Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “microstructure model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

Simulating microgalvanic corrosion in alloys using the PRISMS phase-field framework

In this prospective paper, we first review the existing simulation tools to simulate microgalvanic corrosion during free immersion. Then, we describe a recently developed application that employs PRISMS-PF, an open-source, high-performance phase-field modeling framework. The model employed in the application accounts for the electrochemical reaction at the metal/electrolyte interface and ionic migration in the electrolyte to determine the evolution of the corrosion front. We present the implementation details for the application and discuss its features such as super-linear parallel scaling performance for a sufficiently large system. Finally, we demonstrate the capability of the application by simulating corrosion of the matrix phase of an alloy near a secondary phase particle in two and three dimensions.

36 MATERIALS SCIENCE↗

Development of an Open-source Alloy Selection and Lifetime Assessment Tool for Structural Components in CSP

Lack of sufficient data on high temperature mechanical and corrosion behavior of structural materials is a huge barrier in the technological maturity of current and future Concentrating Solar Power (CSP) technologies. Rapid development and selection of materials cannot be achieved by expensive and time-consuming acquisition of experimental data. The goal of the proposed work is development of an open-source alloy selection and lifetime prediction tool that will integrate validated physics-based models to describe influence of temperature, alloy composition, environment and component geometry (thickness) on mechanical and corrosion behavior of Ni and Fe-based alloys employed in molten salts/sCO 2 heat exchangers. This one-year project leveraged the extensive dataset on the creep\corrosion behavior of candidate materials generated at ORNL through past projects and input from current collaborations with industrial partners. Based on previous experience and the feedback provided by industry (Brayton Energy and Echogen), three candidate materials of interest, Ni-based alloys 740H, 282 and 625 and application-specific operating conditions (max. temperature of 730 °C and stress of 150 MPa) were identified for the heat exchanger. An extensive corrosion and creep dataset was assimilated for the relevant operating conditions and was supported by detailed characterization of about 100 metallographic cross-sections. The corrosion dataset consisted of scanning electron microscopy images (secondary electron and backscatter electron), measured concentration profiles of alloying elements using energy dispersive X-ray spectroscopy (EDS), widths of denuded zones (dissolution of strengthening phases) and depths of attack in molten KCl-MgCl 2 mixtures using image analyses. The creep dataset comprised of creep rupture data and creep strain curves (for 740H and 282). Coupled thermodynamic-kinetic microstructure-based models were employed to predict the stress-corrosion induced compositional and phase evolutions in the alloy during operation under the identified operating conditions. Reduced order models were developed from advanced physics-based models and were integrated in a user-friendly alloy selection tool. The corrosion model was able to predict the time to a critical Cr concentration at the oxide/alloy interface (chemical lifetime) within ±10% (1 standard deviation) of typical statistical variation in corrosion tests and EDS measurement errors (±0.5 wt%). The initial scope of the project was limited to predict creep rupture times (Larson-Miller parameter). Based on the input provided by industry, the mechanical lifetime of the heat exchanger is governed by accumulated creep strains (2%) rather than creep rupture. To be able to predict the times to specific creep strains, a more extensive creep model development was undertaken largely beyond the initial scope of the project. The continuum damage mechanics creep model was able to predict times to 2% creep strain, t 2% with an accuracy of ±500h. Ultimately, a screening protocol for SiC was generated to demonstrate the pathway for integration of one of the currently immature materials from a commercial adoption standpoint in the current material evaluation tool. The modeling tool developed here is accessible to the science community and stakeholders and lays the foundation for methods that will enable a rapid evaluation of optimum materials for CSP applications and reliable prediction of material degradation thereby considerably reducing operational costs, improving reliability and increasing overhaul intervals. However, the complete potential of such a tool to include a wider range of materials and test conditions can only be realized with a more concentrated combined experimental-characterization-computation effort.

14 SOLAR ENERGY↗

Predicting Failure Modes and Ductility of Dual Phase Steels Using Plastic Strain Localization

Ductile failure of metals is often treated as the result of void nucleation, growth and coalescence. Various criteria have been proposed to capture this failure mechanism for various materials. In this study, ductile failure of dual phase steels is predicted in the form of plastic strain localization resulting from the incompatible deformation between the harder marternsite phase and the softer ferrite matrix. Microstructure-level inhomogeneity serves as the initial imperfection triggering the instability in the form of plastic strain localization during the deformation process. Failure modes and ultimate ductility of two dual phase steels are analyzed using finite element analyses based on the actual steel microstructures. The plastic work hardening properties for the constituent phases are determined by the in-situ synchrotron-based high-energy X-ray diffraction technique. Under different loading conditions, different failure modes and ultimate ductility are predicted in the form of plastic strain localization. It is found that the local failure mode and ultimate ductility of dual phase steels are closely related to the stress state in the material. Under plane stress condition with free lateral boundary, one dominant shear band develops and leads to final failure of the material. However, if the lateral boundary is constrained, splitting failure perpendicular to the loading direction is predicted with much reduced ductility. On the other hand, under plane strain loading condition, commonly observed necking phenomenon is predicted which leads to the final failure of the material. These predictions are in reasonably good agreement with experimental observations.

36 MATERIALS SCIENCE↗

Laser processing

Progress in the Progress ceramic materials is reported. Experiments and models for sintering and microstructure evolution are described. Models and data for understanding the kinetics of grain boundary motion and of pore coarsening and new materials for fuel cells and batteries; are developed. New experimental techniques using lasers for forming fine, monosized powders and for forming stable and metastable structures from liquids, and solar materials research are also developed. Colloidal science and ceramics processing are explored; and research programs on the presintering science necessary for controlled green microstructures are outlined.

Source record↗

Modeling the role of local crystallographic correlations in microstructures of Ti-6Al-4V using a correlated structure visco-plastic self-consistent polycrystal plasticity formulation

This paper presents a multi-level crystal plasticity-based simulation framework for modeling mechanical response and microstructure evolution of Ti-6Al-4V with α-lath/lamellar microstructures. Here, the model is a correlated structure visco-plastic self-consistent (CS-VPSC) formulation linking three scales: a single crystals micro-scale, a lath/lamellar colony meso-scale, and a lath/lamellar aggregate macro-scale. A selected hardening law for the evolution of critical resolved shear stress per slip system used in CS-VPSC is phenomenological. However, it adjusts the resistances of basal and prismatic slip systems based on the geometry of slip transfer between adjacent lamellae. Consistent with experimental evidences, the resolved shear stress on the pyramidal slip planes is dependent not only on the stress in the direction of slip but also on the two orthogonal shear stress components and the three normal stress components (non-Schmid effects). Electron backscatter diffraction (EBSD) data in conjunction with a procedure relying on α→β phase transformation is used to construct paired variants of α-laths/lamellae satisfying their local crystallographic correlations. The procedure fits volume fractions of individual laths/lamellae with the experimental EBSD data and selects a distribution of habit planes between adjacent variants with respect to the loading direction. The simulation framework is applied to interpret the deformation behavior in tension and compression along two sample directions of Ti-6Al-4V fabricated via laser powder bed fusion. Moreover, the model is used to simulate texture evolution during rolling of the material to large strains. It is demonstrated that the model is capable of predicting plastic anisotropy/asymmetry and the concomitant texture evolution. While the model reveals a significant effect of habit plane inclination with respect to the loading direction on yield stress, the comparison of the data and model predictions shows that a random distribution of habit planes fits the flow response. It is further inferred that the tension-compression asymmetry arises from the non-Schmid effects.

36 MATERIALS SCIENCE↗

Micro–macro finite element modeling method for rub response in abradable coating materials

Gas turbine engines experience “rub” when the rotating blades come in contact with a static abradable coating. This results in extreme strain rates and dynamics inside a high-temperature/high-pressure environment. Current rub models are phenomenological and do not reflect the underlying microstructures, thus limiting their prediction accuracy. In this work, a microstructure-informed, reduced order modeling framework is introduced for simulating abradable coating “rub" behavior. This framework comprises a microscale model constructed based on digitized abradable microstructure and explicitly simulates the mechanical behavior of each constituent phases and their interactions. After calibration and validation with experiment data, the calibrated microscale model is used to generate data across a vast range of applied strain rates and temperature with various load paths. Then, the virtually generated data are used to fit the macroscopic-reduced order model, which enables fast component scale rub simulation without compromising the integrity of the complex material behavior. In conclusion, the proposed effort will address the technical challenge of predicting abradable material behavior during rub through the application of multiscale modeling from microstructure to engines behavior, effectively reducing the development costs and time of new abradable material for better “rub” properties.

36 MATERIALS SCIENCE↗

Effect of Anode Porosity and Temperature on the Performance and Lithium Plating During Fast-Charging of Lithium-Ion Cells

Twenty-four single-layer approximate to 32 mAh pouch cells are tested to determine the effect of electrode porosity on lithium plating. Twelve cells contain a graphite electrode that is 26% porous, and 47% for the other twelve. The cells are cycled using a 6-C charge and a C/2 discharge protocol at temperatures in the range of 20-50 degrees C. A macro-homogeneous electrochemical model and microstructure analysis tool set are used to help interpret experimental observations for the effect of anode porosity and ambient temperature on fast-charging performance. Additionally, comparison between the two also highlights gaps in current theoretical understanding that need to be addressed. In post-test examination, lithium plating is seen in all cells, regardless of porosity. Elevated temperature is shown to reduce the amount of lithium plating and improve initial fast-charge capacity, but also changes the rate of other, less well-understood degradation mechanisms. Apparent kinetic rate laws, At + Bt 1/2 , where A and B are constants, can be fit to most of the capacity loss and resistance increase data. The relative magnitudes of A and B change with temperature and porosity. The capacity loss data at 50 degrees C from the high-porosity cells are fit by a logistics rate law.

25 ENERGY STORAGE↗

Effects of Copper Content and Mold Temperature on the Hot Tearing Susceptibility of Mg-7Zn-xCu-0.6Zr Alloys

The effects of copper (Cu) content and mold temperature on the hot tearing susceptibility (HTS) of Mg-7Zn-xCu-0.6Zr (x = 0, 1, 2) alloys were investigated experimentally using a T-type hot tearing mold. The crack volumes were measured by paraffin permeation method, and the solidification process was analyzed by thermal analysis and by using the Clyne and Davies model. The microstructure and morphology of the crack zone of Mg-7Zn-xCu-0.6Zr alloys were characterized by scanning electron microscopy, and the composition of alloys was analyzed by X-ray diffraction. The results showed the formation of a new phase of MgZnCu in the alloys with Cu addition. Moreover, addition of Cu also led to the refinement of microstructures of Mg-7Zn-xCu-0.6Zr alloys. The HTS of Mg-7Zn-xCu-0.6Zr alloys decreased with the increase in both the content of Cu and the mold temperature.

36 MATERIALS SCIENCE↗

Evaluation of an Al-Ce alloy for laser additive manufacturing

Our present research in metal additive manufacturing (AM) focuses on designing processing parameters around existing alloys designed for traditional manufacturing. However, to maximize the benefits of AM, alloys should be designed to specifically take advantage of the unique thermal conditions of these processes. Furthermore, our study focuses on the development of a design methodology for alloys in AM, using a newly developed Al-Ce alloy as an initial case study. To evaluate the candidacy of this system for fusion based additive manufacturing, single-line laser melts were made on cast Al-12Ce plates using three different beam velocities (100, 200, and 300 mm/min). The microstructure was evaluated in the as-melted and heat treated conditions (24 hrs at 300°C). An extremely fine microstructure was observed within the weld pools, evolving from eutectic at the outer solid-liquid boundaries to a primary Al FCC dendritic/cellular structure nearer the melt-pool centerline. We rationalized the observed microstructures through the construction of a microstructure selection map for the Al-Ce binary system, which will be used to enable future alloy design. Interestingly, the heat treated samples exhibited no microstructural coarsening.

36 MATERIALS SCIENCE↗

Energetics of native defects, solute partitioning, and interfacial energy of Q precipitate in Al-Cu-Mg-Si alloys

The compound Al 3 Cu 2 Mg 9 Si 7 , is known as the Q-phase and forms as a thermodynamically stable precipitate during aging in the quaternary Al-Cu-Mg-Si system. We perform atomic-scale density functional theory (DFT) calculations of defect properties, solute partitioning, and interfacial stability of the Al 3 Cu 2 Mg 9 Si 7 (Q) precipitate. We find: (i) simple native point defect (i.e., vacancies and anti-sites) thermodynamics can partially explain the experimentally observed off-stoichiometry, such as the observed variation of compositions, Al 3+δ Cu 2 Mg 9-δ Si 7 (Mg-deficient and Al-rich) in experiment. (ii) Calculated solute-partitioning energies of common solutes allow us to define general rules for site-preference in the Q-phase in terms of electronic structure and atomic radius. To validate our DFT predictions, we perform atom-probe tomography (APT) experiments for six-different elements (Zn, Ni, Mn, Ti, V, and Zr). The results show that the partitioning behavior of solutes Ni, Zn, and Mn are consistent with DFT predictions, but the transition elements (Ti, V, and Zr), which are anomalously slow diffusers in Al, partition to the Q-phase in constrast to DFT partitioning energies. (iii) For the low energy interface ($11\bar{2}$) Q //(510) Al observed in needle shaped Q-precipitate, we survey various terminations and orientations and derive a low-energy interfacial structure. Here we find this low-energy interfacial model has Cu atoms nearest to the interface, which is in agreement with previous literature on Cu interfacial segregation at the Q'//α-Al interface. The computed interfacial energy (0.52 J/m 2 ) and the corresponding structure will be useful input to future multi-scale modeling of microstructural evolution.

36 MATERIALS SCIENCE↗

Crystallographic orientation and spatially resolved damage in a dispersion-hardened Al alloy

The in-situ neutron diffraction technique, in combination with both the full-field crystal elasto-viscoplastic finite element model and microstructural characterization, was used to study the deformation-induced damage anisotropy in a commercial Al alloy, subjected to uniaxial tensile and cyclic loading. The simulations capture well the crystallographic-orientation-dependent lattice strain behavior. The hard grains, e.g. those orientated with the <111> and <422> orientations parallel with the uniaxial loading direction (LD), feature large Taylor factors and seem more prone to form damage-related band structures. Their effective elastic moduli decrease with the accumulation of damage, which are different from the soft grains orientated with the <200> orientation along the LD. Correlation between the distribution of voids and that of the residual lattice strain developed after failure may exist. The maximum tensile type residual lattice strain observed after failure may be resulted from the band structure formed in the hardest <111> grains. It was revealed that the band structure triggered by the hard particles could be one of sources of damage. In addition, while the specimen was obviously damaged, a fast stress relief was evidenced after unloading from the tension, especially at the beginning of unloading. Our present investigations provide a novel method for exploring the damage mechanisms of polycrystalline materials during plastic deformation.

36 MATERIALS SCIENCE↗

Modeling char oxidation behavior under Zone II burning conditions at elevated pressures

For accurate modeling of the coal combustion process at elevated pressures, account must be made for variations in char-particle structure. As pressure is increased, particle swelling increases during the devolatilization of certain bituminous coals, yielding a variety of char-particle structures, from uniform high-density particles to thin-walled non-uniform low-density particles having large internal void volumes. Since under Zone II burning conditions the char conversion rate depends upon the accessibility of the internal surfaces, the char structure plays a key role in determining particle burnout times. In our approach to characterize the impact of char structure on particle burning rates, effectiveness factors appropriate for thin-walled cenospherical particles and thick-walled particles having a few large cavities are defined and related to the effectiveness factor for uniform high-density particles that have no large voids, only a random distribution of pores having a mean pore size in the sub-micron range. For the uniform case, the Thiele modulus approach is used to account for Zone 11 type burning in which internal burning is limited by the combined effects of pore diffusion and the intrinsic chemical reactivity of the carbonaceous material. In the paper, the impact of having a variety of char structures in a mix of particles burning under Zone II burning conditions is demonstrated.

01 COAL, LIGNITE, AND PEAT↗

Modeling of intragranular misorientation and grain fragmentation in polycrystalline materials using the viscoplastic self-consistent formulation

In this paper, the recently established methodology to use known algorithmic expressions of the second moments of the stress field in the grains of a polycrystalline aggregate for calculating average fluctuations of lattice rotation rates and the associated average intragranular misorientation distributions using the mean-field viscoplastic self-consistent (VPSC) formulation is extended to solve the coupled problem of considering the effect of intragranular misorientations on stress and rotation rate fluctuations. In turn, these coupled expressions are used to formulate and implement a grain fragmentation (GF) model in VPSC. Case studies, including tension and plane-strain compression of face-centered cubic polycrystals are used to illustrate the capabilities of the new model. GF-VPSC predictions of intragranular misorientation distributions and texture evolution are compared with experiments and full-field numerical simulations, showing good agreement. In particular, the inclusion of misorientation spreads reduced the intensity of the deformed texture and thus improved the texture predictions. Finally and moreover, considering that intragranular misorientations act as driving forces for recrystallization, the new GF-VPSC formulation is shown to enable modeling of microstructure evolution during deformation and recrystallization, in a computationally efficient manner.

36 MATERIALS SCIENCE↗

Extended continuous cooling transformation diagram for 410 stainless steel encompassing δ → γ and γ → αʹ transformations determined by dilatometry

In this study, we use dilatometry to construct an extended Continuous Cooling Transformation (CCT) diagram for 410 stainless steel, capturing both δ → γ and γ → αʹ transformations specifically for directed energy deposition (DED) additive manufacturing (AM) applications. To ensure that the findings are representative of AM specific microstructures and compositions, dilatometry coupons were extracted from a wire arc DED wall, thereby preserving the inherent microstructural and compositional variability within the material. The on-heating phase transformations, including A c1 , A c3 , and γ → δ, were found to be essentially location independent, despite the typical heterogeneity associated with AM. Conversely, increasing cooling rates were observed to shift the start and finish temperatures of both δ → γ and γ → αʹ transformations to lower values. The resulting extended CCT diagram offers a more complete depiction of phase transformation behavior in the system, enabling accurate microstructure evolution modeling and residual stress predictions specifically for directed energy deposition additive manufacturing applications.

Additive manufacturing↗

Pulse current auxiliary forging of sintered TiAl alloys based on the investigation of dynamic recrystallization and phase transformation

Highlights: • DRX kinetics model of sintered near γ TiAl alloy was established. • DRX process was accompanied by twinning when compressed at 1125 °C/0.1 s{sup − 1}. • Hot deformation has a promotion to the phase transformation of γ → α. - Abstract: Pulse current auxiliary forging is a new and efficient way to fabricate high performance TiAl based alloys. Dynamic recrystallization (DRX) and phase transformation have a pronounced effect on the subsequent deformability of TiAl based alloys. Hence, the dynamic recrystallization kinetics were determined at the temperature range of 1125–1275 °C and strain rate range of 0.1–0.001 s{sup − 1}. In addition, the DRX mechanism and phase transformation of TiAl based alloys were investigated to model the microstructure evolution in order to provide guidance for the pulse current auxiliary forging process. When the specimens were compressed at 1125 °C/0.1 s{sup − 1}, twinning played an important role in the DRX process. With increasing deformation temperature, the microstructure transformed from near gamma into duplex microstructure. In addition, according to the kinetics of dynamic recrystallization and phase transformation, fully DRXed TiAl based alloys were fabricated through pulse current auxiliary forging. The as-forged TiAl-based alloys show good superplastic performance with an elongation over 410%.

36 MATERIALS SCIENCE↗