Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “source location”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

Measurement of sputtered efflux from 5-, 8-, and 30-cm diameter mercury ion thrusters

A study was undertaken to investigate the sputtered efflux from 5-, 8-, and 30-cm diameter mercury ion thrusters. Quartz crystal microbalances and fused silica samples were used to analyze the sputtered flux. Spectral transmittance measurements and spectrographic analysis of the samples were made after they were exposed to different thruster effluence by operating the thrusters at various conditions and durations of time. These measurements were used to locate the source of the efflux and determine its accumulated effect at various locations near the thruster. Comparisons of in situ and ex situ transmittance measurements of samples exposed to thruster efflux are also presented.

Weigand, A. J.↗

On the structure of the outer layers of cool carbon stars

Exposures on the spectra of four late C-type stars have been made with the IUE satellite in the wavelength range of the LWR camera (1900-3200 A). Two Mira variables near maximum light and two semiregular variables were observed. Although the exposure times used, which range up to 240 min in the low-resolution mode, were more than sufficient to record the continuum and emission lines of Mg II, Fe II, and Al II in normal M stars of similar magnitude and temperature, no light was recorded. It is concluded that the far-ultraviolet continuum is strongly depressed in these cool carbon stars. The absence of UV emission lines implies either that the chromospheric lines observed in M stars require an ultraviolet flux for their excitation, or that cool carbon stars have no chromosphere at all or that the opacity source is located above even the emission-line-forming region. This opacity source, which is probably some carbon condensate since it is weak or absent in M stars while absorbing strongly in C stars, is discussed both in terms of the chromospheric interpretation of the emission lines and in terms of their shock-wave interpretation.

Querci, F.↗

Dust emission in the Sagittarius B2 molecular cloud core

A model is presented for the dust emission from the Sagittarius B2 molecular cloud core which reproduces the observed spectrum between 30 and 1300 micron, as well as the distribution of the emission at 1300 micron. The model is based on the assumption that Sgr B2(N) continuum source is located behind the dust cloud associated with Sgr B2(M) continuum source. The fact that Sgr B2(N) is stronger at 1300 micron can be attributed to a local column density maximum at the position of this source. Absence of a 53 micron emission peak at the position of Sgr B2(N) suggests that the luminosity of the north source is lower than that of the middle source.

Lis, Dariusz C.↗

Measurements of the spatial structure and directivity of 100 KeV photon sources in solar flares using PVO and ISEE-3 spacecraft

The objective of this grant was to measure the spatial structure and directivity of the hard X-ray and low energy gamma-ray (100 keV-2 MeV) continuum sources in solar flares using stereoscopic observations made with spectrometers aboard the Pioneer Venus Orbiter (PVO) and Third International Sun Earth Explorer (ISEE-3) spacecraft. Since the hard X-ray emission is produced by energetic electrons through the bremsstrahlung process, the observed directivity can be directly related to the 'beaming' of electrons accelerated during the flare as they propagate from the acceleration region in the corona to the chromosphere/transition region. Some models (e.g., the thick-target model) predict that most of the impulsive hard X-ray/low energy gamma-ray source is located in the chromosphere, the effective height of the X-ray source above the photosphere increasing with the decrease in the photon energy. This can be verified by determining the height-dependence of the photon source through stereoscopic observations of those flares which are partially occulted from the view of one of the two spacecraft. Thus predictions about beaming of electrons as well as their spatial distributions could be tested through the analysis proposed under this grant.

Anderson, Kinsey A.↗

Comptel measurements of the gamma-ray burst GRB 930131

On 1993 January 31 at 1857:12 Universal Time (UT), the Imaging Compton Telescope COMPTEL onboard the Compton Gamma Ray Observatory (CGRO) detected the cosmic gamma-ray burst GRB 930131. COMPTEL's MeV imaging capability was employed to locate the source to better than 2 deg (1 sigma error radius) within 7 hr of the event, initiating a world-wide search for an optical and radio counterpart. The maximum likelihood position of the burst from the COMPTEL data is alpha(sub 2000) = 12h 18m, delta(sub 2000) = -9 deg 42 min, consistent with independent CGRO-Burst and Transient Source Experiment (CGRO-BATSE) and Energetic Gamma Ray Experiment Telescope (EGRET) locations as well as with the triangulation annulus constructed using BATSE and Ulysses timing data. The combined COMPTEL and EGRET burst data yield a better estimate of the burst location: alpha(sub 2000) = 12h 18m and delta(sub 2000) = -10 deg 21 min, with a 1 sigma error radius of 32 min. In COMPTEL's energy range, this burst was short, consisting of two separate spikes occurring within a approximately 1 s interval with a low intensity tail for approximately 1 s after the second spike. No statistically significant flux is present for a 30 s period after the main part of the burst. This is consistent with the EGRET data. The COMPTEL telescope events indicate a hard, power-law emission extending to beyond 10 MeV with a spectral index of -1.8 +/- 0.4. The rapid fluctuations and high intensities of the gamma-ray flux greater than 10 MeV place the burst object no farther than 250 pc if the burst emission is not beamed.

Ryan, J.↗

Newly Identified Climatically and Environmentally Significant High-Latitude Dust Sources

Dust particles from high latitudes have a potentially large local, regional, and global significance to climate and the environment as short-lived climate forcers, air pollutants, and nutrient sources. Identifying the locations of local dust sources and their emission, transport, and deposition processes is important for understanding the multiple impacts of high-latitude dust (HLD) on the Earth’s systems. Here, we identify, describe, and quantify the source intensity (SI) values, which show the potential of soil surfaces for dust emission scaled to values 0 to 1 concerning globally best productive sources, using the Global Sand and Dust Storms Source Base Map (G-SDS-SBM). This includes 64 HLD sources in our collection for the northern (Alaska, Canada, Denmark, Greenland, Iceland, Svalbard, Sweden, and Russia) and southern (Antarctica and Patagonia) high latitudes. Activity from most of these HLD sources shows seasonal character. It is estimated that high-latitude land areas with higher (SI ≥ 0.5), very high (SI ≥ 0.7), and the highest potential (SI ≥ 0.9) for dust emission cover > 1 670 000 km 2 , > 560 000 km 2 , and > 240 000 km 2 , respectively. In the Arctic HLD region (≥ 60◦ N), land area with SI ≥ 0.5 is 5.5 % (1 035 059 km 2 ), area with SI ≥ 0.7 is 2.3 % (440 804 km 2 ), and area with SI ≥ 0.9 is 1.1 % (208 701 km 2 ). Minimum SI values in the northern HLD region are about 3 orders of magnitude smaller, indicating that the dust sources of this region greatly depend on weather conditions. Our spatial dust source distribution analysis modeling results showed evidence supporting a northern HLD belt, defined as the area north of 50◦ N, with a “transitional HLD-source area” extending at latitudes 50–58◦ N in Eurasia and 50–55◦ N in Canada and a “cold HLD-source area” including areas north of 60◦ N in Eurasia and north of 58◦ N in Canada, with currently “no dust source” area between the HLD and low-latitude dust (LLD) dust belt, except for British Columbia. Using the global atmospheric transport model SILAM, we estimated that 1.0 % of the global dust emission originated from the high-latitude regions. About 57 % of the dust deposition in snow- and ice-covered Arctic regions was from HLD sources. In the southern HLD region, soil surface conditions are favorable for dust emission during the whole year. Climate change can cause a decrease in the duration of snow cover, retreat of glaciers, and an increase in drought, heatwave intensity, and frequency, leading to the increasing frequency of topsoil conditions favorable for dust emission, which increases the probability of dust storms. Our study provides a step forward to improve the representation of HLD in models and to monitor, quantify, and assess the environmental and climate significance of HLD.

high latitude dust↗

The Uhuru catalog of X-ray sources.

A catalog of X-ray sources observed with the Uhuru satellite is presented. About 70 days of data have been analyzed for this catalog resulting in 125 sources. Approximately two-thirds of the sources are located within plus or minus 20 deg of the galactic plane. Some of the sources at higher galactic latitudes are identified with known extragalactic objects. Most of the strong sources near the galactic plane are found to be variable.

Giacconi, R.↗

Correlation of stress-wave-emission characteristics with fracture aluminum alloys

A study to correlate stress wave emission characteristics with fracture in welded and unwelded aluminum alloys tested at room and cryogenic temperature is reported. The stress wave emission characteristics investigated were those which serve to presage crack instability; viz., a marked increase in:(1) signal amplitude; (2) signal repetition rate; and (3) the slope of cumulative count plotted versus load. The alloys were 7075-T73, 2219-T87 and 2014-T651, welded with MIG and TIG using 2319 and 4043 filler wire. The testing was done with both unnotched and part-through-crack (PTC) tension specimens and with 18-in.-dia subscale pressure vessels. In the latter testing, a real time, acoustic emission, triangulation system was used to locate the source of each stress wave emission. With such a system, multiple emissions from a given location were correlated with defects found by conventional nondestructive inspection.

Hartbower, C. E.↗

Uhuru observations of the globular cluster X-ray source NGC 6712

Two years of Uhuru observations of the globular-cluster X-ray source A1850-08 = NGC 6712 are reported. An X-ray flare with a duration longer than that of reported X-ray bursts but shorter than that of X-ray transients is analyzed during which the source reached an intensity approximately one-third that of the Crab Nebula. It is found that the source shows day-to-day variability similar to that observed for the other six globular-cluster sources and for the great majority of galactic X-ray sources. A location is determined with 90% confidence by combining the Uhuru location with the Ariel 5 error box, and the identification of the X-ray source with the globular cluster is confirmed. Several possible models for the flaring behavior of the source are evaluated.

Cominsky, L.↗

Measurement of Model Noise in a Hard-Wall Wind Tunnel

Identification, analysis, and control of fluid-mechanically-generated sound from models of aircraft and automobiles in special low-noise, semi-anechoic wind tunnels are an important research endeavor. Such studies can also be done in aerodynamic wind tunnels that have hard walls if phased microphone arrays are used to focus on the noise-source regions and reject unwanted reflections or background noise. Although it may be difficult to simulate the total flyover or drive-by noise in a closed wind tunnel, individual noise sources can be isolated and analyzed. An acoustic and aerodynamic study was made of a 7-percent-scale aircraft model in a NASA Ames 7-by-10-ft (about 2-by-3-m) wind tunnel for the purpose of identifying and attenuating airframe noise sources. Simulated landing, takeoff, and approach configurations were evaluated at Mach 0.26. Using a phased microphone array mounted in the ceiling over the inverted model, various noise sources in the high-lift system, landing gear, fins, and miscellaneous other components were located and compared for sound level and frequency at one flyover location. Numerous noise-alleviation devices and modifications of the model were evaluated. Simultaneously with acoustic measurements, aerodynamic forces were recorded to document aircraft conditions and any performance changes caused by geometric modifications. Most modern microphone-array systems function in the frequency domain in the sense that spectra of the microphone outputs are computed, then operations are performed on the matrices of microphone-signal cross-spectra. The entire acoustic field at one station in such a system is acquired quickly and interrogated during postprocessing. Beam-forming algorithms are employed to scan a plane near the model surface and locate noise sources while rejecting most background noise and spurious reflections. In the case of the system used in this study, previous studies in the wind tunnel have identified noise sources up to 19 dB below the normal background noise of the wind tunnel. Theoretical predictions of array performance are used to minimize the width and the side lobes of the beam pattern of the microphone array for a given test arrangement. To capture flyover noise of the inverted model, a 104-element microphone array in a 622-mm-diameter cluster was installed in a 19-mm-thick poly(methyl methacrylate) plate in the ceiling of the test section of the wind tunnel above the aircraft model (see Figure 1). The microphones were of the condenser type, and their diaphragms were mounted flush in the array plate, which was recessed 12.7 mm into the ceiling and covered by a porous aromatic polyamide cloth (not shown in the figure) to minimize boundary-layer noise. This design caused the level of flow noise to be much less than that of flush-mount designs. The drawback of this design was that the cloth attenuated sound somewhat and created acoustic resonances that could grow to several dB at a frequency of 10 kHz.

Soderman, Paul T.↗

Simultaneous observations of hard X-ray and microwave burst sources in a limb flare

Observations of a flare which occurred just behind the west solar limb on 1981 August 3 are reported. A hard X-ray source (20-30 keV) and a microwave source at 5 GHz were observed simultaneously using the Very Large Array and the hard X-ray telescope aboard the Hinotori spacecraft. Both sources were located in the corona, apparently near the tops of two independent coronal arcades or loops. The source may be composed of many thin filaments unresolved by the VLA observations.

Takakura, T.↗

A new method for reconstructing type III trajectories

A local density approximation (LDA) method is developed for reconstructing the trajectories of type III radio bursts through the interplanetary medium. The method uses the measured source directions and the measured frequency drift rates of the type III burst to determine the locations of the radio source in the interplanetary medium at consecutive frequency levels. The technique is used to reconstruct the trajectory of an actual type III burst and the results are compared to the trajectory obtained from the global density law method. The LDA method represents an improvement in that it utilizes more observed data on the type III burst and that it takes full account of the local density variations at the source locations.

Reiner, M. J.↗

NASA's Meteoroid Environments Office's Response to Three Significant Bolide Events Over North America

Being the only U.S. Government entity charged with monitoring the meteor environment, the Meteoroid Environment Office has deployed a network of all sky and wide field meteor cameras, along with the appropriate software tools to quickly analyze data from these systems. However, the coverage of this network is still quite limited, forcing the incorporation of data from other cameras posted to the internet in analyzing many of the fireballs reported by the public and media. A procedure has been developed that determines the analysis process for a given fireball event based on the types and amount of data available. The differences between these analysis process will be explained and outlined by looking at three bolide events, all of which were large enough to produce meteorites. The first example is an ideal event - a bright meteor that occurred over NASA's All Sky Camera Network on August 2, 2014. With clear video of the event from various angles, a high-accuracy trajectory, beginning and end heights, orbit and approximate brightness/size of the event are able to be found very quickly using custom software. The bolide had the potential to have dropped meteorites, so dark flight analysis and modeling was performed, allowing potential fall locations to be mapped as a function of meteorite mass. The second case study was a bright bolide that occurred November 3, 2014 over West Virginia. This was just north of the NASA southeastern all-sky network, and just south of the Ohio-Pennsylvania network. This case study showcases the MEO's ability to use social media and various internet sources to locate videos of the event from obscure sources (including the Washington Monument) for anything that will permit a determination of a basic trajectory and fireball light curve The third case study will highlight the ability to use doppler weather radar in helping locate meteorites, which enable a definitive classification of the impactor. The input data and analysis steps differ for each case study, but the goals remain the same - a trajectory, orbit, and mass estimate for the bolide within hours of the event, and, for events with a high probability of producing meteorites, a location of the strewn field within a day.

Blaauw, Rhiannon C.↗

Preliminary analysis of an extensive one year survey of trace elements and compounds in the suspended particulate matter in Cleveland, Ohio

Preliminary review of a study of trace elements and compound concentrations in the ambient suspended particulate matter in Cleveland, Ohio, measured from August 1971 through June 1973, as a function of source, monitoring location, and meteorological conditions. The study is aimed at the development of techniques for identifying specific pollution sources which could be integrated into a practical system readily usable by an enforcement agency.

King, R. B.↗

Radio Wave Scattering in the Outer Heliosphere: Preliminary Calculations

Detailed first estimates are presented of angular broadening in the outer heliosphere due to scattering of radio waves by density irregularities. The application is to the 2-3 kHz radiation observed by Voyager. Two plausible turbulence models, which account very well for scattering within 1 AU, are extrapolated beyond 10 AU. Both models predict significant angular broadening in the outer heliosphere, accounting semi- quantitatively alone for the source sizes inferred from roll modulation data. Predictions are presented for radial variations in the apparent source size if scattering is important. Comparisons with available data argue that scattering is important (and indeed is the dominant contributor to the apparent source size) and that the radiation source is located in the outer heliosphere. Other evidence that scattering is important, such as the fluctuations in apparent source direction and intensity, are also identified. The effects of scattering should be included in future analyses of the 2-3 kHz emissions.

Cairns, Iver H.↗

Simultaneous microwave observations of solar flares at 6 and 20 cm wavelengths using the VLA

Using the Very Large Array, solar burst observations have been carried out simultaneously at 6 and 20 cm. Structural changes and preheating have been observed in the flaring regions on time scales of minutes to tens of minutes before the onset of the burst impulsive phase. The 6 cm burst sources are located close to the neutral line, or near the legs of a flaring loop. The 20 cm burst sources show complex and extended structures spatially separated from both the preburst emission and the gradual decay phase of the burst. The observations are interpreted in terms of a two-component flare model (bulk heating as well as acceleration of particles), and the physical parameters of the burst sources are derived.

Melozzi, M.↗

G27.4+0.0 - A galactic supernova remnant with a central compact source

High-resolution X-ray and radio images of the galactic supernova remnant G27.4+0.0 are presented. The X-ray image reveals a centrally located compact source of emission which accounts for 25 percent + or - 2 percent of the emission. The rest of the emission is found in diffuse patches defining a circle of diameter 4 arc min. The radio image is an incomplete shell of comparable diameter with no apparent counterpart to the compact X-ray source. The X-ray luminosity of the supernova remmant implied by the distance of 26 kpc inferred from the Sigma-D relationship exceeds that of any known remnant. This fact, plus the relatively low X-ray absorption, suggests that the remnant is substantially closer than 26 kpc. No X-ray variability of the central source has been detected to a level of 50 percent on time scales of about 1 year, and no periodicity in the range 0.0001-100 Hz to a limit of 16 percent was detected. If G27.4 +0.0 is within a few kiloparsecs, the central source is most likely to be an accretion-powered X-ray binary.

Kriss, G. A.↗

'Intermittent' solar periodicities

The signal from a stable periodicity can seem to be intermittent when it is partially masked by an unmodelled window function or when the data set is too short to resolve closely spaced periodicities. By taking this into account, short-lived periodicities in solar data can be reinterpreted as evidence for continuously periodic behavior. The periodic sources are located in the solar interior and caused by global oscillation modes. The convective envelope acts as the window for these sources. Recent reports of seven periodicities from 100 to 1000 days are compared with this model. Precise long-term values for the periodicities are predicted and they agree closely with observations. Some elements are suggested that might explain the well-documented 155-day periodicity. Conventional filtering methods to suppress effects of the 11-year cycle are criticized as inadequate.

Wolff, Charles L.↗