Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “single photon processes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

Optical spin hall effect in exciton–polariton condensates in lead halide perovskite microcavities

An exciton–polariton condensate is a hybrid light–matter state in the quantum fluid phase. The photonic component endows it with characters of spin, as represented by circular polarization. Spin-polarization can form stochastically for quasi-equilibrium exciton–polariton condensates at parallel momentum vector k|| ∼ 0 from bifurcation or deterministically for propagating condensates at k|| > 0 from the optical spin-Hall effect (OSHE). Here, we report deterministic spin-polarization in exciton–polariton condensates at k|| ∼ 0 in microcavities containing methylammonium lead bromide perovskite (CH3NH3PbBr3) single crystals under non-resonant and linearly polarized excitation. We observe two energetically split condensates with opposite circular polarizations and attribute this observation to the presence of strong birefringence, which introduces a large OSHE at k|| ∼ 0 and pins the condensates in a particular spin state. Such spin-polarized exciton–polariton condensates may serve not only as circularly polarized laser sources but also as effective alternatives to ultracold atom Bose–Einstein condensates in quantum simulators of many-body spin–orbit coupling processes.

Chemistry↗

A scanning resonator for probing quantum coherent devices

Superconducting resonators with high quality factors are extremely sensitive detectors of the complex impedance of materials and devices coupled to them. This capability has been used to measure losses in multiple different materials and, in the case of circuit quantum electrodynamics (circuit QED), has been used to measure the coherent evolution of multiple different types of qubits. Here, we report on the implementation of a scanning resonator for probing quantum coherent devices. Our scanning setup enables tunable coherent coupling to systems of interest without the need for fabricating on-chip superconducting resonators. We measure the internal quality factor of our resonator sensor in the single-photon regime to be >104 and demonstrate capacitive imaging using our sensor with zeptoFarad sensitivity and micron spatial resolution at milliKelvin temperatures. We then use our setup to characterize the energy spectrum and coherence times of multiple transmon qubits with no on-chip readout circuitry. Our experiments introduce a new tool for using circuit QED to measure existing and proposed qubit platforms.

47 OTHER INSTRUMENTATION↗

Ternary molecular switching in a single-crystal optical actuator with correlated crystal strain

A growing portfolio of single-crystal optical actuators is forging a new class of photonic materials that hold prospects for quantum technologies. Ruthenium-based complexes that exhibit this phenomenon via SO 2 -linkage photoisomerisation are of particular interest since they display multiple metastable states, once induced by green light; yet, complete photoconversion into each SO 2 -isomeric state is rarely achieved. We discover a new complex, trans-[Ru(SO 2 )(NH 3 ) 4 (4-bromopyridine)]tosylate 2 , that produces 100% photoconverted η 1 -OSO isomeric crystal structures at 90 K, which fully transition into η 2 -(OS)O photoisomers upon warming to 100 K, while the dark-state η 1 -SO 2 structure is wholly recovered by heating the crystal to room temperature. Crystal structures and optical-absorption profiles of each state are captured via in-situ light-induced single-crystal X-ray diffraction and optical-absorption spectroscopy. Results show that both photoisomeric species behave as optical switches, but with distinct optical properties. The photoisomerisation process causes thermally-reversible micro- and nanoscopic crystal strain, as characterised by optical microscopy and in-situ light-induced atomic-force microscopy.

actuators↗

Universal control in bosonic systems with weak Kerr nonlinearities

Resonators with weak single-photon self-Kerr nonlinearities can theoretically be used to prepare Fock states in the presence of a loss much larger than their nonlinearities. Two necessary ingredients are large displacements and a two-photon (parametric) drive. Here, in this study, we find that these systems can be controlled to achieve any desired gate operation in a finite-dimensional subspace (whose dimensionality can be chosen at will). Moreover, we show that the two-photon driving requirement can be relaxed and that full controllability is achievable with only one-photon (linear) drives. We make use of both Trotter-Suzuki decompositions and gradient-based optimization to find control pulses for a desired gate, which reduces the computational overhead by using a small blockaded subspace. We also discuss the infidelity arising from input power limitations in realistic settings, as well as from corrections to the rotating-wave approximation. Our universal control protocol opens the possibility for quantum information processing using a wide range of lossy systems with weak nonlinearities.

Yuan, Ming [Univ. of Chicago, IL (United States)] ↗

Kinetics of Nucleation and Crystal Growth in Glass Forming Melts in Microgravity

This flight definition project has the specific objective of investigating the kinetics of nucleation and crystal growth in high temperature inorganic oxide, glass forming melts in microgravity. It is related to one1 of our previous NASA projects that was concerned with glass formation for high temperature containerless melts in microgravity. The previous work culminated in two experiments which were conducted aboard the space shuttle in 1983 and 1985 and which consisted of melting (at 1500 C) and cooling levitated 6 to 8 mm diameter spherical samples in a Single Axis Acoustic Levitator (SAAL) furnace. Compared to other types of materials, there have been relatively few experiments, 6 to 8, conducted on inorganic glasses in space. These experiments have been concerned with mass transport (alkali diffusion), containerless melting, critical cooling rate for glass formation, chemical homogeneity, fiber pulling, and crystallization of glass forming melts. One of the most important and consistent findings in all of these experiments has been that the glasses prepared in microgravity are more resistant to crystallization (better glass former) and more chemically homogeneous than equivalent glasses made on earth (1g). The chemical composition of the melt appears relatively unimportant since the same general results have been reported for oxide, fluoride and chalcogenide melts. These results for space-processed glasses have important implications, since glasses with a higher resistance to crystallization or higher chemical homogeneity than those attainable on earth can significantly advance applications in areas such as fiber optics communications, high power laser glasses, and other photonic devices where glasses are the key functional materials. The classical theories for nucleation and crystal growth for a glass or melt do not contain any parameter that is directly dependent upon the g-value, so it is not readily apparent why glasses prepared in microgravity should be more resistant to crystallization than equivalent glasses prepared on earth. Similarly, the gravity-driven convection in a fluid melt is believed to be the primary force field that is responsible for melt homogenization on earth. Thus, it is not obvious why a glass prepared in space, where gravity-driven convection is ideally absent, would be more chemically homogeneous than a glass identically prepared on earth. The primary objective of the present research is to obtain experimental data for the nucleation rate and crystal growth rate for a well characterized silicate melt (lithium disilicate) processed entirely in space (low gravity) and compare these rates with the nucleation and crystal growth rates for a similar glass prepared identically on earth (1g).

Day, Delbert E.↗

Kinetics of Nucleation and Crystal Growth in Glass Forming Melts in Microgravity

This flight definition project has the specific objective of investigating the kinetics of nucleation and crystal growth in high temperature inorganic oxide, glass forming melts in microgravity. It is related to one of our previous NASA projects that was concerned with glass formation for high temperature containerless melts in microgravity. The previous work culminated in two experiments which were conducted aboard the space shuttle in 1983 and 1985 and which consisted of melting (at 1500 C) and cooling levitated 6 to 8 mm diameter spherical samples in a Single Axis Acoustic Levitator (SAAL) furnace. Compared to other types of materials, there have been relatively few experiments, 6 to 8, conducted on inorganic glasses in space. These experiments have been concerned with mass transport (alkali diffusion), containerless melting, critical cooling rate for glass formation, chemical homogeneity, fiber pulling, and crystallization of glass forming melts. One of the most important and consistent findings in all of these experiments has been that the glasses prepared in microgravity are more resistant to crystallization (better glass former) and more chemically homogeneous than equivalent glasses made on Earth (1 g). The chemical composition of the melt appears relatively unimportant since the same general results have been reported for oxide, fluoride and chalcogenide melts. These results for space-processed glasses have important implications, since glasses with a higher resistance to crystallization or higher chemical homogeneity than those attainable on Earth can significantly advance applications in areas such as fiber optics communications, high power laser glasses, and other photonic devices where glasses are the key functional materials.

Day, Delbert E.↗

A review of criticality dosimetry at the Y-12 National Security Complex and practical importance of dose accuracy in emergency response

A nuclear criticality results in the emission of both neutron and gamma radiation and can produce doses to personnel near the event that exceed 0.1 Gy (10 rad). The primary purpose of nuclear accident dosimetry is to rapidly identify affected personnel in need of prompt medical treatment and to reassure personnel who have been only minimally exposed. While accurate dosimetry is desired, it must be recognized that dose determinations made from whole-body dosimeters or simple triage methods are very rough estimates and contain significant uncertainties. Even when accounting for factors like varying neutron energy spectra, mean photon energies, body orientation within the radiation field, and transient effects on dosimeter response, etc., the end value is a dosimetric quantity defined for very specific radiological conditions and determined within a simple phantom usually at a single depth. Of more importance is the biological response to the radiation, which will vary by person and can be affected by the individual’s radiation sensitivity, age, gender, mass, and underlying health conditions. The overall biological, person-specific response to a given dose cannot be precisely determined except by patient symptom observation and individual biological dosimetry (e.g. chromosome analysis, lymphocyte ratios, etc.). This work describes and discusses the criticality accident dosimetry program at the Y-12 National Security Complex, a United States Department of Energy National Nuclear Security Administration facility. In conclusion, the primary goals of the Y-12 accident dosimetry program are, among others, the rapid identification of significantly exposed persons, prompt routing of exposed workers for medical evaluation and treatment, and the ultimate processing of dosimeters to assign doses to personnel.

61 RADIATION PROTECTION AND DOSIMETRY↗

Robust negativity in the quantum-to-classical transition of Kerr dynamics

Here, we quantify the quantum-to-classical transition of the single-mode Kerr nonlinear dynamics in the presence of loss. We establish three timescales that govern the dynamics, each with distinct characteristics. For times short compared with the Ehrenfest time, the evolution is classical, characterized by Gaussian dynamics. For sufficiently long times, as we increase the initial photon number, unitary Kerr evolution would generate macroscopic superpositions of coherent states (so-called kitten states). However, this is severely restricted in the presence of small photon loss, and the expectation values of observables coincide with their classical values. The intermediate timescale, however, shows resilient quantum behavior in the macroscopic limit. We show that in the mean-field non-Gaussian regime, the Kerr Hamiltonian (with small photon loss) generates a significant amount of Wigner-negativity, and classical flow is recovered only if the loss rate grows with system size. Our results broaden the usual understanding of quantum-to-classical transitions and demonstrate the potential for creating robust nonclassical resources for continuous-variable quantum information processing in the presence of loss.

Raza, Mohsin [University of New Mexico, Albuquerqu↗

Measurement of neutral current single π 0 production on argon with the MicroBooNE detector

We report the first measurement of π 0 production in neutral current (NC) interactions on argon with average neutrino energy of ≲1 GeV. We use data from the MicroBooNE detector’s 85-tonne active volume liquid argon time projection chamber situated in Fermilab’s Booster Neutrino Beam and exposed to 5.89 × 10 20 protons on target for this measurement. Measurements of NC π 0 events are reported for two exclusive event topologies without charged pions. Those include a topology with two photons from the decay of the π 0 and one proton and a topology with two photons and zero protons. Flux-averaged cross-sections for each exclusive topology and for their semi-inclusive combination are extracted (efficiency-correcting for two-plus proton final states), and the results are compared to predictions from the GENIE, NEUT, and NUWRO neutrino event generators. We measure cross sections of 1.243 ± 0.185 (syst) ±0.076 (stat), 0.444 ± 0.098 ± 0.047, and 0.624 ± 0.131 ± 0.075 [10 -38 cm 2 /Ar] for the semi-inclusive NCπ 0 , exclusive NCπ 0 +1p, and exclusive NCπ 0 +0p processes, respectively.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Development of a Mars Lidar (MARLI) for Measuring Wind and Aerosol Profiles from Orbit

Our understanding of the Mars atmosphere and the coupled atmospheric processes that drive its seasonal cycles is limited by a lack of observation data, particularly measurements that capture diurnal and seasonal variations on a global scale. As outlined in the 2011 Planetary Science Decadal Survey and the recent Mars Exploration Program Analysis Group(MEPAG) Goals Document, near-polar-orbital measurements of height-resolved aerosol backscatter and wind profiles area high-priority for the scientific community and would be valuable science products as part of a next-generation orbital science package. To address these needs, we have designed and tested a breadboard version of a direct detection atmospheric wind lidar for Mars orbit. It uses a single-frequency, seeded Nd:YAG laser ring oscillator operating at 1064nm (4 kHz repetition rate), with a 30-ns pulse duration amplified to 4 mJ pulse energy. The receiver uses a Fabry-Perotetalon as part of a dual-edge optical discrimination technique to isolate the Doppler-induced frequency shift of the back scattered photons. To detect weak aerosol backscatter profiles, the instrument uses a 4x4 photon-counting HgCdTeAPD detector with a 7 MHz bandwidth and < 0.4 fW/Hz(exp 1/2) noise equivalent power. With the MARLI lidar breadboard instrument, we were able to measure Doppler shifts continuously between 1 and 30 m/s by using a rotating chopper wheel to impart a Doppler shift to incident laser pulses. We then coupled the transmitter and receiver systems to a laser ranging telescope at the Goddard Geophysical and Astronomical Observatory (GGAO) to measure backscatter and Doppler wind profiles in the atmosphere from the ground. We measured a 5.3 ± 0.8 m/s wind speed from clouds in the planetary boundary layer at a range of 4 to 6 km. This measurement was confirmed with a range-over-time measurement to the same clouds as well as compared to EMC meteorological models. Here we describe the lidar approach and the breadboard instrument, and report some early results from ongoing field experiments.

Cremons, Daniel R.↗

Cloud-top pressure retrieval with DSCOVR EPIC oxygen A- and B-band observations

An analytic transfer inverse model for Earth Polychromatic Imaging Camera (EPIC) observations is proposed to retrieve the cloud-top pressure (CTP) with the consideration of in-cloud photon penetration. In this model, an analytic equation was developed to represent the reflection at the top of the atmosphere from above cloud, in cloud, and below cloud. The coefficients of this analytic equation can be derived from a series of EPIC simulations under different atmospheric conditions using a nonlinear regression algorithm. With estimated cloud pressure thickness, the CTP can be retrieved from EPIC observation data by solving the analytic equation. To simulate the EPIC measurements, a program package using the double-k approach was developed. Compared to line-by-line calculation, this approach can calculate high-accuracy results with a 100-fold computation time reduction. During the retrieval processes, two kinds of retrieval results, i.e., baseline CTP and retrieved CTP, are provided. The baseline CTP is derived without considering in-cloud photon penetration, and the retrieved CTP is derived by solving the analytic equation, taking into consideration in-cloud and below-cloud interactions. The retrieved CTPs for the oxygen A and B bands are smaller than their related baseline CTP. At the same time, both baseline CTP and retrieved CTP at the oxygen B band are larger than those at the oxygen A band. Compared to the difference in baseline CTP between the B band and A band, the difference in retrieved CTP between these two bands is generally reduced. Out of around 10 000 cases, in retrieved CTP between the A and B bands we found an average bias of 93 mb with a standard deviation of 81 mb. The cloud layer top pressure from Cloud–Aerosol Lidar and Infrared Pathfinder Satellite Observations (CALIPSO) measurements is used for validation. Under single-layer cloud situations, the retrieved CTPs for the oxygen A band agree well with the CTPs from CALIPSO, the mean difference of which within 5 mb in the case study. Under multiple-layer cloud situations, the CTPs derived from EPIC measurements may be larger than the CTPs of high-level thin clouds due to the effect of photon penetration.

DSCOVR↗

Quantum Light Emission from Coupled Defect States in DNA-Functionalized Carbon Nanotubes

Solid-state single-photon sources are essential building blocks for quantum photonics and quantum information technologies. This study demonstrates promising single-photon emission from quantum defects generated in single-wall carbon nanotubes (SWCNTs) by covalent reaction with guanine nucleotides in their single-stranded DNA coatings. Low-temperature photoluminescence spectroscopy and photon-correlation measurements on individual guanine-functionalized SWCNTs (GF-SWCNTs) indicate that multiple, closely spaced guanine defect sites within a single ssDNA strand collectively form an exciton trapping potential that supports a localized quantum state capable of room-temperature single-photon emission. In addition, exciton traps from adjacent ssDNA strands are weakly coupled to give cross-correlations between their separate photon emissions. Theoretical modeling identifies coupling mechanism as a capture of band-edge excitons. Finally, because the spatial pattern of nanotube functionalization sites can be readily controlled by selecting ssDNA base sequences, GF-SWCNTs should become a versatile family of quantum light emitters with engineered properties.

36 MATERIALS SCIENCE↗

High-Resolution Momentum Imaging—From Stern’s Molecular Beam Method to the COLTRIMS Reaction Microscope [Book Chapter]

Multi-particle momentum imaging experiments are now capable of providing detailed information on the properties and the dynamics of quantum systems in Atomic, Molecular and Photon (AMO) physics. Historically, Otto Stern can be considered the pioneer of high-resolution momentum measurements of particles moving in a vacuum and he was the first to obtain sub-atomic unit (a.u.) momentum resolution (Schmidt-Böcking et al. in The precision limits in a single-event quantum measurement of electron momentum and position, these proceedings). A major contribution to modern experimental atomic and molecular physics was his so-called molecular beam method, which Stern developed and employed in his experiments. With this method he discovered several fundamental properties of atoms, molecules and nuclei. As corresponding particle detection techniques were lacking during his time, he was only able to observe the averaged footprints of large particle ensembles. Today it is routinely possible to measure the momenta of single particles, because of the tremendous progress in single particle detection and data acquisition electronics. A “state-of-the-art” COLTRIMS reaction microscope can measure, for example, the momenta of several particles ejected in the same quantum process in coincidence with sub-a.u. momentum resolution. Such setups can be used to visualize the dynamics of quantum reactions and image the entangled motion of electrons inside atoms and molecules. This review will briefly summarize Stern’s work and then present in longer detail the historic steps of the development of the COLTRIMS reaction microscope. Furthermore, some benchmark results are shown which initially paved the way for a broad acceptance of the COLTRIMS approach. Finally, a small selection of milestone work is presented which has been performed during the last two decades.

Jahnke, T.↗

Solid state photomultiplier for astronomy, phase 2

Epitaxial layers with varying donor concentration profiles were grown on silicon substrate wafers using chemical vapor deposition (CVD) techniques, and solid state photomultiplier (SSPM) devices were fabricated from the wafers. Representative detectors were tested in a low background photon flux, low temperature environment to determine the device characteristics for comparison to NASA goals for astronomical applications. The SSPM temperatures varied between 6 and 11 K with background fluxes in the range from less than 5 x 10 to the 6th power to 10 to the 13th power photons/square cm per second at wavelengths of 3.2 and 20 cm. Measured parameters included quantum efficiency, dark count rate and bias current. Temperature for optimal performance is 10 K, the highest ever obtained for SSPMs. The devices exhibit a combination of the lowest dark current and highest quantum efficiency yet achieved. Experimental data were reduced, analyzed and used to generate recommendations for future studies. The background and present status of the microscopic theory of SSPM operation were reviewed and summarized. Present emphasis is on modeling of the avalanche process which is the basis for SSPM operation. Approaches to the solution of the Boltzmann transport equation are described and the treatment of electron scattering mechanisms is presented. The microscopic single-electron transport theory is ready to be implemented for large-scale computations.

Besser, P. J.↗

Novel In-situ Patterning Technique to Fabricate Single Quantum Dots for Quantum Photonics

Photon sources able to emit single or entangled photon pairs are key components in quantum information systems. Semiconductor quantum dots (QDs) are promising candidates due to their high efficiencies and ease of integration with other photonic or electronic components. State-of-the-art QDs, however, are limited to certain emission wavelengths and specific applications due to material choice constraints and their randomness in shape/size. This project is focused on developing a novel in-situ patterning technique to realize QDs with a broad emission range, shape/size control and the ability to emit single/entangled photons. Our approach has two key elements: (1) In-situ patterning via arsenic-induced nanovoid etching on antimonide surfaces and (2) In-filling of nanovoids to form QDs. By closely controlling the experimental conditions, it is shown that this technique can be used to realize III-V QDs in As 2 - etched nanovoids on a GaSb surface. The exposure to As 2 in terms of substrate temperature, time and flux is found to have a significant impact on the process variables such as nanovoid depth, QD dimensions etc. An in-depth analysis of the etch mechanism reveals that by controlling the As 2 exposure, uniform 3-dimensional nanostructures with varying areal densities can be obtained without an in-filling step. Preliminary optical characterization of these nanostructures shows that these QDs may be relevant for realizing emitters in the telecom wavelength range.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

An investigation of a mathematical model of an optically pumped Ti(3+):Al2O3 laser system

During the last several years, solid state lasers were developed that have the potential for meeting rigorous performance requirements for space-based remote sensing of the atmosphere. In order to design a stable and efficient laser and to understand the effect on laser output of changes in the physical and design parameters, an understanding of the development of the dynamical processes of the laser is necessary. Typically, the dynamical processes in a laser system are investigated via rate equations describing the evolution of the occupancy in the electronic levels and of the photon density in the laser cavity. There are two approaches to this type of study. Most often, for the sake of simplicity, the spatial variations of the dynamic variables in the laser system are disregarded and the mathematical model consists of a system of first order nonlinear ordinary differential equations (ODE). The second approach is to take into account both spatial and temporal variations in the dynamic variables in the laser cavity. The resulting model consists of a first order semilinear system of partial differential equations (PDE). The model which was studied was studied was generic in the sense that it was a four-level laser system, but the parameters used in the numerical study were specific to Titanium-doped sapphire. For simplicity, a constant, spatially uniform pumping scheme was considered. In addition, a simplification of the model was made so that it treats a single lasing wavelength with a narrow bandwidth. The purpose was to investigate both versions of the mathematical model and to determine whether the numerical solutions are similar both qualitatively and quantitatively. The systems of ordinary differential equations were solved numerically using a Runge-Kutta-Fehlberg algorithm which was very efficient for typical values of the physical parameters. A numerical scheme, based on the Modified Euler method, for computing solutions to the system of partial differential equations was developed and implemented. The PDE model was solved numerically at the expense of greatly increased computer time.

Roberts, Lila F.↗

Using sub-limb observations to measure gravity waves excited by convection

Convective gravity waves are a major driver of atmospheric circulation, including the stratospheric and mesospheric quasi-biennial oscillation (QBO) and the Brewer–Dobson circulation. Previous work shows clear evidence that these waves can be excited by both single convective cells and by mesoscale convective complexes acting as a single unit. However, the partitioning of the generated waves and, crucially for atmospheric model development, the flux of momentum they transport between these two types of excitation process remains highly uncertain due to a fundamental lack of suitable observations at the global scale. Here, we use both theoretical calculations and sampled output from a high-resolution weather model to demonstrate that a satellite instrument using a sub-limb geometry would be well suited to characterising the short-vertical short-horizontal gravity waves these systems produce, and hence to provide the scientific knowledge needed to identify the relative wave-driving contribution of these two types of convective wave excitation.

54 ENVIRONMENTAL SCIENCES↗

ICESat-2 Atmospheric Channel Description, Data Processing and First Results

The Advanced Topographic Laser Altimeter System (ATLAS) was launched aboard the Ice Cloud and land-Elevation Satellite-2 (ICESat-2) satellite in September 2018. ATLAS is a single wavelength (532 nm) lidar system designed to acquire high resolution measurements of the earth's surface while also obtaining atmospheric backscatter from molecules, clouds, and aerosols. Because ATLAS is optimized for altimetry, the atmospheric data acquired is unique in many respects and requires non-standard analysis techniques. For example, the high repetition rate laser limits the vertical extent of the profiles to just 14 km and causes atmospheric scattering from above 15 km to be added to the scattering in the lower 0–14 km profile. In addition, the limited vertical range of the acquired profiles renders it difficult to compute the magnitude of the solar background and hinders the application of standard calibration techniques. Despite these limitations, methods have been developed to successfully produce data products that have value to the atmospheric community for cloud and aerosol research and are currently available at the National Snow and Ice Data Center (NSIDC). In this paper we describe the ICESat-2 atmospheric channel and the methods used to process the ATLAS raw photon count data to obtain calibrated backscatter and higher level products such as layer heights and type, blowing snow, column optical depth and apparent surface reflectance.

Stephen P Palm↗