Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “glass fiber”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Research on graphite reinforced glass matrix composites

The results of research for the origination of graphite-fiber reinforced glass matrix composites are presented. The method selected to form the composites consisted of pulling the graphite fiber through a slurry containing powdered glass, winding up the graphite fiber and the glass it picks up on a drum, drying, cutting into segments, loading the tape segment into a graphite die, and hot pressing. During the course of the work, composites were made with a variety of graphite fibers in a glass matrix.

Bacon, J. F.↗
NASA NTRS1996

Effects of Fiber Content on Mechanical Properties of CVD SiC Fiber-Reinforced Strontium Aluminosilicate Glass-Ceramic Composites

Unidirectional CVD SiC(f)(SCS-6) fiber-reinforced strontium aluminosilicate (SAS) glass-ceramic matrix composites containing various volume fractions, approximately 16 to 40 volume %, of fibers were fabricated by hot pressing at 1400 C for 2 h under 27.6 MPa. Monoclinic celsian, SrAl2Si2O8, was the only crystalline phase formed, with complete absence of the undesired hexacelsian phase, in the matrix. Room temperature mechanical properties were measured in 3-point flexure. The matrix microcracking stress and the ultimate strength increased with increase in fiber volume fraction, reached maximum values for V(sub f) approximately equal to 0.35, and degraded at higher fiber loadings. This degradation in mechanical properties is related to the change in failure mode, from tensile at lower V(sub f) to interlaminar shear at higher fiber contents. The extent of fiber loading did not have noticeable effect on either fiber-matrix debonding stress, or frictional sliding stress at the interface. The applicability of micromechanical models in predicting the mechanical properties of the composites was also examined. The currently available theoretical models do not appear to be useful in predicting the values of the first matrix cracking stress, and the ultimate strength of the SCS-6/SAS composites.

Bansal, Narottam P.↗
NASA NTRS1977

Research on Graphite Reinforced Glass Matrix Composites

This report contains the results obtained in the first twelve months of research under NASA Langley Contract NAS1-14346 for the origination of graphite-fiber reinforced glass matrix composites. Included in the report is a summary of the research by other investigators in this area. The method selected to form the composites consisted of pulling the graphite fiber through a slurry containing powdered glass, winding up the graphite fiber and the glass it picks up on a drum, drying, cutting into segments, loading the tape segment into a graphite die, and hot pressing. During the course of the work, composites were made with a variety of graphite fibers in a C.G.W. 7740 (Pyrex) glass matrix. The graphite fibers used included Hercules HMS, Hercules HTS, Thornel 300S, and Celanese DG-102 and, of these, the Hercules HMS and Celanese DG-102 graphite fibers in C.G.W. 7740 gave the most interesting but widely different results. Hercules HMS fiber in C.G.W. 7740 glass (Pyrex) showed an average four-point flexural strength of 848 MPa or 127,300 psi. As the test temperature was raised from room temperature to 560 C in argon or vacuum, the strength was higher by 50 percent. However, in air, similar tests at 560 C gave a severe loss in strength. These composites also have good thermal cycle properties in argon or vacuum, greatly increased toughness compared to glass, and no loss in strength in a 100 cycle fatigue test. Celanese DG-102 fiber in C.G.W. 7740 glass (Pyrex) had a much lower flexural strength but did not suffer any loss in this strength when samples were heated to 560 C in air for 4 hrs.

Bacon, J. F.↗
NASA NTRS1990

Fourier transform infrared (FTIR) fiber optic monitoring of composites during cure in an autoclave

Real-time in situ monitoring of the chemical states of epoxy resins was investigated during cure in an autoclave using infrared evanescent spectroscopy. Fiber evanescent sensors were developed which may be sandwiched between the plies of the prepreg sample. A short length of sapphire fiber was used as the sensor cell portion of the fiber probe. Heavy metal fluoride glass optical fiber cables were designed for connecting the FTIR spectrometer to the sensor fiber within the autoclave. The sapphire fibers have outstanding mechanical thermal properties which should permit their use as an embedded link in all thermoset composites. The system is capable of operation at a temperature of 250 C for periods up to 8 hours without major changes to the fiber transmission. A discussion of the selection of suitable sensor fibers, the construction of a fiber-optic interface, and the interpretation of in situ infrared spectra of the curing process is presented.

Druy, Mark A.↗
DOE OSTI2021

Influence of Fiber Orientation on Deformation of Additive Manufactured Composites

Anisotropy caused by flow-induced fiber orientation of discontinuous fibers within the extrudate in the Extrusion Deposition Additive Manufacturing (EDAM) process gives rise to anisotropic shrinkage in printed parts and thereby, final part deformations. Three fiber orientation states, described by the second-order orientation tensor, were investigated to determine their influence upon final geometry. Two material systems were investigated including a short glass fiber-reinforced polyamide and a short carbon fiber-reinforced polyamide. A curvilinear geometry was modeled and printed virtually in the thermo-mechanical simulation, ADDITIVE3D©. The scale of the printed geometry was in the range of 300–400 mm and contained three semicircular geometry regions connected to linear regions, thereby inducing significant magnification of the spring-in deformation. The predicted deformation of the printed geometry for the three fiber orientation states and two material systems were compared. The deformation predicted for glass fiber-filled polyamide and carbon fiber-filled polyamide of the same fiber orientation states showed comparable deformations. In conclusion, the largest residual deformation was shown to correspond to the orientation tensor with the greatest degree of anisotropy.

36 MATERIALS SCIENCE↗
NASA NTRS1992

Silicon carbide fiber reinforced strontium aluminosilicate glass-ceramic matrix composite

A SrO-Al2O3 - 2SrO2 (SAS) glass ceramic matrix is reinforced with CVD SiC continuous fibers. This material is prepared by casting a slurry of SAS glass powder into tapes. Mats of continuous CVD-SiC fibers are alternately stacked with the matrix tapes. This tape-mat stack is warm-pressed to produce a 'green' composite. Organic constituents are burned out of the 'green' composite, and the remaining interim material is hot pressed.

Bansal, Narottam↗
NASA NTRS1995

Method of producing a silicon carbide fiber reinforced strontium aluminosilicate glass-ceramic matrix composite

A SrO-Al2O3-2SrO2 (SAS) glass ceramic matrix is reinforced with CVD SiC continuous fibers. This material is prepared by casting a slurry of SAS glass powder into tapes. Mats of continuous CVD-SiC fibers are alternately stacked with the matrix tapes. This tape-mat stack is warm-pressed to produce a 'green' composite. Organic constituents are burned out of the 'green' composite, and the remaining interim material is hot pressed.

Bansal, Narottam P.↗
NASA NTRS1986

Thermal stability of lightweight graphite glass sandwich reflectors for far infrared astronomy

Graphite fiber-reinforced glass matrix composites are being developed for a variety of structural applications requiring excellent thermomechanical stability. These materials are ideally suited for lightweight, high strength, thermally stable infrared mirrors because of their low density, low thermal expansion, high strength and stiffness, and their ability to be machined, replicated and figured using standard polishing techniques. These properties are particularly promising for applications such as a 3-meter balloon-borne far-infrared and submillimeter telescope mirror which must be both very lightweight and able to retain its figure accuracy when cycled between room temperature and its operating temperature of -50 C. This paper presents the results of a set of low temperature optical tests conducted to determine the figure stability of a 30-cm diameter, frit-bonded graphite/glass mirror in the +20 to -60 C temperature range using a 10.6 micron laser interferometer. The results indicate that the residual change in figure was less than 0.3 microns, rms.

Bluege, J. H.↗
DOE OSTI2021

Controlled Pyrolysis: A Robust Scalable Composite Recycling Technology

The reinforced composites industry is facing significant challenges in handling the scrap composite material from automobile manufacturing, the wind turbine industry, and others. The fibers in the material, whether they be carbon, glass, or other materials have commercial value if they can be recovered successfully. Successfully means the fibers are clean with no sizing or other binders and have adequate strength and physical properties that would allow them to be economically reprocessed into valuable product. The composites recycling project was an industry-collaborative effort to develop a composite recycling technology using controlled pyrolysis. Through the recycling of scrap and end-of-life (EOL) cured composite materials, this pilot study was intended to create a business case by realizing a cost-effective means for recycling EOL and production scrap composite materials, ultimately reducing the volume of composite materials destined for landfill. The project was led by the Institute for Advanced Composites Manufacturing Innovation (IACMI), the American Composites Manufacturers Association (ACMA), Oak Ridge National Laboratory (ORNL), Continental Structural Plastics (CSP) a Teijin Group Company, CHZ Technologies, and A. Schulman with support from Owens Corning, John Deere, General Electric (GE), Ashland LLC, and Plastics Europe (CEFIC). The team studied and tested CHZ Technologies’ controlled pyrolysis system, known as the Thermolyzer TM , which operates on a scalable basis to convert organic polymer materials into a clean synthesis gas and char containing the recoverable carbon and glass fiber reinforcement. The recoverable energy contained in the input polymers creates the synthesis gas that can be used to provide heat to the Thermolyzer TM primary reactor in a sustainable manner. That is, once the Thermolyzer TM is started with a small amount of external natural gas, the synthesis gas that is created from the polymers will continue to operate the burners so long as feedstock is supplied. The reinforcing fiber materials remaining in the solid phase char were separated and cleaned for re-use in other polymer systems based on the retained properties of the fibers. The study created reports (attached in the appendix) on the Mass and Energy Balances, syngas analytics, VOC assessment, yield analysis and other analytics necessary for a Techno-Economic Analysis (TEA) to quantify the economic impact of the recovery and sustainable re-use of the carbon and glass fibers. The process consisted of 4 steps: Selection of 4 samples of cured composite waste materials from project partners interested in materials recycling and recovering the reinforcing fibers for best case re-use. The materials included glass fiber (GF) polyester/vinyl ester automotive SMC from CSP, GF epoxy balsa/PVC foam wind blades from GE, carbon fiber (CF) epoxy wind blade laminated spar caps from GE, and GF/CF epoxy hybrid assembly from John Deere. Processing the waste composite samples into 1-2” shreds. Packaging the shredded composites into bulk sacks on international shipping pallets for shipment to KUG in Forst (Lausitz), Germany. Pyrolysis of the shredded composites under controlled conditions designed for each polymer system. Collecting samples of the gas and char for analysis. Shipping the char containing the CF/GF back to the US for the next steps of testing the fibers and developing protocols for sustainable re-use of the fibers in composite applications.

36 MATERIALS SCIENCE↗
NASA NTRS2001

Utilization of Infrared Fiber Optic in the Automotive Industry

Fiber optics are finding a place in the automotive industry. Illumination is the primary application today. Soon, however, fiber optics will be used for data communications and sensing applications. Silica fiber optics and plastic fibers are sufficient for illumination and communication applications however, sensing applications involving high temperature measurement and remote gas analysis would benefit from the use of infrared fiber optics. Chalcogonide and heavy metal fluoride glass optical fibers are two good candidates for these applications. Heavy metal fluoride optical fibers are being investigated by NASA for applications requiring transmission in the infrared portion of the electromagnetic spectrum. Zirconium-Barium-Lanthanum-Aluminum-Sodium-Fluoride (ZBLAN) is one such material which has been investigated. This material has a theoretical attenuation coefficient 100 times lower than that of silica and transmits into the mid-IR. However, the measured attenuation coefficient is higher than silica due to impurities and crystallization. Impurities can be taken care of by utilizing cleaner experimental protocol. It has been found that crystallization can be suppressed by processing in reduced gravity. Fibers processed in reduced gravity on the KC135 reduced gravity aircraft were found to be free of crystals while those processed on the ground were found to have crystals. These results will be presented along with plans for producing continuous lengths of ZBLAN optical fiber on board the International Space Station.

Tucker, Dennis S.↗
DOE OSTI2020

Study on Fracture of Fiber-Reinforced Polymeric Composites Using Spiral Notch Torsion Test

Fiber-reinforced polymer-matrix composites have been widely applied in various areas due to their excellent mechanical properties. In this study, carbon fiber-reinforced polymer-matrix composites and glass fiber-reinforced polymer-matrix composites failure tests under quasi static torsion have been demonstrated by using spiral notch torsion test methodology. Three types of cylindrical specimens with different fiber orientations were prepared and tested. For both composites, after increase stage, A type exhibited limited stress variations before the sudden failure, whereas B type showed gradual failure with torque drops. Displacement contours, stress contours and energy release rates were acquired using the anisotropic elastic finite element models. Microscopic characterization exhibited that the failure of A type occurred along interfaces between fibers and matrices, whereas circular cracks in B type propagated alternatively between polymeric matrices and interfaces. Type C failure is similar to type A whereas with a curvature observed on the fracture surface.

Du, Fen↗
DOE OSTI2023

Applying protective coatings to optical fibers

Apparatus, systems, and methods that provide coats on a glass optical fiber including of an inner layer and an outer layer. The method includes two steps. First, a conductive polymer coating is applied to the optical fiber as it is being produced. Second, a protective coating is applied to that conductive polymer coating. The conductive polymer coating is applied immediately after the fiber is drawn from preform to fiber.

Calta, Nicholas P.↗
DOE OSTI2023

Low-Velocity Impact Performances of Healed Polymer Fiber Reinforced Plastics

Extending the lifecycle of traditional carbon or glass fiber-reinforced plastics is a complicated problem. The lack of sustainability limits the applications of the traditional composite materials in the vehicle industries where recycling and repurposing are critical issues. Alternatives for the low-stressed structural components are polymer fiber-reinforced plastics (PFRPs). In PFRPs, both the fibers and matrix are composed of thermoplastic polymers (e.g. polypropylene or polyethylene). They are lightweight, easy to manufacture, and cost-effective. Additionally, recycling and repurposing thermoplastic polymers are well understood. Therefore, the PFRPs have strong advantages compared to the traditional fiber-reinforced composites in low-stressed structural applications. In this study, we investigated the low-velocity impact (LVI) performances of the PFRPs and compared them with carbon fiber-reinforced plastics (CFRPs). A semi-spherical impactor was dropped to flat, square panels, and the absorbed impact energy was measured. The damage mechanisms were examined using a Xray µCT scan. The PFRPs outperformed the CFRPs in terms of perforation energy normalized by plate thickness and density. After the perforation, we healed the fractured plates by leveraging the recyclability of the thermoplastic polymers. The healing process of the panels was identical to the initial panel manufacturing process. No additional materials were added during the healing process. The healed PFRP panels were impacted again and substantially recovered energy absorption capability. We also conducted the repeated-impact test with several different impact energies. Unlike the CFRPs where the impact peak load decreased as the impacts repeated, the PFRPs showed an increasing trend. Such a unique mechanism was due to the strain-hardening behavior of the polymer fibers and matrix. As a result, the repeated-impact life of the PFRPs was significantly enhanced. These results are particularly interesting in the automotive or aerospace industries where repeated LVI is frequently observed.

Ko, Seunghyun↗
NASA NTRS1980

Research on graphite reinforced glass matrix composites

High levels of mechanical performance in tension, flexure, fatigue, and creep loading situations of graphite fiber reinforced glass matrix composites are discussed. At test temperatures of up to 813 K it was found that the major limiting factor was the oxidative instability of the reinforcing graphite fibers. Particular points to note include the following: (1) a wide variety of graphite fibers were found to be comparable with the glass matrix composite fabrication process; (2) choice of fiber, to a large extent, controlled resultant composite performance; (3) composite fatigue performance was found to be excellent at both 300 K and 703 K; (4) composite creep and stress rupture at temperatures of up to 813 K was limited by the oxidative stability of the fiber; (5) exceptionally low values of composite thermal expansion coefficient were attributable to the dimensional stability of both matrix and fiber; and (6) component fabricability was demonstrated through the hot pressing of hot sections and brazing using glass and metal joining phases.

Prewo, K. M.↗
NASA NTRS1994

Ceramic fiber-reinforced monoclinic celsian phase glass-ceramic matrix composite material

A hyridopolysilazane-derived ceramic fiber reinforced monoclinic celsian phase barium aluminum silicate glass-ceramic matrix composite material is prepared by ball-milling an aqueous slurry of BAS glass powder and fine monoclinic celsian seeds. The fibers improve the mechanical strength and fracture toughness and with the matrix provide superior dielectric properties.

Bansal, Narottam P.↗
NASA NTRS1997

Chemical Vapor Deposited SiC (SCS-0) Fiber-Reinforced Strontium Aluminosilicate Glass-Ceramic Composites

Unidirectional SrO Al2O3 2SiO2 glass-ceramic matrix composites reinforced with uncoated Chemical Vapor Deposited (CVD) SiC (SCS-0) fibers have been fabricated by hot-pressing under appropriate conditions using the glass-ceramic approach. Almost fully dense composites having a fiber volume fraction of 0.24 have been obtained. Monoclinic celsian, SrAl2Si2O8, was the only crystalline phase observed in the matrix by x-ray diffraction. No chemical reaction was observed between the fiber and the matrix after high temperature processing. In three-point flexure, the composite exhibited a first matrix cracking stress of approx. 231 +/- 20 MPa and an ultimate strength of 265 +/- 17 MPa. Examination of fracture surfaces revealed limited short length fiber pull-out. From fiber push-out, the fiber/matrix interfacial debonding and frictional strengths were evaluated to be approx. 17.5 +/- 2.7 MPa and 11.3 +/- 1.6 MPa, respectively. Some fibers were strongly bonded to the matrix and could not be pushed out. The micromechanical models were not useful in predicting values of the first matrix cracking stress as well as the ultimate strength of the composites.

Bansal, Narottam P.↗
NASA NTRS1986

Making Highly Pure Glass Rods

Proposed quasi-containerless method for making glass rods or fibers minimizes contact between processing equipment and product. Method allows greater range of product sizes and shapes than achieved in experiments on containerless processing. Molten zone established in polycrystalline rod. Furnace sections separated, and glass rod solidifies between them. Clamp supports solid glass as it grows in length. Pulling clamp rapidly away from melt draws glass fiber. Fiber diameter controlled by adjustment of pulling rate.

Naumann, R. J.↗