15 K. The temperature dependence of the model results has also been examined at 273–373 K. With superior accuracy over a wide range of concentration and temperature, the model represents a major advancement over eNRTL model and has a great potential to be a next‐generation model for electrolyte solutions.

Lin, Yu‐Jeng↗

Rate Coefficients of C1 and C2 Criegee Intermediate Reactions with Formic and Acetic Acid Near the Collision Limit: Direct Kinetics Measurements and Atmospheric Implications

Rate coefficients are directly determined for the reactions of the Criegee intermediates (CI) CH2OO and CH3CHOO with the two simplest carboxylic acids, formic acid (HCOOH) and acetic acid (CH3COOH), employing two complementary techniques: multiplexed photoionization mass spectrometry and cavity-enhanced broadband ultraviolet absorption spectroscopy. The measured rate coefficients are in excess of 1 1010 cm3 s 1 , several orders of magnitude larger than those suggested from many previous alkene ozonolysis experiments and assumed in atmospheric modeling studies. These results suggest that the reaction with carboxylic acids is a substantially more important loss process for CIs than is presently assumed. Implementing these rate coefficients in global atmospheric models shows that reactions between CI and organic acids make a substantial contribution to removal of these acids in terrestrial equatorial areas and in other regions where high CI concentrations occur such as high northern latitudes, and implies that sources of acids in these areas are larger than previously recognized.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Estimates of Equivalent Heat Conductivity Coefficients of Carbon Nanotubes

We have obtained estimates of equivalent heat conductivity coefficients of nanostructured elements on the basis of the constructed mathematical model of the thermal energy transfer in a single-layer and a multilayer nanotube surrounded by a homogeneous material in the composite matrix. The values of such coefficients permit conditional replacement of nanotubes by solid anisotropic fibers, which makes it possible, in predicting the effective heat conductivity coefficient of a composite modified by carbon nanotubes, to use the known methods developed in detail to fit fibrous composites.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Time-Dependent Diffusion Coefficient of Fe in MgB{sub 2} Superconductors

The iron (Fe) diffusion in superconducting MgB{sub 2} bulk samples has been studied for sintering time durations of 15 min, 30 min, 1 h, 2 h, and 4 h at 900{sup ∘}C. Fe coating bulk polycrstalline superconducting MgB{sub 2} samples for Fe coating were prepared by pelletizing and used in the diffusion experiments with initial sintering at 800{sup ∘}C for 1 h. A thin layer of Fe was coated on MgB{sub 2} pellets by evaporation in vacuum. Effects of Fe diffusion on the structural, electrical, and superconducting properties of MgB{sub 2} have been investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), infrared spectroscopy (IR), energy-dispersive X-ray spectroscopy (EDS), and resistivity measurements. Fe diffused samples have slightly increased critical transition temperatures and have larger lattice parameter c values, in comparison with bare samples. Fe diffusion coefficients were calculated from depth profiles of c parameter and room temperature resistivity values. Depth profiles were obtained by successive removal of thin layers from Fe diffused surfaces of the samples. Our results have shown that the Fe diffusion coefficient decreases with increasing sintering time and resistivity measurements can be utilized for determination of diffusion coefficient.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Measurement of distribution coefficients on TODGA resin and development of a group separation for mixed activation and fission product samples

Batch equilibrium experiments were performed to determine the distribution coefficients for Sc, Ir, and Ta on N,N,N’,N’tetraoctyl-1,5-diglycolamide (TODGA) resin in various acid matrices. Distribution coefficients were determined in hydrochloric acid (Sc, Ir), nitric acid (Sc, Ta), and a mixture of nitric acid and 0.2M hydrofluoric acid (Sc, Ir, Ta). The distribution coefficients determined through these experiments were then utilized to create a group separation method for activation products, fission products, and environmental constituents.

Louie, Christina A.↗

Optical-property coefficient estimation of bulky medium in experiments with a succinctly analytical calculation

Diffuse optical imaging enables to reconstruct distribution of optical properties, absorption and scattering coefficients, in tissue for breast cancer detection based on diffusion equation with the help of the initial guess obtained from measured data. To estimate the initial guess of the optical-property coefficients, an analytical solution of diffusion equation can be used and compared with the measured data. The analytical solution for a homogeneous infinite medium can be obtained in the frequency domain, expressing that the photon intensity and the phase lag relative to the distance between source and detector in a linear relationship. In this study, a succinct calculation using the trigonometric relation is proposed to estimate the optical-property coefficients. A tank-type and a cylinder Lipovenoes phantoms with two concentrations of 1.25% and 2.5% are employed and measured for verification. It is found that the method proposed here shows better results and results in estimation errors of 0–14.81% for μ{sub a} and 20–42% for μ{sub s}′.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗