Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “turbulent flows”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
NASA NTRS1955

Free-Stream Boundaries of Turbulent Flows

Report presents the results of an experimental and theoretical study made of the instantaneously sharp and irregular front which is always found to separate turbulent fluid from contiguous "nonturbulent" fluid at a free-stream boundary. This distinct demarcation is known to give an intermittent character to hot-wire signals in the boundary zone. The overall behavior of the front is described statistically in terms of its wrinkle-amplitude growth and its lateral propagation relative to the fluid as functions of downstream coordinate.

Corrsin, Stanley↗
NASA NTRS1980

Wall proximity corrections for hot-wire readings in turbulent flows

This note describes some details of recent (successful) attempts of wall proximity corrections for hot-wire measurements performed in a three-dimensional incompressible turbulent boundary layer. A simple and quite satisfactory method of estimating wall proximity effects on hot-wire readings is suggested.

Hebbar, K. S.↗
NASA NTRS2002

Measurements of Turbulent Flow Field in Separate Flow Nozzles with Enhanced Mixing Devices - Test Report

As part of the Advanced Subsonic Technology Program, a series of experiments was conducted at NASA Glenn Research Center on the effect of mixing enhancement devices on the aeroacoustic performance of separate flow nozzles. Initial acoustic evaluations of the devices showed that they reduced jet noise significantly, while creating very little thrust loss. The explanation for the improvement required that turbulence measurements, namely single point mean and RMS statistics and two-point spatial correlations, be made to determine the change in the turbulence caused by the mixing enhancement devices that lead to the noise reduction. These measurements were made in the summer of 2000 in a test program called Separate Nozzle Flow Test 2000 (SFNT2K) supported by the Aeropropulsion Research Program at NASA Glenn Research Center. Given the hot high-speed flows representative of a contemporary bypass ratio 5 turbofan engine, unsteady flow field measurements required the use of an optical measurement method. To achieve the spatial correlations, the Particle Image Velocimetry technique was employed, acquiring high-density velocity maps of the flows from which the required statistics could be derived. This was the first successful use of this technique for such flows, and shows the utility of this technique for future experimental programs. The extensive statistics obtained were likewise unique and give great insight into the turbulence which produces noise and how the turbulence can be modified to reduce jet noise.

Bridges, James↗
NASA NTRS1953

Analogy Between Mass and Heat Transfer with Turbulent Flow

An analysis of combined heat and mass transfer from a flat plate has been made in terms of Prandtl t s simplified physical concept of the turbulent boundary layer. The results of the analysis show that for conditions of reasonably small heat and mass transfer, the ratio of the mass-and heat-transfer coefficients is dependent on the Reynolds number of the boundary layer, the Prandtl number of the medium of diffusion, and the Schmidt number of the diffusing fluid in the medium of diffusion. For the particular case of water evaporating into air, the ratio of mass-transfer coefficient to heat-transfer coefficient is found to be slightly greater than unity.

Callaghan, Edmund E.↗
NASA NTRS1987

Development of Large-Eddy Interaction Model for inhomogeneous turbulent flows

The objective of this paper is to demonstrate the applicability of a currently proposed model, with minimum empiricism, for calculation of the Reynolds stresses and other turbulence structural quantities in a channel. The current Large-Eddy Interaction Model not only yields Reynolds stresses but also presents an opportunity to illuminate typical characteristic motions of large-scale turbulence and the phenomenological aspects of engineering models for two Reynolds numbers.

Hong, S. K.↗
NASA NTRS2001

Disturbance Dynamics in Transitional and Turbulent Flows

The dynamics of an ensemble of linear disturbances with a known probability distribution associated with the initial mode amplitudes are studied in boundary-layer flows through an analysis of the transport equations for the mean disturbance kinetic energy and disturbance energy dissipation rate. Effects of adverse and favorable pressure-gradients on the disturbance dynamics are also included in the analysis. Unlike the fully turbulent regime where nonlinear phase scrambling of the fluctuations affects the flow field in proximity to the wall, the laminar regime fluctuations studied here are influenced across the boundary layer by the solid boundary. In addition to the low Reynolds number, early stage transition regime, the dynamics of these disturbance fields can be related in some respects to the near-wall dynamics of the fully turbulent regime.

Grosch, C. E.↗
NASA NTRS1991

Computation of turbulent flow in a thin liquid layer of fluid involving a hydraulic jump

Numerically computed flow fields and free surface height distributions are presented for the flow of a thin layer of liquid adjacent to a solid horizontal surface that encounters a hydraulic jump. Two kinds of flow configurations are considered: two-dimensional plane flow and axisymmetric radial flow. The computations used a boundary-fitted moving grid method with a k-epsilon model for the closure of turbulence. The free surface height was determined by an optimization procedure which minimized the error in the pressure distribution on the free surface. It was also checked against an approximate procedure involving integration of the governing equations and use of the MacCormack predictor-corrector method. The computed film height also compared reasonably well with previous experiments. A region of recirculating flow was found to be present adjacent to the solid boundary near the location of the jump, which was caused by a rapid deceleration of the flow.

Rahman, M. M.↗
NASA NTRS1992

Assessment of closure coefficients for compressible-flow turbulence models

A critical assessment is made of the closure coefficients used for turbulence length scale in existing models of the transport equation, with reference to the extension of these models to compressible flow. It is shown that to satisfy the compressible 'law of the wall', the model coefficients must actually be functions of density gradients. The magnitude of the errors that result from neglecting this dependence on density varies with the variable used to specify the length scale. Among the models investigated, the k-omega model yields the best performance, although it is not completely free from errors associated with density terms. Models designed to reduce the density-gradient effect to an insignificant level are proposed.

Huang, P. G.↗
DOE OSTI2022

A Large Eddy Simulation Study of Flow Turbulence, Alumina Transport, and Bath Temperature Evolution in Conventional Aluminum-Smelting Cell Using OpenFOAM

In this study, a Large Eddy Simulation (LES) of the aluminum-smelting process is performed using OpenFOAM. To understand the coupled behavior of heat transfer, mass transfer, and flow of the smelting process, a multi-physics computational fluid dynamics (CFD) model based on the Eulerian–Eulerian multi-fluid approach is adopted. The model accounts for CO 2 bubble and magnetohydrodynamics (MHD)-driven flow, along with alumina dissolution, transport, and bath temperature evolution. The simulation predictions show small-scale turbulent vortical structures in the anode–cathode space caused by combined effect of MHD and CO 2 bubble-bath interactions and relatively large-scale asymmetric vortices in the inter-anode space caused by the CO 2 bubble-bath interactions. The vortex formation at the edges of the anodes evidently aids in transporting alumina from the central channel to the bottom of the anodes and prevents accumulation of gas bubbles in the periphery of the anode bottom. Symmetric bath cold spots are observed in the vicinity of the feeder. Cold spots are also observed in the anode–cathode distance space below the anode bottom due to the transport of undissolved solid to this region by the flow. The findings from the work are useful in developing and designing alumina-feeding strategy leading to reduced anode effects and smooth operation of the cell. The work also highlights the important flow structures in conventional aluminum-smelting cell.

36 MATERIALS SCIENCE↗
NASA NTRS1991

Near-wall modeling of compressible turbulent flow

A near-wall two-equation model for compressible flows is proposed. The model is formulated by relaxing the assumption of dynamic field similarity between compressible and incompressible flows. A postulate is made to justify the extension of incompressible models to ammount for compressibility effects. This requires formulation the turbulent kinetic energy equation in a form similar to its incompressible counterpart. As a result, the compressible dissipation function has to be split into a solenoidal part, which is not sensitive to changes of compressibility indicators, and a dilatational part, which is directly affected by these changes. A model with an explicit dependence on the turbulent Mach number is proposed for the dilatational dissipation rate.

So, Ronald M. C.↗
NASA NTRS1994

Three Dimensional Compressible Turbulent Flow Computations for a Diffusing S-Duct With/Without Vortex Generators

Numerical investigations on a diffusing S-duct with/without vortex generators and a straight duct with vortex generators are presented. The investigation consists of solving the full three-dimensional unsteady compressible mass averaged Navier-Stokes equations. An implicit finite volume lower-upper time marching code (RPLUS3D) has been employed and modified. A three-dimensional Baldwin-Lomax turbulence model has been modified in conjunction with the flow physics. A model for the analysis of vortex generators in a fully viscous subsonic internal flow is evaluated. A vortical structure for modeling the shed vortex is used as a source term in the computation domain. The injected vortex paths in the straight duct are compared with the analysis by two kinds of prediction models. The flow structure by the vortex generators are investigated along the duct. Computed results of the flow in a circular diffusing S-duct provide an understanding of the flow structure within a typical engine inlet system. These are compared with the experimental wall static-pressure, static- and total-pressure field, and secondary velocity profiles. Additionally, boundary layer thickness, skin friction values, and velocity profiles in wall coordinates are presented. In order to investigate the effect of vortex generators, various vortex strengths are examined in this study. The total-pressure recovery and distortion coefficients are obtained at the exit of the S-duct. The numerical results clearly depict the interaction between the low velocity flow by the flow separation and the injected vortices.

Cho, Soo-Yong↗
DOE OSTI2020

Extracting a mixing parameter from 2D radiographic imaging of variable-density turbulent flow

We extract a suitably averaged fluctuating density from the two-dimensional radiographic image of a flow. The X-ray attenuation is given by the Beer–Lambert law which exponentially damps the incident beam intensity by a factor proportional to the density, opacity and thickness of the target. By making reasonable assumptions for the mean density, opacity and effective thickness of the target flow, we estimate the density fluctuation contribution to the attenuation. The extracted density fluctuations averaged across the thickness of the flow in the direction of the beam may be used to form the density–specific-volume correlation $b$. In a statistical description of variable-density turbulence, $b$ quantifies the degree of mixedness. The ability to extract a measure of mixedness from experimental data would be a powerful tool that could be used in the validation of mix models. The scheme proposed is tested for DNS data computed for variable density buoyancy-driven mixing. We quantify the deficits in the extracted value of $b$ due to target thickness, Atwood number and modeled signal noise. This analysis justifies using the proposed scheme to infer the mix parameter from thin targets at moderate to low Atwood numbers. Furthermore, to illustrate how the scheme might be used in a practical problem, we demonstrate its application to a radiographic image of counter-shear flow obtained from experiments at the National Ignition Facility.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

Direct Numerical Simulation of Transitional and Turbulent Flows Over Multi-Scale Surface Roughness—Part II: The Effect of Roughness on the Performance of a High-Pressure Turbine Blade

Abstract Turbine blades generally present surface roughness introduced in the manufacturing process or caused by in-service degradation, which can have a significant impact on aero-thermal performance. A better understanding of the fundamental physical mechanisms arising from the interaction between the roughness and the turbine flow at engine-relevant conditions can provide insights for the design of blades with improved efficiency and longer operational life. To this end, a high-fidelity numerical framework combining a well-validated solver for direct numerical simulation and a second-order accurate immersed boundary method is employed to predict roughness-induced aero-thermal effects on an LS89 high-pressure turbine (HPT) blade at engine-relevant conditions. Different amplitudes and distributions of surface roughness are investigated and a reference smooth-blade simulation under the same flow conditions is conducted for comparison. Roughness of increasing amplitude progressively shifts the blade suction side boundary layer transition upstream, producing larger values of the turbulent kinetic energy and higher total wake losses. The on-surface data-capturing capabilities of the numerical framework provide direct measurements of the heat flux and the skin friction coefficient, hence offering quantitative information between the surface topology and engineering-relevant performance parameters. This work may provide a benchmark for future numerical studies of turbomachinery flows with roughness.

Engineering↗
NASA NTRS1990

One- and two-dimensional Stirling machine simulation using experimentally generated flow turbulence models

Investigations of one- and two-dimensional (1- or 2-D) simulations of Stirling machines centered around experimental data generated by the U. of Minnesota Mechanical Engineering Test Rig (METR) are covered. This rig was used to investigate oscillating flows about a zero mean with emphasis on laminar/turbulent flow transitions in tubes. The Space Power Demonstrator Engine (SPDE) and in particular, its heater, were the subjects of the simulations. The heater was treated as a 1- or 2-D entity in an otherwise 1-D system. The 2-D flow effects impacted the transient flow predictions in the heater itself but did not have a major impact on overall system performance. Information propagation effects may be a significant issue in the simulation (if not the performance) of high-frequency, high-pressure Stirling machines. This was investigated further by comparing a simulation against an experimentally validated analytic solution for the fluid dynamics of a transmission line. The applicability of the pressure-linking algorithm for compressible flows may be limited by characteristic number (defined as flow path information traverses per cycle); this warrants further study. Lastly the METR was simulated in 1- and 2-D. A two-parameter k-w foldback function turbulence model was developed and tested against a limited set of METR experimental data.

Goldberg, Louis F.↗
NASA NTRS1991

The dissipation-range spectrum and the velocity-derivative skewness in turbulent flows

A dynamical equation for the energy dissipation rate is used together with a model spectrum to predict the velocity derivative skewness at a high Reynolds number. The objective is to determine the best choice of the exponent, m, so that the resulting model spectrum can be used to estimate statistical properties of the fine scales of turbulence. Skewness data suggest that m = 2 is the best model for laboratory-scale flows and m = 1 is a poor model for a broad range of Reynolds numbers.

Smith, L. M.↗
NASA NTRS1994

A New K-epsilon Eddy Viscosity Model for High Reynolds Number Turbulent Flows: Model Development and Validation

A new k-epsilon eddy viscosity model, which consists of a new model dissipation rate equation and a new realizable eddy viscosity formulation, is proposed. The new model dissipation rate equation is based on the dynamic equation of the mean-square vorticity fluctuation at large turbulent Reynolds number. The new eddy viscosity formulation is based on the realizability constraints: the positivity of normal Reynolds stresses and Schwarz' inequality for turbulent shear stresses. We find that the present model with a set of unified model coefficients can perform well for a variety of flows. The flows that are examined include: (1) rotating homogeneous shear flows; (2) boundary-free shear flows including a mixing layer, planar and round jets; (3) a channel flow, and flat plate boundary layers with and without a pressure gradient; and (4) backward facing step separated flows. The model predictions are compared with available experimental data. The results from the standard k-epsilon eddy viscosity model are also included for comparison. It is shown that the present model is a significant improvement over the standard k-epsilon eddy viscosity model.

Shih, T.-H.↗
NASA NTRS1984

Numerical modeling of turbulent flow

Three dimensional combustor calculations are currently stretching the computer hardware capabilities and the computing budgets of gas turbine manufacturers. One of the main reasons for this relates to the large number of complex physical processes occurring in the combustor. Airflow, fuel spray, reaction kinetics, flame radiation, and not the least of which, turbulence must be modeled and the related differential equations solved. Discussions in this conference will address methods to improve the accuracy of combustor flow field calculations and methods to speed the convergence of the modeled equations. This report will focus on aspects of merging these two new technologies. The improved accuracy discretization schemes have a negative impact on the speed of convergence of the modeled equations that the improved solution algorithms may not overcome. A description of the causes of this problem and potential solutions will be examined.

Claus, R. W.↗