Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “materials characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Characterizing mode I fatigue delamination of composite materials

Two techniques for characterizing fatigue delamination in double cantilever beams, the delamination growth onset method and the delamination growth and arrest method, are evaluated. Two glass/epoxy systems, S2/SP250 and S2/CE9000, were tested at R = 0.1 and R = 0.5. The values of the strain energy release rate threshold Delta G(Ith) for no onset of delamination growth until one million cycles were compared with the values of Delta G(I) at delamination arrest. The values at arrest were consistently higher because fiber bridging occurred in the tests. Normalizing Delta G(I) by the mode I value of interlaminar fracture toughness G(Ir) at the corresponding delta A gave values of Delta G(I)/G(Ir) at delamination arrest which were closer to the threshold values obtained from the Delta G-N technique. However, this normalization did not represent a generic materials characterization technique and did not allow for delamination onset predictions.

Martin, Roderick H.↗
NASA NTRS1991

Discovery and characterization of lunar materials: An incomplete process

Our knowledge of lunar materials is based on (1) sample collections (by the Apollo and Lunar missions, supplemented by Antarctic lunar meteorites); and (2) remote sensing (Earth-based or by spacecraft). The characterization of lunar materials is limited by the small number of sampled sites and the incomplete remote-sensing database (geochemical data collected from orbit cover 20 percent of the lunar surface). There is much about lunar surface materials that remains to be discovered. Listed are some features suspected form present knowledge: (1) Polar Materials; (2) Farside Materials; (3) Crater-Floor Materials; (4) Crater-Wall and Central Peak Materials; (5) Volcanic Shield and Dome Materials; (6) Transient-Event Materials; and (7) Meteoritic and Cometary Materials; This short list of likely discoveries isn't exhaustive. We know much about a few spots on the Moon, but little about the full range of lunar materials.

Vaniman, D.↗
NASA NTRS1982

Photothermal characterization of encapsulant materials for photovoltaic modules

A photothermal test matrix and a low cost testing apparatus for encapsulant materials of photovoltaic modules were defined. Photothermal studies were conducted to screen and rank existing as well as future encapsulant candidate materials and/or material formulations in terms of their long term physiochemical stability under accelerated photothermal aging conditions. Photothermal characterization of six candidate pottant materials and six candidate outer cover materials were carried out. Principal products of photothermal degradation are identified. Certain critical properties are also monitored as a function of photothermal aging.

Liang, R. H.↗
NASA NTRS2003

Observational and Data Reduction Techniques to Optimize Mineralogical Characterizations of Asteroid Surface Materials

Mineralogy is the key to determining the compositional history of the asteroids and to determining the genetic relationships between the asteroids and meteorites. The most sophisticated remote mineralogical characterizations involve the quantitative extraction of specific diagnostic parameters from reflectance spectra and the use of quantitative interpretive calibrations to determine the presence, abundance and/or composition of mineral phases in a surface material. Although this approach is potentially subject to systematic errors, it provides the only consistent set of asteroid surface material characterizations.

Gaffey, M. J.↗
NASA NTRS2011

Characterization of Catalyst Materials for Production of Aerospace Fuels

Due to environmental, economic, and security issues, there is a greater need for cleaner alternative fuels. There will undoubtedly be a shift from crude oil to non-petroleum sources as a feedstock for aviation (and other transportation) fuels. Additionally, efforts are concentrated on reducing costs coupled with fuel production from non-conventional sources. One solution to this issue is Fischer-Tropsch gas-to-liquid technology. Fischer-Tropsch processing of synthesis gas (CO/H2) produces a complex product stream of paraffins, olefins, and oxygenated compounds such as alcohols and aldehydes. The Fisher-Tropsch process can produce a cleaner diesel oil fraction with a high cetane number (typically above 70) without any sulfur or aromatic compounds. This process is most commonly catalyzed by heterogeneous (in this case, silver and platinum) catalysts composed of cobalt supported on alumina or unsupported alloyed iron powders. Physisorption, chemisorptions, scanning electron microscopy (SEM), and energy dispersive spectroscopy (EDS) are described to better understand the potential performance of Fischer-Tropsch cobalt on alumina catalysts promoted with silver and platinum. The overall goal is to preferentially produce C8 to C18 paraffin compounds for use as aerospace fuels. Progress towards this goal will eventually be updated and achieved by a more thorough understanding of the characterization of catalyst materials. This work was supported by NASA s Subsonic Fixed Wing and In-situ Resource Utilization projects.

DeLaRee, Ana B.↗
NASA NTRS2012

Characterization of Catalyst Materials for Production of Aerospace Fuels

Due to environmental, economic, and security issues, there is a greater need for cleaner alternative fuels. There will undoubtedly be a shift from crude oil to non-petroleum sources as a feedstock for aviation (and other transportation) fuels. Additionally, efforts are concentrated on reducing costs coupled with fuel production from non-conventional sources. One solution to this issue is Fischer-Tropsch gas-to-liquid technology. Fischer-Tropsch processing of synthesis gas (CO/H2) produces a complex product stream of paraffins, olefins, and oxygenated compounds such as alcohols and aldehydes. The Fisher-Tropsch process can produce a cleaner diesel oil fraction with a high cetane number (typically above 70) without any sulfur or aromatic compounds. This process is most commonly catalyzed by heterogeneous (in this case, silver and platinum) catalysts composed of cobalt supported on alumina or unsupported alloyed iron powders. Physisorption, chemisorptions, scanning electron microscopy (SEM), and energy dispersive spectroscopy (EDS) are described to better understand the potential performance of Fischer-Tropsch cobalt on alumina catalysts promoted with silver and platinum. The overall goal is to preferentially produce C8 to C18 paraffin compounds for use as aerospace fuels. Progress towards this goal will eventually be updated and achieved by a more thorough understanding of the characterization of catalyst materials. This work was supported by NASA s Subsonic Fixed Wing and In-situ Resource Utilization projects.

Best, Lauren M.↗
NASA NTRSDate not supplied

Characterization of Novel Spacecraft Materials aboard the Materials International Space Station Experiment-Flight Facility (Preliminary Results)

This work will encompass the preflight characterization of 15 novel and heritage materials currently under observation on the Materials International Space Station Experiment-Flight Facility (MISSE-FF). MISSE-FF has been upgraded to perform active reflectance measurements of the materials. Images taken in RGB/IR colors are compared to results from an extensive ground testing campaign to obtain quantitative on-orbit material evolution data. Identical materials samples are to be flown on the ram, wake, and zenith faces of MISSE-FF, enabling deconvolution of the energetic electron, proton, atomic oxygen, and ultraviolet damage pathways. Energy deposition from the space environment leads to chemical changes in the material that in turn alter the optical properties. The same chemical damage that manifests as changes in optical reflectance and absorptance also leads to changes in myriad physical properties such as mechanical strength, electrical conductivity, and chemical reactivity. Therefore, flight materials are able to be characterized based on their unique reflectance spectra by comparing on-orbit measurements of optical reflectance with extensive terrestrial experiments, which help to correlate changes in reflectance with respect to changes in other material properties. The MISSE program has been a part of the International Space Station National Laboratory for many years and has been instrumental in understanding space weather modification of material properties. However, MISSE-FF has been limited to passive experiments with only pre/post flight material studies possible. In advance of the MISSE-16 experiment, the flight facility has received a major upgrade to provide daily spectral observations by way of a RGB/IR camera and a tunable light source. The MISSE-16 mission launched in February 2022 and carries 15 material samples for 6 months of the low Earth orbital exposure. Identical materials samples are to be flown on the ram, wake, and zenith faces of MISSE-FF, enabling deconvolution of the energetic electron, proton, atomic oxygen, and ultraviolet damage pathways. This paper discusses the MISSE-16 experiment, highlights the first use of the facility upgrades, and presents results from the extensive preflight material characterization that includes directional hemispherical reflectance, bidirectional reflectance, AFM, SEM, and electrical conductivity. Additionally, data showing the modification of these properties by ground-based exposure to space-like electron and atomic oxygen flux will be discussed. Finally, updates on deployment and initial check-out of the experiment on MISSE-FF will be presented. It is the ultimate goal of this program to provide validation for the development of ground based space weather simulation facilities and techniques.

Ryan Hoffman↗
NASA NTRS2016

Characterization of Candidate Materials for Remote Recession Measurements of Ablative Heat Shield Materials

A method of remotely measuring surface recession of a material sample in a plasma flow through emission spectroscopy of the post shock layer was characterized through experiments in the NASA Langley HYMETS arc jet facility. Different methods for delivering the seed products into the Phenolic Impregnated Carbon Ablator (PICA) material samples were investigated. Three samples were produced by seeding the PICA material with combinations of Al, Si, HfO2, VB2, Al2O3, SiO2, TiC, HfC, NaCl, and MgCl2 through infusing seed materials into a core of PICA, or through encapsulating seed material in an epoxy disk, mechanically bonding the disk to a PICA sample. The PICA samples seeded with the candidate tracers were then tested at surface temperatures near 2400 K under low pressure air plasma. The emission of Al, Ti, V, Na, and Mg in the post-shock layer was observed in the UV with a high resolution imaging spectrometer viewing the whole stagnation line from the side, and from UV to NIR with a fiber-coupled miniaturized spectrometer observing the sample surface in the wavelength range from 200 nm to 1,100 nm from the front through a collimator. Al, Na, and Mg were found to be emitting in the post-shock spectra even before the recession reached the seeding depth - therefore possibly characterizing the pyrolysis process rather than the recession itself. The appearance of Ti and V emission in the spectra was well correlated with the actual recession which was monitored through a video of the front surface of the sample. The applicability of a seed material as an indicator for recession appears to be related to the melting temperature of the seed material. Future parametric studies will be carried out in low power plasma facilities at the University of Kentucky.

Butler, Bradley D.↗
NASA NTRS2000

Characterization of Electronic Materials HgZnSe and HgZnTe Using Innovative and Conventional Techniques

HgZnSe and HgZnTe are electronic materials of interest for potential IR detector and focal plane array applications due to their improved strength and compositional stability over HgCdTe, but they are difficult to grow on Earth and to fully characterize. Conventional contact methods of characterization, such as Hall and van der Paw, although adequate for many situations are typically labor intensive and not entirely suitable where only very small samples are available. To adequately characterize and compare properties of electronic materials grown in low earth orbit with those grown on Earth, innovative techniques are needed that complement existing methods. This paper describes the implementation and test results of a unique non-contact method of characterizing uniformity, mobility, and carrier concentration together with results from conventional methods applied to HgZnSe and HgZnTe. The innovative method has advantages over conventional contact methods since it circumvents problems of possible contamination from alloying electrical contacts to a sample and also has the capability to map a sample. Non- destructive mapping, the determination of the carrier concentration and mobility at each place on a sample, provides a means to quantitatively compare, at high spatial resolution, effects of microgravity on electronic properties and uniformity of electronic materials grown in low-Earth orbit with Earth grown materials. The mapping technique described here uses a 1mm diameter polarized beam of radiation to probe the sample. Activation of a magnetic field, in which the sample is placed, causes the plane of polarization of the probe beam to rotate. This Faraday rotation is a function of the free carrier concentration and the band parameters of the material. Maps of carrier concentration, mobility, and transmission generated from measurements of the Faraday rotation angles over the temperature range from 300K to 77K will be presented. New information on band parameters, obtained by combining results from conventional Hall measurements of the free carrier concentration with Faraday rotation measurements, will also be presented. One example of how this type of information was derived is illustrated in the following figure which shows Faraday rotation vs wavelength modeled for Hg(l-x)ZnxSe at a temperature of 300K and x=0.07. The plasma contribution, total Faraday rotation, and interband contribution to the Faraday rotation, are designated in the Figure as del(p), FR tot, and del(i) respectively. Experimentally measured values of FR tot, each indicated by + , agree acceptably well with the model at the probe wavelength of 10.6 microns. The model shows that at the probe wavelength, practically all the rotation is due to the plasma component, which can be expressed as delta(sub p)= 2pi(e(sup 3))NBL/c(sup 2)nm*(sup 2) omega(sup 2). In this equation, delta(sub p) is the rotation angle due to the free carrier plasma, N is the free carrier concentration, B the magnetic field strength, L the thickness of the sample, n the index of refraction, omega the probe radiation frequency, c the speed of light, e the electron charge, and m* the effective mass. A measurement of N by conventional techniques, combined with a measurement of the Faraday rotation angle allows m* to be accurately determined since it is an inverse square function.

Tanton, George↗
NASA NTRS1994

Composite Material Property Nondestructive Characterization Using Obliquely Insonified Ultrasonic Waves

The analysis of reflected ultrasonic waves induced by oblique insonification of composite materials is a powerful tool for providing informations about defects and material properties. A device was developed to manipulate a pair of transmitting and receiving transducers at vrious angles of wave incidence and propagation with the fiber orientation.

Non-Destructive Evaluation Composites Mechanical P↗
NASA NTRS1992

A comparison of conventional and advanced ultrasonic inspection techniques in the characterization of TMC materials

Results obtained with a conventional ultrasonic inspection technique as well as those obtained with more advanced ultrasonic NDE methods in the characterization of an 8-ply quasi-isotropic titanium matrix composite (TMC) specimen are presented. Images obtained from a conventional ultrasonic inspection of TMC material are compared with those obtained using more sophisticated ultrasonic inspection methods. It is suggested that the latter techniques are able to provide quantitative images of TMC material. They are able to reveal the same potential defect indications while simultaneously providing more quantitative information concerning the material's inherent properties. Band-limited signal loss and slope-of-attenuation images provide quantitative data on the inherent material characteristics and defects in TMC.

Holland, Mark R.↗
NASA NTRS1995

Nonlinear viscoelastic characterization of polymer materials using a dynamic-mechanical methodology

Polymer materials retrieved from LDEF exhibit nonlinear constitutive behavior; thus the authors present a method to characterize nonlinear viscoelastic behavior using measurements from dynamic (oscillatory) mechanical tests. Frequency-derived measurements are transformed into time-domain properties providing the capability to predict long term material performance without a lengthy experimentation program. Results are presented for thin-film high-performance polymer materials used in the fabrication of high-altitude scientific balloons. Predictions based upon a linear test and analysis approach are shown to deteriorate for moderate to high stress levels expected for extended applications. Tests verify that nonlinear viscoelastic response is induced by large stresses. Hence, an approach is developed in which the stress-dependent behavior is examined in a manner analogous to modeling temperature-dependent behavior with time-temperature correspondence and superposition principles. The development leads to time-stress correspondence and superposition of measurements obtained through dynamic mechanical tests. Predictions of material behavior using measurements based upon linear and nonlinear approaches are compared with experimental results obtained from traditional creep tests. Excellent agreement is shown for the nonlinear model.

Strganac, Thomas W.↗
NASA NTRS1983

A study of the stress wave factor technique for the characterization of composite materials

A testing program was undertaken to provide an independent investigation and evaluation of the stress wave factor for characterizing the mechanical behavior of composite laminates. Some of the data which was obtained after performing a very large number of tests to determine the reproducibility of the SWF measurement is presented. It was determined that, with some optimizing of experimental parameters, the SWF value can be reproduced to within + or - 10%. Results are also given which show that, after careful calibration procedures, the lowest SWF value along the length of a specimen will correlate very closely to the site of final failure when the specimen is loaded in tension. Finally, using a moire interferometry technique, it was found that local regions having the highest in plane strains under tensile loading also had the lowest SWF values.

Henneke, E. G., II↗
NASA NTRS1986

Analytical Ultrasonics in Materials Research and Testing

Research results in analytical ultrasonics for characterizing structural materials from metals and ceramics to composites are presented. General topics covered by the conference included: status and advances in analytical ultrasonics for characterizing material microstructures and mechanical properties; status and prospects for ultrasonic measurements of microdamage, degradation, and underlying morphological factors; status and problems in precision measurements of frequency-dependent velocity and attenuation for materials analysis; procedures and requirements for automated, digital signal acquisition, processing, analysis, and interpretation; incentives for analytical ultrasonics in materials research and materials processing, testing, and inspection; and examples of progress in ultrasonics for interrelating microstructure, mechanical properites, and dynamic response.

Vary, A.↗
NASA NTRS1978

A new experimental method for the accelerated characterization of composite materials

The use of composite materials for a variety of practical structural applications is presented and the need for an accelerated characterization procedure is assessed. A new experimental and analytical method is presented which allows the prediction of long term properties from short term tests. Some preliminary experimental results are presented.

Yeow, Y. T.↗
NASA NTRS2016

Crystallographic Characterization of Extraterrestrial Materials by Energy-Scanning X-ray Diffraction

We have continued our long-term project using X-ray diffraction to characterize a wide range of extraterrestrial samples. The stationary sample method with polychromatic X-rays is advantageous because the irradiated area of the sample is always same and fixed, meaning that all diffraction spots occur from the same area of the sample, however, unit cell parameters cannot be directly obtained by this method though they are very important for identification of mineral and for determination of crystal structures. In order to obtain the cell parameters even in the case of the sample stationary method, we apply energy scanning of a micro-beam of monochromatic SR at SPring-8.

Hagiya, Kenji↗
NASA NTRS2003

Characterization of Candidate Solar Sail Material Exposed to Space Environmental Effects

Solar sailing is a unique form of propulsion where a spacecraft gains momentum from incident photons. Solar sails are not limited by reaction mass and provide continual acceleration, reduced only by the lifetime of the lightweight film in the space environment and the distance to the Sun. Once thought to be difficult or impossible, solar sailing has come out of science fiction and into the realm of possibility. Any spacecraft using this method would need to deploy a thin sail that could be as large as many kilometers in extent. The availability of strong, ultra lightweight, and radiation resistant materials will determine the future of solar sailing. The National Aeronautics and Space Administration's Marshall Space Flight Center (MSFC) is concentrating research into the utilization of ultra lightweight materials for spacecraft propulsion. The Space Environmental Effects Team at MSFC is actively characterizing candidate solar sail material to evaluate the thermo-optical and mechanical properties after exposure to space environmental effects. This paper will describe the exposure of candidate solar sail materials to emulated space environmental effects including energetic electrons, combined electrons and Ultraviolet radiation, and hypervelocity impact of irradiated solar sail material. This paper will describe the testing procedure and the material characterization results of this investigation.

Edwards, David↗
NASA NTRS1984

Characterization of Glass Fiber Separator Material for Lithium Batteries

Characterization studies were carried out on a glass fiber paper that is currently employed as a separator material for some LiSOCl2 primary cells. The material is of the non-woven type made from microfilaments of E-type glass and contains an ethyl acrylate binder. Results from extraction studies and tensile testing revealed that the binder content and tensile strength of the paper were significantly less than values specified by the manufacturer. Scanning electron micrographs revealed the presence of clusters of impurities many of which were high in iron content. Results of emission spectroscopy revealed high overall levels of iron and leaching, followed by atomic absorption measurements, revealed that essentially all of this iron is soluble in SOCl2.

Subbarao, S.↗