Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “temperature acceleration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

Helium pressures in RHIC vacuum cryostats and relief valve requirements from magnet cooling line failure

A catastrophic failure of the RHIC magnet cooling lines, similar to the LHC superconducting bus failure incident, would pressurize the insulating vacuum in the magnet and transfer line cryostats. Insufficient relief valves on the cryostats could cause a structural failure. A SINDA/FLUINT{reg_sign} model, which simulated the 4.5K/4 atm helium flowing through the magnet cooling system distribution lines, then through a line break into the vacuum cryostat and discharging via the reliefs into the RHIC tunnel, had been developed to calculate the helium pressure inside the cryostat. Arc flash energy deposition and heat load from the ambient temperature cryostat surfaces were included in the simulations. Three typical areas: the sextant arc, the Triplet/DX/D0 magnets, and the injection area, had been analyzed. Existing relief valve sizes were reviewed to make sure that the maximum stresses, caused by the calculated maximum pressures inside the cryostats, did not exceed the allowable stresses, based on the ASME Code B31.3 and ANSYS results. The conclusions are as follows: (1) The S/F simulation results show that the highest internal pressure in the cryostats, due to the magnet line failure, is {approx}37 psig (255115 Pa); (2) Based on the simulation, the temperature on the cryostat chamber, INJ Q8-Q9, could drop to 228 K, which is lower than the material minimum design temperature allowed by the Code; (3) Based on the ASME Code and ANSYS results, the reliefs on all the cryostats inside the RHIC tunnel are adequate to protect the vacuum chambers when the magnet cooling lines fail; and (4) In addition to the pressure loading, the thermal deformations, due to the temperature decrease on the cryostat chambers, could also cause a high stress on the chamber, if not properly supported.

43 PARTICLE ACCELERATORS↗

Evidence for particle acceleration in AE Aqr from radio and X-ray observations

The novalike cataclysmic variable AE Aquarii shows evidence for radio synchrotron emission from expanding magnetized clouds. The radio and UV flare timescales are similar indicating that the central engine is located close to the white dwarf. A collisionless shock may develop above the polar cap, which may explain the observed temperature. Protons and ions accelerated up to energies of more than 1 TeV can diffuse away from the central engine, enter magnetized clouds, and generate waves which in turn heat and accelerate electrons. An embarrassing situation exists where reprocessed optical and X-ray pulsations (33 s) are observed, but the expected direct X-ray pulse from the white dwarf is absent. The standard theory for CVs cannot explain this, and one possible explanation is that a beam of relativistic protons and ions from the polar cap may give the observed reprocessed optical to X-rays in a thick target fixed in the system.

De Jager, O. C.↗

Climate Sensitivity of Peatland Methane Emissions Mediated by Seasonal Hydrologic Dynamics

Peatlands are among the largest natural sources of atmospheric methane (CH 4 ) worldwide. Peatland emissions are projected to increase under climate change, as rising temperatures and shifting precipitation accelerate microbial metabolic pathways favorable for CH 4 production. However, how these changing environmental factors will impact peatland emissions over the long term remains unknown. Here, we investigate a novel data set spanning an exceptionally long 11 years to analyze the influence of soil temperature and water table elevation on peatland CH 4 emissions. We show that higher water tables dampen the springtime increases in CH 4 emissions as well as their subsequent decreases during late summer to fall. These results imply that any hydroclimatological changes in northern peatlands that shift seasonal water availability from winter to summer will increase annual CH 4 emissions, even if temperature remains unchanged. Furthermore, advancing hydrological understanding in peatland watersheds will be crucial for improving predictions of CH 4 emissions.

54 ENVIRONMENTAL SCIENCES↗

Experimentally Validated Numerical Models of Non-Isothermal Turbulent Mixing in High Temperature Reactors

In the Very High Temperature Reactor (VHTR), the non-uniform heat generation and flow maldistribution of coolant in the core generates conditions leading into the lower plenum with many jets at different temperatures and velocities. The hope is that the combined flow becomes fully mixed in a short distance so that the fluctuating temperatures in the mixing region do not cause unwanted thermal stresses in the supporting structures. These cyclic thermal stresses can cause degradation of the wall microstructure including crack initiation and growth, ultimately leading to the fatigue failure in the lower plenum, and can be accelerated by the high temperature environment in the VHTR. The focus of this project was to provide experimental data for future validation of computational efforts aimed at capturing the turbulent mixing in the lower plenum. Computational fluid dynamics (CFD) is also used as part of this effort to assess the requirements to model fundamental flows with application to the lower plenum as well at the applied flow conditions that mimic the experimental facilities. These efforts will lay the groundwork for future incorporation of stress analysis as well as fatigue and failure studies for multiple VHTR components. An additional emphasis is placed on reduced order models (ROM) using canonical flows, which will help to balance computational expense and accuracy and enable future work in uncertainty quantification. The flow in the lower plenum is extremely complex with hundreds of cooling jets entering and then being forced to change directions by 90° while navigating through an array of cylindrical support posts. Generating experimental data for such a complicated flow is difficult, not to mention that the computational requirements to generate an adequate temporal and spatial sampling is extremely expensive and time consuming. Therefore, the ultimate focus of this research is a “unit cell” which consists of six jets in the presence of a crossflow, and seven cylindrical support posts. It is scaled to achieve similar ranges of key dimensionless numbers. This serves to mimic flow conditions in different regions of the lower plenum by adjusting velocities, temperatures, and orientations, and represents a compromise between the complexity inside the full-scale application and the ideal conditions of a more fundamental study. In addition to the unit cell experiments and simulations, the complex flows in the VHTR lower plenum are broken down into a number of simplified (in some cases even fundamental) flows, two of which are turbulent jets and flow past cylinders. Each of these are studied, computationally and experimentally for isothermal and non-isothermal conditions. Flows where trusted experimental data is available in the literature (e.g., turbulent free jet), additional experiments are not needed. The result of these efforts is a database of experimental data and multiple computational studies, which provide an outlook to the requirements, needed to capture turbulent mixing flow physics The ROM results provide assessments for appropriate resource-light models that balance accuracy with reduced computational burdens.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Accelerated aging of all-inorganic, interface-stabilized perovskite solar cells

To understand degradation routes and improve the stability of perovskite solar cells (PSCs), accelerated aging tests are needed. Here, we use elevated temperatures (up to 110°C) to quantify the accelerated degradation of encapsulated CsPbI 3 PSCs under constant illumination. Incorporating a two-dimensional (2D) Cs 2 PbI 2 Cl 2 capping layer between the perovskite active layer and hole-transport layer stabilizes the interface while increasing power conversion efficiency of the all-inorganic PSCs from 14.9 to 17.4%. Devices with this 2D capping layer did not degrade at 35°C and required >2100 hours at 110°C under constant illumination to degrade by 20% of their initial efficiency. Degradation acceleration factors based on the observed Arrhenius temperature dependence predict intrinsic lifetimes of 51,000 ± 7000 hours (>5 years) operating continuously at 35°C.

Science & Technology - Other Topics↗

Effect of Low Temperature Nitrogen Baking on Superconducting Radio Frequency Cavities With Different Frequency

We report the rf performance of several single-cell superconducting radiofrequency cavities frequency ranging from 1.3-3.0 GHz after low temperature baking in nitrogen environment The cavities are treated at different temperature in the range of (120-160oC) for extended period of time (~24-48 hours) with nitrogen gas injection in the furnace. The improvement in Q0 with Q-rise in some case was observed when nitrogen gas was injected at elevated temperature (~250-290 oC) and held at the temperature range 120-200 oC without any degradation in accelerating gradient over the baseline performance. The temperature and time of baking play significant role in dependence of quality factor on accelerating gradient.

Khanal, B.↗

Low temperature amorphization and superconductivity in FeSe single crystals at high pressures

In this study, we report low temperature x-ray diffraction studies combined with electrical resistance measurements on single crystals of iron-based layered superconductor FeSe to a temperature of 10 K and a pressure of 44 GPa. The low temperature high pressure x-ray diffraction studies were performed using a synchrotron source and superconductivity at high pressure was studied using designer diamond anvils. At ambient temperature, the FeSe sample shows a phase transformation from a PbO-type tetragonal phase to a NiAs-type hexagonal phase at 10 {+-} 2 GPa. On cooling, a structural distortion from a PbO-type tetragonal phase to an orthorhombic Cmma phase is observed below 100 K. At a low temperature of 10 K, compression of the orthorhombic Cmma phase results in a gradual transformation to an amorphous phase above 15 GPa. The transformation to the amorphous phase is completed by 40 GPa at 10 K. A loss of superconductivity is observed in the amorphous phase and a dramatic change in the temperature behavior of electrical resistance indicates formation of a semiconducting state at high pressures and low temperatures. The formation of the amorphous phase is attributed to a kinetic hindrance to the growth of a hexagonal NiAs phase under high pressures and low temperatures.

43 PARTICLE ACCELERATORS↗

Probing the deep nonlinear stage of the ablative Rayleigh-Taylor instability in indirect drive experiments on the National Ignition Facility

Academic tests in physical regimes not encountered in Inertial Confinement Fusion will help to build a better understanding of hydrodynamic instabilities and constitute the scientifically grounded validation complementary to fully integrated experiments. Under the National Ignition Facility (NIF) Discovery Science program, recent indirect drive experiments have been carried out to study the ablative Rayleigh-Taylor Instability (RTI) in transition from weakly nonlinear to highly nonlinear regime [A. Casner et al., Phys. Plasmas 19, 082708 (2012)]. In these experiments, a modulated package is accelerated by a 175 eV radiative temperature plateau created by a room temperature gas-filled platform irradiated by 60 NIF laser beams. The unique capabilities of the NIF are harnessed to accelerate this planar sample over much larger distances (≃1.4 mm) and longer time periods (≃12 ns) than previously achieved. This extended acceleration could eventually allow entering into a turbulent-like regime not precluded by the theory for the RTI at the ablation front. Simultaneous measurements of the foil trajectory and the subsequent RTI growth are performed and compared with radiative hydrodynamics simulations. We present RTI growth measurements for two-dimensional single-mode and broadband multimode modulations. The dependence of RTI growth on initial conditions and ablative stabilization is emphasized, and we demonstrate for the first time in indirect-drive a bubble-competition, bubble-merger regime for the RTI at ablation front.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Operation Regime Analysis of Conduction Cooled Cavities through Multi-Physics Simulation

Euclid Techlabs in collaboration with Fermilab IARC (Batavia, IL) is developing industrial superconducting 10MeV electron linac [1, 2]. Cryocoolers are to be used for cooling instead of liquid helium bath to simplify the linac infrastructure [3]. The cavity linked to commercially available cryo-cooler cold head [4, 5] through highly conductive aluminium (AL) strips. However, this solution raises a problem of contact thermal resistance. This paper shows some results of Comsol multyphysics simulations of the cavity cooling by AL strips. Some insight was obtained on the acceptable range of contact resistance. Operation regimes were obtained at different accelerating gradients and cavity temperatures. The results of simula-tion are presented and discussed.

43 PARTICLE ACCELERATORS↗

Characterization of microstructure and tempering response of conventionally quenched, short- and long-time sub-zero treated PM Vanadis 6 ledeburitic tool steel

Highlights: • Sub-zero treatment refines the microstructural features of Vanadis 6 steel. • Sub-zero treatments foster the precipitation of M{sub 3}C carbides at low temperatures • Transformation of retained austenite is accelerated due to sub-zero treatment. • Elevated hardness of sub-zero treated steel is preserved up to a temperature of 500 °C. • Tempering above 500 °C reduces hardness more significantly due to sub-zero treatment. - Abstract: The microstructure and tempering response of ledeburitic steel Vanadis 6 subjected to sub-zero treatments at a boiling temperature of liquid nitrogen for 4 and 17 h have been examined with reference to conventional heat treatment. The obtained results infer that i) sub-zero treatment induces time-dependent reduction of retained austenite amount, ii) the steel contains considerably enhanced population density of small globular carbides after sub-zero treatments; the population density is directly proportioned to the duration of sub-zero treatment, iii) application of sub-zero treatment results in overall refinement of the microstructure, iv) decomposition of retained austenite is accelerated by sub-zero treatments, v) tempering treatment reduces the population density of small globular carbides, vi) sub-zero treatments modify the precipitation behaviour of carbides; the precipitation of transient M{sub 3}C is accelerated within the low-temperature tempering range, but the precipitation of stable M{sub 7}C{sub 3} carbides is rather suppressed within the normal secondary hardening temperature range, viii) the application of sub-zero treatment leads to complete loss of secondary hardening peak, ix) the overall tempering response of the Vanadis 6 steel is a result of competition between the tempering of the martensite, decomposition of the retained austenite, variations in the small globular carbides count, and precipitation of carbides; higher hardness of sub-zero treated and low-temperature tempered steel can be attributed to lower retained austenite amount, and much higher number of small globular carbides while the loss of secondary hardening peak is explained by much lower contribution of secondary martensitic transformation, suppressed precipitation of special alloy carbides, and reduced number of small globular carbides.

36 MATERIALS SCIENCE↗

Evaluation of Oxygen Consumption as a Sensitive Measure of Electrical Cable Polymer Insulation Degradation

Polymers used as dielectric materials in nuclear grade electrical cables, such as cross-linked polyethylene (XLPE) and ethylene-propylene rubber (EPR), are long-lived and durable. Estimating the decades-long useful service life of polymers experimentally in a feasible timeframe of weeks or months requires greatly accelerated aging in the laboratory at elevated temperatures and/or gamma dose rates. Many limitations of accelerated aging, such as due to artefacts of the process including diffusion limited oxidation and dose rate effects, have been identified that can make accurate lifetime prediction at service conditions challenging. This can be due to differences in degradation mechanisms between rapid and extended aging or to the presence of induction periods during which early aging is undetectable using common metrics of polymer insulation characterization such as tensile elongation at break. Conceptually, an ideal measure of aging would track clearly and predictably with material changes throughout the lifecycle of the evolving material state from early aging through end of useful life. With such a metric accelerated aging could be performed at much milder conditions, conditions closer to those found in long term service, and end of life calculated from the early data. Oxygen consumption has previously been proposed as a sensitive measure of insulation polymer oxidation that might meet such desirable characteristics. In this work, nuclear cable insulation samples of the two most common types, XLPE and EPR, from two of the most sourced manufacturers, RSCC and The Okonite Company, were subjected to gamma irradiation at dose rates of 100, 200, and 300 Gy/hr for up to 42 days at 26°C. The aged samples were used to evaluate oxygen consumption as a sensitive measure of aging for these materials and these conditions. For comparison and validation, the aged samples were also characterized using the more conventional tests of mass change, density, carbonyl index, and yellowness index. For both materials, oxygen consumption during irradiation was found to track consistently with applied dose—oxygen consumption rate was linear with time. Mass change and carbonyl index were also clearly proportional to exposure dose. Yellowness index, a surface sensitive measure, was observed to increase linearly with dose at low exposure levels before plateauing. Sample density was not observed to change under the conditions explored. Oxygen consumption was found to be a particularly sensitive metric to measure the degradation of polymeric cable insulation exposed to radiation. Oxygen consumption was compared to Arrhenius and time-temperature-superposition methods for activation energy calculation using literature date and found to be a useful and viable alternative for lifetime prediction. The techniques developed in this work are anticipated to be valuable in the estimation of insulation aging rates under mild conditions approaching service conditions. Direction comparison of useful life prediction by oxygen consumption with prediction via Arrhenius methodology for thermal aging and existing methods for radiation and combined thermal/radiation aging would serve to further validate this promising approach and refine our understanding of material-specific aging rates.

36 MATERIALS SCIENCE↗

Reactor for simulation and acceleration of solar ultraviolet damage

An environmental test chamber providing acceleration of UV radiation and precise temperature control (+ or -)1 C was designed, constructed and tested. This chamber allows acceleration of solar ultraviolet up to 30 suns while maintaining temperature of the absorbing surface at 30 C - 60 C. This test chamber utilizes a filtered medium pressure mercury arc as the source of radiation, and a combination of selenium radiometer and silicon radiometer to monitor solar ultraviolet (295-340 nm) and total radiant power output, respectively. Details of design and construction and operational procedures are presented along with typical test data.

Laue, E.↗

R&D ERL: HTS Solenoid

An innovative feature of the ERL project is the use of a solenoid made with High Temperature Superconductor (HTS) with the Superconducting RF cavity. The HTS solenoid design offers many advantages because of several unique design features. Typically the solenoid is placed outside the cryostat which means that the beam gets significantly defused before a focusing element starts. In the current design, the solenoid is placed inside the cryostat which provides an early focusing structure and thus a significant reduction in the emittance of the electron beam. In addition, taking full advantage of the high critical temperature of HTS, the solenoid has been designed to reach the required field at {approx}77 K, which can be obtained with liquid nitrogen. This significantly reduces the cost of testing and allows a variety of critical pre-tests which would have been prohibitively expensive at 4 K in liquid helium because of the additional requirements of cryostat and associated facilities.

43 PARTICLE ACCELERATORS↗

Core materials development for the fuel cycle R&D program

The Fuel Cycle Research and Development program is investigating methods of burning minor actinides in a transmutation fuel. One of the challenges of achieving this goal is to develop fuels capable of reaching extreme burnup levels (e.g. 40%). To achieve such high burnup levels fast reactor core materials (cladding and duct) must be able to withstand very high doses (>300 dpa design goal) while in contact with the coolant and the fuel. Thus, these materials must withstand radiation effects that promote low temperature embrittlement, radiation induced segregation, high temperature helium embrittlement, swelling, accelerated creep, corrosion with the coolant, and chemical interaction with the fuel (FCCI). To develop and qualify materials to a total fluence greater than 200 dpa requires development of advanced alloys and irradiations in fast reactors to test these alloys. Test specimens of ferritic/martensitic alloys (T91/HT-9) previously irradiated in the FFTF reactor up to 210 dpa at a temperature range of 350 750 C are presently being tested. This includes analysis of a duct made of HT-9 after irradiation to a total dose of 155 dpa at temperatures from 370 to 510 C. Compact tension, charpy and tensile specimens have been machined from this duct and mechanical testing as well as SANS and Mossbauer spectroscopy are currently being performed. Initial results from compression testing and Charpy testing reveal a strong increase in yield stress (400 MPa) and a large increase in DBTT (up to 230 C) for specimens irradiated at 383 C to a dose of 28 dpa. Less hardening and a smaller increase in DBTT was observed for specimens irradiated at higher temperatures up to 500 C. Advanced radiation tolerant materials are also being developed to enable the desired extreme fuel burnup levels. Specifically, coatings are being developed to minimize FCCI, and research is underway to fabricate large heats of radiation tolerant oxide dispersion steels with homogeneous oxide dispersions.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Rapid-cycling HTS magnet for muon acceleration

A very wide range of operational temperatures of the HTS (YBCO) superconductor makes it suitable for the construction of rapid-cycling magnets required for the muon acceleration. The measured [3] very low power loss of the 0.4 T magnet operating at 300 T/s suggested a realistic possibility of the HTS-based accelerator magnet with much higher magnetic field and ramp rate. The magnet core and the HTS cable designs for the 2 T field in the 30 mm beam gap are presented. The simulation of the HTS cable hysteresis power loss for the 1000 T/s ramp rate is discussed in terms of the operational temperatures and required cryogenic power.

43 PARTICLE ACCELERATORS↗

WInd-and-react Bi-2212 coil development for accelerator magnets

Sub-scale coils are being manufactured and tested at Lawrence Berkeley National Laboratory in order to develop wind-and-react Bi{sub 2}Sr{sub 2}CaCu{sub 2}O{sub x} (Bi-2212) magnet technology for future graded accelerator magnet use. Previous Bi-2212 coils showed significant leakage of the conductors core constituents to the environment, which can occur during the partial melt reaction around 890 C in pure oxygen. The main origin of the observed leakage is intrinsic leakage of the wires, and the issue is therefore being addressed at the wire manufacturing level. We report on further compatibility studies, and the performance of new sub-scale coils that were manufactured using improved conductors. These coils exhibit significantly reduced leakage, and carry currents that are about 70% of the witness wire critical current (I{sub c}). The coils demonstrate, for the first time, the feasibility of round wire Bi-2212 conductors for accelerator magnet technology use. Successful high temperature superconductor coil technology will enable the manufacture of graded accelerator magnets that can surpass the, already closely approached, intrinsic magnetic field limitations of Nb-based superconducting magnets.

43 PARTICLE ACCELERATORS↗

Ionic charge states of N, Ne, Mg, Si and S in solar energetic particle events

The mean ionic charges and source-region temperatures of flare-accelerated N, Ne, Mg, Si and S in three large solar-energetic-particle events during 1978-1979 are determined from ISEE-3 observations, extending the findings of Hovestadt et al. (1981) and Gloeckler et al. (1981) for C, He, O, and Fe. The results are presented in tables and graphs, and the charge states are shown to correspond to different source temperatures even in the same flare, assuming equilibration in the hot plasma. The electron temperatures range from 2 x 10 to the 6th K for C, N, O, Si, and S, 4 x 10 to the 6th K for Ne and Fe, and 7 x 10 to the 6th K for Mg. The possibility that these temperature inconsistencies reflect different stages in the approach to equilibrium is considered.

Luhn, A.↗