SEARCH · Engineering Papers

Results for “parametric study”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

All sources NASA NTRS DOE OSTI

NASA NTRS1978

A parametric experimental study of the slotted-wall boundary condition

An experimental study of slotted upper and lower walls in a two dimensional transonic wind tunnel with solid sidewalls is reported. Results are presented for several slot spacings and slot openness ratios. The experimental data were pressure measurements which were made on an airfoil model and on a sidewall near one of the slotted walls. The slotted-wall boundary condition coefficient, which related the pressure and streamline curvature near the wall, was determined from the wall pressure measurements. The measured wall-induced interference was correlated with the experimental values for the boundary condition coefficient. This correlation was compared with theory.

Everhart, J. L.↗

NASA NTRS1981

Parametric Analytical Studies for the Nonlinear Dynamic Response of the Tile/Pad Space Shuttle Thermal Protection System

The studies examined for imposed sinusoidal and random motions of the shuttle skin and/or applied tile pressure. Studies are performed using the computer code DYNOTA which takes into account the highly nonlinear stiffening hysteresis and viscous behavior of the pad joining the tile to the shuttle skin. Where available, experimental data are used to confirm the validity of the analysis. Both analytical and experimental studies reveal that the system resonant frequency is very high for low amplitude oscillations but decreases rapidly to a minimum value with increasing amplitude.

Edighoffer, H.↗

NASA NTRS1986

Parametric analytical study of instability-related delamination growth

The effect of various parameters on instability-related delamination growth was studied analytially. The configuration studied consisted of a thick composite laminate with a single through-width delamination located near one surface. Both mechanical and thermal loads were considered. All conclusions were based on the assumption that GI and GII govern delamination growth. An approximate superposition stress analysis was developed which gives closed form expressions for GI and GII. The simplicity of the analysis permitted examination of numerous configurations. Both GI and GII were found to be very sensitive to delamination length and location through the thickness. The magnitude of GI was also very sensitive to initial imperfections, which might be the results of an inclusion of finite thickness in the delamination. Critical loads for delamination growth were calculated based on three growth criteria. Large differences in the predictions highlight the need for a verified mixed-mode delamination growth criterion.

Whitcomb, J. D.↗

NASA NTRS1992

A Parametric Numerical Study of Mixing in a Cylindrical Duct

The interaction is described of some of the important parameters affecting the mixing process in a quick mixing region of a rich burn/quick mix/lean burn (RQL) combustor. The performance of the quick mixing region is significantly affected by the geometric designs of both the mixing domain and the jet inlet orifices. Several of the important geometric parameters and operating conditions affecting the mixing process were analytically studied. Parameters such as jet-to-mainstream momentum flux ratio (J), mass flow ratio (MR), orifice geometry, orifice orientation, and number of orifices/row (equally spaced) around the circumferential direction were analyzed. Three different sets of orifice shapes were studied: (1) square, (2) elongated slots, and (3) equilateral triangles. Based on the analytical results, the best mixing configuration depends significantly on the penetration depth of the jet to prevent the hot mainstream flow from being entrained behind the orifice. The structure in a circular mixing section is highly weighted toward the outer wall and any mixing structure affecting this area significantly affects the overall results. The increase in the number of orifices per row increases the mixing at higher J conditions. Higher slot slant angles and aspect ratios are generally the best mixing configurations at higher momentum flux ratio (J) conditions. However, the square and triangular shaped orifices were more effective mixing configurations at lower J conditions.

Oechsle, V. L.↗

NASA NTRS1992

A parametric numerical study of mixing in a cylindrical duct

The interaction is described of some of the important parameters affecting the mixing process in a quick mixing region of a rich burn/quick mix/lean burn (RQL) combustor. The performance of the quick mixing region is significantly affected by the geometric designs of both the mixing domain and the jet inlet orifices. Several of the important geometric parameters and operating conditions affecting the mixing process were analytically studied. Parameters such as jet-to-mainstream momentum flux ratio (J), mass flow ratio (MR), orifice geometry, orifice orientation, and number of orifices/row (equally spaced around the circumferential direction were analyzed. Three different sets of orifice shapes were studied: (1) square, (2) elongated slots, and (3) equilateral triangles. Based on the analytical results, the best mixing configuration depends significantly on the penetration depth of the jet to prevent the hot mainstream flow from being entrained behind the orifice. The structure in a circular mixing section is highly weighted toward the outer wall and any mixing structure affecting this area significantly affects the overall results. The increase in the number of orifices per row increases the mixing at higher J conditions. Higher slot slant angles and aspect ratios are generally the best mixing configurations at higher momentum flux ratio (J) conditions. However, the square and triangular shaped orifices were more effective mixing configurations at lower J conditions.

Oechsle, V. L.↗

NASA NTRS1991

Proposed CTV design reference missions in support of Space Station Freedom

Use of design reference missions (DRM's) for the cargo transfer vehicle (CTV) in support of Space Station Freedom (SSF) can provide a common baseline for the design and assessment of CTV systems and mission operations. These DRM's may also provide baseline operations scenarios for integrated CTV, Shuttle, and SSF operations. Proposed DRM's for CTV, SSF, and Shuttle operations envisioned during the early post-PMC time frame and continuing through mature, SSF evolutionary operations are described. These proposed DRM's are outlines for detailed mission definition; by treating these DRM's as top-level input for mission design studies, a range of parametric studies for systems/operations may be performed. Shuttle flight design experience, particularly rendezvous flight design, provides an excellent basis for DRM operations studies. To begin analysis of the DRM's, shuttle trajectory design tools were used in single case analysis to define CTV performance requirements. A summary of these results is presented.

Saucillo, Rudy J.↗

NASA NTRS1999

Parametric Experimental Study of the Formation of Glaze Ice Shapes on Swept Wings

An experiment was conducted to study the effect of velocity and sweep angle on the critical distance in ice accretion formation on swept wings at glaze ice conditions. The critical distance is defined as the distance from the attachment line to the beginning of the zone where roughness elements develop into glaze ice feathers. Icing runs were performed on a NACA 00 1 2 swept wing tip at velocities of 75, 100, 150, and 200 miles per hour. At each velocity and tunnel condition, the sweep angle was changed from 0 deg to 45 deg at 5 deg increments. Casting data, ice shape tracings, and close-up photographic data were obtained. The results showed that at given velocity and tunnel conditions, as the sweep angle is increased from 0 deg to 25 deg the critical distance slowly decreases. As the sweep angle is increased past 25 deg, the critical distance starts decreasing more rapidly. For 75 and 100 mph it reaches a value of 0 millimeters at 35 deg. For 150 and 200 mph it reaches a value of 0 millimeters at 40 deg. On the ice accretion, as the sweep angle is increased from 0 deg to 25 deg, the extent of the attachment line zone slowly decreases. In the glaze ice feathers zone, the angle that the preferred direction of growth of the feathers makes with respect to the attachment line direction increases. But overall, the ice accretions remain similar to the 0 deg sweep angle case. As the sweep angle is increased above 25 deg, the extent of the attachment line zone decreases rapidly and complete scallops form at 35 deg sweep angle for 75 and 100 mph, and at 40 deg for 150 and 200 mph.

Vargas, Mario↗

DOE OSTI2023

A parametric finite element study for determining burst strength of thin and thick-walled pressure vessels

To accurately predict the burst strength of both thin and thick-walled pressure vessels (PVs), a parametric study of PV burst strength was performed for a wide range of vessel geometries and materials using elastic-plastic finite element analysis (FEA). A valid FEA model was established through a detailed study of 2D versus 3D FEA models, the critical stress failure criterion versus the limit load criteria, and the thick-wall effect on the FEA simulations. Here, the results show that the stresses and strains at the mean diameter, rather than outside diameter, determines a more accurate burst strength for both thin and thick-walled PVs. On this basis, a parametrized FEA script using the ABAQUS Python application programming interface (API) was used to create a large database of PV burst strengths for a variety of vessel geometries and materials, demonstrating that Python scripting is a powerful technique for performing parametric studies or generating large databases. From the FEA results, using the regression method, a new burst pressure model was developed as a function of the vessel geometry (D/t ratio) and material properties (UTS and n). As validated by a large number of full-scale burst test data, the proposed burst model can very accurately predict the burst strength for both thin and thick-walled PVs.

42 ENGINEERING↗

DOE OSTI2022

Influence of cementation on the yield surface of rocks numerically determined from digital microstructures

Digital Rock Physics has reached a level of maturity on the characterisation of primary properties that depend on the microstructure – such as porosity, permeability or elastic moduli – by numerically solving field equations on μCT scan images of rock. After small deformations or at depth though, most rocks eventually reach their limit of elasticity and the complementary plastic properties are needed to describe the full mechanical behaviour. Currently, determination of a rock’s yield surface from its microstructure is often restricted to semi-analytical criteria derived by limit analysis or numerical simulations performed on idealised geometries. Such simplification lacks representativeness, particularly for processes that affect directly the pore-grain interface such as the cementation phenomenon, happening during diagenesis. Eventually, only direct numerical simulation of elasto-plasticity performed on digitalised microstructures can be used to assess the strength of different cemented materials and its evolution with the alteration of the microstructure. In this study, we provide a comprehensive parametric study on the impact of cementation on rock strength for real microstructures of cemented granular materials. Compared to most previous studies, the whole yield surface is determined numerically (using Finite Element Method) in order to assess the influence of cementation for different stress-paths. The previously known tendency of rock to strengthen with increasing cementation volume is verified. New results on the influence of cement property namely Young’s modulus, friction and cohesion on the rock’s yield surface are explored. The envelopes obtained are compared to the ones obtained by experimental data and existing models. Finally, the framework presented in this study showcases the wider possibility of determining any rock’s or porous material’s yield surface from its microstructure.

36 MATERIALS SCIENCE↗

NASA NTRS2002

Quasi-One-Dimensional Modeling of Pulse Detonation Rocket Engines

Pulsed detonation rocket engines (PDREs) have generated considerable research interest in recent years as a chemical propulsion system potentially offering improved performance and reduced complexity compared to conventional rocket engines. The detonative mode of combustion employed by these devices offers a thermodynamic advantage over the constant-pressure deflagrative combustion mode used in conventional rocket engines and gas turbines. However, while this theoretical advantage has spurred a great deal of interest in building PDRE devices, the unsteady blowdown process intrinsic to the PDRE has made realistic estimates of the actual propulsive performance problematic. The recent review article by Kailasanath highlights some of the difficulties in comparing the available experimental measurements with numerical models. In a previous paper by the author, parametric studies of the performance of a single, straight-tube PDRE were reported. A 1-D, unsteady method of characteristics code, employing a constant-gamma assumption behind the detonation front, was developed for that study. Models of this type are computationally inexpensive, and are particularly useful for parametric performance comparisons. For example, a plot showing the specific impulse of various PDRE and steady-state rocket engine (SSRE) configurations as a function of blowdown pressure ratio. The performance curves clearly indicate that a straight-tube PDRE is superior in specific impulse to a SSRE with a sonic nozzle over the entire range of pressure ratios. Note, however, that a straight-tube PDRE in general does not compare favorably to a SSRE fitted with an optimized de Laval supersonic nozzle, particularly at the high pressure ratios typical for boost or in-space rocket applications. However, the calculations also show that if a dynamically optimized, supersonic de Laval nozzle could be could be fitted to a PDRE, then the specific impulse of the device would exceed that of a comparable SSRE. While such a nozzle is a considerable idealization, it is clear that nozzle design and optimization will play a critical role in whether the performance potential of PDREs can be effectively realized in practice. In order to study PDRE nozzle issues with greater accuracy, a quasi-one-dimensional, finite-rate chemistry CFD code has been developed by the author. Comparisons of the code with both the previous MOC model and experimental data from Stanford University are reported. The effect of constant-gamma and finite-rate chemistry assumptions on the flowfield and performance is examined. Parametric studies of the effect of nozzle throat size and expansion ratio, at various blowdown pressure ratios, are reported.

Morris, Christopher I.↗

NASA NTRS1991

Analytical study of nozzle performance for nuclear thermal rockets

A parametric study has been conducted by the NASA-Lewis Rocket Engine Design Expert System for the convergent-divergent nozzle of the Nuclear Thermal Rocket system, which uses a nuclear reactor to heat hydrogen to high temperature and then expands it through the nozzle. It is established by the study that finite-rate chemical reactions lower performance levels from theoretical levels. Major parametric roles are played by chamber temperature and chamber pressure. A maximum performance of 930 sec is projected at 2700 K, and of 1030 at 3100 K.

Davidian, Kenneth O.↗

NASA NTRS2011

Advanced Technology Subsonic Transport Study: N+3 Technologies and Design Concepts

Conceptual Research Corporation, the Science of the Possible, has completed a two-year study of concepts and technologies for future airliners in the 180-passenger class. This NASA-funded contract was primarily focused on the ambitious goal of a 70 percent reduction in fuel consumption versus the market-dominating Boeing 737-800. The study is related to the N+3 contracts awarded in 2008 by NASA s Aeronautics Research Mission Directorate to teams led by Boeing, GE Aviation, MIT, and Northrop Grumman, but with more modest goals and funding. CRC s contract featured a predominant emphasis on propulsion and fuel consumption, but since fuel consumption depends upon air vehicle design as much as on propulsion technology, the study included notional vehicle design, analysis, and parametric studies. Other NASA goals including NOx and noise reduction are of long-standing interest but were not highlighted in this study, other than their inclusion in the propulsion system provided to CRC by NASA. The B-737-800 was used as a benchmark, parametric tool, and design point of departure. It was modeled in the RDS-Professional aircraft design software then subjected to extensive parametric variations of parasitic drag, drag-due-to-lift, specific fuel consumption, and unsized empty weight. These studies indicated that the goal of a 70 percent reduction in fuel consumption could be attained with roughly a 30 percent improvement in all four parameters. The results were then fit to a Response Surface and coded for ease of use in subsequent trade studies. Potential technologies to obtain such savings were identified and discussed. More than 16 advanced concept designs were then prepared, attempting to investigate almost every possible emerging concept for application to this class airliner. A preliminary assessment of these concepts was done based on their total wetted area after design normalization of trimmed maximum lift. This assessment points towards a Tailless Airliner concept which was designed and analyzed in some detail. To make it work, a retracting canard and an all-moving chin rudder were employed, along with the use of the Active Aeroelastic Wing technology. Results indicate that a 60 percent savings in fuel burn may be credibly attained, but this depends upon a lot of technology maturation, concept development, and risk reduction. This should be expected-such a dramatic reduction in fuel consumption is a "game changer" in the world of commercial aviation. It won t be easy.

Raymer, Daniel P.↗

DOE OSTI2023

Electropolishing parameters study for surface smoothening of low-$\beta$650 MHz five-cell niobium superconducting radio frequency cavity

Electropolishing (EP) is applied to niobium (Nb) superconducting radio frequency (SRF) cavities, which are used in particle accelerators for their surface treatment. The EP process for 1.3 GHz cavities has been extensively studied earlier. In this work, a parametric study on EP of low-β (0.61) 650 MHz Nb SRF cavities (LB650), which will be used in pre-production cryomodule for proton improvement plan-II (PIP-II) linear accelerator, was conducted to determine adequate EP conditions for attaining a smooth surface of the cavities. EP performed with the standard parameters and an initial cathode (cathode-I) having a cathode surface area of ~5% of the cavity surface area yielded a rough equator surface of the cavity. The grain step height on the equator weld position was measured to be ~ 32 μm. The rough surface was attributed to preferential grain etching confirmed by a polarization curve showing a linear relationship between the EP current and voltage and the absence of the current plateau region. The cathode was modified to make its surface area twice that of cathode-I. The modified cathode (cathode-M) provided a current plateau region in the corresponding I-V curves measured at different cavity temperatures. The onset voltage for the plateau was found to be higher at higher cavity temperatures. Here this study revealed that even with cathode-M, the standard 18 V was low for EP of such large-sized cavities when the cavity temperature was 18 °C. EP performed at a higher voltage of 22–24.5 V with cathode-M yielded a smooth surface with a grain step height of only 0.6 μm. The applied EP conditions also improved removal uniformity along the cavity length. In contrast to the cavity treated with cathode-I, the cavities treated with cathode-M achieved a significantly higher accelerating gradient (E acc ) in vertical tests conducted in a cryostat at 2 K. The modified EP was found efficient to produce the cavities that achieved E acc of 22.4 MV/m, required by PIP II project in the baseline RF tests, to qualify for further surface processing used to enhance their quality factors.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

NASA NTRS1993

Investigation of lunar base thermal control system options

Long duration human exploration missions to the Moon will require active thermal control systems which have not previously been used in space. The two technologies which are most promising for long term lunar base thermal control are heat pumps and radiator shades. Recent trade-off studies at the Johnson Space Center have focused development efforts on the most promising heat pump and radiator shade technologies. Since these technologies are in the early stages of development and many parameters used in the study are not well defined, a parametric study was done to test the sensitivity to each assumption. The primary comparison factor in these studies was the total mass system, with power requirements included in the form of a mass penalty for power. Heat pump technologies considered were thermally driven heat pumps such as metal hydride, complex compound, absorption and zeolite. Also considered were electrically driven Stirling and vapor compression heat pumps. Radiator shade concepts considered included step shaped, V-shaped and parabolic (or catenary) shades and ground covers. A further trade study compared the masses of heat pump and radiator shade systems.

Ewart, Michael K.↗

NASA NTRS2010

Optimizing a Laser Process for Making Carbon Nanotubes

A systematic experimental study has been performed to determine the effects of each of the operating conditions in a double-pulse laser ablation process that is used to produce single-wall carbon nanotubes (SWCNTs). The comprehensive data compiled in this study have been analyzed to recommend conditions for optimizing the process and scaling up the process for mass production. The double-pulse laser ablation process for making SWCNTs was developed by Rice University researchers. Of all currently known nanotube-synthesizing processes (arc and chemical vapor deposition), this process yields the greatest proportion of SWCNTs in the product material. The aforementioned process conditions are important for optimizing the production of SWCNTs and scaling up production. Reports of previous research (mostly at Rice University) toward optimization of process conditions mention effects of oven temperature and briefly mention effects of flow conditions, but no systematic, comprehensive study of the effects of process conditions was done prior to the study described here. This was a parametric study, in which several production runs were carried out, changing one operating condition for each run. The study involved variation of a total of nine parameters: the sequence of the laser pulses, pulse-separation time, laser pulse energy density, buffer gas (helium or nitrogen instead of argon), oven temperature, pressure, flow speed, inner diameter of the flow tube, and flow-tube material.

Arepalli, Sivaram↗

NASA NTRSDate not supplied

Continued Exploration of the Electrified Aircraft Propulsion Design Space

A previous electrified aircraft propulsion (EAP) design space exploration study was continued to investigate the impact of mission constraints, further explore the design space of different sized aircraft, and improve the modeling process. Three aircraft were investigated, 18- and 48-passenger turboprops, and a 78-passenger turbofan. Baseline aircraft models were inherited from the earlier study and were hybridized by applying EAP technologies. A parametric study varying motor power and battery specific energy was conducted. For the 78-passenger turbofan, design range was also introduced as a parametric parameter. Key metrics for the study included equivalent lifecycle CO2 emissions and direct operating cost plus interest. Both turboprop aircraft demonstrated significant potential savings in block fuel consumption and CO2 emissions, but at increased operating costs compared to their baseline models. As the 78-passenger turbofan had shown no improvements in any metrics under reasonable technology assumptions, design range was shortened in an attempt to obtain performance benefits. When designed for a shorter range, the 78-passenger EAP vehicle showed potential improvements in block fuel when compared to a baseline with a similarly shortened design range, but not in any other metrics. Operating cost reductions were not achieved for any aircraft, but several designs came close to breaking even with their baselines. Smaller, shorter range aircraft and turboprops demonstrated larger performance benefits and smaller operating cost penalties, but a simple trade of electric energy storage in batteries for fuel is generally insufficient to produce a viable aircraft concept.

Electrified Aircraft Propulsion↗

NASA NTRS1972

Studies of engine-airframe integrated hypersonic vehicles

A parametric study of an integrated airframe and engine is presented for a hypersonic transport at an altitude of 70,000 feet and a free stream Mach number of 6. The engine considered is a subsonic combustion ramjet using conventional hydrocarbon fuels. The lift-to-drag ratio of the aircraft for two configurations, one with full capture and accelerated flight and the other allowing spillage of the leading shock and in unaccelerated flight, is studied. The parameters varied are the engine efficiencies, the angle of attack, the combustion rates, as well as the captured mass flow. Lift-to-drag ratios on the order of 6.5 are obtained.

Saland, H.↗

DOE OSTI2021

Thermoeconomic Evaluation and Optimization of Using Different Environmentally Friendly Refrigerant Pairs for a Dual-Evaporator Cascade Refrigeration System

Applications of dual-evaporator refrigeration systems have recently gained much attention both in academia and industry due to their multiple benefits. In this study, a comprehensive thermodynamic and economic analysis is conducted to evaluate the potential of using several environmentally friendly refrigerant couples and identifies the most suitable one yielding the best economic results. To achieve this goal, a detailed parametric study is conducted, and an optimization process is performed using a particle swarm optimization (PSO) approach to minimize the unit production cost of cooling (UPCC) of the cascade refrigeration system. The results showed that among all selected 18 refrigerant pairs and for all ranges of examined operating parameters, the R170-R161 pair and R1150-R1234yf pair are identified as the best and worst pairs, respectively, from both thermodynamic and economic viewpoints. The results also confirm that R170-R161 pair has an improvement over R717-R744, used as a typical refrigerant pair of cascade refrigeration cycles. For a base case analysis, the COP of R170-R161 and R1150-R1234yf pairs is determined as 1.727 and 1.552, respectively, while their UPCC is found to be $0.395/ton-hr and $0.419/ton-hr, respectively, showing the influence of proper selection of refrigerant pairs on the cascade cycle’s performance. Overall, this study offers a useful thermodynamic and economic insight regarding the selection of proper refrigerant pairs for a dual-evaporator cascade vapor compression refrigeration system.

42 ENGINEERING↗