Results for “CYLINDRICAL CONFIGURATION” — Page 28

NASA NTRS2009

Cryogenic Testing of Different Seam Concepts for Multilayer Insulation Systems

Recent testing in a cylindrical, comparative cryostat at the Cryogenics Test Laboratory has focused on various seam concepts for multilayer insulation systems. Three main types of seams were investigated: straight overlap, fold-over, and roll wrapped. Each blanket was comprised of 40 layer pairs of reflector and spacer materials. The total thickness was approximately 12.5-mm, giving an average layer density of 32 layers per centimeter. The blankets were tested at high vacuum, soft vacuum, and no vacuum using liquid nitrogen to maintain the cold boundary temperature at 77 K. Test results show that all three seam concepts are all close in thermal performance; however the fold-over method provides the lowest heat flux. For the first series of tests, seams were located 120 degrees around the circumference of the cryostat from the previous seam. This technique appears to have lessened the degradation of the blanket due to the seams. In a follow-on test, a 20 layer blanket was tested in a roll wrapped configuration and then cut down the side of the cylinder, taped together, and re-tested. This test result shows the thermal performance impact of having the seams all in one location versus having the seams clocked around the vessel. This experimental investigation indicates that the method of joining the seams in multilayer insulation systems is not as critical as the quality of the installation process.

Johnson, Wesley L.↗

NASA NTRS1996

Computational Simulation of Damage Progression of Composite Thin Shells Subjected to Mechanical Loads

Defect-free and defected composite thin shells with ply orientation (90/0/+/-75) made of graphite/epoxy are simulated for damage progression and fracture due to internal pressure and axial loading. The thin shells have a cylindrical geometry with one end fixed and the other free. The applied load consists of an internal pressure in conjunction with an axial load at the free end, the cure temperature was 177 C (350 F) and the operational temperature was 21 C (70 F). The residual stresses due to the processing are taken into account. Shells with defect and without defects were examined by using CODSTRAN an integrated computer code that couples composite mechanics, finite element and account for all possible failure modes inherent in composites. CODSTRAN traces damage initiation, growth, accumulation, damage propagation and the final fracture of the structure. The results show that damage initiation started with matrix failure while damage/fracture progression occurred due to additional matrix failure and fiber fracture. The burst pressure of the (90/0/+/- 75) defected shell was 0.092% of that of the free defect. Finally the results of the damage progression of the (90/0/+/- 75), defective composite shell was compared with the (90/0/+/- theta, where theta = 45 and 60, layup configurations. It was shown that the examined laminate (90/0/+/- 75) has the least damage tolerant of the two compared defective shells with the (90/0/+/- theta), theta = 45 and 60 laminates.

Gotsis, P. K.↗

NASA NTRSDate not supplied

Developing Procedures to Implement Geometric Imperfections Beyond Right Circular Cylindrical Shells in Finite Element Method Models

Analysis of aerospace structures is frequently conducted using nominal dimensions and frequently assumes ideal conditions in loading, contact, constraints, et cetera. Off-nominal dimensions and nonideal conditions, however, are present in all structures. These are the result of widely ranging causes from coefficient of thermal expansion mismatches, manufacturing tooling anomalies, to assembly procedures that inadvertently alter the structure. Specifically, geometric imperfections can have potentially significant influence on the response of a structural test article observed in an experiment versus the response given by a numerical simulation. The Python Tool for Implementing Geometric Imperfections in Reduced Structures (Py_TIGIRS) was previously presented as a set of Python scripts to calculate and implement as-manufactured geometric midsurface and thickness imperfections into finite element method (FEM) shell models of nominally right circular cylinders. By taking advantage of the simple shape of a right circular cylinder, interpolations of the measured data points were able to be performed along directions that aligned to the cylindrical coordinate system axes of the entire structure. By taking advantage of the shell representation of the real structure as opposed to modeling using a continuum representation, the thickness variation was able to be implemented by shell section definitions instead of having to modify the position of multiple nodes in the thickness direction. Py_TIGIRS is a useful tool that established a procedural example on how to implement geometric imperfections in right circular cylindrical shell structures. Three new procedures, each expanded from concepts established in Py_TIGIRS, are proposed for various test-article designs and are intended to broaden the range of structures that can be modeled with measured geometric imperfections in the structural analysis community. Each test-article design introduces new challenges to successfully implement geometric imperfections into a FEM model. The first test-article design consists of a carbon fiber reinforced polymer square plate with a hat-shaped stiffener co-cured on one side. This test-article design was for a novel seven-point bend test that was also previously presented. Manufacturing and cure-cycle imperfections are observed using digital image correlation (DIC) techniques. As thermal expansion coefficient mismatches between the plate and stiffener materials were anticipated, a thermal analysis study with continuum shell and solid elements was conducted to capture the global shape observed prior to testing. The second test-article design is of a similar hat-stiffened plate configuration, but with a side length ratio near 3:1 with elongation in the stiffener direction. The test article was used to characterize the response to uniaxial compressive loading in the direction of the stiffener. Due to differing manufacturing steps, a thermal analysis like the one developed for the seven-point bend configuration was unable to mimic the observed geometric imperfections. Instead, a strategy based on applying deformations directly to the structure during analysis was developed for continuum shell and solid element representation of a stiffened panel.

Geometric imperfections↗

NASA NTRS2005

System Developed for Bulk Flow Imaging of a Two-Phase Fluid in a Cylindrical Couette

The Microgravity Observation of Bubble Interactions (MOBI) experiment is working to better understand the physics of gas-liquid suspensions. To study such suspensions, researchers generate bubbles in a large cylindrical flow channel. Then, they use various types of instrumentation, including video imaging, to study the bubbly suspension. Scientists will need a camera view of the majority of the gas-liquid suspension inside of the couette in order to gather the information needed from the MOBI experiment. This will provide the scientists with a qualitative picture of the flow that may indicate flow instabilities or imperfect axial mixing inside the couette. These requirements pose a significant challenge because the imaging and lighting system must be confined to a very tight space since the space available on the International Space Station experiment racks is very limited. In addition, because of the large field of view needed and the detail needed to see the gas-liquid suspension behavior in the image, a digital video camera with high resolution (1024 by 1024 pixels) had to be used. Although the high-resolution camera will provide scientists with the image quality they need, it left little space on the experiment rack for the lighting system. Many configurations were considered for the lighting system, including front-lighting and back-lighting, but because of mechanical design limitations with the couette, back-lighting was not an option.

Juergens, Jeffrey R.↗

NASA NTRS2002

Buckling Behavior of Compression-Loaded Composite Cylindrical Shells with Reinforced Cutouts

Results from a numerical study of the response of thin-wall compression-loaded quasi-isotropic laminated composite cylindrical shells with reinforced and unreinforced square cutouts are presented. The effects of cutout reinforcement orthotropy, size, and thickness on the nonlinear response of the shells are described. A high-fidelity nonlinear analysis procedure has been used to predict the nonlinear response of the shells. The analysis procedure includes a nonlinear static analysis that predicts stable response characteristics of the shells and a nonlinear transient analysis that predicts unstable dynamic buckling response characteristics. The results illustrate how a compression-loaded shell with an unreinforced cutout can exhibit a complex nonlinear response. In particular, a local buckling response occurs in the shell near the cutout and is caused by a complex nonlinear coupling between local shell-wall deformations and in-plane destabilizing compression stresses near the cutout. In general, the addition of reinforcement around a cutout in a compression-loaded shell can retard or eliminate the local buckling response near the cutout and increase the buckling load of the shell, as expected. However, results are presented that show how certain reinforcement configurations can actually cause an unexpected increase in the magnitude of local deformations and stresses in the shell and cause a reduction in the buckling load. Specific cases are presented that suggest that the orthotropy, thickness, and size of a cutout reinforcement in a shell can be tailored to achieve improved response characteristics.

Hilburger, Mark W.↗

NASA NTRS1959

Welded Titanium Case for Space-Probe Rocket Motor

Early in 1958, the Jet Propulsion Laboratory of the California Institute of Technology was requested to participate in a lunar-probe mission code-named Juno II which would place a 15-lb Instrumented payload (Pioneer IV) in the vicinity of the moon. The vehicle was to use the same high-speed upper-stage assembly as flown on the successful Jupiter-C configuration; however, the first-stage booster was to be a Jupiter rather than a Redstone. An analysis of the intended flight and payload configuration Indicated that the feasibility of accomplishing the mission was questionable and that additional performance would have to be obtained if the mission was to be feasible. Since the most efficient way of Increasing the performance of a staged vehicle is to increase the performance of the last stage, a study of possible ways of doing this was made.. Because of the time schedule placed on this effort It was decided to reduce the weight of the fourth-stage rocket-motor case by substituting the annealed 6Al--4V titanium alloy for the Type 410 stainless steel. Although this introduced an unfamiliar material, It reduced the changes in design and fabrication techniques. This particular titanium alloy was chosen on the basis of previous tests which proved the suitability of the alloy as a pressure-vessel material when used at an annealed yield strength of about 120, 000 psi. The titanium-case fourth stage of Juno U is shown with the payload and on the missile in Fig. 1; the stainless-steel motor cases used in the Jupiter-C vehicle are shown in Fig. 2. The fourth-stage motor case has a diameter of 6 in., a length of approximately 38 in. center dot and a nominal cylindrical wall thickness of 0.025 in. As shown in Fig. 1, the case serves as the structural support of the payload and is aligned to the upper stage assembly through an alignment ring. The nozzle is threaded into the end of the motor case, and is of the ceramic-coated steel design. Figure 3 shows a comparison of the components used to make the stainless steel and the 6A1--4V titanium alloy cases. The forward dome and aft fitting for the stainless steel assembly were fabricated from a combination of forged, spun and machined parts.. In order to facilitate the fabrication of the titanium alloy motor ) these components were machined from a large-diameter billet.

Brothers, A. J.↗

NASA NTRS2020

Exploratory Experiments to Probe the Effect of Bulk Density and Porosity on The Morphology and Ejecta Kinematics of Impact Craters

The morphometry of relatively small impact craters are influenced by the physical properties of the target. To investigate the control of bulk density and porosity on the crater-formation processing the gravity regime, we conducted a series of impact experiments, varying each these target parameters while holding the other constant. Three different sands were used to construct cohesionless targets: quartz (0.4-0.8 mm), garnet (0.425-1.0 mm), and alumina (0.297-0.71mm), representing a range of intrinsic grain densities from 2.65 to 4.02 g cm-3. High-porosity targets were constructed by carefully pouring the sand into the center of a cylindrical PVC target bucket (inner diameter 26.2 cm, height 12 cm) and allowing it to fill the bucket at the angle of repose before being leveled flat at the top of the bucket. Low-porosity targets were obtained by pluviation of the granular material through a 1 mm sieve that was set directly above the target bucket. With the disparate intrinsic densities of the sand in combination with the variations of the packing technique, we attained differences in the bulk-target density of up to 32%while keeping porosity constant. The impact experiments were conducted with the vertical gun in the Experimental Impact Laboratory at NASA Johnson Space Center; using 3/16” (4.76 mm) diameter aluminum projectiles launched at1.55 ± 0.03 km s-1. The ejecta were observed using the laser-based Ejection Velocity Measurement System, providing data on launch positions and velocities of ejected particles. Submillimeter topographic data of the resulting craters were collected after each experiment with a NextEngine 3D scanner. Regardless of target material or density, all craters exhibited a simple bowl shape, but a trend of increasing depth-diameter ratio with increasing target porosity is observed across the entire experimental suite. Despite these morphometric differences, ejecta launch angles and speeds remain remarkably similar amongst all of the target configurations.

impact cratering↗

NASA NTRS1998

Mixing of Multiple Jets With a Confined Subsonic Crossflow

Results from a recently completed enhanced mixing program are summarized in the two technical papers. These studies were parts of a High Speed Research (HSR)-supported joint Government/industry/university program that involved, in addition to the NASA Lewis Research Center, researchers at United Technologies Research Center, Allison Engine Company, CFD Research Corporation, and the University of California, Irvine. The studies investigated the mixing of jets injected normal to a confined subsonic mainsteam in both rectangular and cylindrical ducts. Experimental and computational studies were performed in both nonreacting and reacting flows. The orifice geometries and flow conditions were selected as typical of the complex three-dimensional flows in the combustion chambers in low-emission gas turbine engines. The principal conclusion from both the experiments and modeling was that the momentum-flux ratio J and orifice spacing S/H were the most significant flow and geometry variables, respectively. Conserved scalar distributions were similar-independent of reaction, orifice diameter H/d, and shape-when the orifice spacing and the square root of the momentum-flux ratio were inversely proportional. Jet penetration was critical, and penetration decreased as either momentum-flux ratio or orifice spacing decreased. We found that planar averages must be considered in context with the distributions. The mass-flow ratios and the orifices investigated were often very large. The jet-to-mainstream mass-flow ratio was varied from significantly less than 1 to greater than 1. The orifice-area to mainstream-cross-sectional-area was varied from approx. 0 to 0.5, and the axial planes of interest were often just downstream of the orifice trailing edge. Three-dimensional flow was a key part of efficient mixing and was observed for all configurations. As an example of the results, the accompanying figure shows the effects of different rates of mass addition on the opposite walls of a rectangular duct.

Holdeman, James D.↗

NASA NTRS2015

Metallography of Battery Resistance Spot Welds

Li-ion cells provide an energy dense solution for systems that require rechargeable electrical power. However, these cells can undergo thermal runaway, the point at which the cell becomes thermally unstable and results in hot gas, flame, electrolyte leakage, and in some cases explosion. The heat and fire associated with this type of event is generally violent and can subsequently cause damage to the surrounding system or present a dangerous risk to the personnel nearby. The space flight environment is especially sensitive to risks particularly when it involves potential for fire within the habitable volume of the International Space Station (ISS). In larger battery packs such as Robonaut 2 (R2), numerous Li-ion cells are placed in parallel-series configurations to obtain the required stack voltage and desired run-time or to meet specific power requirements. This raises a second and less obvious concern for batteries that undergo certification for space flight use: the joining quality at the resistance spot weld of battery cells to component wires/leads and battery tabs, bus bars or other electronic components and assemblies. Resistance spot welds undergo materials evaluation, visual inspection, conductivity (resistivity) testing, destructive peel testing, and metallurgical examination in accordance with applicable NASA Process Specifications. Welded components are cross-sectioned to ensure they are free of cracks or voids open to any exterior surface. Pore and voids contained within the weld zone but not open to an exterior surface, and are not determined to have sharp notch like characteristics, shall be acceptable. Depending on requirements, some battery cells are constructed of aluminum canisters while others are constructed of steel. Process specific weld schedules must be developed and certified for each possible joining combination. The aluminum canisters' positive terminals were particularly difficult to weld due to a bi-metal strip that comes ultrasonically pre-welded by the manufacturer. This was further complicated as the maximum electrode force was limited to low-electrode force to prevent deflection of the aluminum can during welding. Other Li-ion cells are comprised of smaller diameter cylindrical steel canisters which are inherently capable of handling greater force from the electrodes. Allowing higher-electrode forces aids greatly in insuring a consistent resistance network for the weld. Overall lessons learned: developing good jigs is critical to insure the parts and electrodes are planer to one another and the location of the weld sites remains accurate and repeatable; maintaining strict control over materials is critical--materials must be of a specific hardness and chemical composition to insure that a weld schedule is repeatable; accuracy of the die used to stamp the projections is critical and worth the investment; and proper seasoning of the electrodes is critical to producing consistent welds--once the electrodes have been properly seasoned, cleaning/dressing should be avoided until it is absolutely necessary.

Martinez, J. E.↗

NASA NTRS2022

Linear Disturbance Amplification Over Blunted Flat Plates in High-Speed Flows

Modal and nonmodal instability characteristics of cylindrically blunted flat plates with varying leading edge radii are described for Mach 4 and Mach 6 freestream conditions. The selection of leading edge radii and freestream parameters is informed by experimental conditions. The investigation of this 2D problem provides a slow entropy layer swallowing which allows for an isolated development of perturbations seeded upstream within different wall-normal regions of the flow. At both Mach numbers, a decrease in modal instability amplification was seen as the leading edge radius was increased. Nonmodal analysis reveals amplifying perturbations in the boundary layer as well as in the entropy layer. The medium bluntness regime exhibits the strongest amplification of nonmodal disturbances that is nonmonotonic in character. Small amplitude boundary forcing at the plate surface or volumetric forcing at various wall-normal heights was used to account for receptivity effects. While wall forcing effectively induced modal instabilities, only an actuation above the boundary layer captured disturbances that amplify within the entropy layer. The optimal nonmodal theory’s entropy-layer disturbance evolution exhibited outstanding agreement with controlled forcing, including receptivity effects. The evolution of entropy-layer disturbances from the optimal nonmodal theory showed excellent agreement with the results of receptivity to controlled forcing. Therefore, the nonmodal optimal growth analysis may provide a useful as well as efficient technique to identify the complete disturbance spectrum in blunt hypersonic configurations, where both modal and nonmodal disturbances can amplify in the boundary-layer and entropy-layer regions.

Boundary layer transition↗

NASA NTRS2022

Linear Disturbance Amplification Over Blunted Flat Plates in High-Speed Flows

Modal and nonmodal instability characteristics of cylindrically blunted flat plates with varying leading edge radii are described for Mach 4 and Mach 6 freestream conditions. The selection of leading edge radii and freestream parameters is informed by experimental conditions. The investigation of this 2D problem provides a slow entropy layer swallowing which allows for an isolated development of perturbations seeded upstream within different wall-normal regions of the flow. At both Mach numbers, a decrease in modal instability amplification was seen as the leading edge radius was increased. Nonmodal analysis reveals amplifying perturbations in the boundary layer as well as in the entropy layer. The medium bluntness regime exhibits the strongest amplification of nonmodal disturbances that is nonmonotonic in character. Small amplitude boundary forcing at the plate surface or volumetric forcing at various wall-normal heights was used to account for receptivity effects. While wall forcing effectively induced modal instabilities, only an actuation above the boundary layer captured disturbances that amplify within the entropy layer. The optimal nonmodal theory’s entropy-layer disturbance evolution exhibited outstanding agreement with controlled forcing, including receptivity effects. The evolution of entropy-layer disturbances from the optimal nonmodal theory showed excellent agreement with the results of receptivity to controlled forcing. Therefore, the nonmodal optimal growth analysis may provide a useful as well as efficient technique to identify the complete disturbance spectrum in blunt hypersonic configurations, where both modal and nonmodal disturbances can amplify in the boundary-layer and entropy-layer regions.

Boundary layer transition↗

NASA NTRS1966

Storable Propellant Combustion Instability Program at Lewis Research Center

An experimental program at Lewis Research Center investigates acoustical-mode combustion instability in liquid propellant rockets. One phase of this program is concerned with nitrogen tetroxide and a 50-50 fuel blend of hydrazine-UDMH. Effects on combustor stability and performance by variations in injection velocities, impingement angle and distance, amd thrust per element of triplet injectors were studied in a 10.77-inch- diameter cylindrical combustor at chamber pressures of 100 and 300 psia. Nominal thrust levels were 6700 and 20 000 pounds. Stability rating was accomplished by the use of various size RDX explosive charges to generate tangential pressure disturbances. The injection velocity effect correlated by using a ratio V(sub o)/V(sub f). Stability correlation with V(sub o)/V(sub f) resulted in a sharply humped curve with maximum stability at a ratio of 1.2. Performance decreased with increase in V(sub o)/V(sub f) after a maximum at 0.7, which agreed fairly well with the "uniform mixture ratio distribution" criteria of the Jet Propulsion Laboratory. Variation of impingement angle from 38 deg to 120 deg indicated that performance correlated with the absolute velocity ratio V(sub o)/V(sub f), but stability correlation appeared to be best with a velocity ratio using the radial component of the fuel injection velocity V(sub o)/V(sub fr). Impingement distances from 0.5 to 1.0 inch appeared to have only slight effect on stability and performance. Investigation of injector thrust per element for V(sub o)/V(sub fr) ranging from 0.8 to 2.8 yielded convex maxima curves. Acoustic liners were also tested to improve a liner design computer program, to obtain design criteria, and to develop flight-type liners. A marginally stable and spontaneously unstable combustor were used to evaluate linear configurations. All liners were effective in the marginally stable configuration, and only liners with large theoretical absorptivity were successful in the spontaneously unstable combustor.

Tabata, William K.↗

NASA NTRS2021

Boundary Layer Instabilities Over a Cone-Cylinder-Flare Model at Mach 6

Computations are performed to investigate the boundary-layer instabilities over a sharp cone-cylinder-flare model at zero degrees angle of attack. The model geometry and the flow conditions are selected to match the experiments conducted in the Boeing/AFOSR Mach 6 Quiet Tunnel (BAM6QT) at Purdue University. The geometry consists of a nominally sharp 5-degree half-angle cone, followed by a cylindrical segment and then a 10-degree flare. An axisymmetric separation bubble is generated as a result of the laminar shock/boundary-layer interaction in the cylinder-flare region. The comparison of the laminar flow solution and the schlieren images shows a remarkable agreement between the respective locations of both the boundarylayer edge and the reattachment shock. The predicted heat flux distribution is also in agreement with the measured values downstream of the reattachment location. The analysis of convective and global instabilities is performed for flare half angles equal to 8, 10, and 12 degrees and nosetip radii equal to 0.1, 1, and 5 mm. The linear amplification of first and second Mack mode instabilities that begin to amplify in the cone region are computed with a combination of the parabolized stability equations (PSE) and the harmonic linearized Navier-Stokes equations (HLNSE). The predicted frequency spectra of the surface pressure fluctuations associated with both planar and oblique instability waves are compared with the measured spectra at the various locations of the PCB and Kulite sensors. The comparison shows that the computational analysis captures the distinct lobes within the disturbance amplification spectra measured in the experiments, but some differences in amplification characteristics are noted at low frequencies. Overall, the oblique disturbances are found to be more amplified than the planar disturbances. To our knowledge, this represents the first successful comparison between convective instability analysis and measured surface pressure fluctuations for a hypersonic configuration with a separation bubble. Finally, the global instability analysis shows that the laminar flow becomes supercritical for flare half angles larger than 8 degrees. The unstable global mode for the experimental configuration of a 10 degrees flare and a sharp nosetip cone corresponds to a stationary three-dimensional disturbance that is concentrated in the recirculation region and achieves its maximum growth rate for an azimuthal wavenumber of 5.

Boundary layer transition↗

NASA NTRS2022

Boundary Layer Instabilities Over a Cone-Cylinder-Flare Model at Mach 6

Computations are performed to investigate the boundary-layer instabilities over a sharp cone-cylinder-flare model at zero degrees angle of attack. The model geometry and the flow conditions are selected to match the experiments conducted in the Boeing/AFOSR Mach 6 Quiet Tunnel (BAM6QT) at Purdue University. The geometry consists of a nominally sharp 5-degree half-angle cone, followed by a cylindrical segment and then a 10-degree flare. An axisymmetric separation bubble is generated as a result of the laminar shock/boundary-layer interaction in the cylinder-flare region. The comparison of the laminar flow solution and the schlieren images shows a remarkable agreement between the respective locations of both the boundarylayer edge and the reattachment shock. The predicted heat flux distribution is also in agreement with the measured values downstream of the reattachment location. The analysis of convective and global instabilities is performed for flare half angles equal to 8, 10, and 12 degrees and nosetip radii equal to 0.1, 1, and 5 mm. The linear amplification of first and second Mack mode instabilities that begin to amplify in the cone region are computed with a combination of the parabolized stability equations (PSE) and the harmonic linearized Navier-Stokes equations (HLNSE). The predicted frequency spectra of the surface pressure fluctuations associated with both planar and oblique instability waves are compared with the measured spectra at the various locations of the PCB and Kulite sensors. The comparison shows that the computational analysis captures the distinct lobes within the disturbance amplification spectra measured in the experiments, but some differences in amplification characteristics are noted at low frequencies. Overall, the oblique disturbances are found to be more amplified than the planar disturbances. To our knowledge, this represents the first successful comparison between convective instability analysis and measured surface pressure fluctuations for a hypersonic configuration with a separation bubble. Finally, the global instability analysis shows that the laminar flow becomes supercritical for flare half angles larger than 8 degrees. The unstable global mode for the experimental configuration of a 10 degrees flare and a sharp nosetip cone corresponds to a stationary three-dimensional disturbance that is concentrated in the recirculation region and achieves its maximum growth rate for an azimuthal wavenumber of 5.

Hydrodynamic instability↗

NASA NTRSDate not supplied

Hall Magnetohydrodynamic Power Generation and Drag Augmentation Using A Coaxial-Electrode Configuration During Hypersonic Entry

For interplanetary missions, a spacecraft must reduce its relative velocity from orbital speeds of multiple kilometers per second to zero in order to safely land on the surface of a planetary body. During this phase known as planetary reentry, the spacecraft undergoes high speed above Mach 5 up to Mach 30. This hyper-sonic flight regime imposes a strong bow shock in front of the vehicle that imparts extreme aerodynamic and thermal effects. In addition, during portions of this regime, a plasma is formed in the post-shock flow-field around the vehicle due to these high temperatures. Interaction between an applied magnetic field with this electrically conductive fluid, or magnetohydrodynamic (MHD) interaction, can be utilized to convert kinetic energy from the flow into storable electrical energy. Onboard MHD energy generation can benefit the spacecraft by increasing the power of active thermal control components and vehicle control systems during reentry. MHD interaction also exerts a Lorentz body force on the plasma flow that can be manipulated to act as an additional drag force through the vehicle body. MHD drag augmentation can benefit the spacecraft with an additional control mechanism that operates without moving parts. This can be utilized at higher altitudes and subsequently reduce convective heat transfer to the vehicle. MHD interaction with plasma flow suggests that both power generation and drag augmentation can be integrated together in one design. Modern numerical studies have only demonstrated the viability and potential of MHD energy generation and drag modulation separately for implementation into future spacecraft designs [1] [2] [3]. Steeves et. al. presented one possible generator design specifically for reentry vehicles that utilized a modular panel with two embedded electromagnets and two extruding electrodes for air plasma to flow between. Fujino et. al. presented results that indicated increased total drag with a permanent magnet embedded in the blunt body of the Orbital Reentry Experiment (OREX) trajectory. Furthermore, experimental investigations of these two MHD applications have been limited and separate due to the difficult technical nature of experimental de-sign and analysis. For MHD energy generation, there have been two designs which used a cylindrical fore-body with two embedded permanent magnets and two outward facing curved electrodes for tangency to an artificially ionized plasma that flowed along the body length [4] [5]. The first design was studied using an air microwave (MW) ionized supersonic plasma wind tunnel and the second design used radio frequency (RF) ionization of Argon, but both physically demonstrated the feasibility of MHD energy generation in reentry plasma conditions. For MHD drag modulation, one study involved a small-scale cylindrical blunt body embedded with permanent magnets immersed in plasma flow in an arcjet tunnel [6], and another utilized a spherical permanent magnet enclosed with a spherical forebody that was evaluated in a shock expansion tunnel [7]. Both experimental studies provided physical evidence of drag augmentation due to MHD interactions. Therefore, because of the multi-faceted effects of MHD along with both applications having been deemed feasible and beneficial during reentry, this indicates that a coupled power generation and drag modulation design could be achievable. The axi-symmetric nature of blunt bodies for reentry suggests that a spherical set of two ring electrodes near the nose along the body axis. Based on first principles, flow along the walls of the spherical body can then produce MHD interactions between the electrodes. As a result, two currents are generated: a Hall current that produces power and a primary inductive current that augments the drag force. The goal of this work is to provide a simulated design of a coaxial-electrode con-figuration for power generation and drag modulation for experimental testing.

E. Leong↗

NASA NTRS2016

Hybrid Propulsion In-Situ Resource Utilization Test Facility Results for Performance Characterization

Hybrid propulsion presents a promising alternative to conventional systems for in-space propulsion applications using In-Situ Propellant Production (ISPP). A hybrid propulsion test facility has been built at the NASA Jet Propulsion Laboratory (JPL) with the capability of evaluating ISPP oxidizers (gaseous mixtures of O2 and CO2) and modifying fuel type and chamber geometry. This work is the result of a continuing e ort at JPL to characterize the burn characteristics and performance of different propellant combinations and motor configurations in order to re ne and support preliminary designs. Twelve tests using gaseous oxygen and two paraffin based fuels (Black Paraffin and SP1X) from the 2015 campaign are presented. Different reduction techniques are compared in an e ort to determine the uncertainty associated with deriving a regression rate law and evaluating c* efficiency with the collected data.Hybrid motors are mechanically and chemically simple propulsion systems that have the potential forlong-term storability with low gross mass. The oxidizer (such as gaseous O2) can be produced in-situ,signicantly reducing the landed mass. The solid, inert fuel is stored in the combustion chamber in its most dense state, further reducing the total structural mass and volume. Considerable eorts have been focusedon ISPP for Environmental Control and Life Support Systems (ECLSS) and human exploration of Mars.At optimum oxidizer to fuel ratio (O/F), about 70% of the total propellant mass could be produced in-situ.Paran based fuels exhibit a fast regression rate behavior due to the formation of a thin liquid layer on thefuel surface.1 A high burn rate is necessary in order to reach a medium to high thrust range. In order toachieve an O/F ratio close to optimum performance (between 2.1 and 2.7 for the O2/Paran combination),the fuel mass ow needs to be suciently large compared to the oxidizer ow. The slow regression rateof classical hybrid rocket fuels leads to long fuel grain designs or complicated multi-port structures. Singleport, high regression rate fuels have the potential to reduce residual propellant mass and have a grainlength to diameter ratio (L/D) more favorable for packaging. However, hybrid motors remain at a fairly lowTechnology Readiness Level (TRL), and solutions to accurately measure and increase performance are stilllacking, especially for small-scale motors that are constrained to tight packaging.A total of 12 hotres were performed and analyzed in this campaign. All of these tests were conductedat pressures above the critical pressure of paran wax, approximately 6.7 bar (97 psi).2 Three dierentmotor congurations were explored while conserving a single cylindrical port fuel grain. Additionally, sincethrottling is a crucial advantage of hybrid rocket propulsion systems, low oxidizer mass ows (60 - 100 g/s)and uxes (5 - 30 g/cm2/s) were investigated to determine the performance impact in this regime.

Mechentel, F. S.↗