Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “parametric study”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

A hybrid airship concept for Naval missions

A preliminary analysis of a hybrid semibuoyant delta-planform airship was performed using a computer synthesis program. The delta-planform hull shape was studied parametrically to determine the effects on vehicle performance for two Navy antisubmarine missions. The effects of buoyancy ratio, design speed, and altitude were also studied. The results suggest that long-range mission vehicles require a near buoyant or fully buoyant design and that there is no special advantage to the use of a lifting-body hull shape. For shorter-range missions, hybrid vehicles may have merit, and optimum vehicle buoyancy varies depending on whether a minimum-weight or minimum-fuel-consumption design is desired. As compared with conventionally shaped airships, the benefits, if any, from a lifting-body configuration will be limited to missions requiring relatively higher flight speeds.

Harper, M.↗
NASA NTRS1989

An analytical and experimental investigation of edge delamination in laminates subjected to tension, bending, and torsion

An integrated two-dimensional finite element was developed to calculate interlaminar stresses and strain energy release rates for the study of delamination in composite laminates subjected to uniaxial tension, bending, and torsion loads. Addressed are the formulation, implementation, and verification of the model. Parametric studies were conducted on the effect of Poisson's ratio mismatch between plies and the stacking sequence on interlaminar stress, and on the effect of delamination opening height and delamination length, due to bending, on strain energy release rate for various laminates. A comparison of strain energy release rates in all-graphite and graphite/glass hybrid laminates is included. The preliminary results of laminates subjected to torsion are also included. Fatigue tension tests were conducted on Mode 1 and mixed mode edge-delamination coupons to establish the relationship between fatigue load vs. onset of delamination cycle. The effect on the fatigue delamination onset of different frequencies (1 and 5 Hz) was investigated for glass, graphite,and their hybrid laminates. Although a 20 percent increase in the static onset-of-delamination strength and a 10 percent increase in ultimate strength resulted from hybridizing the all-graphite laminate with a 90 deg glass ply, the fatigue onset is lower in the hybrid laminate than in the all-graphite laminate.

Chan, Wen S.↗
NASA NTRS1989

A model for compression after impact strength evaluation

One key property commonly used for evaluating composite material performance is compression after impact strength (CAI). Standarad CAI tests typically use a specific laminate stacking sequence, coupon geometry, and impact level. In order to understand what material factors affect CAI, evaluation of test results should include more than comparisons of the measured strength for different materials. This study considers the effects of characteristic impact damage state, specimen geometry, material toughness, ply group thickness, undamaged strength, and failure mode. The results of parametric studies, using an analysis model developed to predict CAI, are discussed. Experimental results used to verify the model are also presented. Finally, recommended pre- and post-test CAI evaluation schemes which help link material behavior to structural performance are summarized.

Ilcewicz, Larry B.↗
NASA NTRS1990

Experimental and analytical evaluation of efficiency of helicopter planetary stage

The efficiency of a helicopter transmission planetary stage was studied both experimentally and analytically. Experiments were done by using a back-to-back, test-and-slave arrangement. The experiments were a parametric study of the effects of operating conditions on efficiency. In order to enhance the analysis, a model was developed that calculates the power required for the meshing gears to displace oil trapped between the gear teeth. In general, the analysis predicted higher efficiencies than were measured. The results of this study were compared with those of other studies.

Krantz, Timothy L.↗
NASA NTRS2008

Combustion Devices CFD Team Analyses Review

A variety of CFD simulations performed by the Combustion Devices CFD Team at Marshall Space Flight Center will be presented. These analyses were performed to support Space Shuttle operations and Ares-1 Crew Launch Vehicle design. Results from the analyses will be shown along with pertinent information on the CFD codes and computational resources used to obtain the results. Six analyses will be presented - two related to the Space Shuttle and four related to the Ares I-1 launch vehicle now under development at NASA. First, a CFD analysis of the flow fields around the Space Shuttle during the first six seconds of flight and potential debris trajectories within those flow fields will be discussed. Second, the combusting flows within the Space Shuttle Main Engine's main combustion chamber will be shown. For the Ares I-1, an analysis of the performance of the roll control thrusters during flight will be described. Several studies are discussed related to the J2-X engine to be used on the upper stage of the Ares I-1 vehicle. A parametric study of the propellant flow sequences and mixture ratios within the GOX/GH2 spark igniters on the J2-X is discussed. Transient simulations will be described that predict the asymmetric pressure loads that occur on the rocket nozzle during the engine start as the nozzle fills with combusting gases. Simulations of issues that affect temperature uniformity within the gas generator used to drive the J-2X turbines will described as well, both upstream of the chamber in the injector manifolds and within the combustion chamber itself.

Rocker, Marvin↗
NASA NTRSDate not supplied

Time-Frequency Analysis of Experimental and Analytical Hub Loads of a Rotor Undergoing a Rotor Speed Change

A two-part analytical study was conducted examining a small-scale, two-bladed rotor undergoing a change in rotor speed in a wind tunnel setting. First, a parametric study was conducted to understand how rotor transient response, determined using a time-marching solution, is affected by the choice of rotor wake model, blade elasticity, and inclusion of an elastic support structure model. The second part of the study compared results from an analytical model of the NASA Multirotor Test Bed (MTB) undergoing a rotor speed change to experimental data. Since the analytical and experimental time histories were non-stationary signals, a Stockwell transform was employed to analyze the data in lieu of traditional Fourier transform-based methods. The analysis included extraction of time-varying frequency content of the rotor thrust and hub motion, damping ratios, instantaneous rotor speed, and instantaneous phase difference between thrust and hub motion. Use of a free wake model was found to be necessary to predict higher-harmonic thrust, however, it underpredicted the amplitude of the unsteady loads. Modeling the elasticity of the stiff rotor blades installed on the MTB resulted in minimal impact on the vibratory loads compared to a rigid blade model. The current analytical model of the MTB, including an elastic support structure, properly predicted the measured trends in the frequency content of the thrust.

Rotor dynamics↗
NASA NTRS1980

Gallium arsenide (GaAs) solar cell modeling studies

Various models were constructed which will allow for the variation of system components. Computer studies were then performed using the models constructed in order to study the effects of various system changes. In particular, GaAs and Si flat plate solar power arrays were studied and compared. Series and shunt resistance models were constructed. Models for the chemical kinetics of the annealing process were prepared. For all models constructed, various parametric studies were performed.

Heinbockel, J. H.↗
NASA NTRS1987

Structural design of an in-line bolted joint for the space shuttle solid rocket motor case segments

Results of a structural design study of an in-line bolted joint concept which can be used to assemble Space Shuttle Solid Rocket Motor (SRM) case segments are presented. Numerous parametric studies are performed to characterize the in-line bolted joint behavior as major design variables are altered, with the primary objective always being to keep the inside of the joint (where the O-rings are located) closed during the SRM firing. The resulting design has 180 1-inch studs, an eccentricity of -0.5 inch, a flange thickness of 3/4 inch, a bearing plate thickness of 1/4 inch, and the studs are subjected to a preload which is 70% of ultimate. The mass penalty per case segment joint for the in-line design is 346 lbm more than the weight penalty for the proposed capture tang fix.

Dorsey, John T.↗
NASA NTRS1988

An improved boundary force method for analyzing cracked anisotropic materials

The Boundary Force Method (BFM), a form of indirect boundary element method, is used to analyze composite laminates with cracks. The BFM uses the orthotropic elasticity solution for a concentrated horizontal and vertical force and a moment applied at a point in a cracked, infinite sheet as the fundamental solution. The necessary stress functions for this fundamental solution were formulated using the complex variable theory of orthotropic elasticity. The current method is an improvement over a previous method using only forces and no moment. The improved method was verified by comparing it to accepted solutions for a finite-width, center-crack specimen subjected to uniaxial tension. Four graphite/epoxy laminates were used: (0 + or - 45/90)sub s, (0), (+ or - 45)sub s, and (+ or - 30)sub s. The BFM results agreed well with accepted solutions. Convergence studies showed that with the addition of the moment in the fundamental solution, the number of boundary elements required for a converged solution was significantly reduced. Parametric studies were done for two configurations for which no orthotropic solutions are currently available; a single edge crack and an inclined single edge crack.

Tan, Paul W.↗
NASA NTRS1989

An improved boundary force method for analysing cracked anisotropic materials

The Boundary Force Method (BFM), a form of indirect boundary element method, is used to analyze composite laminates with cracks. The BFM uses the orthotropic elasticity solution for a concentrated horizontal and vertical force and a moment applied at a point in a cracked, infinite sheet as the fundamental solution. The necessary stress functions for this fundamental solution were formulated using the complex variables theory of orthotropic elasticity. The current method is an improvement over a previous method using only forces and no moment. The improved method was verified by comparing it to accepted solutions for a finite-width, center-crack specimen subjected to uniaxial tension. Four graphite/epoxy laminates were used: (0 + or - 45/90)sub s, (0), (+ or - 45)sub s, and (+ or - 30)sub s. The BFM results agreed well with accepted solutions. Convergence studies showed that with the addition of the moment in the fundamental solution, the number of boundary elements required for a converged solution was significantly reduced. Parametric studies were done for two configurations for which no orthotropic solutions are currently available; a single edge crack and an inclined single edge crack.

Tan, P. W.↗
NASA NTRS1991

Wind tunnel blockage study of a generic three-dimensional sidewall compression scramjet inlet at Mach 10

A large scale model of a generic three-dimensional sidewall compression scramjet inlet has been designed based on the results of a computational parametric study for testing in the 31-inch Mach 10 Hypersonic Wind Tunnel at the NASA Langley Research Center. In order to increase the instrumentation density in interaction regions for a highly instrumented model, it is desirable to make the model as large as possible. When the cross-sectional area of a model becomes large relative to the inviscid core size of the tunnel, the effects of blockage must be considered. In order to assess these effects, a blockage model (an inexpensive, much less densely instrumented version of the configuration) was fabricated for preliminary testing. Since it was desired to determine both the effect of the model on the performance of the wind tunnel and also to determine if the inlet would start, the model possessed a total of 32 static pressure orifices distributed on the forebody plane and sidewalls; seventeen static pressure orifices on the tunnel wall and 3 pitot probes on the model monitored the tunnel performance. This paper presents the design considerations in the development of the wind tunnel model and the blockage aspects of the effects of contraction ratio, cowl location, Reynolds number, and angle of attack.

Holland, Scott D.↗
NASA NTRS1977

A simulation of air pollution model parameter estimation using data from a ground-based LIDAR remote sensor

One way to obtain estimates of the unknown parameters in a pollution dispersion model is to compare the model predictions with remotely sensed air quality data. A ground-based LIDAR sensor provides relative pollution concentration measurements as a function of space and time. The measured sensor data are compared with the dispersion model output through a numerical estimation procedure to yield parameter estimates which best fit the data. This overall process is tested in a computer simulation to study the effects of various measurement strategies. Such a simulation is useful prior to a field measurement exercise to maximize the information content in the collected data. Parametric studies of simulated data matched to a Gaussian plume dispersion model indicate the trade offs available between estimation accuracy and data acquisition strategy.

Kibler, J. F.↗
NASA NTRS1985

A consideration of atomic oxygen interactions with space station

A computer model is developed in order to calculate fluence for a generalized spacecraft in orbital flight based on mass spectrometer and incoherent scatter (MSIS) measurements of ambient density. The calculations are used to identify criteria for the selection of materials for the construction of an LEO Space Station. The model is generalized such that the surfaces for study can be oriented in any direction with respect to: a body coordinate system fixed to the spacecraft (E surfaces); and a solar inertial coordinate system. A parametric study was performed in order to evaluate the effects of altitude, inclination, and solar activity on atomic oxygen fluence. Values are obtained for samples of Mylar, Kevlar, Kapton, Tedlar, Teflon and sulfone, as well as for some ethylene polymers. The range of values for material reactivities is from 360 microns for ram-facing surfaces to 200 microns for solar power surfaces during each cycle of solar activity. The possibility of improving reactivity by employing certain chemical coatings is also discussed.

Leger, L. J.↗
NASA NTRS1989

Synthetic perspective optical flow: Influence on pilot control tasks

One approach used to better understand the impact of visual flow on control tasks has been to use synthetic perspective flow patterns. Such patterns are the result of apparent motion across a grid or random dot display. Unfortunately, the optical flow so generated is based on a subset of the flow information that exists in the real world. The danger is that the resulting optical motions may not generate the visual flow patterns useful for actual flight control. Researchers conducted a series of studies directed at understanding the characteristics of synthetic perspective flow that support various pilot tasks. In the first of these, they examined the control of altitude over various perspective grid textures (Johnson et al., 1987). Another set of studies was directed at studying the head tracking of targets moving in a 3-D coordinate system. These studies, parametric in nature, utilized both impoverished and complex virtual worlds represented by simple perspective grids at one extreme, and computer-generated terrain at the other. These studies are part of an applied visual research program directed at understanding the design principles required for the development of instruments displaying spatial orientation information. The experiments also highlight the need for modeling the impact of spatial displays on pilot control tasks.

Bennett, C. Thomas↗
NASA NTRS1992

PAYCOS, a multidisciplinary sizing code for hypersonic vehicles

PAYCOS is a computer code developed to rapidly perform concept sizing, concept evaluation, and associated trade studies for supersonic and hypersonic maneuvering vehicles. PAYCOS is a multidisciplinary analysis code that allows the engineer to determine the best geometric configuration for each design through parametric studies and mathematical optimization. This paper presents a general overview of the code, including a brief discussion of the approach used to develop it. The modular structure of the code is reviewed, and a brief discussion of each module is presented. Input data needed to run the code and output data supplied by it are discussed. The role of mathematical optimization in the solution process is discussed in some detail and examples of this process are presented. Finally, current modifications to the code are described along with potential future modifications and applications.

Edington, Larry↗
NASA NTRS1972

Analysis of oil lubricated, fluid film, thrust bearings with allowance for temperature dependent viscosity

A preliminary design study was performed to seek a fluid-film thrust bearing design intended to be part of a high-speed, hybrid (rolling element/fluid film) bearing configuration. The base line used is a design previously tested. To improve the accuracy of theoretical predictions of load capacity, flow rate, and friction power loss, an analytical procedure was developed to include curvature effects inherent in thrust bearings and to allow for the temperature rise in the fluid due to viscous heating. Also, a narrow-groove approximation in the treatment of the temperature field was formulated to apply the procedure to the Whipple thrust bearing. A comparative trade-off study was carried out assuming isothermal films; its results showed the shrouded-step design to be superior to the Whipple design for the intended application. An extensive parametric study was performed, employing isoviscous calculations, to determine the optimized design, which was subsequently recalculated allowing for temperature effects.

Pan, C. H. T.↗
NASA NTRS1976

Technical and economic assessment of span-distributed loading cargo aircraft concepts

A preliminary design study of the performance and economics resulting from the application of the distributed load concept to large freighter aircraft was made. The study was limited to configurations having the payload entirely contained in unswept wings of constant chord with conventional tail surfaces supported from the wing by twin booms. A parametric study based on current technology showed that increases in chord had a similar effect on the economics as increases in span. Increases in both span and chord or airplane size had the largest and most favorable effect. At 600,000 lbs payload a configuration was selected and refined to incorporate advanced technology that could be in production by 1990 and compared with a reference conventional airplane having similar technology.

Whitlow, D. H.↗