Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Alloy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

Polishing-assisted galvanic corrosion in the dissimilar friction stir welded joint of AZ31 magnesium alloy to 2024 aluminum alloy

Galvanic corrosion of a dissimilar friction stir welded 2024-T3 Al/AZ31B-H24 Mg joint prepared using a water-based and a non-water-based polishing solution was characterized. Microstructure and the distribution of chemical elements were analyzed using optical microscopy, scanning electron microscopy and energy dispersive X-ray spectroscopy. The stir zone polished using water-based solution was observed to be much more susceptible to galvanic corrosion attack than that obtained using non-water-based polishing solution. The location of corrosion attack was observed in the narrow regions of AZ31 Mg alloy adjacent to Al2024 regions in the stir zone. The occurrence of galvanic corrosion was due to the formation of Mg/Al galvanic couples with a small ratio of anode-to-cathode surface area. The corrosion product was primarily the porous magnesium hydroxide with characteristic microcracks and exhibited a low microhardness value.

36 MATERIALS SCIENCE↗

High Thermoelectric Performance in PbSe–NaSbSe 2 Alloys from Valence Band Convergence and Low Thermal Conductivity

PbSe is an attractive thermoelectric material due to its favorable electronic structure, high melting point, and lower cost compared to PbTe. Herein, the hitherto unexplored alloys of PbSe with NaSbSe 2 (NaPb m SbSe m+2 ) are described and the most promising p-type PbSe-based thermoelectrics are found among them. Surprisingly, it is observed that below 500 K, NaPb m SbSe m+2 exhibits unorthodox semiconducting-like electrical conductivity, despite possessing degenerate carrier densities of ≈10 20 cm -3 . Here, it is shown that the peculiar behavior derives from carrier scattering by the grain boundaries. It is further demonstrated that the high solubility of NaSbSe 2 in PbSe augments both the thermoelectric properties while maintaining a rock salt structure. Namely, density functional theory calculations and photoemission spectroscopy demonstrate that introduction of NaSbSe 2 lowers the energy separation between the L- and Σ-valence bands and enhances the power factors under 700 K. The crystallographic disorder of Na + , Pb 2+ , and Sb 3+ moreover provides exceptionally strong point defect phonon scattering yielding low lattice thermal conductivities of 1–0.55 W m -1 K -1 between 400 and 873 K without nanostructures. As a consequence, NaPb 10 SbSe 12 achieves maximum ZT ≈1.4 near 900 K when optimally doped. More importantly, NaPb 10 SbSe 12 maintains high ZT across a broad temperature range, giving an estimated record ZT avg of ≈0.64 between 400 and 873 K, a significant improvement over existing p-type PbSe thermoelectrics.

36 MATERIALS SCIENCE↗

Morphology, structure, and chemistry of nanoclusters in a mechanically alloyed nanostructured ferritic steel

Nanostructured ferritic steels have excellent high temperature creep properties and radiation tolerance due to the presence of a high density of Ti-Y-O-enriched nanoclusters. The morphology of the nanoclusters is found to be consistent with a truncated rhombic dodecahedron defined by the {l_brace}100{r_brace} and {l_brace}110{r_brace} planes in the Fe matrix. The derived symmetry and the compositional information indicate that the nanoclusters are inconsistent with the cubic Y2Ti2O7 or the polymorphs of Y2TiO5 phase. Possible structural models are discussed.

36 MATERIALS SCIENCE↗

Thermomechanical treatment for improved neutron irradiation resistance of austenitic alloy (Fe-21Cr-32Ni)

An optimized thermomechanical treatment (TMT) applied to austenitic alloy 800H (Fe-21Cr-32Ni) had shown significant improvements in corrosion resistance and basic mechanical properties. This study examined its effect on radiation resistance by irradiating both the solution-annealed (SA) and TMT samples at 500 degrees C for 3 dpa. Microstructural characterization using transmission electron microscopy revealed that the radiation-induced Frank loops, voids, and y'-Ni3(Ti,Al) precipitates had similar sizes between the SA and TMT samples. The amounts of radiation-induced defects and more significantly y' precipitates, however, were reduced in the TMT samples. These reductions would approximately reduce by 40.9% the radiation hardening compared to the SA samples. This study indicates that optimized-TMT is an economical approach for effective overall property improvements.

99 GENERAL AND MISCELLANEOUS↗

Magnesium Alloy ZK60 Tubing made by Shear Assisted Processing and Extrusion (ShAPE)

ZK60 Magnesium tubing has been friction extruded from as-cast billets and T5 conditioned bars using Shear Assisted Processing and Extrusion (ShAPE). Tubes having an outer diameter of 50.8 mm and wall thickness of 1.9 mm were extruded with >20 times less ram force compared to conventional extrusion due to the unique shearing conditions and tooling inherent to ShAPE. Microstructures of the as-cast billet and T5 bar feedstock materials were significantly different from each other in terms of grain size, texture, and second phase distribution; yet the resulting microstructures after ShAPE were remarkably similar. An average grain size of 4-5 microns, 20o tilt of basal texture away from the extrusion axis, and refined second phases having a uniform distribution were achieved independent of the feedstock material. Hardness for as-extruded and artificially aged tubes are presented with isotropic behavior explained by detailed microstructural analysis. This work suggests that bulk ZK60 magnesium alloys extrusions may be fabricated in a single step, with microstructures that are unobtainable with conventional extrusion.

Friction Stir Extrusion, Friction Consolidation an↗

Atomic dynamics in molten AlCu alloys of different compositions and at different temperatures by cold neutron scattering

The atomic motions in molten Al1-xCux (x=0.10, 0.171 and 0.25) around the eutectic composition (x=0.171) were studied by cold neutron inelastic scattering at three different temperatures (973 K, 1173 K and 1373 K). An alloy of eutectic composition containing the 63Cu isotope was also studied. Self-diffusion coefficients for the Cu ions were determined from the width of quasielastic peaks and were found to decrease slightly with increasing Cu concentration. Longitudinal current correlation functions Jl(Q,E) exhibit at all temperatures and at all compositions a shoulder at energies below 10 meV and one main maximum at higher energies. These features can be interpreted in terms of excitations of acoustic and optic nature. The shape of Jl(Q,E) is sensitive to composition, being considerably more structured for larger Cu content. This can be coupled to the existence of a prepeak in the measured zeroth moment of dynamic scattering function indicating an increased chemical ordering with increasing Cu concentration for all temperatures. Indications for an existence of a liquid–liquid phase transition are presented.

36 MATERIALS SCIENCE↗

Yield strength dependence on strain rate of molybdenum-alloy nanofibers

The yield strength dependence on strain rate was studied for molybdenum-alloy nanofibers with varying initial dislocation density at three different pre-strain levels. In-situ tensile experiments at three displacement rates were carried out in a scanning electron microscope. Yield strength and its scatter decreased as a function of the pre-strain level for different displacement rates. A statistical model was used to analyze the results, and a negative strain rate dependence was inferred from the yield experiments. This finding suggests the need for theoretical investigations since classical models such as dynamic strain aging may have limitations at such nanoscales.

36 MATERIALS SCIENCE↗

Using coupled micropillar compression and micro-Laue diffraction to investigate deformation mechanisms in a complex metallic alloy Al{sub 13}Co{sub 4}

In this study, we have used in-situ micro-Laue diffraction combined with micropillar compression of focused ion beam milled Al{sub 13}Co{sub 4} complex metallic alloy to investigate the evolution of deformation in Al{sub 13}Co{sub 4}. Streaking of the Laue spots shows that the onset of plastic flow occurs at stresses as low as 0.8 GPa, although macroscopic yield only becomes apparent at 2 GPa. The measured misorientations, obtained from peak splitting, enable the geometrically necessary dislocation density to be estimated as 1.1 × 10{sup 13 }m{sup −2}.

36 MATERIALS SCIENCE↗

Pressure tunes electrical resistivity by four orders of magnitude in amorphous Ge[subscript 2]Sb[subscript 2]Te[subscript 5] phase-change memory alloy

Ge-Sb-Te-based phase-change memory is one of the most promising candidates to succeed the current flash memories. The application of phase-change materials for data storage and memory devices takes advantage of the fast phase transition (on the order of nanoseconds) and the large property contrasts (e.g., several orders of magnitude difference in electrical resistivity) between the amorphous and the crystalline states. Despite the importance of Ge-Sb-Te alloys and the intense research they have received, the possible phases in the temperature-pressure diagram, as well as the corresponding structure-property correlations, remain to be systematically explored. In this study, by subjecting the amorphous Ge{sub 2}Sb{sub 2}Te{sub 5} (a-GST) to hydrostatic-like pressure (P), the thermodynamic variable alternative to temperature, we are able to tune its electrical resistivity by several orders of magnitude, similar to the resistivity contrast corresponding to the usually investigated amorphous-to-crystalline (a-GST to rock-salt GST) transition used in current phase-change memories. In particular, the electrical resistivity drops precipitously in the P = 0 to 8 GPa regime. A prominent structural signature representing the underlying evolution in atomic arrangements and bonding in this pressure regime, as revealed by the ab initio molecular dynamics simulations, is the reduction of low-electron-density regions, which contributes to the narrowing of band gap and delocalization of trapped electrons. At P > 8 GPa, we have observed major changes of the average local structures (bond angle and coordination numbers), gradually transforming the a-GST into a high-density, metallic-like state. This high-pressure glass is characterized by local motifs that bear similarities to the body-centered-cubic GST (bcc-GST) it eventually crystallizes into at 28 GPa, and hence represents a bcc-type polyamorph of a-GST.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Computational exploration of biomedical HfNbTaTiZr and Hf 0.5 Nb 0.5 Ta 0.5 Ti 1.5 Zr refractory high-entropy alloys

Refractory high entropy alloys (RHEAs) have been proven to be a potential candidate in the biomedical field due to their balanced mechanical properties and biocompatible composition. Recent experimental findings show that RHEAs like HfNbTaTiZr and Hf 0.5 Nb 0.5 Ta 0.5 Ti 1.5 Zr have good mechanical properties such as high polarization and wear resistance than others which establish them as potential materials for biomedical application. In this work, we performed first-principles density functional theory calculations on the mechanical and thermal properties of HfNbTaTiZr and Hf 0.5 Nb 0.5 Ta 0.5 Ti 1.5 Zr. The predicted lattice constant, density, Young's modulus, and Vickers hardness are consistent with the available experimental report, which verifies the accuracy of the applied model. The thermal coefficient of linear expansion of both RHEAs has been investigated by utilizing the Debye theory. The present methods could be applied to study other future RHEAs on exploration of their physical properties.

36 MATERIALS SCIENCE↗