Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “microporous”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

Through-plane conductivities of membranes for nonaqueous redox flow batteries

In this study, nonaqueous redox flow batteries (RFB) leverage nonaqueous solvents to enable higher operating voltages compared to their aqueous counterparts. Most commercial components for flow batteries, however, are designed for aqueous use. One critical component, the ion-selective membrane, provides ionic conductance between electrodes while preventing crossover of electroactive species. Here we evaluate the area-specific conductances and through-plane conductivities of commercially available microporous separators (Celgard 2400, 2500) and anion exchange membranes (Neosepta AFX, Neosepta AHA, Fumasep FAP-450, Fumasep FAP-PK) soaked in acetonitrile, propylene carbonate, or two imidazolium-based ionic liquids. Fumasep membranes combined with acetonitrile-based electrolyte solutions provided the highest conductance values and conductivities by far. When tested in ionic liquids, all anion exchange membranes displayed conductivities greater than those of the Celgard microporous separators, though the separators’ decreased thickness-enabled conductances on par with the most conductive anion exchange membranes. Ionic conductivity is not the only consideration when choosing an anion exchange membrane; testing of FAP-450 and FAP-PK membranes in a nonaqueous RFB demonstrated that the increased mechanical stability of PEEK-supported FAP-PK minimized swelling, in turn decreasing solvent mediated crossover and enabling greater electrochemical yields (40% vs. 4%) and Coulombic efficiencies (94% vs. 90%) compared to the unsupported, higher conductance FAP-450.

25 ENERGY STORAGE↗

In-situ investigation water distribution in polymer electrolyte fuel cell using neutron radiography

This paper investigates the water content within operating polymer electrolyte membrane (PEM) fuel cells using neutron radiography. We consider fuel cells with various PTFE loadings in their gas diffusion layers (GDL) and microporous layers (MPL), and examine the impacts of MPL/GDL properties on the liquid water behavior and fuel cell performance. Fuel cells are tested at both dry and fully hydrated conditions with different serpentine flow fields. Water contents in the projected areas of channel and land regions are probed. The fuel cell may be subject to more flooding at low current-density operation. Both MPL and GDL wetting properties have substantial impacts on the water content in fuel cell. Cell performance also varies on different scenarios of the MPL/GDL wetting properties. A quad-serpentine channel flow field exhibits higher water content without remarkable change in performance at low current densities. Liquid water profile along the channel is presented and on-set clearly indicated.

30 DIRECT ENERGY CONVERSION↗

Pore characterization of the Marcellus Shale by nitrogen adsorption and prediction of its gas storage capacity

In a shale gas reservoir, pore characterization is an important factor used to determine gas storage capacity. However, the nanometer (nm)-scale pore system in shale is difficult to explore by traditional optical, scanning electron microscopy, or even nuclear magnetic resonance well logging. We have investigated the pore structure and storage capacity of the Marcellus Shale through integration of petrophysical analysis from laboratory and well-logging data and nitrogen adsorption. The isotherm of Marcellus Shale is a composite isotherm, which has features of type I, type II, and type IV isotherms with type H4 of the hysteresis loop, suggesting slit-like pores developed in the Marcellus Shale. Quantitative analysis of pore volumes from the nitrogen adsorption indicates that density porosity may be more properly used to approximate the shale porosity and estimate the shale gas volume. In addition, the specific surface area, micropore, and mesopore volumes have a positive relationship with the kerogen volume and total organic content (TOC). By using the Langmuir and Brunauer-Emmet-Teller models, the simulated result indicates that the higher adsorbed quantity of the Marcellus Shale could be the result of the increase of micropore volume contributed, by the increase of kerogen or TOC content. The proposed equations rapidly compute TOC, a key parameter to predict gas storage capacity in overmature shale such as the Marcellus Shale.

Geochemistry & Geophysics↗

Curvature effects on carbon nanomaterials: Exohedral versus endhohedral supercapacitors

Capacitive energy storage mechanisms in nanoporous carbon supercapacitors hinge on endohedral interactions in carbon materials with macro-, meso-, and micropores that have negative surface curvature. In this article, we show that because of the positive curvature found in zero-dimensional carbon onions or one-dimensional carbon nanotube arrays, exohedral interactions cause the normalized capacitance to increase with decreasing particle size or tube diameter, in sharp contrast to the behavior of nanoporous carbon materials. This finding is in good agreement with the trend of recent experimental data. Our analysis suggests that electrical energy storage can be improved by exploiting the highly curved surfaces of carbon nanotube arrays with diameters on the order of 1 nm.

25 ENERGY STORAGE↗

Development of Biomimetic Membranes for Near Zero PC Power Plant Emissions

The first objective of this project was to develop, evaluate and compare two different CO2 separation (capture) systems. The second was to carry the preferred solution to pre-pilot development and testing. To achieve these objectives we undertook several infrastructure enabling elements: (1) development of a preferred catalyst coupled with its immobilization onto a microporous polymer membrane, (2) design and development of a microporous membrane-based, contained liquid membrane permeator and a membrane-based absorber/desorber apparatus, (3) development of a resin-wafer electrodialytic absorber/desorber apparatus, (4) development and demonstration of a pre-treatment process to condition the feed gas stream, (5) and development of computer modeling of the components and of the integrated system. The first technology was an enzyme catalyzed, membrane supported, contained liquid membrane apparatus whose gas capture was pressure/vacuum and temperature driven. A first embodiment was as a permeator, i.e. a combined absorber/desorber in a single housing. The second embodiment was as discrete absorber and desorber units. The second technology was an enzyme catalyzed, ion exchange resin wafer electrodialytically-based separation. For each of these technologies the objective was to design, manufacture, test and demonstrate the apparatus, first in the laboratory and then at pre-pilot scale, and to run it for sufficient time at the pre-pilot scale to demonstrate stability even in the face of upset. Tests would include several ranks of coal, which had been appropriately pre-treated to remove NOx, SOx and particles, to a pre-determined acceptance level, as a basis for demonstrating efficient CO{sub 2} capture. The pre-pilot tests would be run at the Energy and Environmental Research Center (EERC) in North Dakota. A larger scale test (400m{sup 2} test unit) would later be run also at EERC. An economic goal was to compare the cost of CO{sub 2} capture by each of these methods with values obtained when using MEA (monoethanolamine) as a baseline case. Other metrics included capital and operating expense, parasitic loss and cost of electricity. A final goal was to carry out an initial examination of market forces to understand what barriers to entry for installation of CO{sub 2} capture equipment might exist and their relative importance.

01 COAL, LIGNITE, AND PEAT↗

Rh-Based Mixed Alcohol Synthesis Catalysts: Characterization and Computational Report

The U.S. Department of Energy is conducting a program focused on developing a process for the conversion of biomass to bio-based fuels and co-products. Biomass-derived syngas is converted thermochemically within a temperature range of 240 to 330°C and at elevated pressure (e.g., 1200 psig) over a catalyst. Ethanol is the desired reaction product, although other side compounds are produced, including C 3 to C 5 alcohols; higher (i.e., greater than C 1 ) oxygenates such as methyl acetate, ethyl acetate, acetic acid and acetaldehyde; and higher hydrocarbon gases such as methane, ethane/ethene, propane/propene, etc. Saturated hydrocarbon gases (especially methane) are undesirable because they represent a diminished yield of carbon to the desired ethanol product and represent compounds that must be steam reformed at high energy cost to reproduce CO and H 2 . Ethanol produced by the thermochemical reaction of syngas could be separated and blended directly with gasoline to produce a liquid transportation fuel. Additionally, higher oxygenates and unsaturated hydrocarbon side products such as olefins also could be further processed to liquid fuels. The goal of the current project is the development of a Rh-based catalyst with high activity and selectivity to C 2 + oxygenates. This report chronicles an effort to characterize numerous supports and catalysts to identify particular traits that could be correlated with the most active and/or selective catalysts. Carbon and silica supports and catalysts were analyzed. Generally, analyses provided guidance in the selection of acceptable catalyst supports. For example, supports with high surface areas due to a high number of micropores were generally found to be poor at producing oxygenates, possibly because of mass transfer limitations of the products formed out of the micropores. To probe fundamental aspects of the complicated reaction network of CO with H 2 , a computational/ theoretical investigation using quantum mechanical and ab initio molecular dynamics calculations was initiated in 2009. Computational investigations were performed first to elucidate understanding of the nature of the catalytically active site. Thermodynamic calculations revealed that Mn likely exists as a metallic alloy with Rh in Rh-rich environments under reducing conditions at the temperatures of interest. After determining that reduced Rh-Mn alloy metal clusters were in a reduced state, the activation energy barriers of numerous transition state species on the catalytically active metal particles were calculated to compute the activation barriers of several reaction pathways that are possible on the catalyst surface. Comparison of calculations with a Rh nanoparticle versus a Rh-Mn nanoparticle revealed that the presence of Mn enabled the reaction pathway of CH with CO to form an adsorbed CHCO species, which was a precursor to C 2 + oxygenates. The presence of Mn did not have a significant effect on the rate of CH 4 production. Ir was observed during empirical catalyst screening experiments to improve the activity and selectivity of Rh-Mn catalysts. Thus, the addition of Ir to the Rh-Mn nanoparticles also was probed computationally. Simulations of Rh-Mn-Ir nanoparticles revealed that, with sufficient Ir concentrations, the Rh, Mn and Ir presumably would be well mixed within a nanoparticle. Activation barriers were calculated for Rh-Mn-Ir nanoparticles for several C-, H-, and O-containing transitional species on the nanoparticle surface. It was found that the presence of Ir opened yet another reactive pathway whereby HCO is formed and may undergo insertion with CHx surface moieties. The reaction pathway opened by the presence of Ir is in addition to the CO + CH pathway opened by the presence of Mn. Similar to Mn, the presence of Ir was not found to not affect the rate of CH 4 production.

catalyst↗

Low-Cost Proton Conducting Membranes for PEM Fuel Cells

Proton exchange membrane (PEM) is the key component in PEM fuel cells that critically determines the system performance and its economic viability. Presently, the state-of-the-art PEMs, such as Nafion membranes, are based on perfluorosulfonic acid (PFSA) ionomers. But these ionomer materials are expensive, particularly at the low volumes that will be needed for initial commercialization. Besides, they are not suitable for fuel cells operated beyond 100°C, because of the limitations connected to the humidification requirement of such membrane materials, limiting the maximum operating temperature to about 90°C. Fuel cells for transportation applications are required to operate in a wide temperature range from –20°C to 120°C. Low-cost PEMs with capabilities in a range of temperature and humidity conditions are urgently needed to meet the DOE fuel cell targets for transportation applications. Amsen Technologies LLC chooses to address the DOE call with a novel reinforced PEM approach based on new, non-PFSA proton conducting ionomers developed from our previous DOE SBIR projects. Along with this approach is the use of very cheap, ultra thin and highly porous microporous polymer meshes as the support for the membrane. The new PEM is expected to have significant cost advantages over traditional PEMs. The microporous polyolefin support costs $2-3/m 2 ; and the new ionomers that Amsen has developed are estimated at ~$\$$250/kg at the higher end including material costs and labor costs (which may go down in the future as the processing is optimized and production scaled up). These have led to an estimate of total material cost for the membrane at $\$$11 to $\$$12/m 2 , offering high potential of meeting the DOE cost targets (≤$\$$20/m 2 ) after adding processing cost and profit margin. The Phase I results have successfully demonstrated that it is very promising to develop the intended low-cost, high-performance PEM membrane. Suitable material system has been identified, and suitable process for forming the new PEM has been developed. Uniform membranes have been reproducibly fabricated. These membranes have been extensively characterized and evaluated in terms of microstructural features, and relevant physical and chemical properties including proton conductivity and area specific proton resistance in a range of temperature and humidity conditions, resistance to electronic conduction, water uptake/swelling, dimensional stability, chemical stability, and mechanical durability. Membrane electrode assemblies (MEA) with the new membrane have been successfully prepared and tested for fuel cell operation. The new PEM showed higher proton conductivity than Nafion membranes for all measurement conditions used in Phase I. With high proton conductivity and ultra-thin thickness (~20 /m), the new membrane showed high promise to met DOE targets for the low ASR. The ASR targets have been met for relatively high RH but not yet for RH ≤ 70%. Further optimization in ionomer chemistry and membrane processing is needed in order to meet the ASR targets for a wide range of temperature and humidity conditions. The new membrane showed fairly high electronic resistance at 1373 ohm cm 2 , meeting the DOE target for electronic resistance (> 1000 ohm cm 2 ). The new membrane also has demonstrated promisingly high chemical stability, high mechanical durability, and high dimensional stability. Fuel cell operation using MEAs with the new membrane have shown the same level of fuel cell performance as MEAs with Nafion membranes. Overall, the new membrane has been demonstrated to have high potential of meeting all DOE performance targets for fuel cell applications as well as the cost targets. The manufacturers of PEM fuel cells, PEM electrolyzers, redox flow batteries, and MEA are the end-users and customers of PEMs. For commercialization purpose and potential partnering relations, we have been talking with many such manufacturers. They have responded with extremely high interest in the new PEM being developed in the present technology. Accomplishments so far have laid down a strong base for Amsen to further the development efforts on this new PEM and to pursue commercialization. The near-term future work will be mainly focused on further development and systematical optimization of the material system, processing, and performance of the new membrane; systematical evaluation of the new membrane in terms of all relevant properties including long-term mechanical, chemical, and combined chemical/mechanical durabilities using DOE specified testing protocols; development of production scale-up scheme; and preparation for commercialization.

08 HYDROGEN↗

Developing a Novel Hydrogen Sponge with Ideal Binding Energy and High Surface Area for Practical Hydrogen Storage

This Phase I (5 quarters) research project was to examine the validity of a new class of boron-containing polymer (B-polymer) frameworks, serving as the adsorbents for the practical onboard H2 storage applications. Three B-polymer frameworks were synthesized and investigated, which include B-poly(butyenylstyrene) (B-PBS) framework (A), B-poly(phenyldiacetyene) (B-PPDA) framework (B), and B-poly(phenyltriacetylene) (B-PPTA) framework (C). They are 2-D polymer structures with the repeating cyclic units that spontaneously form open morphology and the B-doped (p-type) π-electrons delocalized surfaces. The ideal B-polymer framework shall exhibit open micropores (pore size in the range of 1-1.5nm) with high surface area (>3000 m 2 /g), and the B-dopants in the conjugated framework shall provide high surface energy for interacting with H 2 molecules (an ideal H 2 binding energy in the range of 15-25 kJ/mol). The pore size distribution and H2 binding energy were investigated at both Penn State and NREL laboratories. So far, the experimental results show the successful synthesis of B-polymer frameworks with the relatively well-defined planar (2-D) structures. The intrinsically formed porous morphology exhibits a broad pore size distribution (in the range of 0.5-10 nm) with specific surface area (~1000 m 2 /g). The miss-alignment between 2-D layers may block some micropore channels and limit gas diffusion throughout the entire matrix. In addition, the 2-D planar conjugated structure may also allow free π-electrons delocalization throughout the framework, which significantly reduces the acidity of B-moieties (electron-deficiency).The resulting 2-D B-polymer frameworks only exhibit a small increase of H 2 binding energy in the range of 8-9 KJ/mole (quite constant over the whole sorption range).

08 HYDROGEN↗

High Energy Storage Capacity Low Cost Iron Flow Battery

A new flow battery was proposed that utilizes low cost materials: iron as the only active element, cheap aqueous electrolytes, and inexpensive separators. During charging, ferrous iron (Fe 2+ ) is oxidized to ferric iron (Fe 3+ ) at the positive electrode while it (Fe 2+ ) is reduced to form iron metal (Fe 0 ) at the negative electrode. Because iron is plated at the negative electrode during charging, conventional electrode structures couple the energy storage capacity and the power rating of the battery. In order to decouple the energy and power ratings and regain the economic advantages of a flow battery, a slurry electrode design was proposed for use as the negative electrode. The slurry electrode is made by flowing electrically conductive particles in an electrolyte containing the dissolved iron species. On charging, iron is plated onto the particles. The particles can then carry the iron metal out of the cell to be stored in external reservoirs. This project looked to develop a slurry for the negative electrode of the all-iron flow battery that can operate at 200 mA/cm 2 with <100 mV overpotential, be pumped with parasitic energy costs < 10%, and promote plating on the particles. A scalable and stackable cell design of 1100 cm 2 was developed. The project was initially under contract in mid-January 2013. The project was converted from a one-year proof of concept seedling to an additional two-year program, then extended with an 18-month plus-up, and finally with an additional 6-month approved cost-overrun. During the seeding project, the concept of plating on carbon particles in a slurry was demonstrated. However, this was accomplished with high-cost multi-walled carbon nanotubes as the slurry material. The following two-year program discovered several low-cost carbon blacks that could also be used in this application. These findings were supported by an analysis that demonstrated the effectiveness of the carbon that takes into account not just the effective electronic conductivity of the slurry, but also the surface area per volume of the slurry. It was demonstrated that stable, flowable slurries could be created with these carbons, even when the carbons where fully loaded with iron during charging. During the two-year program, laboratory-scale 50 cm 2 single-cells demonstrated charge-discharge cycling at current densities of 150 mA/cm 2 and energy efficiencies of >50%. Meanwhile, cost modeling continued to show promise for this energy storage approach. Following the conversion period, the overall objective of the nominally 18-month plus up period was to close the technical gap of a 25X scale-up and reduce risk to enable commercial investment required to develop a slurry iron flow battery product. A specific objective was to demonstrate 150 cycles of performance exceeding 70% energy efficiency with a 10-cell stack of 1156 cm 2 cells operating at 100 mA/cm 2 . The 10-cell short stack was designed to have a power delivery rating of approximately 1 kW, which represents a size commensurate with the requirements of our commercialization partner at that time. A complete battery support system for the full-size cell was designed, fabricated, and tested. This includes pumps (multiple types were considered, and constant volume hose pumps were found to be acceptable for performance and cost), electrolyte rebalance reactor, and sensors and control systems. The support system proved to be well-behaved and worked well. A new low-cost membrane was developed for this system based on a microporous polymer support with a layer of hydrogel polymer. The membrane had low resistivity, and significantly reduced pressure driven fluid flow across the membrane (as compared to the un-coated microporous support). This membrane approach was scaled-up in conjunction with a commercial toll coating company, and a large amount of membrane was manufactured to support large cell and stack testing. A new concept for an electrolyte rebalance reactor to react hydrogen gas from the negative electrolyte (from plating inefficiency) with excess ferric ion in the positive electrolyte was developed. This design was very simple, low cost, and effective. The full scale 1156 cm 2 single-cell was designed, modeled, fabricated and tested. Modeling showed that uniform flow-distribution should be obtained with the designed flow distributor. The design took into consideration the need to stack the cells, and components were fabricated for a ten-cell stack. Testing of the cell for charge and discharge demonstrated current densities of 50 mA/cm 2 with efficiencies of 50%. However, optimization and long cycling could not be accomplished because the slurry electrode would plug within the cell and block the flow. This would shut down the cell after several charge-discharge cycles. Various approaches were pursued to address this problem with some progress. However, there was not adequate time to find solutions to the problem although several promising approaches were identified for future work. The final deliverable for this proposed 18-month effort was to be a 1 kW, 6 kWh slurry flow battery, with complete balance of plant, ready for testing at an ARPA-E ‘Charges’ site with an estimated capital cost less than $\$ $45/kWh for a six-hour system (excluding power electronics). The deliverable milestone was not achieved for reasons mentioned above related to the slurry plugging. At the completion of this project, it was determined that the cost targets are achievable. The cost estimate for a 1 MW system with a one-hour capacity was estimated at $\$ $140/kWh (including power electronics) and for a six-hour system was estimated at $\$ $40/kWh (including power electronics). These costs include the battery, the balance of plant, the power conditioning and a concrete pad. This program resulted in three patents including the slurry-based iron flow battery, the rebalance reactor, and the membrane separator. At the time of this report, slurry-based iron flow battery patents have been issued in the US, China, Japan, Korea, and Europe. The other patent applications were under various stages of examination. A licensee was identified and the company initiated a scale-up and development program to take this technology to the marketplace, and CWRU staff have transferred their know-how and knowledge base to the company. This technology will enhance the economic and energy security of the United States by enabling the use of intermittent renewable energy technology, such as wind and solar power, as dispatchable resources. This report summarizes the results of this research and development program.

25 ENERGY STORAGE↗

Electrodeposition of Nanostructured Copper on Gas Diffusion Layers as Electrocatalysts for Carbon Dioxide Reduction

The aim of the summer project was to immobilize copper nanostructures on gas diffusion layers to serve as electrocatalysts for the electrochemical reduction of CO 2 . Gas diffusion layers are typically bilayer structures consisting of a macro-porous backing material (carbon fiber paper) and a microporous, carbon-based layer (MPL). Classically, the copper catalysts are loaded on the microporous layer. Furthermore, the GDL is intrinsically hydrophobic due to polytetrafluoroethylene (PTFE)in its chemical composition, with the MPL having a more hydrophobic character due to its higher PTFE content. While beneficial for rendering the MPL impervious to electrolytes during actual CO 2 reduction, the hydrophobicity precludes sufficient wetting of the MPL layer, preventing conformal, uniformly distributed and strongly adhered deposits. A two electrode electrodeposition system was used to facilitate copper deposition. An implication of this system is the inability to ascertain or accurately modulate the cathodic over-potential. Hence, galvanostatic (current control) procedures are utilized for all deposition. To improve the wetting behavior of the MPL, the surface is subjected to surface pretreatment protocols prior to electrodeposition. In addition, as morphology of deposits play a role in their efficacy as catalysts in terms of selectivity and conversion, we systematically investigate the effects of different galvanostatic deposition procedures on copper morphology.

36 MATERIALS SCIENCE↗

Effects of Pore Size on Na/Ca Ion Selectivity Using Flow Through Electrode Capacitive Deionization

In flow through electrode capacitive deionization (fte-CDI), low salinity brackish water flows through two porous carbon electrodes. When an electrical potential difference is applied over the electrodes, ions migrate towards micropores, cleaning the water. Ion selectivity can be controlled by taking advantage of charge and ionic radius differences as well as the applied potential and pore size of the electrodes. The research outlined in this paper consists primarily of running fte-CDI cells with electrodes of varying pore size distributions to experimentally determine the parameters for optimal total salt removal and sodium/calcium ion selectivity. Five fte-CDI cells of different activation were fabricated using microporous hierarchical carbon aerogel materials (HCAMs) as electrodes. For each cell, cyclic voltammetry using 20 mM NaCl solution and 10 mM CaCl2 solution was performed at a scan rate of 0.5, 0.75, and 1 mV/s with a potential window from -0.8 V to +0.8 V. The same pure salts were desalinated in hourly charge/discharge cycles at ±1 V. A mixture of 5 mM NaCl and 2.5 mM CaCl2 was desalinated at 0.6, 0.8, 1.0, and 1.2 V. The collected charge and discharge streams were analyzed with ion chromatography (IC). The IC data for the two least activated cells showed minimal calcium adsorption compared to sodium. All cells adsorbed sodium, regardless of activation, while only highly activated cells removed calcium. This data indicates a tradeoff between more total salt removed at high voltages and selectivity of sodium over calcium at low voltages. Future research with nitrogen porosimetry could provide a quantitative value for the optimal pore size distribution.

36 MATERIALS SCIENCE↗

Porous Organic Cage Membranes for Molecular Gas Separations (Final Technical Report for DE-SC0021357)

This proposal aims at demonstrating the development of a novel family of membranes, composed of porous organic cages (POC) which offer the possibility of displaying high separation performance for challenging molecular gas separations relevant to natural gas purification, and olefin/paraffin separation. The proposed POCs synthesized in membrane form will display the most desirable properties of polymers (facile processability and flexibility) and inorganic materials (hierarchically ordered pores with molecular sieving properties) leading to highly selective and permeable membranes. POCs should display distinctive structural, compositional, adsorption and transport properties than those of conventional porous materials, opening the doors for a new research direction in membrane science, and gas separations. Our preliminary results demonstrate the feasibility of preparing POC crystals with controlled size, and continuous POC membranes with remarkable high permeances, and separation ability for CO 2 /CH 4 , N 2 /CH 4 and C 3 H 6 /C 3 H 8 separations serving as a solid foundation for our proposed work. Fundamentally, this proposal aims at elucidating separation mechanisms of different gas mixtures related to natural gas composition, and olefin/paraffin separation over porous organic cage membranes. The proposed research will result in fundamental understanding of adsorption and transport properties of industrially relevant gas molecules through novel microporous membranes, and may lead to the development of a cost effective membrane technology for natural gas purification, and olefin/paraffin separation surpassing the conventional benchmark technology distillation. Furthermore, we aim at demonstrating selective water transport through POC membranes, which can be positively impactful in numerous industrial applications in which water is present. The ability to fabricate thin, chemically and mechanically stable POC membranes for societal relevant gas separations constitute a new and distinctive direction in membrane science. Our proposed work aims at addressing some of the challenges recognized in the Research Agenda for Transforming Separation Science . Specifically: (a) advancing understanding of complex mixtures on separation performance; (b) exploring thermodynamic and kinetic mechanisms through the elucidation of separation mechanisms, and (c) study potential stability issues of the membranes to be assessed by evaluating the long term membrane stability and performance at various temperatures and pressures. The team is uniquely qualified to execute the proposed work. The PI has solid expertise in the rational molecular engineering design of porous crystalline membranes for molecular gas separations. The PNNL collaborator has extensive experience in the synthesis, characterization, and functional applications of microporous crystals, with particular emphasis on gas adsorption.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Measuring Multicomponent Adsorption of Tracer Gases on Natural Zeolites

A natural clinoptilolite sample near the Nevada National Security Site was obtained to study adsorption and retardation on gas transport. Of interest is understanding the competition for adsorption sites that may reduce tracer gas adsorption relative to single-component measurements, which may be affected by the multi-scale pore structure of clinoptilolite. Clinoptilolite has three distinct domains of pore size distributions ranging from nanometers to micrometers: micropores with 0.4–0.7 nm diameters, measured on powders by CO2 adsorption at 273 K, representing the zeolite cages; mesopores with 4–200 nm diameters, observed using liquid nitrogen adsorption at 77 K; and macropores with 300–1000 nm diameters, measured by mercury injection on rock chips (~ 100 mesh), likely representing the microfractures. These pore size distributions are consistent with X-ray computed tomography (CT) and focused ion beam scanning electron microscope (FIB-SEM) images, which are used to construct the three-dimensional (3D) pore network to be used in future gas transport modeling. To quantify tracer gas adsorption in this multi-scale pore structure and multicomponent gas species environment, natural zeolite samples initially in equilibrium in air were exposed to a mixture of tracer gases. As the tracer gases diffuse and adsorb in the sample, the remaining tracer gases outside the sample fractionate. Using a quadrupole mass spectrometer to quantify this fractionation, the degree of adsorption of tracer gases in the multicomponent gas environment and multi-scale pore structure is assessed. The major finding is that Kr reaches equilibrium much faster than Xe in the presence of ambient air, which leads to more Kr uptake than Xe over limited exposure periods. When the clinoptilolite chips were exposed to humid air, the adsorption capability decreases significantly for both Xe and Kr with relative humidity (RH) as low as 3%. Both Xe and Kr reaches equilibrium faster at higher RH. The different, unexpected, adsorption behavior for Xe and Kr is due to their kinetic diameters similar to the micropores in clinoptilolite which makes it harder for Xe to access compared to Kr.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

CalTestBed - Twelve Benefit Co - Understanding Degradation of Water Management Properties in Gas Diffusion Layers (CRADA Final Report)

The research between Lawrence Berkeley National Lab and Twelve Benefit Co. enhanced Twelve’s understanding of how chemical changes to the gas diffusion layer lead to failure of their CO 2 electrolyzers. During the CRADA period, LBNL team tested Twelve’s gas diffusion layer samples (GDL), some with microporous layer (MPL) and some without MPL using the water-air capillary pressure setup. LBNL team also tested microporous layer samples using the fuel cell test stands and compared those results with commercial GDL and MPL. Understanding the hydrophobicity of the material, along with electrochemical performance is the key to determining Twelve’s ability to scale their platform. Further improvements to Twelve’s CO 2 electrolyzer can enhance the net zero emissions with their technology.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Final Report

The premise of this project was that coordination chemistry could be used to devise new kinds of microporous materials and that these materials could exhibit nanoscale porosity and selective chemical separation capabilities. Our initial materials focus was on aggregates of discrete hollow molecules, especially molecular squares. Subsequently our focus turned largely toward permanently microporous metal-organic frameworks (MOFs). Our approach emphasized coupling predictive & explanative computational modeling to materials design, synthesis, and property characterization.

36 MATERIALS SCIENCE↗

Development of Pd-Ag Compostie Membrane for Separation of Hydrogen at Elevated Temperature

Pd-based membrane reactor offers the possibility of combining reaction and separation in a single operation at high temperatures to overcome the equilibrium limitations experienced in conventional reactor configurations. In this project to develop a defect-free and hermally-stable Pd-film on microporous stainless steel (MPSS) support for H2-separation and membrane reactor applications, the electroless plating process was revisited with an aim to improve the membrane morphology. Specifically, this study includes; (a) an improvement f activation step using Pulse Laser Deposition (PLD), (b) development of a novel surfactant induced electroless plating (SIEP) for depositing robust Pd-film on microporous support, and (c) application of Pd-membrane as membrane reactor in steam methanol reforming (SMR) reactions.

08 HYDROGEN↗

Properties of adsorbents prepared by the alkali activation of Aleksandriisk brown coal

Highly microporous adsorbents (micropore fraction of about 70%) were prepared by the alkali activation-thermolysis (800{sup o}C, 1 h) of brown coal (C{sup daf} = 70.4%) in the presence of potassium hydroxide at the KOH/coal weight ratio R{sub KOH} {le} 2.0 g/g. The dependences of the specific surface areas and adsorption capacities of the adsorbents for methylene blue (A{sub MB}, mg/g), iodine (A{sub I}, mg/g), and hydrogen (A{sub H{sub 2}} wt %) on R{sub KOH} were determined. The adsorbents obtained at R{sub KOH}{ge} 1.0 g/g exhibited developed specific surface areas and good adsorption characteristics (A{sub I} = 1000-1200 mg/g, A{sub MB} = 200-250 mg/g, and A{sub H{sub 2}} {le} 3.16 wt % at 0.33 MPa). The high capacity for hydrogen allowed us to consider brown coal adsorbents as promising materials for use as hydrogen accumulators.

01 COAL, LIGNITE, AND PEAT↗

Study on the Impacts of Capillary Number and Initial Water Saturation on the Residual Gas Distribution by NMR

The determination of microscopic residual gas distribution is beneficial for exploiting reservoirs to their maximum potential. In this work, both forced and spontaneous imbibition (waterflooding) experiments were performed on a high-pressure displacement experimental setup, which was integrated with nuclear magnetic resonance (NMR) to reveal the impacts of capillary number ( Ca ) and initial water saturation ( S wi ) on the residual gas distribution over four magnitudes of injection rates (Q = 0.001, 0.01, 0.1 and 1 mL/min), expressed as Ca (log Ca = –8.68, –7.68, –6.68 and –5.68), and three different S wi ( S wi = 0%, 39.34% and 62.98%). The NMR amplitude is dependent on pore volumes while the NMR transverse relaxation time ( T 2 ) spectrum reflects the characteristics of pore size distribution, which is determined based on a mercury injection (MI) experiment. Using this method, the residual gas distribution was quantified by comparing the T 2 spectrum of the sample measured after imbibition with the sample fully saturated by brine before imbibition. The results showed that capillary trapping efficiency increased with increasing S wi , and above 90% of residual gas existed in pores larger than 1 μm in the spontaneous imbibition experiments. The residual gas was trapped in pores by different capillary trapping mechanisms under different Ca , leading to the difference of residual gas distribution. The flow channels were mainly composed of micropores (pore radius, r < 1 μm) and mesopores ( r = 1–10 μm) at log Ca = –8.68 and –7.68, while of mesopores and macropores (r > 10 μm) at logCa = –5.68. At both S wi = 0% and 39.34%, residual gas distribution in macropores significantly decreased while that in micropores slightly increased with log Ca increasing to –6.68 and –5.68, respectively.

02 PETROLEUM↗