Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AERODYNAMICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

Measurement and analysis of aircraft far-field aerodynamic noise

A systematic investigation of aircraft far-field radiated, aerodynamically generated noise was conducted. The test phase of the original program involved the measurement of the noise produced by five gliding aircraft in an aerodynamically clean configuration during low altitude flyovers. These aircraft had gross weights that ranged from 5785 to 173 925N (1300 to 39,000 pounds), fly-by velocities from 30 to 98.5m/sec (58 to 191.5 knots or 98 to 323 ft/sec) and wing aspect ratios from 6.59 to 18.25. The results of these measurements were used to develop an equation relating aerodynamic noise to readily evaluated physical and operational parameters of the aircraft. A non-dimensional frequency spectrum, based on the mean wing thickness, was also developed.

Healy, G. J.↗

Aerodynamics of jet flap and rotating cylinder flap STOL concepts

The aerodynamic effectiveness of various propulsive lift concepts to provide for the low speed performance and control required for short takeoff and landing aircraft is discussed. The importance of the interrelationship between the propulsion system and aerodynamic components of the aircraft is stressed. The relative effectiveness of different lift concepts was evaluated through static and wind tunnel tests of various aerodynamic models and propulsion components, simulations of aircraft, and in some cases, flight testing of research aircraft incorporating the concepts under study. Results of large scale tests of lift augmentation devices are presented. The results of flight tests of STOL research aircraft with augmented jet flaps and rotating cylinder flaps are presented to show the steeper approach flight paths at low forward speeds.

Cook, W. L.↗

Development of a superconductor magnetic suspension and balance prototype facility for studying the feasibility of applying this technique to large scale aerodynamic testing

The basic research and development work towards proving the feasibility of operating an all-superconductor magnetic suspension and balance device for aerodynamic testing is presented. The feasibility of applying a quasi-six-degree-of freedom free support technique to dynamic stability research was studied along with the design concepts and parameters for applying magnetic suspension techniques to large-scale aerodynamic facilities. A prototype aerodynamic test facility was implemented. Relevant aspects of the development of the prototype facility are described in three sections: (1) design characteristics; (2) operational characteristics; and (3) scaling to larger facilities.

Zapata, R. N.↗

Computer programs for calculating the static longitudinal aerodynamic characteristics of wing-body-tail configurations

Four computer programs developed to calculate the longitudinal aerodynamic characteristics of wing-body and wing-body-tail combinations are presented. The R1307 program is based on a linear method and is limited to the small range of angles of attack for which the lift and moment characteristics of wings and bodies are linear with angle of attack. The CRSFLW program is based on a crossflow method of predicting the forces and moments on bodies alone or wing-body combinations over a large angle of attack range. The SUBSON program predicts the longitudinal aerodynamic characteristics of wing-body-tail combinations at subsonic speeds and at angles of attack for which symmetrical pairs of vortices are shed from the body nose and the leading and side edges of the lifting surfaces. Program SUPSON predicts the longitudinal aerodynamic characteristics of wing-body-tail combinations at supersonic speeds in the same angle-of-attack range. A description of the use of each program, instructions for preparation of input, a description of the output, program listings, and sample cases for each program are included.

Mendenhall, M. R.↗

Experimental aerodynamic characteristics for a cylindrical body of revolution with side strakes and various noses at angles of attack from 0 degrees to 58 degrees and Mach numbers from 0.6 to 2.0

For a body of revolution with afterbody side strakes, an experimental investigation was conducted in the Ames 6- by 6-Foot Wind Tunnel to determine the effects on the aerodynamic characteristics of forebody geometry, nose strakes, body side strakes, Reynolds number, Mach number, and angle of attack. Aerodynamic force and moment characteristics were measured for the straked cylindrical afterbody (cylinder fineness ratio of 7) with tangent ogive noses of fineness ratio 2.5 to 5.0. In addition, the straked cylinder afterbody was tested with an ogive nose having a rounded tip and an ogive nose with two different nose strake arrangements. The data demonstrate that the aerodynamic characteristics for a body of revolution with side strakes can be significantly affected by changes in nose fineness ratio, nose bluntness, Reynolds number, Mach number, and, of course, angle of attack. Removing the strakes from the cylindrical aftersection greatly decreased the lift, but this removal hardly changed the maximum magnitudes of the undesirable side forces that developed at angles of attack greater than about 25 deg for subsonic Mach numbers.

Jorgensen, L. H.↗

Acoustic and aerodynamic performance of a 1.83-meter (6-ft) diameter 1.25-pressure-ratio fan (QF-8)

A 1.25-pressure-ratio 1.83-meter (6-ft) tip diameter experimental fan stage with characteristics suitable for engine application on STOL aircraft was tested for acoustic and aerodynamic performance. The design incorporated proven features for low noise, including absence of inlet guide vanes, low rotor blade tip speed, low aerodynamic blade loading, and long axial spacing between the rotor and stator blade rows. The fan was operated with five exhaust nozzle areas. The stage noise levels generally increased with a decrease in nozzle area. Separation of the acoustic one-third octave results into broadband and pure-tone components showed the broadband noise to be greater than the corresponding pure-tone components. The sideline perceived noise was highest in the rear quadrants. The acoustic results of QF-8 were compared with those of two similar STOL application fans in the test series. The QF-8 had somewhat higher relative noise levels than those of the other two fans. The aerodynamic results of QF-8 and the other two fans were compared with corresponding results from 50.8-cm (20-in.) diam scale models of these fans and design values. Although the results for the full-scale and scale models of the other two fans were in reasonable agreement for each design, the full-scale fan QF-8 results showed poor performance compared with corresponding model results and design expectations. Facility effects of the full-scale fan QF-8 installation were considered in analyzing this discrepancy.

Woodward, R. P.↗

Two-stage, low noise advanced technology fan. Volume 2: Aerodynamic data

Aerodynamic data from static tests of a two-stage advanced technology fan designed to minimize noise are presented. Fan design conditions include delivery of 209.1kg/sec/sq m (42.85 lbm/sec/sq ft) specific corrected flow at an overall pressure ratio of 1.9 and an adiabatic efficiency of 85.3 percent. The 0.836m (2.74ft) diameter first stage rotor has a hub/tip ratio of 0.4 and 365.8m/sec (1200ft/sec) design tip speed. In addition to the moderate tip speed and pressure rise per stage, other noise control design features involve widely spaced blade rows and proper selection of blade-vane ratios. Aerodynamic data are presented for tests with unifrom and with hub and tip radially distorted inlet flow. Aerodynamic data are also presented for tests of this fan with acoustic treatments, including acoustically treated casing walls, a flowpath exit acoustic ring, and a translating centerbody sonic inlet device. A complete tabulation of the overall performance data, the blade element data, and the power spectral density information relating to turbulence levels generated by the sonic inlet obtained during these tests is included. For vol. 1, see N74-33789.

Harley, K. G.↗

Applications of vortex lattice theory to preliminary aerodynamic design

Some applications of the vortex-lattice theory to the preliminary aerodynamic design and analysis of subsonic aircraft were presented. These methods include the Rockwell-Tulinius vortex-lattice theory for estimating aerodynamic characteristics, a Trefftz plane optimization procedure for determining the span loads for minimum induced drag, and a modification of the Trefftz plane procedure to estimate the induced drag for specified span loads. The first two methods are used to aerodynamically design aircraft planforms, twists, and cambers, and the latter method is used to estimate the drag for components such as flaps and control surfaces. Results from the theories for predicting lift and pitching moment, drag due to lift, and the drag of control surfaces are compared with experimental data. This data was obtained on a general aviation model with flaps and a close-coupled canard-wing model.

Paulson, J. W., Jr.↗

The effect of winglets on the static aerodynamic stability characteristics of a representative second generation jet transport model

A baseline wing and a version of the same wing fitted with winglets were tested. The longitudinal aerodynamic characteristics were determined through an angle-of-attack range from -1 deg to 10 deg at an angle of sideslip of 0 deg for Mach numbers of 0.750, 0.800, and 0.825. The lateral aerodynamic characteristics were determined through the same angle-of-attack range at fixed sideslip angles of 2.5 deg and 5 deg. Both configurations were investigated at Reynolds numbers of 13,000,000, per meter (4,000,000 per foot) and approximately 20,000,000 per meter (6,000,000 per foot). The winglet configuration showed slight increases over the baseline wing in static longitudinal and lateral aerodynamic stability throughout the test Mach number range for a model design lift coefficient of 0.53. Reynolds number variation had very little effect on stability.

Jacobs, P. F.↗

On ionospheric aerodynamics

This paper presents theoretical methods to determine the gas dynamic and the electrostatic effects due to the interaction caused by a rapidly moving body in the ionosphere. The principles of the methods are derived from the kinetic theory of collision-free plasma. It is shown that the collective behavior of the collision-free plasma makes it possible to use the fluid approach to treat the problems of ionospheric aerodynamics. Various solutions to the system of fluid and field equations that have direct bearing on the ionospheric aerodynamics are presented and discussed. Physical significances of the mathematical results are stressed. Some outstanding unsolved problems in ionospheric aerodynamics are elaborated and discussed.

Liu, V. C.↗

Fully unsteady subsonic and supersonic potential aerodynamics of complex aircraft configurations for flutter applications

The paper presents a general theory of steady, oscillatory or fully unsteady, subsonic and supersonic aerodynamics for aircraft of arbitrary shape. The finite element method is used to obtain the time functional relationship between aerodynamic potential and its normal derivative (normal wash) in a form suitable for computational analysis. The matrix of the aerodynamic influence coefficients, as necessary for flutter calculations, is obtained as a result. The theory is implemented in a computer program, and some typical results obtained with this program are presented.

Tseng, K.↗

Developments in steady and unsteady aerodynamics for use in aeroelastic analysis and design

A review is given of seven research projects which are aimed at improving the generality, accuracy, and computational efficiency of steady and unsteady aerodynamic theory for use in aeroelastic analysis and design. These projects indicate three major thrusts of current research efforts: (1) more realistic representation of steady and unsteady subsonic and supersonic loads on aircraft configurations of general shape with emphasis on structural-design applications, (2) unsteady aerodynamics for application in active-controls analyses, and (3) unsteady aerodynamics for the frequently critical transonic speed range. The review of each project includes theoretical background, description of capabilities, results of application, current status, and plans for further development and use.

Yates, E. C., Jr.↗

Advanced acoustic and aerodynamic 20-inch fan program

The aerodynamic analyses, mechanical analyses, and stress tests of a 20-inch diameter advanced fan design intended for acoustic investigation by NASA-LeRC are discussed. A high tip speed transonic fan rotor was scaled directly to 20.0 inches (0.508 m) from a 28.74-inch (0.73-m) diameter rotor. A new stator was designed and fabricated for the fan and incorporated with a test rig housing and adapter hardware for installation in the NASA-LeRC Jet Noise Facility for acoustic evaluation. The stator was designed to allow mounting at three axial locations, and the fan, housing, and adapters are reversible so that either the inlet or the exhaust ends of the assembly face the open room of the test facility. Excellent aerodynamic performance is predicted, and a low noise signature is expected since the unique aerodynamic design features of this fan are directly conductive to producing minimum sound power.

Erwin, J. R.↗

COMOC 2: Two-dimensional aerodynamics sequence, computer program user's guide

The COMOC finite element fluid mechanics computer program system is applicable to diverse problem classes. The two dimensional aerodynamics sequence was established for solution of the potential and/or viscous and turbulent flowfields associated with subsonic flight of elementary two dimensional isolated airfoils. The sequence is constituted of three specific flowfield options in COMOC for two dimensional flows. These include the potential flow option, the boundary layer option, and the parabolic Navier-Stokes option. By sequencing through these options, it is possible to computationally construct a weak-interaction model of the aerodynamic flowfield. This report is the user's guide to operation of COMOC for the aerodynamics sequence.

Manhardt, P. D.↗

Effects of unsteady aerodynamics on rotor aeroelastic stability

The effects of unsteady aerodynamics on the stability characteristics of helicopter rotor blades were studied. A simple physical model of each blade was used together with Theodorsen, Loewy, and quasi-steady aerodynamics to derive the equations of motion. The stability analysis comparing the effects of using each of the three theories revealed some significant differences between the Loewy and Theodorsen results. These included increases and decreases in lead-lag damping, localized around integer lead-lag frequencies. It was also shown that the standard method of multi-blade coordinates must be modified for use in conjunction with Loewy aerodynamics.

Kunz, D. L.↗

Single particle aerodynamic relaxation time analyzer

An instrument employing a laser Doppler velocimeter and a microphone to measure the phase lag of the motion of aerosol particulates relative to the motion of the fluid medium within an acoustic field is described. The relaxation times and aerodynamic diameters of the particles or droplets are determined in real time from the measured values of phase lag; thus, the size analysis is independent of the electrostatic charges and refractive indices of the particulates. The instrument is suitable for analyzing the aerodynamic size spectrum of atmospheric particulate pollutants with aerodynamic diameters ranging from 0.1 to 10.0 microns.

Mazumder, M. K.↗

Aerodynamic interference effects on tilting proprotor aircraft

The Green's function method was used to study tilting proprotor aircraft aerodynamics with particular application to the problem of the mutual interference of the wing-fuselage-tail-rotor wake configuration. While the formulation is valid for fully unsteady rotor aerodynamics, attention was directed to steady state aerodynamics, which was achieved by replacing the rotor with the actuator disk approximation. The use of an actuator disk analysis introduced a mathematical singularity into the formulation; this problem was studied and resolved. The pressure distribution, lift, and pitching moment were obtained for an XV-15 wing-fuselage-tail rotor configuration at various flight conditions. For the flight configurations explored, the effects of the rotor wake interference on the XV-15 tilt rotor aircraft yielded a reduction in the total lift and an increase in the nose-down pitching moment. This method provides an analytical capability that is simple to apply and can be used to investigate fuselage-tail rotor wake interference as well as to explore other rotor design problem areas.

Soohoo, P.↗

Index for aerodynamic data from the Bumblebee program

The Bumblebee program, was designed to provide a supersonic guided missile. The aerodynamics program included a fundamental research effort in supersonic aerodynamics as well as a design task in developing both test vehicles and prototypes of tactical missiles. An index of aerodynamic missile data developed in this program is presented.

Cronvich, L. L.↗