Results for “utility scale” — Page 27

NASA NTRS2012

Disturbance Accommodating Adaptive Control with Application to Wind Turbines

Adaptive control techniques are well suited to applications that have unknown modeling parameters and poorly known operating conditions. Many physical systems experience external disturbances that are persistent or continually recurring. Flexible structures and systems with compliance between components often form a class of systems that fail to meet standard requirements for adaptive control. For these classes of systems, a residual mode filter can restore the ability of the adaptive controller to perform in a stable manner. New theory will be presented that enables adaptive control with accommodation of persistent disturbances using residual mode filters. After a short introduction to some of the control challenges of large utility-scale wind turbines, this theory will be applied to a high-fidelity simulation of a wind turbine.

Frost, Susan↗

NASA NTRS2013

Nuclear Thermal Rocket Simulation in NPSS

Four nuclear thermal rocket (NTR) models have been created in the Numerical Propulsion System Simulation (NPSS) framework. The models are divided into two categories. One set is based upon the ZrC-graphite composite fuel element and tie tube-style reactor developed during the Nuclear Engine for Rocket Vehicle Application (NERVA) project in the late 1960s and early 1970s. The other reactor set is based upon a W-UO2 ceramic- metallic (CERMET) fuel element. Within each category, a small and a large thrust engine are modeled. The small engine models utilize RL-10 turbomachinery performance maps and have a thrust of approximately 33.4 kN (7,500 lbf ). The large engine models utilize scaled RL-60 turbomachinery performance maps and have a thrust of approximately 111.2 kN (25,000 lbf ). Power deposition profiles for each reactor were obtained from a detailed Monte Carlo N-Particle (MCNP5) model of the reactor cores. Performance factors such as thermodynamic state points, thrust, specific impulse, reactor power level, and maximum fuel temperature are analyzed for each engine design.

Belair, Michael L.↗

NASA NTRS2013

Nuclear Thermal Rocket Simulation in NPSS

Four nuclear thermal rocket (NTR) models have been created in the Numerical Propulsion System Simulation (NPSS) framework. The models are divided into two categories. One set is based upon the ZrC-graphite composite fuel element and tie tube-style reactor developed during the Nuclear Engine for Rocket Vehicle Application (NERVA) project in the late 1960s and early 1970s. The other reactor set is based upon a W-UO2 ceramic-metallic (CERMET) fuel element. Within each category, a small and a large thrust engine are modeled. The small engine models utilize RL-10 turbomachinery performance maps and have a thrust of approximately 33.4 kN (7,500 lbf ). The large engine models utilize scaled RL-60 turbomachinery performance maps and have a thrust of approximately 111.2 kN (25,000 lbf ). Power deposition profiles for each reactor were obtained from a detailed Monte Carlo N-Particle (MCNP5) model of the reactor cores. Performance factors such as thermodynamic state points, thrust, specific impulse, reactor power level, and maximum fuel temperature are analyzed for each engine design.

Belair, Michael L.↗

NASA NTRS2013

Wind Turbine Contingency Control Through Generator De-Rating

Maximizing turbine up-time and reducing maintenance costs are key technology drivers for wind turbine operators. Components within wind turbines are subject to considerable stresses due to unpredictable environmental conditions resulting from rapidly changing local dynamics. In that context, systems health management has the aim to assess the state-of-health of components within a wind turbine, to estimate remaining life, and to aid in autonomous decision-making to minimize damage to the turbine. Advanced contingency control is one way to enable autonomous decision-making by providing the mechanism to enable safe and efficient turbine operation. The work reported herein explores the integration of condition monitoring of wind turbines with contingency control to balance the trade-offs between maintaining system health and energy capture. The contingency control involves de-rating the generator operating point to achieve reduced loads on the wind turbine. Results are demonstrated using a high fidelity simulator of a utility-scale wind turbine.

condition monitoring↗

NASA NTRSDate not supplied

An Updated Secondary Lunar Meteoroid Ejecta Model for Engineering Design

Introduction: The surface of the Moon is constantly being bombarded by a flux of meteoroids of various sizes. Impacts due to these meteoroids produce secondary ejecta material at much lower speeds but with a total mass larger than the original impactor. Details about the secondary ejecta are important for planning missions on the lunar surface. In this work, an updated ejecta model is presented called the Meteoroid Model of Secondary Ejecta (MeMoSeE), to re-place the Apollo-era ejecta model, NASA SP-8013 [1], in the SLS-SPEC 159 Design Specification for Natural Environments (DSNE) [2]. The model pro-duces secondary ejecta flux environments for a user-specified location on the lunar surface, and sorts the incoming secondary flux by angular direction and speed. Methods: MeMoSeE is separated into three parts: the inputs, the conversion step, and the integration of fluxes. Inputs to the model include the primary meteoroid fluxes and the primary near-Earth object (NEO) fluxes. Meteoroid fluxes, both asteroidal and cometary, are calculated using the Meteoroid Engineering Model (MEM3) [3] for different locations on the Moon. For each surface location, an ephemeris is generated using the JPL HORIZONS System [4] that feeds into MEM3. The NEO fluxes are approximated by the high-density population of MEM3 (i.e., only the directionality), where the speed distribution of the NEO fluxes is renormalized to match observations [5]. The regolith properties are used as defined in the DSNE [2]. The conversion step utilizes scaling laws given by Housen & Holsapple 2011 [6] to convert the primary impactor flux to the total mass of secondary ejecta. The ejecta distribution, at the point-of-impact (POI), is separated into a zenith angle and azimuthal angle distribution. The zenith angle distribution follows a beta distribution where the peak depends on the impact altitude angle and the impact azimuth [7]. We employ an ejecta azimuth distribution that is based on Rival & Mandeville 1999 [8] which focuses ejecta in the downstream direction for more oblique impacts. Finally, during the integration step, we sum secondary ejecta number fluxes at a particular region-of-interest (ROI) that originated from many POI locations over the entire surface of the Moon. We keep track of both altitude and azimuth angle bins as well as a range of speed bins, following the igloo gridding as done in MEM3 [9]. The ejecta particle size distribution and density is assumed to be the same as the lunar regolith [10, 2]. Results: The primary fluxes are computed for one Metonic cycle (19 years) for various locations over the lunar surface with a fixed orientation. Both the angular and speed distributions of the primary fluxes are dependent on the latitude and longitude. The over-all primary fluxes show a roughly 13% increase from the eastern limb to the western limb. In general, the speed distribution of the secondary fluxes span from a user-defined minimum speed to the escape speed of the Moon (2.38 km/s), roughly following a power-law relation [6]. Different parts of the speed distribution come from different primary impact locations on the Moon. The secondary ejecta is dominated by the slowest speeds, where these particles originate nearby the ROI. For speeds around 71% of the escape speed, the secondary ejecta originates from locations near the antipodal point. On the other hand, for secondary ejecta speeds that exceed roughly 90% the escape speed, the ejecta particles come from all over the lunar surface to the ROI. Comparing the secondary ejecta fluxes from MeMoSeE with NASA SP-8013 [1], there is a reduction by about 2-3 orders of magnitude for secondary ejecta particles greater than 1 µg. These estimates agree with recent findings from Bjorkman & Christiansen 2019 [11]. The secondary ejecta fluxes are also compared with the primary fluxes, where the ejecta fluxes are roughly an order of magnitude greater than the primary fluxes. References: [1] Cour-Palais, B. G., (1969) NASA SP-8013. [2] NASA SLS-SPEC-159 Rev. H (2020). [3] Moorhead, A. V., et al. (2019) JS&R, 1-17. [4] Giorgini, J. D., (2015) IAUGA, 29, 2256293. [5] Moorhead, A. V., (2020) Memo OSMA/MEO/Lunar-001. [6] Housen, K. R., and Holsapple, K. A., (2011) Icarus, 211(1), 856-875. [7] Gault, D. E., and Wedekind, J. A., (1978) L&PSCP, 9, 3843-3875. [8] Rival, M., and Mandeville, J., (1999) Space Debris, 1(1), 45-57. [9] Moorhead, A. V., (2019) MEM3 User Guide. [10] Carrier, W. D., (1973) The Moon, 6(3-4), 250-263. [11] Bjorkman, M. D. & Christiansen, E. L., (2019) ODC

impacts↗

NASA NTRSDate not supplied

Scaling Climbing Collaborative Mobile Manipulators (C2M2) for Outfitting a Tall Lunar Tower (TLT) and Truss Structures

In-space and planetary truss structures like the Tall Lunar Tower (TLT) can greatly benefit from truss climbing collaborative mobile manipulators (C-CMMs) for outfitting and other servicing tasks. Mobile robotic systems traversing these structures will allow for improved access to the structure for placing equipment and routing cables after the structure has been assembled. The robotic system described in the proposed paper is designed to provide access to the structure through collaborative mobile robotics. The paper will provide a method to constrain the design of such a robot via the geometry of the truss structure and the controlling joint torques across various gaits. The focus of the design is on a six-degree of freedom (DOF) robot arranged with two-DOF at each end and at the center. The variable features of this system are the actuators and the length of the links connecting the two-DOF modules. The result of the analysis is a link sizing range which the robot can be designed within to ensure functionality on the truss structure. A C-CMM will be designed using the scaling utility and several constructed to demonstrate operating both independently and collaboratively.

in-space assembly↗

NASA NTRSDate not supplied

Space Based Solar Power

Space based solar power (SBSP) entails in-space collection of solar energy, transmission of that energy to one or more stations on Earth, conversion to electricity, and delivery to the grid or to batteries for storage. Experts in both the aerospace and energy sectors are debating the benefits of SBSP as more organizations globally begin SBSP technology development programs. We conducted a study to evaluate the potential benefits, challenges, and options for NASA to engage with growing global interest in SBSP. We performed a first order lifecycle study of two representative SBSP designs for 2 GW utility-scale power generation that, for the purposes of the study, are presumed to begin in 2050. We assumed baseline capabilities to develop, assemble, operate, maintain, and dispose of the SBSP systems are a mix of capabilities that are above, below, or comparable to capabilities demonstrated to date. We then compared the lifecycle cost of electricity and lifecycle GHG emission intensity of the SBSP designs to alternative terrestrial renewable electricity production technologies. Our findings indicate the SBSP designs may produce lifecycle GHG emissions per unit of electricity that are comparable to terrestrial alternatives, pending further studies of upper atmosphere responses to launch emissions. We find the SBSP designs are more expensive than terrestrial alternatives and may have lifecycle costs per unit of electricity that are 12-80 times higher. Though, we do find cost competitiveness may be achieved if a favorable combination of cost and capability improvements related to launch and manufacturing that are beyond the advancements assumed in the baseline assessment can be attained.

Erica Rodgers↗

NASA NTRSDate not supplied

Space Based Solar Power Study

Space based solar power (SBSP) entails in-space collection of solar energy, transmission of that energy to one or more stations on Earth, conversion to electricity, and delivery to the grid or to batteries for storage. Experts in both the aerospace and energy sectors are debating the benefits of SBSP as more organizations globally begin SBSP technology development programs. We conducted a study to evaluate the potential benefits, challenges, and options for NASA to engage with growing global interest in SBSP. We performed a first order lifecycle study of two representative SBSP designs for 2 GW utility-scale power generation that, for the purposes of the study, are presumed to begin in 2050. We assumed baseline capabilities to develop, assemble, operate, maintain, and dispose of the SBSP systems are a mix of capabilities that are above, below, or comparable to capabilities demonstrated to date. We then compared the lifecycle cost of electricity and lifecycle GHG emission intensity of the SBSP designs to alternative terrestrial renewable electricity production technologies. Our findings indicate the SBSP designs may produce lifecycle GHG emissions per unit of electricity that are comparable to terrestrial alternatives, pending further studies of upper atmosphere responses to launch emissions. We find the SBSP designs are more expensive than terrestrial alternatives and may have lifecycle costs per unit of electricity that are 12-80 times higher. Though, we do find cost competitiveness may be achieved if a favorable combination of cost and capability improvements related to launch and manufacturing that are beyond the advancements assumed in the baseline assessment can be attained.

solar↗

DOE OSTI2020

California Time-of-Use (TOU) Transition: Effects on Distributed Wind and Solar Economic Potential

Time-of-use (TOU) retail energy rates price electricity differently by the time of day, communicating to consumers the costs of supplying electricity diurnally. This study evaluates the impact of Decision D.15.07-001, which mandates a transition in 2020 to default TOU rates for residential ratepayers in California, on the economic viability of behind-the-meter distributed wind and solar systems. Previous studies have demonstrated that increasing wind and solar generation will materially affect the diurnal cost of wholesale electricity. As retail and wholesale prices become more aligned, this could affect the inter-technology economic viability of distributed generation. We assess economic viability through 'economic potential,' or the amount of generation capacity that exceeds a rate of return of 5.4%. In addition, we identify sensitivities of economic potential to capital costs and other techno-economic factors as well as the specific counties and sectors with substantial economic potential. We find that TOU implementation is projected to moderately increase economic potential of distributed wind and marginally decrease that of distributed solar. Over the long-term as variable renewable energy penetration increases in California, particularly utility-scale solar, net peak load and thus peak prices will shift later in the evening. To the extent that retail rates continue to evolve with wholesale prices, we find the changes could positively affect the value of wind generation more than that of solar generation. Over the scenarios considered, model results indicate realistic pathways to reaching a robust distributed wind market in California though solar economic potential was found to be substantially larger than that of wind.

17 WIND ENERGY↗

DOE OSTI2020

Provision of Grid Services by PV Plants with Integrated Battery Energy Storage System: Preprint

Battery energy storage systems (BESS), due to their tremendous range of uses and configurations, may assist PV integration in any number of ways by increasing power system flexibility. In this paper we describe results of a research project conducted by NREL and First Solar for developing controls and demonstrating many use cases for PV-BESS systems including (1) matching generation to loads through time shifting, reducing PV curtailment,; (2) promoting higher levels of PV penetrations by balancing the grid through ancillary services; (3) use of PV-BESS systems to provide wide-area stability services in the form of oscillations damping controls; and (r) use of gird forming BESS for enabling black start and islanded applications for PV-BESS systems. In the paper we will also describe the unique multi-MW test and validation platform developed at NREL for conducting research on fielded utility-scale PV-BESS systems. The platform consists of First Solar 0.43 MW PV power plant, NREL’s 1MW/1MW BESS, 2MW PV power supplies and 7MVA power electronic grid simulator interfaced with industrial plant controllers and power-hardware-in-the-loop (PHIL) capability.

41 EE - Solar Energy Technologies Office (EE-4S)↗

DOE OSTI2021

Cadmium Telluride Photovoltaics Accelerator Consortium Solicitation: Request for Proposals Information

Cadmium telluride photovoltaics (CdTe PV) is a leading PV technology built on U.S. innovations that currently holds significant market share within domestic utility scale PV systems. In order to keep pace with a highly competitive and innovative global PV module market, CdTe manufacturing needs readily adaptable advances at the cell and module levels that simultaneously enable higher conversion efficiencies and manufacturing cost reductions without risking long-term module durability. In pursuit of this goal, the Department of Energy (DOE) Solar Energy Technologies Office (SETO) has asked the National Renewable Energy Laboratory (NREL) to launch and support a Consortium to accelerate domestic CdTe technology development through a competitive solicitation process. NREL will competitively select a CdTe Consortium with the goals of enhancing U.S. competitiveness and expanding domestic CdTe PV material and module production through 2030. NREL will provide coordination and oversight through development of technical scopes, review of technical proposals, subcontract support, and review of deliverables along with research support to the Consortium. The new Consortium is expected to include major U.S. companies and universities that possess strong technology development, transfer, and validation capabilities. The research and analysis output of the CdTe Consortium will inform purchasing, design, deployment, and operations decisions of companies in the domestic CdTe PV supply chain, leading to increased material and module production in the U.S.

41 EE - Solar Energy Technologies Office (EE-4S)↗

DOE OSTI2021

A Circularity Assessment for Silicon Solar Panels Based on Dynamic Material Flow Analysis

Solar photovoltaics (PV) are the fastest growing renewable energy technology for clean, inexpensive, and sustainable electricity generation. Along with numerous technical roadmaps to improve system cost, performance and reliability, the PV industry should also plan to handle large volumes of silicon panel waste, which is initially estimated to be ~13 million metric tons (MT) by 2050 in the U.S. alone. Understanding the magnitude of material needs and how material flows throughout the PV panel life cycle could respond to design, operational and different end-of-life (EOL) circular pathways will help transition into a circular, resource-conserving economy. Herein, we introduce a dynamic material flow analysis (DMFA) framework based on electricity generation to quantify time-series stocks and flows of bulk PV materials (e.g., solar glass and aluminum frames) throughout the life cycles of utility-scale silicon PV systems in the U.S. in the period 2000-2100. We apply the model to a range of scenarios to understand how material demands depend on selected PV-related parameters, different material circularity strategies, and recent module design trends (e.g., bifacial, frameless). We found that float glass and aluminum in PV installations would likely reach 100 million MT and 12 million MT by 2100, respectively, in the baseline scenario. The most influential parameters for PV installation and subsequent waste reduction are found to be module lifetime, module efficiency, annual degradation, and material reduction. Module recycling and component remanufacturing were found to be the most effective material circularity strategies for waste minimization. Panel reuse has negligible savings on waste under current module efficiencies compared to replacements with newer generations with higher efficiency. Ongoing trends to produce larger power frameless modules could save 10 million MT of glass and ~9 million MT of aluminum. Our results enable advanced planning for future materials needs and provide insight into potential opportunities to minimize waste.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Storage Futures Study - Distributed Solar and Storage Outlook: Methodology and Scenarios

This presentation discusses the fourth report in NREL’s Storage Futures Study (SFS) publications. The SFS is a multiyear research project that explores the role and impact of energy storage in the evolution and operation of the U.S. power sector. The SFS is designed to examine the potential impact of energy storage technology advancement on the deployment of utility-scale storage and the adoption of distributed storage, and the implications for future power system infrastructure investment and operations. This report describes the expanded capabilities of the Distributed Generation Market Demand (dGen) model to analyze the economics of distributed (behind-the-meter) PV paired with battery storage systems and presents projections of adoption for the contiguous United States out to 2050 under a range of scenarios. These scenarios use technology cost and performance assumptions consistent with the National Renewable Energy Laboratory’s 2020 Standard Scenarios paired with updated battery cost projections and existing policies. Additional scenarios evaluate sensitivities to the value of backup power and DER compensation mechanisms, collectively characterizing the future potential for behind-the-meter storage and identifying key drivers of adoption. Adoption projections of DER and battery storage at high spatial and temporal resolution, as presented in this report, can enable informed planning of technical infrastructure that can help planners capture the benefits and mitigate challenges to support the ongoing trend toward distributed electricity generation.

backup power↗

DOE OSTI2021

Wind Turbine Blade Finishing Automation: Robotic Toolpath Generation

Wind turbine blades are now over 100 meters long and can reach heights of several meters while in the finishing area of the factory. Because of this, automation should be used to lower the manufacturing cost and make the process safer for blade manufacturing technicians. This session will present a novel method that generates a six degree of freedom robotic toolpath with 3D cameras for the finishing of wind turbine blades to drive down the levelized cost and make wind energy even more competitive in the utility scale energy generation industry.

3d imaging↗

DOE OSTI2021

A Circularity Assessment for Silicon Solar Panels Based on Dynamic Material Flow Analysis: Preprint

Solar photovoltaics (PV) are the fastest growing renewable energy technology for clean, inexpensive, and sustainable electricity generation. Along with numerous technical roadmaps to improve system cost, performance and reliability, the PV industry should also plan to handle large volumes of silicon panel waste, which is initially estimated to be ~13 million metric tons (MT) by 2050 in the U.S. alone. Understanding the magnitude of material needs and how material flows throughout the PV panel life cycle could respond to design, operational and different end-of-life (EOL) circular pathways will help transition into a circular, resource-conserving economy. Herein, we introduce a dynamic material flow analysis (DMFA) framework based on electricity generation to quantify time-series stocks and flows of bulk PV materials (e.g., solar glass and aluminum frames) throughout the life cycles of utility-scale silicon PV systems in the U.S. in the period 2000-2100. We apply the model to a range of scenarios to understand how material demands depend on selected PV-related parameters, different material circularity strategies, and recent module design trends (e.g., bifacial, frameless). We found that float glass and aluminum in PV installations would likely reach 100 million MT and 12 million MT by 2100, respectively, in the baseline scenario. The most influential parameters for PV installation and subsequent waste reduction are found to be module lifetime, module efficiency, annual degradation, and material reduction. Module recycling and component remanufacturing were found to be the most effective material circularity strategies for waste minimization. Panel reuse has negligible savings on waste under current module efficiencies compared to replacements with newer generations with higher efficiency. Ongoing trends to produce larger power frameless modules could save 10 million MT of glass and ~9 million MT of aluminum. Our results enable advanced planning for future materials needs and provide insight into potential opportunities to minimize waste.

circular economy↗

DOE OSTI2021

Energy Arbitrage: Comparison of Options for use with LWR Nuclear Power Plants

Arbitrage is the opportunistic buying and selling of a commodity during local pricing valleys and peaks respectively to maximize economic value. This report evaluates options for energy arbitrage integrated with existing light water reactor (LWR) nuclear power plants (NPPs) where nuclear energy could be stored in a variety of forms and later recovered to generate electrical power during periods when grid electricity demand and pricing are high. The forms of energy storage examined in this report include the potential value of batteries, hydrogen, and thermal energy storage for coupling with nuclear power. Various large demand response options are also analyzed, including the production of liquid nitrogen via air separation and liquefaction, liquefaction of hydrogen, compressed hydrogen, and the cryogenic capture of CO2. Demand response refers to dispatchable loads that can cycle up or down depending on-grid electricity demand to aid in balancing the grid. Large demand response options could dispatch to aid nuclear power stations in avoiding power turndowns by providing an alternate disposition for electrical energy by producing marketable products (e.g., liquid nitrogen, hydrogen, or captured CO2). Static conditions were chosen and analyzed in this report for each option. Dynamic operation or optimization of energy arbitrage or demand response are out of scope for this report. The analysis is based on storage systems with discharge capacities of 500 MW for which various durations of storage and costs of charging (electricity cost) are examined. While the value of thermal energy to an industrial user for flexible plant operations has been previously proven as a business case, this report evaluates costs of hydrogen energy storage and leading thermal energy storage options, and large demand response loads that could be integrated with LWRs in comparison to utility-scale battery storage for use of off-peak nuclear energy. Compilation of this information will be used by the Idaho National Laboratory (INL) RAVEN/HERON systems integration and economics tool to evaluate thermal energy dispatch to industrial users. Relative ranking of energy storage options was done using a levelized cost of storage (LCOS) metric which calculates a rough breakeven cost for the system, taking into account the capital and operating costs as well as the revenue from arbitrage. Table ES1 below shows the LCOS for each of the energy storage options considered. First, in the table, lithium iron (Fe) phosphate batteries are listed as the base case for comparison against the other options. Next is hydrogen storage where most of the hydrogen analyses assumed the hydrogen to be produced using solid oxide electrolytic cell (SOEC) high temperature steam electrolysis (HTSE). The others used existing models of polymer electrolyte membrane (PEM) low temperature electrolysis to produce hydrogen. HTSE performance parameters and costs were taken from existing INL models. Various means were assumed to convert the hydrogen to electricity, including PEM fuel cells (FCs) and a gas turbine mixed in a 30 vol% mixture with natural gas. Physical storage (pressure vessels) and geological storage (natural underground features) were used to store the hydrogen as noted. Geological storage is more economical, but the locations are limited because of the requirement for pre-existing geological formations that will support storage. Thermal energy storage (TES) options were also analyzed including electro-thermal energy storage (ETES) and four different liquid sensible heat TES storage media as noted (Hitec, Hitec XL, Therminol-66, and Dowtherm A). The ETES process considered was modified using existing public documentation on an Echogen process and uses a separate supercritical CO2 charge and discharge cycle with sand as the heat storage media.

25 ENERGY STORAGE↗

DOE OSTI2021

Geothermal Energy and Resilience in Arctic Countries

The eight Arctic countries have diverse energy systems but can be split into two distinct groups based on energy characteristics. The first group includes countries which are heavily gridconnected (Iceland, Norway, Sweden, and Finland); the second group includes countries with some grids as well as an abundance of remote microgrids, particularly in their more northern regions (Canada, Russia, the United States [Alaska], and Greenland). The primary energy source for both heat and power in remote communities is almost exclusively diesel. Geothermal energy is currently used in all eight Arctic countries, providing heat and sometimes electricity at utility scales and at the microgrid scale. However, the availability of geothermal resources is poorly defined in Arctic countries. We reframe geothermal heat and power as integrated energy systems, asking the question: are integrated geothermal energy systems - where available and economic - resilient solutions for communities in Arctic countries? Resilience attributes of integrated geothermal energy systems are identified, with a focus on microgrids and small-scale applications.

arctic energy↗

DOE OSTI2022

Storage Futures Study: Key Learnings for the Coming Decades

The Storage Futures Study (SFS) is a multiyear research project that explored the role and impact of energy storage in the evolution and operation of the U.S. power sector. The SFS examined the potential impact of energy storage technology advancement on the deployment of utility-scale storage and the adoption of distributed storage, and the implications for future power system infrastructure investment and operations. The research findings and supporting data were published across a series of six reports, culminating in the final, seventh publication that draws upon findings from across the study, previous work, and additional analysis to identify eight key learnings about the coming decades. This presentation is from an NREL webinar to discuss the eight key learnings.

decarbonization↗