Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “performance based design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
NASA NTRS2022

Conceptual Design of a Tiltduct Reference Vehicle for Urban Air Mobility

NASA is establishing a fleet of conceptual air vehicle designs to support research and development for Urban Air Mobility (UAM). This fleet of vehicles will enable examination of the sensitivity of UAM vehicle designs to technology assumptions, identify key research and development needs for UAM aircraft, and provide the UAM community with reference vehicles that are publicly available and based upon known assumptions. To date, five six-passenger UAM reference vehicles have been published: a single-main-rotor helicopter, a side-by-side helicopter, a quadrotor, a lift-plus-cruise, and a tiltwing. To increase the breadth of vehicle technologies encapsulated in the fleet of NASA UAM reference vehicles, this paper establishes a tiltduct vehicle as an addition to the fleet. The fleet will continue to evolve as future analyses and trade studies are performed. The tiltduct UAM reference vehicle has six tilting ducted proprotors. This paper describes the initial configuration downselection; discusses ducted proprotor design rules of thumb as they applied to the conceptual design of the reference vehicle; describes the vehicle sizing, trade studies, and tuning of models performed; and finally, compares the resulting tiltduct vehicle against the other six-passenger NASA UAM reference vehicles. The high-level analyses performed for this study did not indicate significant differences in performance between the tiltduct and tiltwing reference vehicles, and so vehicle performance alone may not be a key driver in the selection of a tiltduct vehicle over a tiltwing vehicle. However, if ducts are found to have significant acoustical benefits, then acoustical priorities may provide a compelling reason to incorporate ducted proprotors. One significant limitation of the design presented in this paper is that the ducted proprotor performance was tuned based upon performance characteristics observed during historical tests with disk loadings (defined as thrust divided by proprotor disk area) of 125-250 lb/ft$^2$. The tiltduct vehicle designed in this study has a disk loading of 30 lb/ft$^2$, to be more representative of UAM vehicles; further studies to understand performance of ducted proprotors at representative disk loadings are warranted.

Tiltduct↗
NASA NTRS2003

Process-Based Cost Estimation for Ramjet/Scramjet Engines

Process-based cost estimation plays a key role in effecting cultural change that integrates distributed science, technology and engineering teams to rapidly create innovative and affordable products. Working together, NASA Glenn Research Center and Boeing Canoga Park have developed a methodology of process-based cost estimation bridging the methodologies of high-level parametric models and detailed bottoms-up estimation. The NASA GRC/Boeing CP process-based cost model provides a probabilistic structure of layered cost drivers. High-level inputs characterize mission requirements, system performance, and relevant economic factors. Design alternatives are extracted from a standard, product-specific work breakdown structure to pre-load lower-level cost driver inputs and generate the cost-risk analysis. As product design progresses and matures the lower level more detailed cost drivers can be re-accessed and the projected variation of input values narrowed, thereby generating a progressively more accurate estimate of cost-risk. Incorporated into the process-based cost model are techniques for decision analysis, specifically, the analytic hierarchy process (AHP) and functional utility analysis. Design alternatives may then be evaluated not just on cost-risk, but also user defined performance and schedule criteria. This implementation of full-trade study support contributes significantly to the realization of the integrated development environment. The process-based cost estimation model generates development and manufacturing cost estimates. The development team plans to expand the manufacturing process base from approximately 80 manufacturing processes to over 250 processes. Operation and support cost modeling is also envisioned. Process-based estimation considers the materials, resources, and processes in establishing cost-risk and rather depending on weight as an input, actually estimates weight along with cost and schedule.

Singh, Brijendra↗
NASA NTRSDate not supplied

Towards Low-Noise Design of a Proprotor with the Vortex Lattice Method and Gradient-Based Optimization

This work aims to combine an aerodynamic model based on the unsteady vortex lattice method with an acoustic model provided by Farassat's formulation 1A to perform gradient-based optimizations of a proprotor with aerodynamic and acoustic constraints. The resulting combination of tools is applied to the problem of designing a single proprotor operating at a cruise condition, with and without an acoustic constraint and wing placed downstream of the proprotor rotation plane. Results are compared to a baseline design studied previously, and to similar optimizations performed with a simpler blade element momentum theory aerodynamic model. Each optimization case achieved feasibility and made significant improvements in the objective function, but the optimality criterion was not satisfied. Overall the designs the optimizer found roughly comported with our previous experience with similar problems, with some discrepancies that are discussed.

Aerodynamics↗
NASA NTRSDate not supplied

Towards Low-Noise Design of a Proprotor with the Vortex Lattice Method and Gradient-Based Optimization

This work aims to combine an aerodynamic model based on the unsteady vortex lattice method with an acoustic model provided by Farassat's formulation 1A to perform gradient-based optimizations of a proprotor with aerodynamic and acoustic constraints. The resulting combination of tools is applied to the problem of designing a single proprotor operating at a cruise condition, with and without an acoustic constraint and wing placed downstream of the proprotor rotation plane. Results are compared to a baseline design studied previously, and to similar optimizations performed with a simpler blade element momentum theory aerodynamic model. Each optimization case achieved feasibility and made significant improvements in the objective function, but the optimality criterion was not satisfied. Overall the designs the optimizer found roughly comported with our previous experience with similar problems, with some discrepancies that are discussed.

Aerodynamics↗
NASA NTRS1993

On the Accuracy of CFD-Based Pressure Drop Predictions for Right-Angle Ducts

The predictive capability of computational fluid dynamics (CFD) codes for turbulent flow through curved ducts is of significant importance to the design and performance analysis of modern rocket engine flowpaths. Code calibration and validation studies for this class of flow are desireable to estimate the performance margin and operating range of components designed using Navier-Stokes methods. Parametric experimental studies such as that of Weske (NACA ARR W-39) provided a wealth of performance data for the design of single- and compound elbow configurations with various cross-sections, curvature and aspect ratios at varying Reynolds numbers. In that work, the majority of data is presented in the form of loss coefficients, characterizing pressure losses due to duct curvature, and including losses due to wall friction. Using measured friction coefficients, losses of equivalent straight lengths of duct are subtracted, resulting in performance curves useful for design computations. These data are currently used in a CFD-based parametric study covering a broad range of operating conditions. Of particular interest for the accuracy of CFD predictions are the effects on pressure loss due to inlet boundary layer thickness (dependent on upstream development length), and the wall treatment for the turbulence equations (conventional wall functions vs. wall integration using a two-layer model). The experimental data are reassessed in the form of an error analysis, and are compared with CFD predictions for 18 computational cases. Grid-independence, grid spacing, and convergence requirements of the cases are discussed. Conclusions regarding the relative importance of the parametric variables will be presented.

Brankovic, Andreja↗
NASA NTRS2012

Preliminary Assessment of Variable Speed Power Turbine Technology on Civil Tiltrotor Size and Performance

A Large Civil Tiltrotor (LCTR) conceptual design was developed as part of the NASA Heavy Lift Rotorcraft Systems Investigation in order to establish a consistent basis for evaluating the benefits of advanced technology for large tiltrotors. The concept has since evolved into the second-generation LCTR2, designed to carry 90 passengers for 1,000 nm at 300 knots, with vertical takeoff and landing capability. This paper performs a preliminary assessment of variable-speed power turbine technology on LCTR2 sizing, while maintaining the same, advanced technology engine core. Six concepts were studied; an advanced, single-speed engine with a conventional power turbine layout (Advanced Conventional Engine, or ACE) using a multi-speed (shifting) gearbox. There were five variable-speed power turbine (VSPT) engine concepts, comprising a matrix of either three or four turbine stages, and fixed or variable guide vanes; plus a minimum weight, twostage, fixed-geometry VSPT. The ACE is the lightest engine, but requires a multi-speed (shifting) gearbox to maximize its fuel efficiency, whereas the VSPT concepts use a lighter, fixed-ratio gearbox. The NASA Design and Analysis of Rotorcraft (NDARC) design code was used to study the trades between rotor and engine efficiency and weight. Rotor performance was determined by Comprehensive Analytical Model of Rotorcraft Aerodynamics and Dynamics (CAMRAD II), and engine performance was estimated with the Numerical Propulsion System Simulation (NPSS). Design trades for the ACE vs. VSPT are presented in terms of vehicle gross and empty weight, propulsion system weight and mission fuel burn for the civil mission. Because of its strong effect on gearbox weight and on both rotor and engine efficiency, rotor speed was chosen as the reference design variable for comparing design trades. Major study assumptions are presented and discussed. Impressive engine power-to-weight and fuel efficiency reduced vehicle sensitivity to propulsion system choice. The 10% weight penalty for multi-speed gearbox was more significant than most engine technology weight penalties to the vehicle design because drive system weight is more than two times engine weight. Based on study assumptions, fixed-geometry VSPT concept options performed better than their variable-geometry counterparts. Optimum design gross weights varied 1% or less and empty weights less than 2% among the concepts studied, while optimum fuel burns varied up to 5%. The outcome for some optimum configurations was so unexpected as to recommend a deeper look at the underlying technology assumptions.

Snyder, Christopher A.↗
NASA NTRS1997

Improved Hypersonic Inlet Performance Using Validated Strut Compression Designs

Aerojet is currently executing two Strutjet propulsion contracts: one a Rocket Based Combined Cycle (RBCC) engine for a NASA-Marshall Space Flight Center (MSFC) Advanced Reusable Transportation Technology (ARTT) program, the second a Dual Mode Ram/Scramjet engine for a USAF Wright Laboratories Storable Fuel Scramjet Flow Path Concepts program. The engines employed in both programs operate at supersonic and low hypersonic speeds and use inlets employing forebody external and sidewall compression. Aerojet has developed and validated a successful design methodology applicable to these inlet types. Design features include an integrated vehicle forebody, external side compression struts, strut sidewall and throat bleed, a throat shock trap, and variable geometry internal contraction. Computation Fluid Dynamic (CFD) predictions and test data show these inlets allow substantially increased flow turning angles over other designs. These increased flow turning angles allow shorter and lighter engines than current designs, which in turn enables higher performing vehicles with broad operating characteristics. This paper describes the designs of two different inlets evaluated by the NASA-MSFC and USAF programs, discusses the results of wind tunnel tests performed by NASA-Lewis Research Center, and provides correlations of test data with CFD predictions. Parameters of interest include low Mach number starting capability, start sensitivity as a function of back pressure at various contraction ratios, flow turning angles, strut and throat bleed effects, and pressure recovery at various Mach numbers.

Bulman, M. J.↗
NASA NTRS1981

Quiet short-haul research aircraft familiarization document, revision 1

The design features and general characteristics of the Quiet Short Haul Research Aircraft are described. Aerodynamic characteristics and performance are discussed based on predictions and early flight test data. Principle airplane systems, including the airborne data acquisition system, are also described. The aircraft was designed and built to fulfill the need for a national research facility to explore the use of upper surface blowing, propulsive lift technology in providing short takeoff and landing capability, and perform advanced experiments in various technical disciplines such as aerodynamics, propulsion, stability and control, handling qualities, avionics and flight control systems, trailing vortex phenomena, acoustics, structure and loads, operating systems, human factors, and airworthiness/certification criteria. An unusually austere approach using experimental shop practices resulted in a low cost and high research capability.

Eppel, J. C.↗
NASA NTRS2022

NASA Physics of Failure (PoF) for Reliability

An item’s reliability or longevity is dependent not only on its design but also on how it is used, manufactured, tested, and the stresses it has or will experience. Stresses include operational and environmental exposures to thermal, voltage, current, age/exposure, mechanical, and radiation mechanisms. Therefore, in reliability analysis, it is important to consider the contributions of all of these factors when predicting the failure rates of components. Historically, there has been a reliance on handbook data (e.g., MIL-HDBK-217), but experience has shown that these values and distributions are not representative of actual performance (1,2). Therefore, to make more credible reliability and risk assessments for its missions, NASA must transition to estimating likelihoods of failure based on an item’s reliability/longevity factors (or the physical susceptibilities and strengths impacting the design’s performance) has or will experience, whenever possible. To facilitate this transition a “Handbook on Methodology for Physics of Failure Based Reliability Assessments” has been developed by NASA to assist in applying physics experiences or experiment physics for empirical analysis and conceptualized physics exposures or theoretical physics for deterministic analysis, to develop and aggregate realistic likelihoods of failure leading to more credible forecasts of item performance and longevity. In addition, since it is NASA’s intention that this document continues to evolve based on community lessons learned and the introduction of new assessment methodologies, NASA is encouraging and appreciates the contributions of current and future authors to maintain and enhance this handbook and its supporting case studies.

Physics of Failure↗
NASA NTRS1992

Analysis and optimal design of thick composite structures with passive damping considerations

A design methodology to tailor thick composite plates for optimal static and damping performance is presented. The method is based on discrete layer composite mechanics, hence, is suitable for thick composite laminates. The design criteria include static deflections, frequency and damping constraints. Evaluations on cross-ply simply-supported plates illustrate the advantages of the methodology. Comparisons with design methods based on the classical laminate theory show significant deviations in the resultant optimal designs at higher thicknesses.

Saravanos, D. A.↗
NASA NTRS2011

Assessing the Lifetime Performance of the Lightning Imaging Sensor (LIS): Implications for the Geostationary Lightning Mapper (GLM)

The Lightning Imaging Sensor (LIS) onboard the Tropical Rainfall Measuring Mission (TRMM) satellite has been providing observations of total lightning over the Earth s Tropics for 13 years. This study examines the performance of the LIS throughout its time in orbit. Application of the Deep Convective Cloud Technique (DCCT) (Doelling et al., 2004) was performed on the LIS background pixels to assess the stability of the LIS instrument. The DCCT analysis indicates that the maximum deviation of the monthly mean radiance is within 2% of the overall mean, indicating stable performance over the period. In addition, an examination of the number of flashes detected over time similarly shows no significant trend (after adjusting for the orbit boost that occurred in August 2001). These and other results indicate that there has been no discernible change in LIS performance throughout its lifetime. A similar approach will used for monitoring the performance of the Geostationary Lightning Mapper (GLM) onboard the next generation Geostationary Operational Environmental Satellite-R (GOES-R). Since GLM is based on LIS design heritage, the LIS results indicate that GLM may also experience stable performance over its lifetime.

Buechler, D. E.↗
NASA NTRS1976

LUMIS Interactive graphics operating instructions and system specifications

The LUMIS program has designed an integrated geographic information system to assist program managers and planning groups in metropolitan regions. Described is the system designed to interactively interrogate a data base, display graphically a portion of the region enclosed in the data base, and perform cross tabulations of variables within each city block, block group, or census tract. The system is designed to interface with U. S. Census DIME file technology, but can accept alternative districting conventions. The system is described on three levels: (1) introduction to the systems's concept and potential applications; (2) the method of operating the system on an interactive terminal; and (3) a detailed system specification for computer facility personnel.

Bryant, N. A.↗
NASA NTRS1979

The application of microprocessor technology to in-flight computation

A modular design of a general purpose microprocessor-based computer to perform in-flight computations for cross-country soaring pilots is described. The basic requirements for the system are discussed. Several specialized applications of the computer are presented, including real-time pilot feedback and flight-test data acquisition and reduction.

Sawyer, P. L.↗
NASA NTRS1980

Cryogenic cooling study for the advanced limb scanner

The cryogenic operating requirements for a VM refrigerator to be used for detector cooling of the advanced limb scanner (ALS) instrument are defined. Determination of these requirements include consideration of mission and environmental constraints. Based on the operating requirements a detailed refrigerator design and performance analysis is conducted resulting in an optimized VM refrigerator conceptual design. The cooler-instrument-spacecraft interfaces are evaluated resulting in recommendations as to the best approach and most effective concepts resulting in simple and satisfactory interfaces. A preliminary implementation plan and schedule describing the general tasks required to develop, design, manufacture, test, and deliver three VM coolers and required support equipment to support an ALS flight experiment are presented. The result of this effort shows that existing VM cooler technology is sufficient to satisfy ALS mission requirements and schedules.

Russo, S. C.↗
NASA NTRS1985

Prewhirl Jet Model

Simple accurate model of centrifugal or rocket engine pumps provides information necessary to design inducer backflow deflector, backflow eliminator and prewhirl jet in jet mixing zones. Jet design based on this model shows improvement in inducer suction performance and reduced cavitation damage.

Meng, S. Y.↗
NASA NTRS1985

Shuttle Communications and Tracking Systems Modeling and TDRSS Link Simulations Studies

An analytical simulation package (LinCsim) which allows the analytical verification of data transmission performance through TDRSS satellites was modified. The work involved the modeling of the user transponder, TDRS, TDRS ground terminal, and link dynamics for forward and return links based on the TDRSS performance specifications (4) and the critical design reviews. The scope of this effort has recently been expanded to include the effects of radio frequency interference (RFI) on the bit error rate (BER) performance of the S-band return links. The RFI environment and the modified TDRSS satellite and ground station hardware are being modeled in accordance with their description in the applicable documents.

Chie, C. M.↗
NASA NTRS1986

Liquid helium cooled Fabry-Perot spectrometers

An account is given of two successful efforts to construct cryogenic Fabry-Perot interferometers that are sufficiently compact and stable for such harsh conditions as those of balloon or space observations, as well as ground-based ones. Attention is given to the design features and performance of a Fabry-Perot interferometer incorporating an electromagnet actuator, the ISAS interferometer, a Fabry-Perot spectrometer with superconducting actuators, and the University of Arizona interferometer.

Okuda, H.↗