Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CALCINATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

Processing and characteristics of transparent Gd 3 TaO 7 polycrystalline ceramics

Transparent polycrystalline Gd 3 TaO 7 ceramics were successfully developed. A sol-gel process was used to synthesize Gd 3 TaO 7 powder with a uniform composition and an estimated average particle size of 100 nm. Simultaneous thermal gravimetric analysis and differential thermal analysis (TGA/DTA) was used to identify the decomposition sequence as a function of temperature for the as-synthesized sol-gel powders. Crystallization was confirmed by X-ray diffraction (XRD) and a single phase was achieved by calcining at 1000°C. The calcined powders were hot-pressed at 1400°C to achieve >96% theoretical density with closed pore structure followed by a hot isostatic pressing at 1400°C at 207 MPa to achieve a fully dense structure. Microstructural characterization shows a uniform grain size distribution with an average grain size of about 7 μm. In-line transmission measurements revealed high transparency in the red and infrared. Thermal conductivity was measured to be >1.6 W/mK at room temperature, decreasing to ~1.3 W/mK by 500°C. Dielectric properties remain stable with relative permittivity values just above 200 and loss tangents <0.005 up to 350°C.

36 MATERIALS SCIENCE↗

Machinable, high‐conductivity NaSICON through mitigation of humidity effects during solid‐state synthesis

The Na + super ion conductor (NaSICON, Na 1+x Zr 2 Si x P 3-x O 12 ) is a solid electrolyte well-known for fast, selective Na + transport at low temperatures, uniquely enabling sodium-based batteries. Producing high-quality NaSICON from solid-state methods, especially when cost-effective, potentially hygroscopic precursors are used, is not trivial. To understand and eliminate the influence of humidity during processing, a scheme was developed to reproducibly yield a high Na + conductivity (3.75 mS/cm at 25°C, 81.7 mS/cm at 150°C), high density (97%), and machinable NaSICON without the use of binders, sintering aids, or dopants. Controlled humidity studies over 20%–50% RH coupled with thermal, structural, and electrical analysis reveal that calcination temperatures < 1000°C leave NaSICON processing susceptible to water absorption at > 20% RH due to the presence of hygroscopic Na 3 PO 4 and Na 2 CO 3 during shaping, pressing, and sintering. Water absorption results in NaSICON with lower densities, machinability, and Na+ conductivity, due to impaired intergranular Na+ transport. At the other extreme, fully converting precursor to the NaSICON phase at 1230°C before pressing and sintering leads to poor conductivity and density. By calcining at 1000°C, excellent quality NaSICON may be produced under a range of laboratory environments, enabling low-cost production of high-conductivity, machinable NaSICON necessary the ever-growing energy storage market.

NaSICON↗

Sulphate resistance of low‐clinker engineered cementitious composites examined by MicroXRF imaging

Abstract Engineered cementitious composites (ECC) are a class of high‐performing fibre‐reinforced cementitious materials recognised for their increased ductility and durability compared to conventional cement‐based materials, owing to their autogenously controlled tight crack widths, even when subjected to high strains. To reduce ECC's environmental impact, this research examines the use of a low‐clinker binder − limestone‐calcined clay cement (LC3) − as an alternative to portland cement (PC), along with fly ash to further reduce the clinker proportion and the embodied CO 2 of the formulations. In conventional concrete, LC3 hydrates to a denser microstructure resulting from the synergistic reaction between limestone and calcined clay. At the lower water contents typical of ECC and with the presence of fly ash, the influence of the binder composition on the microstructure is difficult to anticipate. To examine the influence of these compositional variables on microstructure, permeability and durability, the sulphate resistance of LC3‐based ECC is explored. Specifically, the ECC‐LC3 blends are designed with high clinker replacement rate of 75% by mass of binder and contain either conventional fly ash or reclaimed fly ash at 50% by mass of binder. Expansion of ECC‐LC3 samples subjected to standard sodium sulphate test conditions was measured up to 12 months and the depth of penetration of sulphates into the ECC‐LC3 of varying compositions was quantified using micro‐X‐Ray Fluorescence (microXRF) imaging and modelling. The expansion results show that the ECC‐LC3 formulations performed better than the PC samples and can provide adequate resistance to external sulphate attack, even when reclaimed fly ashes are used in place of the conventional ash. In addition, the shallow penetration of sulphate into these cementitious composites demonstrates the low diffusion coefficients values that were determined using the quantitative data from MicroXRF imaging.

Microscopy↗

Development of spectroscopic tools for nuclear forensics signatures development

The Savannah River National Laboratory (SRNL) has been developing advanced spectroscopic tools for the characterization of plutonium-bearing compounds with the intent to develop material and process signatures for nuclear forensics. Plutonium in a production, refining, or finishing facility will exist in many forms including oxide precursors (PuF4, PuF3, Pu oxalate, etc.), oxide, and metal. The ability to identify plutonium in each of these chemical forms and determine their processing history is crucial for the development of spectroscopic signatures. This presentation will focus on our work to develop and apply spectroscopic tools at SRNL using doubled-walled cells (DWC) to characterize the thermal decomposition of oxalates, calcination chemistry, alpha-decay-induced chemistry, age dating since last calcination, and other signatures related to plutonium processing.

Villa-Aleman, Eliel↗

The Fe{sup 2+}/Fe{sup 3+} ratio in natural and heat-treated iron-rich eudialytes

The structures of natural iron-rich eudialyte (specimen 3458 from the Khibiny massif, the Kola Peninsula) and two heat-treated samples of this mineral calcined at 700 and 800 Degree-Sign C were determined by X-ray diffraction. The trigonal unit-cell parameters (sp. gr. R3m) are as follows: a = 14.2645(1) Angstrom-Sign , c = 29.9635(5) Angstrom-Sign ; a = 14.1307(1) Angstrom-Sign , c = 30.1229(3) Angstrom-Sign ; a = 14.1921(2) Angstrom-Sign , c = 30.2417(5) Angstrom-Sign , respectively. It was found that Fe{sup 3+} ions in the calcined eudialytes, as well as impurities in the starting specimen, occupy the square-pyramidal Fe{sup 3+}(V) sites, whereas Fe{sup 2+} ions are in the planar-tetragonal Fe{sup 2+}(IV) sites.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Toward Stabilizing Co 3 O 4 Nanoparticles as an Oxygen Reduction Reaction Catalyst for Intermediate-Temperature SOFCs

The oxygen reduction reaction (ORR) activity of a series of composite cathodes consisting of a porous Gd 0.20 Ce 0.80 O 2-δ (GDC) scaffold infiltrated with Sr-, Co-, and Y-nitrate solutions has been systematically investigated in this study. The results show that such infiltrated cathodes if calcined at low temperatures such as 350°C exhibit low polarization resistance (RP) in the temperature range of 450–700°C, even though XRD analysis reveals that the calcined product is virtually a mixture of Co 3 O 4 and SrCO 3 . A further study by design-of-experiment suggests that the true ORR-active species is Co 3 O 4 , whereas SrCO 3 serves as a sintering inhibitor to preserve the high surface area of Co 3 O 4 . The findings and understanding in this study present a new strategy for future development of active cathodes for intermediate-temperature solid oxide fuel cells (SOFCs).

36 MATERIALS SCIENCE↗

Lowering oxygen evolution overpotential via morphology control of NiO x nanocatalysts

NiO x nanocatalysts with two distinct morphologies, nano-spindles and nano-plates, were synthesized and evaluated for oxygen evolution reaction (OER) performance. Spindle-like NiO x was prepared via a hydrothermal reaction of nickel nitrate and urea with cetyltrimethylammonium bromide as a surfactant at 120 °C for 24 h, forming Ni(OH) 2 -based intermediates that were subsequently calcined at 300 °C for 3 h. In contrast, platelet-like Ni(OH) 2 nanocrystals were obtained using nickel(II) acetate and KOH at 180 °C for 24 h, followed by calcination at 400 °C or 500 °C for 4 h to yield NiO x nano-plates. The NiO x nano-spindles exhibited an OER overpotential of 395 mV at 10 mA/cm 2 , whereas the NiO x nano-plates annealed at 400 °C and 500 °C showed overpotentials of 565 mV and 474 mV at 10 mA/cm 2 , respectively. Structural characterization and X-ray photoemission spectroscopy indicate these differences arise from morphology-dependent surface structures that govern catalytic activity.

36 MATERIALS SCIENCE↗

Shape-Selective Catalysts for Fischer-Tropsch Chemistry: January 1, 2001 - December 31, 2008 (Final Report)

Argonne National Laboratory carried out a research program to create, prepare, and evaluate catalysts to promote Fischer-Tropsch (FT) chemistry-specifically, the reaction of hydrogen with carbon monoxide to form long-chain hydrocarbons. In addition to needing high activity, it was desirable that the catalysts have high selectivity and stability with respect to both mechanical strength and aging properties. It was desired that selectivity be directed toward producing diesel fraction components and avoiding excess yields of both light hydrocarbons and heavy waxes. The original goal was to produce shape-selective catalysts that had the potential to limit the formation of long-chain products and yet retain the active metal sites in a protected 'cage.' This cage would also restrict their loss by attrition during use in slurry-bed reactors. The first stage of this program was to prepare and evaluate iron-containing particulate catalysts. Such catalysts were prepared with silica-containing fractal cages. The activity and strength was essentially the same as that of catalysts without the cages. Since there was no improvement, the program plan was modified as discussed below. A second experimental stage was undertaken to prepare and evaluate active FT catalysts formed by atomic-layer deposition [ALD] of active components on supported membranes and particulate supports. The concept was that of depositing active metals (i.e. ruthenium, iron or cobalt) upon membranes with well defined flow channels of small diameter and length such that the catalytic activity and product molecular weight distribution could be controlled. In order to rapidly evaluate the catalytic membranes, the ALD coating processes were performed in an 'exploratory mode' in which ALD procedures from the literature appropriate for coating flat surfaces were applied to the high surface area membranes. Consequently, the Fe and Ru loadings in the membranes were likely to be smaller than those expected for complete monolayer coverage. In addition, there was likely to be significant variation in the Fe and Ru loading among the membranes due to difficulties in nucleating these materials on the aluminum oxide surfaces. The first series of experiments using coated membranes demonstrated that the technology needed further improvement. Specifically, observed catalytic FT activity was low. This low activity appeared to be due to: (1) low available surface area, (2) atomic deposition techniques that needed improvements, and (3) insufficient preconditioning of the catalyst surface prior to FT testing. Therefore, experimentation was expanded to the use of particulate silica supports having defined channels and reasonably high surface area. An effective FT catalyst consisting of ALD-deposited Co and Pt on a silica support has been prepared and demonstrated. This catalyst was more effective than a similar catalyst deposited upon a support of ALD-deposited Al 2 O 3 on silica. This result implies that the deposition of Al 2 O 3 to form a support is not as effective as desired. The addition of Pt as a Co-containing catalyst promoter has been demonstrated; it appears to primarily affect the catalyst pre-conditioning step. Co on Al 2 O 3 catalyst prepared by the Center for Applied Energy Research (CAER) is more effective than Argonne-prepared ALD-deposited Co on ALD-deposited Al 2 O 3 catalyst. The FT activity of ALD-coated Co catalyst on Al 2 O 3 is about linear with Co level from about 9 to 25%. A cooperative research effort was undertaken to test the deposition of platinum on Co FT catalysts; this Pt influences the effectiveness of catalyst conditioning and its continuing activity. In summary, the ALD Pt at a low concentration (0.1 wt %) was as effective as that of the wet chemical deposition technique of CAER (specifically incipient deposition on a Co catalyst that had been prepared and calcined before the Pt deposition.) The ALD technique appeared to be nominally better than the incipient wetness technique that involved co-deposition of Pt and Co prior to calcination. The activation energy of the rate of CO conversion was tightly grouped about an average of 29.2 Kcal/mol when all of the Co-containing catalysts other than those with high Pt promoter levels were taken into account; this implies a uniform reaction mechanism. Catalysts containing Pt and Ru that were ALD-deposited on an ALD-Al 2 O 3 coated catalyst support were found to be relatively inactive. Additional tests were made with a low concentration (0.1 wt %) of Ru or Ir deposited on the reference Co catalyst. The Ir coated catalysts were particularly effective. In support of the above, there was an opportunity to undertake a study of cobalt/promoter/support interaction using the Advanced Photon Source (APS) of Argonne. A number of catalysts (including reference cobalt oxide and iron oxides) were tested using temperature programmed EXAFS/XANES experiments.

08 HYDROGEN↗

High Purity Hydrogen Production with In-Situ Carbon Dioxide and Sulfur Capture in a Single Stage Reactor

Enhancement in the production of high purity hydrogen (H 2 ) from fuel gas, obtained from coal gasification, is limited by thermodynamics of the water gas shift (WGS) reaction. However, this constraint can be overcome by conducting the WGS in the presence of a CO 2 -acceptor. The continuous removal of CO 2 from the reaction mixture helps to drive the equilibrium-limited WGS reaction forward. Since calcium oxide (CaO) exhibits high CO 2 capture capacity as compared to other sorbents, it is an ideal candidate for such a technique. The Calcium Looping Process (CLP) developed at The Ohio State University (OSU) utilizes the above concept to enable high purity H 2 production from synthesis gas (syngas) derived from coal gasification. The CLP integrates the WGS reaction with insitu CO 2 , sulfur and halide removal at high temperatures while eliminating the need for a WGS catalyst, thus reducing the overall footprint of the hydrogen production process. The CLP comprises three reactors - the carbonator, where the thermodynamic constraint of the WGS reaction is overcome by the constant removal of CO 2 product and high purity H 2 is produced with contaminant removal; the calciner, where the calcium sorbent is regenerated and a sequestration-ready CO 2 stream is produced; and the hydrator, where the calcined sorbent is reactivated to improve its recyclability. As a part of this project, the CLP was extensively investigated by performing experiments at lab-, bench- and subpilot-scale setups. A comprehensive techno-economic analysis was also conducted to determine the feasibility of the CLP at commercial scale. This report provides a detailed account of all the results obtained during the project period.

01 COAL, LIGNITE, AND PEAT↗

Sum Frequency Generation Studies of Hydrogenation Reactions on Platinum Nanoparticles

Sum Frequency Generation (SFG) vibrational spectroscopy is used to characterize intermediate species of hydrogenation reactions on the surface of platinum nanoparticle catalysts. In contrast to other spectroscopy techniques which operate in ultra-high vacuum or probe surface species after reaction, SFG collects information under normal conditions as the reaction is taking place. Several systems have been studied previously using SFG on single crystals, notably alkene hydrogenation on Pt(111). In this thesis, many aspects of SFG experiments on colloidal nanoparticles are explored for the first time. To address spectral interference by the capping agent (PVP), three procedures are proposed: UV cleaning, H2 induced disordering and calcination (core-shell nanoparticles). UV cleaning and calcination physically destroy organic capping while disordering reduces SFG signal through a reversible structural change by PVP.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Integrated Waste Treatment Unit (IWTU) Input Coal Analyses and Off-Gass Filter (OGF) Content Analyses

A full engineering scale Fluidized Bed Steam Reformer (FBSR) system is being used at the Idaho Nuclear Technology and Engineering Center (INTEC) to stabilize acidic Low Activity Waste (LAW) known as Sodium Bearing Waste (SBW). The INTEC facility, known as the Integrated Waste Treatment Unit (IWTU), underwent an Operational Readiness Review (ORR) and a Technology Readiness Assessment (TRA) in March 2014. The IWTU began non-radioactive simulant processing in late 2014 and by January, 2015 ; the IWTU had processed 62,000 gallons of simulant. The facility is currently in a planned outage for inspection of the equipment and will resume processing simulated waste feed before commencing to process 900,000 gallons of radioactive SBW. The SBW acidic waste will be made into a granular FBSR product (carbonate based) for disposal in the Waste Isolation Pilot Plant (WIPP). In the FBSR process calcined coal is used to create a CO2 fugacity to force the waste species to convert to carbonate species. The quality of the coal, which is a feed input, is important because the reactivity, moisture, and volatiles (C,H,N,O, and S) in the coal impact the reactions and control of the mineralizing process in the primary steam reforming vessel, the Denitration and Mineralizing Reformer (DMR). Too much moisture in the coal can require that additional coal be used. However since moisture in the coal is only a small fraction of the moisture from the fluidizing steam this can be self-correcting. If the coal reactivity or heating value is too low then the coal feed-rate needs to be adjusted to achieve the desired heat generation. Too little coal and autothermal heat generation in the DMR cannot be sustained and/or the carbon dioxide fugacity will be too low to create the desired carbonate mineral species. Too much coal and excess S and hydroxide species can form. Excess sulfur from coal that (1) is too rich in sulfur or (2) from overfeeding coal can promote wall scale and contribute to corrosion in process piping and materials, in excessive off-gas absorbent loading, and in undesired process emissions. The ash content of the coal is important as the ash adds to the DMR and other vessel products which affect the final waste product mass and composition. The amount and composition of the ash also affects the reaction kinetics. Thus ash content and composition contributes to the mass balance. In addition, sodium, potassium, calcium, sulfur, and maybe silica and alumina in the ash may contribute to wall-scale formation. Sodium, potassium, and alumina in the ash will be overwhelmed by the sodium, potassium, and alumina from the feed but the impact from the other ash components needs to be quantified. A maximum coal particle size is specified so the feed system does not plug and a minimum particle size is specified to prevent excess elutriation from the DMR to the Process Gas Filter (PGF). A vendor specification was used to procure the calcined coal for IWTU processing. While the vendor supplied a composite analysis for the 22 tons of coal (Appendix A), this study compares independent analyses of the coal performed at the Savannah River National Laboratory (SRNL) and at the National Energy Technology Laboratory (NETL). Three supersacks a were sampled at three different heights within the sack in order to determine within bag variability and between bag variability of the coal. These analyses were also compared to the vendor’s composite analyses and to the coal specification. These analyses were also compared to historic data on Bestac coal analyses that had been performed at Hazen Research Inc. (HRI) between 2004-2011.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Cost-effective Manufacturing and Morphological Stabilization of Nanostructured Cathodes for Commercial SOFCs

The overall goals of the program were to develop methods for preparing and stabilizing SOFC electrodes by infiltration that can be manufactured on a practical scale, then transfer those methods to cells in stacks. Cathodes prepared by infiltration of nanoparticles into a porous scaffold of the electrolyte have demonstrated outstanding electrochemical performance and mechanical strength but are difficult to manufacture due to the large number of infiltration steps required to produce a conductive composite and show poor stability due to sintering of the nanoparticles. At Penn, the main goal was to develop a fabrication method that uses only a small number of infiltration steps. Infiltration with molten salts and electrodeposition were pursued but deemed impractical. A method in which an electronically conductive scaffold consisted of a composite of a mixed conductor, LSF (La 0.9 Sr 0.1 FeO 3 ), with yttria-stabilized zirconia (YSZ) was found to be promising. While some cation mixing between LSF and YSZ was observed during calcination, there was no evidence for new phases in XRD and incorporation of Zr into the perovskite could be minimized by reducing the Sr content of the LSF. To stabilize nanoparticles infiltrated into the LSF-YSZ composite scaffold, the USC team examined the effects of Atomic Layer Deposition with ZrO 2 and infiltrated nanoparticles. Significantly enhanced stability was observed with the infiltrated nanoparticles. The FuelCell Energy team prepared 4”x4” cells in which an LSF-YSZ composite scaffold was cofired with the YSZ electrolyte and infiltrated with LSCF nanoparticles. Apparently because the LSF-YSZ scaffold layer was very thin in this case, the cation mixing that occurred during calcination resulted in a poor scaffold-electrolyte interface which caused reduced performance.

36 MATERIALS SCIENCE↗

Inventory and Waste Characterization Status Report and OWL Update.

This report represents completion of milestone deliverable M2SF-18SNO10309013 "Inventory and Waste Characterization Status Report and OWL Update that reports on FY2018 activities for the work package (WP) SF-18SNO1030901. This report provides the detailed final information for completed FY2018 work activities for WP SF-18SN01030901, and a summary of priorities for FY2019. This status report on FY2018 activities includes evaluations of waste form characteristics and waste form performance models, updates to the OWL development, and descriptions of the two planned management processes for the OWL. Updates to the OWL include an updated user's guide, additions to the OWL database content for wastes and waste forms, results of the Beta testing and changes implemented from it. There are two processes being planned in FY2018, which will be implemented in FY2019. One process covers methods for interfacing with the DOE SNF DB (DOE 2007) at INL on the numerous entries for DOE managed SNF, and the other process covers the management of updates to, and version control/archiving of, the OWL database. In FY2018, we have pursued three studies to evaluate/redefine waste form characteristics and/or performance models. First characteristic isotopic ratios for various waste forms included in postclosure performance studies are being evaluated to delineate isotope ratio tags that quantitatively identify each particular waste form. This evaluation arose due to questions regarding the relative contributions of radionuclides from disparate waste forms in GDSA results, particularly, radionuclide contributions of DOE-managed SNF vs HLW glass. In our second study we are evaluating the bases of glass waste degradation rate models to the HIP calcine waste form. The HIP calcine may likely be a ceramic matrix material, with multiple ceramic phases with/without a glass phase. The ceramic phases are likely to have different degradation performance from the glass portion. The distribution of radionuclides among those various phases may also be a factor in the radionuclide release rates. Additionally, we have an ongoing investigation of the performance behavior of TRISO particle fuels and are developing a stochastic model for the degradation of those fuels that accounts for simultaneous corrosion of the silicon carbide (SiC) layer and radionuclide diffusion through it. The detailed model of the TRISO particles themselves, will be merged with models of the degradation behavior(s) of the graphite matrix (either prismatic compacts or spherical "pebbles") containing the particles and the hexagonal graphite elements holding the compacts.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

MIS High Purity Plutonium Oxide Metal Oxidation Product MT1490 (SSR125): Final Report

A high purity plutonium dioxide material from the Material Identification and Surveillance (MIS) Program inventory has been studied with regard to gas generation and corrosion in a storage environment. Sample MT1490 represents process plutonium oxides from several metal oxidation operations that are currently stored in 3013 containers. This study followed over time, the gas pressure of a sample with nominally 0.5 weight percent water in a sealed container with an internal volume scaled to 1/500 th of the volume of a 3013 container. The sample was a mixture of as-received material, material calcined at 800°C and material calcined at 950°C. This material contained 87% plutonium with no major impurities. Gas compositions were measured periodically over a nine year period. The maximum observed gas pressure of 118 kPa was reached during the ninth year. The increase over the initial pressure of 95 kPa was primarily due to generation of nitrogen and hydrogen gas. Oxygen was a minor component of the headspace gas. At the completion of the study, the inner bucket showed signs of corrosion, including pitting, in the container material contact region.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

MIS High-Purity Plutonium Oxide Oxalate Precipitation/Calcination Product PBO-47-09-012-023 (Final Report)

A high-purity fuel-grade plutonium dioxide material from the Material Identification and Surveillance (MIS) Program inventory has been studied with regard to gas generation and corrosion in a storage environment. Sample PBO-47-09-012-023 originated from the Hanford continuous oxalate precipitation and calcination process and represents plutonium oxides from multiple processes currently stored in 3013 containers. After calcination to 950°C, the material contained 87.5% plutonium/americium with no major impurities. This study followed over time the gas pressure of a sample with nominally 0.5 wt% water in a sealed container with an internal volume scaled to 1/400 th of the volume of a 3013 container. Gas compositions were measured periodically over a three year period. The maximum observed gas pressure was 96 kPa. The increase over the initial pressure was primarily due to generation of hydrogen (5.7 kPa) and nitrogen (2 kPa) gas. Oxygen was a minor component of the initial headspace gas and was depleted. At the completion of the study, the internal components of the sealed container did not show significant signs of corrosion.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Hydrogenous Content in Residues from Aqueous Chloride Pu and Am Recovery Operations

Byproduct residues generated from Aqueous Chloride Pu and Am recovery operations at Los Alamos National Laboratory have been investigated and determined to contain high weight % chloride salts and minimal hydrogen content. Hydrogen content is the result of limited surface area adsorption of ambient moisture. The assumption used in technical analysis NCS-TECH-19-029 to model potentially hydrogenous items as mixtures of polyethylene is shown to be overly conservative. Our results and literature precedent indicate that water adsorption of 1-3 % by weight is expected for hydroxide cakes and Pu oxides, and a conservative bounding assumption for these materials is 5% water by weight. LOH results for a dissolution heel stored long term showed 6.25% weight loss, which was conservatively assumed to be water. A conservative bounding assumption for dissolution heels is 8 wt.% water content. This equates to 0.55 % hydrogen by weight for hydroxide cakes, and 0.88% hydrogen by weight for dissolution heels. The bulk composition of dissolution heels reflects the composition of the original byproduct feed material, chloride salts of potassium, sodium, magnesium and calcium. The bulk composition of calcined hydroxide precipitation residues is composed of potassium chloride as a result of potassium hydroxide neutralization of hydrochloric acid solutions. Metal hydroxides generated during the hydroxide precipitation process are decomposed under the conditions of calcination to metal oxide forms.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Cost-effective Manufacturing and Morphological Stabilization of Nanostructured Cathodes for Commercial Solid Oxide Fuel Cells (SOFCs) [Slides]

The overall goals of the program were to develop methods for preparing and stabilizing SOFC electrodes by infiltration that can be manufactured on a practical scale, then transfer those methods to cells in stacks. Cathodes prepared by infiltration of nanoparticles into a porous scaffold of the electrolyte have demonstrated outstanding electrochemical performance and mechanical strength but are difficult to manufacture due to the large number of infiltration steps required to produce a conductive composite and show poor stability due to sintering of the nanoparticles. At Penn, the main goal was to develop a fabrication method that uses only a small number of infiltration steps. Infiltration with molten salts and electrodeposition were pursued but deemed impractical. A method in which an electronically conductive scaffold consisted of a composite of a mixed conductor, LSF (La 0.9 Sr 0.1 FeO 3 ), with yttria-stabilized zirconia (YSZ) was found to be promising. While some cation mixing between LSF and YSZ was observed during calcination, there was no evidence for new phases in XRD and incorporation of Zr into the perovskite could be minimized by reducing the Sr content of the LSF. To stabilize nanoparticles infiltrated into the LSF-YSZ composite scaffold, the USC team examined the effects of Atomic Layer Deposition with ZrO 2 and infiltrated nanoparticles. Significantly enhanced stability was observed with the infiltrated nanoparticles. The FuelCell Energy team prepared 4”x4” cells in which an LSF-YSZ composite scaffold was cofired with the YSZ electrolyte and infiltrated with LSCF nanoparticles. Apparently because the LSF-YSZ scaffold layer was very thin in this case, the cation mixing that occurred during calcination resulted in a poor scaffold-electrolyte interface which caused reduced performance.

30 DIRECT ENERGY CONVERSION↗

Assessment of Nuclear Energy to Support Negative Emission Technologies

The feasibility and performance of nuclear energy coupled with Negative Emission Technology (NET) processes were investigated in this report. Three overarching questions from nuclear NET systems guided this research: which NET would be able to use heat and/or electricity from nuclear power plants (NPPs); what is the performance and cost of a nuclear NET system; and what would be the market outlook for this system? Among the various NETs that are actively being developed, several were found to potentially benefit from coupling with an NPP via (1) large amounts of decarbonized and constant-output electricity; (2) free waste heat or cheap low-temperature heat; or (3) high-temperature heat. NPPs were found to be compatible with Direct Air Capture (DAC) systems, and a detailed techno-economic analysis of coupled NPP&DAC systems was performed. Preliminary analysis also indicated that biomass and water-based NETs are potentially compatible with NPPs, but further work is needed to quantify the performance of these nuclear NET systems. Design and performance analyses were completed for both liquid solvent DAC (L-DAC) and solid sorbent DAC (S-DAC) technologies. A 1.0-GWth NPP coupled with L-DAC and S-DAC was found to be able to capture 12–15 Mt CO 2 /yr and 1.0–1.5 Mt CO 2 /yr, respectively. While the L-DAC process enables much greater CO 2 capture than the S-DAC process when both are sized with a 1 GWth NPP, the NPP&L-DAC system considered also requires >2 GWth natural gas oxy-combustion to reach adequate temperature in the calciner. CO 2 generated from natural gas combustion is also captured as part of the calcination process, in addition to the CO 2 captured from air, resulting in overall CO 2 sequestration of close to 30% more than what is captured from air. The cost of carbon capture calculated with the levelized cost of DAC (LCOD) had a range of $\$170–260$/tCO 2 for NPP&L-DAC systems and a range of $\$650–680$/tCO 2 for NPP&S-DAC systems. For both DAC systems, the NPP provides economic benefit when compared to previous National Energy Technology Laboratory (NETL) studies of non-nuclear DAC systems, leading to reduction of LCOD by 5–7% for L-DAC, and 8–13% for S-DAC. For the NPP&DAC systems, a preliminary market analysis reviewed potential CO 2 market prices and eligibility for incentives. The estimated potential revenues for CO 2 capture (coming from federal incentive, CO 2 commodity markets, or offset market) is in the range of $\$170–979$ tCO 2 , and the results show that because of lower LCOD, the NPP&L-DAC process would be more attractive to a market than the NPP&S-DAC process. The large investment needed for NPP&DAC processes would require long-term certainty of sufficient market size, CO 2 prices, and incentives. Enabling NPPs to ramp DAC operation up or down based on electricity market price is not expected to significantly increase revenues of the NPP&DAC system. This is because the revenues from CO 2 sequestration are required to be very high to justify the deployment and continuous operation of the very expensive DAC technologies. In this analysis, several new research questions were uncovered, and follow-up analyses are recommended for further investigation, including a detailed feasibility study of NPP coupled with other NET systems such as biomass pyrolysis and gasification with carbon capture and storage, and seawater carbon capture.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗