Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “hydrogen compression”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Grid-Integrated Production of Fischer-Tropsch Synfuels from Nuclear Power

Idaho National Laboratory (INL) investigates the relative economic profitability of an integrated energy system (IES) coupling an NPP with a synfuel production process at selected case study locations across the United States. In the synfuel IES, a high-temperature steam electrolysis (HTSE) plant is thermally and electrically coupled with an NPP to produce zero-carbon hydrogen. The synthetic fuel is produced from this H 2 combined with a CO 2 supply using the reverse water gas shift process followed by the Fischer-Tropsch (FT) reaction. This analysis considers a system in which the CO 2 is sourced from regional CO 2 emitters via the construction and operation of pipeline-based CO 2 supply networks. Locating the FT plant at the same site as the NPP and HTSE plants enables the NPP to provide zero-carbon heat and power to the HTSE plant and zero-carbon power to the FT plant as well as avoid the requirement for long-distance H 2 product transport from the HTSE plant to the FT plant. Hydrogen storage is used to enable the NPP to dispatch power to the electrical grid (instead of the HTSE plant) when grid demand increases, thus enabling the FT plant to continue to operate in a steady-state production mode. The ability to cease hydrogen production for several hours within each day enables the NPP to provide power to the grid to balance the electricity market during peak periods and maximize revenues for the nuclear synfuel IES. The FT process design considered has a 99% carbon conversion efficiency. The use of nuclear energy and nuclear energy-derived hydrogen enables synfuel production to achieve this high level of carbon utilization. Additionally, the life-cycle carbon emissions of the nuclear-based synfuel production process are very low, with WTW emissions of approximately 25 gCO 2 e/MJ, including steam credits (generated from FT process excess heat), and approximately 7 gCO 2 e/MJ, if steam credits are excluded. This compares favorably with the WTW emissions of 90.5 gCO 2 e/MJ for a compression-ignition, direct injection (CIDI) vehicle with a fuel economy of 31.6 miles per gallon gasoline equivalent (MPGGE), using low-sulfur diesel produced using conventional petroleum production and refining processes. Several NPPs in various regions of the U.S. are considered as case study analyses. Supply locations and transportation via pipeline of the CO 2 feedstock to the NPP site are analyzed through the National Energy Technology Laboratory (NETL) CO 2 Transport Cost model. The team finds that the amount of CO 2 generated by different sectors is sufficient for the synfuel production process at all locations considered. The CO 2 transportation costs are functions of the distance of the source to the NPP location, the CO 2 capture cost at the source, and the quantity of CO 2 transported. Historical electricity prices for the NPP case study locations are collected and analyzed. Monthly average prices, price range, and duration of negative-price periods vary among these locations. For each location, an auto-regressive moving average (ARMA) model is trained on historical electricity price data. ARMA validation is done to ensure the synthetic price distributions represent one of historical prices with high fidelity. Synthetic time series from these ARMA models are used in a coupled dispatch and system optimization in the Holistic Energy Resource Optimization Network (HERON) to compute the differential net present value (NPV) of the IES. The team finds that this econometric is positive, ranging from $14M–1.3bn (2020) depending on the location. The optimal synfuel IES configuration to obtain this increase in NPV often maximizes the size of the synfuel production process with regards to the size of the NPP. However, the team shows that the NPP still plays a stabilizing role for the grid: In periods of high prices and high loads, more electricity from the NPP is sent to the grid. A high variability of electricity prices and extreme maximum prices tend to drive up electricity production. While it requires significant investment, the synfuel IES could increase the economic profitability for the existing fleet of LWRs across the country while still maintaining the grid stabilizer role of NPPs. During its lifetime, the main costs for the nuclear synfuel IES are the carbon feedstock transportation costs, followed by the capital expenses (CAPEX) and operation and maintenance (O&M) costs while the revenue comes first from the IRA H 2 production tax credit (PTC) and then from the sales of synfuel products. The profitability of the synfuel IES is most sensitive to the value of the hydrogen PTC and the synfuel products as well as the cost of the carbon feedstock, highlighting the importance of governmental incentives regarding hydrogen, carbon emissions, and synfuel in driving the deployment of future nuclear synfuel IESs.

08 HYDROGEN↗
NASA NTRS1994

Numerical Simulations of High-Speed Chemically Reacting Flow

The Essentially NonOscillatory (ENO) shock-capturing scheme for the solution of hyperbolic equations is extended to solve a system of coupled conservation equations governing two-dimensional, time-dependent, compressible chemically reacting flow with full chemistry. The thermodynamic properties of the mixture are modeled accurately, and stiff kinetic terms are separated from the fluid motion by a fractional step algorithm. The methodology is used to study the concept of shock-induced mixing and combustion, a process by which the interaction of a shock wave with a jet of low-density hydrogen fuel enhances mixing through streamwise vorticity generation. Test cases with and without chemical reaction are explored here. Our results indicate that, in the temperature range examined, vorticity generation as well as the distribution of atomic species do not change significantly with the introduction of a chemical reaction and subsequent heat release. The actual diffusion of hydrogen is also relatively unaffected by the reaction process. This suggests that the fluid mechanics of this problem may be successfully decoupled from the combustion processes, and that computation of the mixing problem (without combustion chemistry) can elucidate much of the important physical features of the flow.

Ton, V. T.↗
NASA NTRS1994

Numerical Simulations of High-Speed Chemically Reacting Flow

The essentially nonoscillatory (ENO) shock-capturing scheme for the solution of hyperbolic equations is extended to solve a system of coupled conservation equations governing two-dimensional, time-dependent, compressible chemically reacting flow with full chemistry. The thermodynamic properties of the mixture are modeled accurately, and stiff kinetic terms are separated from the fluid motion by a fractional step algorithm. The methodology is used to study the concept of shock-induced mixing and combustion, a process by which the interaction of a shock wave with a jet of low-density hydrogen fuel enhances mixing through streamwise vorticity generation. Test cases with and without chemical reaction are explored here. Our results indicate that, in the temperature range examined, vorticity generation as well as the distribution of atomic species do not change significantly with the introduction of a chemical reaction and subsequent heat release. The actual diffusion of hydrogen is also relatively unaffected by the reaction process. This suggests that the fluid mechanics of this problem may be successfully decoupled from the combustion processes, and that computation of the mixing problem (without combustion chemistry) can elucidate much of the important physical features of the flow.

Ton, V. T.↗
DOE OSTI2020

High-temperature superconductivity in LaH 10

The recent discovery of a high critical temperature $T_c$ in compressed H 3 S has been followed by the prediction of Liu et al. of $T_c$ ≈ 250 K in the clathrate LaH 10 structure. This report has been confirmed experimentally by Somayazulu et al. and Drozdov et al. Additional theoretical work by Wang et al. and Quan et al. further established the mechanism of electron-phonon interaction and the dominant role of hydrogen. In the present Rapid Communication we follow the classic McMillan paper, which separates the electron and phonon contributions to the electron-phonon coupling λ. We first compute the numerator of McMillan's expression, the Hopfield parameter η, using the theory of Gaspari and Gyorffy (GG), and obtain the force constants in the denominator from Wang et al. and Quan et al. The resulting λ is used in the Allen-Dynes equation to calculate $T_c$. The value of $T_c$ reaches a maximum in the range of 236–263 K at pressures of 255 GPa and decreases for smaller or larger pressures. Further, we provide a thorough analysis of the different terms of the GG equation and draw the conclusion that the $\textit{sp}$ channel of the hydrogen is the most important contribution to obtain high values of $T_c$ in this material. Consistent with Wang et al., we find large values of λ that decrease with increasing pressure. In addition, we find that the hydrogen sites are the largest contributors to the total value of the coupling constant λ. That is, the acoustic mode associated with La contributes only 2% to the total λ, while the optic modes associated with H contribute 18% for the H1 site and 80% for the H2 site. These relative contributions to λ are consistent with those given by Wang et al. and by Quan et al. Thus, our results strongly support the view that LaH 10 is a metallic hydrogen superconductor.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS2004

Automated Processing of ISIS Topside Ionograms into Electron Density Profiles

Modeling of the topside ionosphere has for the most part relied on just a few years of data from topside sounder satellites. The widely used Bent et al. (1972) model, for example, is based on only 50,000 Alouette 1 profiles. The International Reference Ionosphere (IRI) (Bilitza, 1990, 2001) uses an analytical description of the graphs and tables provided by Bent et al. (1972). The Alouette 1, 2 and ISIS 1, 2 topside sounder satellites of the sixties and seventies were ahead of their times in terms of the sheer volume of data obtained and in terms of the computer and software requirements for data analysis. As a result, only a small percentage of the collected topside ionograms was converted into electron density profiles. Recently, a NASA-funded data restoration project has undertaken and is continuing the process of digitizing the Alouette/ISIS ionograms from the analog 7-track tapes. Our project involves the automated processing of these digital ionograms into electron density profiles. The project accomplished a set of important goals that will have a major impact on understanding and modeling of the topside ionosphere: (1) The TOPside Ionogram Scaling and True height inversion (TOPIST) software was developed for the automated scaling and inversion of topside ionograms. (2) The TOPIST software was applied to the over 300,000 ISIS-2 topside ionograms that had been digitized in the fkamework of a separate AISRP project (PI: R.F. Benson). (3) The new TOPIST-produced database of global electron density profiles for the topside ionosphere were made publicly available through NASA s National Space Science Data Center (NSSDC) ftp archive at . (4) Earlier Alouette 1,2 and ISIS 1, 2 data sets of electron density profiles from manual scaling of selected sets of ionograms were converted fiom a highly-compressed binary format into a user-friendly ASCII format and made publicly available through nssdcftp.gsfc.nasa.gov. The new database for the topside ionosphere established as a result of this project, has stimulated a multitude of new studies directed towards a better description and prediction of the topside ionosphere. Marinov et al. (2004) developed a new model for the upper ion transition height (Oxygen to Hydrogen and Helium) and Bilitza (2004) deduced a correction term for the I N topside electron density model. Kutiev et al. (2005) used this data to develop a new model for the topside ionosphere scale height (TISH) as a function of month, local time, latitude, longitude and solar flux F10.7. Comparisons by Belehaki et al. (2005) show that TISH is in general agreement with scale heights deduced from ground ionosondes but the model predicts post-midnight and afternoon maxima whereas the ionosonde data show a noon maximum. Webb and Benson (2005) reported on their effort to deduce changes in the plasma temperature and ion composition from changes in the topside electron density profile as recorded by topside sounders. Limitations and possible improvements of the IRI topside model were discussed by Coisson et al. (2005) including also the possible use of the NeQuick model, Our project progressed in close collaboration and coordination with the GSFC team involved in the ISIS digitization effort. The digitization project was highly successful producing a large amount of digital topside ionograms. Several no-cost extensions of the TOPIST project were necessary to keep up with the pace and volume of the digitization effort.

Reinisch, bodo W.↗
DOE OSTI2020

First-principles study of hydrogen behavior near W/WC interfaces

Hydrogen (H) solution, migration, and binding to vacancies near the tungsten/tungsten carbide (W/WC) interfaces based on hcp WC or bcc W (W/WCb and Wb/WC) have been studied by first-principles simulations to provide insights into the effect of C on H behavior in W exposed to C deposition in fusion reactors. The H behavior near the W/WC interfaces is related to the tensile or compressive strain due to the lattice match and interfacial effects. Near the W/WCb interface, the H solution energy in hcp WC increases approaching the interface, while it decreases from the W side to the interface. The configuration change of the W slab significantly decreases the H solution energy but has only a modest effect on the H migration energy barrier in comparison with the values in bcc W. The interface enhances the H binding to vacancies in WC layers. Both the interface and configuration adjustment of the W slab reduce the H binding to vacancies on the W side of the interface. Near the Wb/WC interface, H solution energies in both WC and W slabs weakly decrease approaching the interface. The configuration change of the WC slab significantly increases the H solution energy and binding energy to vacancies but decreases the H migration energy barrier in comparison with the values in hcp WC. The H energetics near the W/WC interfaces indicate the likelihood of H localization and diffusion in the W side of the interface, rather than diffusing through the interface into WC layers.

Yang, L. (ORCID:0000000322166071)↗
DOE OSTI2023

The equations of state of statically compressed palladium and rhodium

Here, the pressure–volume equations of state of palladium and rhodium statically compressed in neon are presented. Vinet fits give parameters for palladium: V0=58.678(73) Å 3 , B 0 =189.3(30) GPa, B' 0 =5.473(63), and rhodium: V 0 =55.062(63) Å3, B 0 =241.3(65) GPa, B' 0 =5.34(24). Both metals are observed to react with hydrocarbons under pressure to form hydrides. Existing equations of state are discussed with regard to potential inadvertent hydrogen contamination as a source for discrepancies and anomalous fitted parameters.

36 MATERIALS SCIENCE↗
NASA NTRS2010

Silica/Polymer and Silica/Polymer/Fiber Composite Aerogels

Aerogels that consist, variously, of neat silica/polymer alloys and silica/polymer alloy matrices reinforced with fibers have been developed as materials for flexible thermal-insulation blankets. In comparison with prior aerogel blankets, these aerogel blankets are more durable and less dusty. These blankets are also better able to resist and recover from compression . an important advantage in that maintenance of thickness is essential to maintenance of high thermal-insulation performance. These blankets are especially suitable as core materials for vacuum- insulated panels and vacuum-insulated boxes of advanced, nearly seamless design. (Inasmuch as heat leakage at seams is much greater than heat leakage elsewhere through such structures, advanced designs for high insulation performance should provide for minimization of the sizes and numbers of seams.) A silica/polymer aerogel of the present type could be characterized, somewhat more precisely, as consisting of multiply bonded, linear polymer reinforcements within a silica aerogel matrix. Thus far, several different polymethacrylates (PMAs) have been incorporated into aerogel networks to increase resistance to crushing and to improve other mechanical properties while minimally affecting thermal conductivity and density. The polymethacrylate phases are strongly linked into the silica aerogel networks in these materials. Unlike in other organic/inorganic blended aerogels, the inorganic and organic phases are chemically bonded to each other, by both covalent and hydrogen bonds. In the process for making a silica/polymer alloy aerogel, the covalent bonds are introduced by prepolymerization of the methacrylate monomer with trimethoxysilylpropylmethacrylate, which serves as a phase cross-linker in that it contains both organic and inorganic monomer functional groups and hence acts as a connector between the organic and inorganic phases. Hydrogen bonds are formed between the silanol groups of the inorganic phase and the carboxyl groups of the organic phase. The polymerization process has been adapted to create interpenetrating PMA and silica-gel networks from monomers and prevent any phase separations that could otherwise be caused by an overgrowth of either phase. Typically, the resulting PMA/silica aerogel, without or with fiber reinforcement, has a density and a thermal conductivity similar to those of pure silica aerogels. However, the PMA enhances mechanical properties. Specifically, flexural strength at rupture is increased to 102 psi (=0.7 MPa), about 50 times the flexural strength of typical pure silica aerogels. Resistance to compression is also increased: Applied pressure of 17.5 psi (=0.12 MPa) was found to reduce the thicknesses of several composite PMA/silica aerogels by only about 10 percent.

Ou, Danny↗
DOE OSTI2021

End-gas autoignition fraction and flame propagation rate in laser-ignited primary reference fuel mixtures at elevated temperature and pressure

Knock in spark-ignited (SI) engines is initiated by autoignition of the unburned gasses upstream of spark-ignited, propagating, turbulent premixed flames. Knock propensity of fuel/air mixtures is typically quantified using research octane number (RON), motor octane number (MON), or methane number (MN; for gaseous fuels), which are measured using single-cylinder, variable compression ratio engines. In this study, knock propensity of SI fuels was quantified via observations of end-gas autoignition (EGAI) in unburned gasses upstream of laser-ignited, premixed flames at elevated pressures and temperatures in a rapid compression machine. Stoichiometric primary reference fuel (PRF; n-heptane/isooctane) blends of varying reactivity (50 ≤ PRF ≤ 100) were ignited using an Nd:YAG laser over a range of temperatures and pressures, all in excess of 545 K and 16.1 bar. Laser ignition produced outwardly-propagating premixed flames. High-speed pressure measurements and schlieren images indicated the presence of EGAI. The fraction of the total heat release attributed to EGAI (i.e., EGAI fraction) varied with fuel reactivity (i.e., octane number) and the time-integrated temperature of the end-gas prior to ignition. Flame propagation rates, which were measured using schlieren images, were only weakly correlated with octane number but were affected by turbulence caused by variation in piston timing. Under conditions of low turbulence, measured flame propagation rates approached one-dimensional premixed laminar flame speed computations performed at the same conditions. Experiments were simulated with a three-dimensional CONVERGE™ model using reduced chemical kinetics (121 species, 538 reactions). The simulations accurately captured the measured flame propagation rates, as well as the variation in EGAI fraction with fuel reactivity and time-integrated end-gas temperature. The simulations also revealed low-temperature heat release as well as formaldehyde and hydrogen peroxide formation in the end-gas upstream of the propagating flame, which increased the temperature and degree of chain branching in the end-gas, ultimately leading to EGAI.

42 ENGINEERING↗
DOE OSTI2021

First observation of increased DT yield over prediction due to addition of hydrogen

Here, in a number of reported instances, implosions utilizing fuel mixtures have resulted in anomalously low fusion yields below those predicted by radiation-hydrodynamics simulations. Inter-species ion diffusion has been suggested as a possible cause of the observed yield degradation in fuel mixture implosions. An experimental platform utilizing hydro-equivalent deuterium–tritium (DT), deuterium–tritium–hydrogen (DTH), and deuterium-tritium-helium3 (DT 3 He) capsule implosions was developed to determine whether the inter-species ion diffusion theory may describe the resulting fuel mixture implosion behavior. The implosion experiments were performed at the Omega laser facility. X-ray images and shell areal density diagnostics results show that the hydro-equivalent three capsules (DT, DTH, and DT 3 He) have similar compression behavior. However, nuclear yield deviation was observed from the scaling determined using a fusion yield formula. In the DT 3 He mixture, a reduced yield of a factor of 0.65 ± 0.13 was observed, which is similar to a yield reduction observed in D 3 He mixture by Rygg et al. (i.e., Rygg effect). In contrast, in the DTH mixture, a factor of 1.17 ±0.15 yield increase was observed, which we named the inverse Rygg effect. The yield increase observed in the DTH mixture is consistent with the inter-species ion diffusion theory where lighter H diffuses away from the core and concentrated DT in the core produces higher yield. An inter-species ion diffusion model, the Zimmerman–Paquette–Kagan–Zhdanov model, implemented in a Lagrangian radiation-hydrodynamics fluid code, was also used to analyze the present data, without the need to assume hydrodynamic equivalence of the capsules, but it does not completely explain the DTH or DT 3 He capsules although its effects are in the correct direction. Simulation-based Bayesian inference was used in the latter analysis to quantify the uncertainty in the numerical simulations. The simulation-based analysis resulted in an inferred Rygg-effect yield decrease factor of 0.91 ± 0.02 for the DT 3 He mixture, and an inferred inverse-Rygg yield increase factor of 1.21 ± 0.04 for the DTH mixture, based on simulations ignoring ion diffusion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1986

The far-infrared and optical structure of Arp 220

The spatial structure of the luminous peculiar galaxy Arp 220 has been investigated in the far infrared. The results reveal that most of the luminosity is from a source less than 3 kpc in extent, located in the nuclear region of the galaxy. The size constraints yield a lower limit of 0.05 for the 100 micron optical depth, implying a hydrogen column density over 5 x 10 to the 22nd/sq cm. New optical images confirm that the double-lobed optical appearance results from strong absorption across the true nucleus. Arp 220 exhibits three primary features which provide strong evidence for an external source of energy: (1) a chaotic and highly asymmetric galactic halo; (2) a large internal velocity dispersion in CO and H I; and (3) extreme compression of gas and dust. These features are natural consequences of previously proposed models which invoke a direct galactic collision and merger, and are unlikely to result from a long-range tidal interaction with the neighboring galaxy IC 4554.

Joy, M.↗
NASA NTRS2017

Atmospheric Capture On Mars (and Processing)

The ultimate destination of NASA's human exploration program is Mars. In Situ Resource Utilization (ISRU) is a key technology required to enable such missions, as first proposed by Prof. Robert Ash in 1976. This presentation will review progress in the systems required to produce rocket propellant, oxygen, and other consumables on Mars using the carbon dioxide atmosphere and other potential resources. For many years, NASA, commercial companies, and academia have been developing, and demonstrating techniques to capture and purify Martian atmospheric gases for their utilization for the production of hydrocarbons, oxygen, and water in ISRU systems. Other gases will be required to be separated from Martian atmospheric gases to provide pure CO2 for processing elements. Significant progress has been demonstrated in CO2 collection via adsorption by molecular sieves, freezing, and direct compression. Early stage work in adsorption in Ionic Liquids followed by electrolysis to oxygen is also underway. In addition, other Martian gases, such as nitrogen and argon, occur in concentrations high enough to be useful as buffer gas and could be captured as well. Gas separation requirements include, but are not limited to the selective separation of: (1) methane and water from unreacted carbon oxides (CO2-CO) and hydrogen typical of a Sabatier-type process, (2) carbon oxides and water from unreacted hydrogen from a Reverse Water-Gas Shift process, and (3) carbon oxides from oxygen from a trash/waste processing reaction.

propellant production↗
DOE OSTI2020

Low Temperature Oxidation of Methylpropyl Ether

Ethers are potential high-performance fuels that can be produced from renewable carbon sources such as biomass, but their combustion properties are not clearly understood. The cetane numbers (CN) for ethers, a measure of autoignition tendency, can range from less than 10 to greater than 100, and predictive tools based upon the molecular structures are desirable in order to focus fuel development research. In this study, we used molecular modeling, chemical kinetic modeling, and experimental measurements to understand the important reactions that lead to the autoignition of methylpropyl ether (MPE), a model for ethers containing alkyl chains long enough for intramolecular hydrogen transfer. These reactions are known to be important in the autoignition of alkanes and ethers and we propose to investigate the relationship between alkyl and ether reaction pathways. A reaction mechanism for MPE was created using MIT's Reaction Mechanism Generator (RMG) and G4 quantum calculation results and models were tested using the ChemKin Pro suite of software. Results from atmospheric pressure, flow tube reactor experiments and rapid compression machine (RCM) experiments were used to test the kinetic model and suggest refinements.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Temperature controlled transformations of giant unilamellar vesicles of amphiphilic triblock copolymers synthesized via microfluidic mixing

We report on a simple approach for synthesis of temperature-responsive giant unilamellar vesicles (GUVs) from poly(N-vinylcaprolactam) 15 -block-poly(dimethylsiloxane) 65 -block-poly(N-vinylcaprolactam) 15 (PVCL 15 -PDMS65-PVCL 15 ) triblock copolymer and non-temperature responsive small and giant vesicles from novel poly(N-vinylpyrrolidone)-block-poly(dimethylsiloxane)-block-poly(N-vinylpyrrolidone) (PVPON 15 -PDMS 65 -PVPON 15 and PVPON 6- PDMS 30- PVPON 6 ) triblock copolymers using microfluidic mixing at 25 °C. We show that temperature-responsive PVCL 15 -PDMS 65- PVCL 15 GUVs with the average diameter of 1.4 ± 0.2 µm while being stable at room temperature for at least 14 days, transformed irreversibly into small vesicles of 168 ± 40 nm after incubation of their aqueous solution at 42 °C for 24 h. We hypothesized that this transformation is induced by local compressive stresses of the vesicle membrane due to the collapse of PVCL blocks above the copolymer lower critical solution temperature (LCST) leading to the decrease of the vesicle membrane thickness. Consequently, we found that the temperature-induced size transformation of the PVCL-based GUVs at 42°C can be suppressed by substituting PVCL with its hydrophilic homologue PVPON, or by suppressing the PVCL's LCST behavior through hydrogen-bonding with tannic acid molecules. In the former case, novel PVPON n -PDMS m -PVPON n triblock copolymers (n = 15, m = 65 and n = 6, m = 30) assemble into vesicles stable from 25 °C to 55 °C as confirmed by optical and electron microscopy, dynamic light scattering (DLS) and small-angle neutron scattering (SANS). In the latter, hydrogen bonding interactions of PVCL with the polyphenol tannic acid (TA) at room temperature resulted in stable PVCL-based GUVs at 42°C as confirmed by optical, electron, and atomic force microscopies. We also found that physical crosslinking of the PVCL corona through hydrogen bonding with TA in PVCL 15- PDMS 65- PVCL 15 GUVs will delay their low pH-induced degradation at 37°C by 48 h compared to non-modified GUVs. Our findings open opportunities for the development of temperature-regulated stable micro-vehicles that would change their structural characteristics in the physiologically relevant temperature range from 25 to 42°C and can be utilized for cell mimicking studies. The developed GUVs also have potential in theranostic drug delivery as substitutes for polymer microcapsules and lipid microbubbles as well as for stimuli-triggered sensing, protection, and rapid response in an aqueous environment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Bioblendstocks to Optimize Mixing Controlled Compression Ignition (MCCI) Engines

In this project, a team of researchers from the University of Massachusetts Lowell, the University of Maine, and Mainstream Engineering developed an integrated process for the product of bioblendstocks to optimize mixing controlled compression ignition (MCCI) engines. The objective was to improve the energy density, sooting propensity, and cetane number of base diesel fuel while maintaining cold weather behavior. The process converts woody biomass (e.g. sawmill residues) into bio-oil through selective fast pyrolysis; the bio-oil is then selectively upgraded to form selectively oxygenated, minimally-branched hydrocarbons using non-noble metal catalysts in combination with metal-catalyzed hydrogenation. Advanced predictive models, in conjunction with existing property databases, and experimental testing are used to evaluate overall bioblendstock properties and their impact on base diesel fuel. An iterative, targeted upgrading approach was implemented to optimize the proposed bioblendstock’s properties. Assessment methodologies included techno-economic analysis, life-cycle assessment, property testing, and engine testing. Ultimately, the project team successfully produced a viable bioblendstock while identifying critical process points related to scale-up efforts. It was found that producing pyrolysis oils at 500 degrees C and with pine particle sizes of 1-2 mm led to bio-oil with a higher yield (of approximately 45 wt%) and rich amounts of aromatic alcohols. The resultant pyrolysis oil was then upgraded using a sequence of mild hydrotreating, followed by catalytic etherification and esterification, followed by another final mild hydrotreating to produce a blendstock containing saturated species with a limited, but non-zero, amount of oxygen. The aromatic alcohols produced by pyrolysis were especially helpful in this regard, as the resulting bicycloethers and derivatives exhibited high cetane numbers. While most bulk properties of the bioblendstock met or exceeded targeted thresholds, viscosity and cloud point notably fell outside the expected range; this could be addressed by blending limits and/or through the use of additives that are commonplace in current refinding practices. Identification of a bioblendstock that can be produced economically at scale while improving the performance and emissions characteristics of internal combustion engines positively affects the economy by boosting domestic fuel production and the environment by decreasing harmful emissions and increasing efficiency.

09 BIOMASS FUELS↗
NASA NTRS1981

Two-component Fermi-liquid theory - Equilibrium properties of liquid metallic hydrogen

It is reported that the transition of condensed hydrogen from an insulating molecular crystal phase to a metallic liquid phase, at zero temperature and high pressure, appears possible. Liquid metallic hydrogen (LMH), comprising interpenetrating proton and electron fluids, would constitute a two-component Fermi liquid with both a very high component-mass ratio and long-range, species-dependent bare interactions. The low-temperature equilibrium properties of LMH are examined by means of a generalization to the case of two components of the phenomenological Landau Fermi-liquid theory, and the low-temperature specific heat, compressibility, thermal expansion coefficient and spin susceptibility are given. It is found that the specific heat and the thermal expansion coefficient are vastly greater in the liquid than in the corresponding solid, due to the presence of proton quasiparticle excitations in the liquid.

Oliva, J.↗
NASA NTRS1988

Wave processes in scramjet thrust generation

The investigation explores the steady, supersonic expansion and compression wave processes involved in generating thrust from a combustion jet in a two-dimensional scramjet. Two types of thrust generating wave are produced by the jet. The first is the injection compression waves associated with injection and combustion of the fuel, and the second is the expansion interaction waves associated with interaction between the exhaust nozzle expansion and the jet. Analysis shows that the strength of a wave is not modified by crossing the jet, which implies that, with a given flow configuration, the jets in a multiple jet combustion array produce thrust independently of one another. Shock tunnel experiments with hydrogen fuel and three simple scramjet configurations are used to identify the two types of waves, to confirm the effect on a wave of crossing the jet, and to demonstrate the influence of the basic, fuel-off flow configuration on the effects produced by the waves.

Stalker, R. J.↗
DOE OSTI2025

Investigation of the Mechanical Degradation of Zinc-Based Cold Spray Coatings for Steel Pipelines

Internal corrosion in wet natural gas is a big challenge in the oil and gas industry due to corrosive constituents such as carbon dioxide (CO2), hydrogen sulfide (H2S), other forms of sulfur, and water in the gas stream. To mitigate internal corrosion, zinc-based cold spray coatings were designed for use in natural gas pipelines to increase the lifespan of the pipeline network. However, one of the requirements in designing internal coatings is the resistance of the coatings to mechanical forces applied on the pipeline's internal wall during pigging operations. These forces are primarily compressive and shear/friction forces. This study examines material properties that must be considered when evaluating mechanical considerations.

adhesion↗