Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fuel performance simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Performance Analysis of Magnetohydrodynamic Drag Modulation for Actively Controlled Aerocapture at Neptune

While the Ice Giants are a top priority for flagship missions in the NASA’s near-term future, current technologies limit the scientific payload and mission timeline for future Uranian and Neptunian missions due to the need for fuel for orbit insertion maneuvers. Thus, to maximize the scientific potential of future missions, atmospheric aerocapture has been heavily researched. While atmospheric aerocapture simulations have proven enabling for capturing around Neptune, its deep atmospheric pass requires an aeroshell with robust thermal protection systems (TPS). Magnetohydrodynamically-controlled aerocapture serves as a potential solution to the limitations of both fully propulsive orbit insertion and aerodynamically controlled aerocapture. Through NASA Langley’s high-fidelity flight dynamics simulation, the Program to Optimize Simulated Trajectories II, both the aerodynamic-only and magnetohydrodynamic aerocapture methods were simulated and compared for identical missions to Neptune. After applying an optimized numerical predictor-corrector guidance algorithm for both methods, the results showed that magnetohydrodynamics has not only the control authority to successfully capture around Neptune, but also the unique advantage of a shallower atmospheric pass, decreasing the maximum heat load and the required TPS mass.

Danny N. Nguyen↗
NASA NTRS1975

Nonreactive mixing study of a scramjet swept-strut fuel injector

The results are presented of a cold-mixing investigation performed to supply combustor design information and to determine optimum normal fuel-injector configurations for a general scramjet swept-strut fuel injector. The experimental investigation was made with two swept struts in a closed duct at a Mach number of 4.4 and a nominal ratio of jet mass flow to air mass flow of 0.0295, with helium used to simulate hydrogen fuel. Four injector patterns were evaluated; they represented the range of hole spacing and the ratio of jet dynamic pressure to free-stream dynamic pressure. Helium concentration, pitot pressure, and static pressure in the downstream mixing region were measured to generate the contour plots needed to define the mixing-region flow field and the mixing parameters. Experimental results show that the fuel penetration from the struts was less than the predicted values based on flat-plate data; but the mixing rate was faster and produced a mixing length less than one-half that predicted.

Mcclinton, C. R.↗
NASA NTRS1984

Calculation of a hollow-cone liquid spray in a uniform air stream

Fluid dynamic computer codes for the simulation of flows in gas turbine engine combustion systems are being developed. NASA is currently sponsoring a two-phase program for the evaluation of the performance of current codes, taking into account also an improvement of accuracy, if needed. The present investigation forms a part of this program. The numerical technique used includes a Lagrangian spray model for liquid fuels. The spray model, in conjunction with the turbulence model, determines the distribution of fuel in the burning zone of the combustor. The numerical technique was applied to a hollow-cone pressure atomizer spraying water into a coflowing confined airstream.

Sturgess, G. J.↗
NASA NTRS2000

Towards Flange-to-Flange Turbopump Simulations for Liquid Rocket Engines

The primary objective of this research is to support the design of liquid rocket systems for the Advanced Space Transportation System. Since the space launch systems in the near future are likely to rely on liquid rocket engines, increasing the efficiency and reliability of the engine components is an important task. One of the major problems in the liquid rocket engine is to understand fluid dynamics of fuel and oxidizer flows from the fuel tank to plume. Understanding the flow through the entire turbopump geometry through numerical simulation will be of significant value toward design. This will help to improve safety of future space missions. One of the milestones of this effort is to develop, apply and demonstrate the capability and accuracy of 3D CFD methods as efficient design analysis tools on high performance computer platforms. The development of the MPI and MLP versions of the INS3D code is currently underway. The serial version of INS3D code is a multidimensional incompressible Navier-Stokes solver based on overset grid technology. INS3D-MPI is based on the explicit massage-passing interface across processors and is primarily suited for distributed memory systems. INS3D-MLP is based on multi-level parallel method and is suitable for distributed-shared memory systems. For the entire turbopump simulations, moving boundary capability and an efficient time-accurate integration methods are build in the flow solver. To handle the geometric complexity and moving boundary problems, overset grid scheme is incorporated with the solver that new connectivity data will be obtained at each time step. The Chimera overlapped grid scheme allows subdomains move relative to each other, and provides a great flexibility when the boundary movement creates large displacements. The performance of the two time integration schemes for time-accurate computations is investigated. For an unsteady flow which requires small physical time step, the pressure projection method was found to be computationally efficient since it does not require any subiterations procedure. It was observed that the artificial compressibility method requires a fast convergence scheme at each physical time step in order to satisfy incompressibility condition. This was obtained by using a GMRES-ILU(0) solver in our computations. When a line-relaxation scheme was used, the time accuracy was degraded and time-accurate computations became very expensive. The current geometry for the LOX boost turbopump has various rotating and stationary components, such as inducer, stators, kicker, hydrolic turbine, where the flow is extremely unsteady. Figure 1 shows the geometry and computed surface pressure of the inducer. The inducer and the hydrolic turbine rotate in different rotational speed.

Kiris, Cetin↗
NASA NTRS2003

Coherent Anti-Stokes Raman Scattering (CARS) as a Probe for Supersonic Hydrogen-Fuel/Air Mixing

The dual-pump coherent anti-Stokes Raman spectroscopy (CARS) method was used to measure temperature and the absolute mole fractions of N2, O2 and H2 in a supersonic non-reacting fuel-air mixing experiment. Experiments were conducted in NASA Langley Research Center s Direct Connect Supersonic Combustion Test Facility. Under normal operation of this facility, hydrogen and air burn to increase the enthalpy of the test gas and O2 is added to simulate air. This gas is expanded through a Mach 2 nozzle and into a combustor model where fuel is then injected, mixes and burns. In the present experiment the O2 of the test gas is replaced by N2. The lack of oxidizer inhibited combustion of the injected H2 fuel jet allowing the fuel/air mixing process to be studied. CARS measurements were performed 427 mm downstream of the nozzle exit and 260 mm downstream of the fuel injector. Maps were obtained of the mean temperature, as well as the N2, O2 and H2 mean mole fraction fields. A map of mean H2O vapor mole fraction was also inferred from these measurements. Correlations between different measured parameters and their fluctuations are presented. The CARS measurements are compared with a preliminary computational prediction of the flow.

Danehy, P. M.↗
NASA NTRS1947

Simulated Altitude Performance of Combustors for the 24C Jet Engine: 24C-4 Combustor - 2

The performance of a 24C-4 combustor was investigated with three different combustor baskets and five modifications of these baskets at conditions simulating static (zero-ram) operation of the 24C jet engine over ranges of altitude and engine speed to determine and improve the altitude operational limits of the 24C combustor. Information was also obtained regarding combustion characteristics, the fuel-flow characteristics of the fuel manifolds, and the combustor total-pressure drop. NACA modifications, which consisted of blocking rows of holes on the baskets, increased the minimum point on the altitude-operational-limit curve, which occurs at low engine speeds, for a narrow-upstream-end basket by 8000 feet (from 23, 000 to 31,000 ft_ and for a wide-upstream-end basket by 21,000 feet (from 12, 000 to 34,000 ft). These improvements were approximately maintained over the entire range of engine speeds investigated.

Bernardo, Everett↗
NASA NTRS2015

Pathways Intern Report

During my time at NASA, I worked with the Granular Mechanics and Regolith Organization (GMRO), better known as Swamp Works. The goal of the lab is to find ways to utilize resources found after the astronaut or robot has landed on another planet or asteroid. This concept is known as in-situ resource utilization and it is critical to long term missions such as those to Mars. During my time here I worked on the Asteroid and Lava Tube Free Flyer project (ALTFF). A lava tube, such as the one shown in figure 1, is a long tear drop shaped cavern that is produced when molten lava tunnels through the surrounding rock creating large unground pathways. Before mining for resources on Mars or on asteroids, a sampling mission must be done to scout out useful resource deposits. ALTFF's goal is to provide a low cost, autonomous scout robot that can sample the surface and return to the mother ship or lander for further processing of the samples. The vehicle will be looking for water ice in the regolith that can be processed into either potable water, hydrogen and oxygen fuel, or a binder material for 3D printing. By using a low cost craft to sample, there is much less risk to the more expensive mother ship or lander. While my main task was the construction of a simulation environment to test control code in and the construction of the asteroid free flyer prototype, there were other tasks that I performed relating to the ALTFF project.

Pathways↗
NASA NTRSDate not supplied

Validation of CFD Model Prediction of Flow Boiling Regime Transitions during LN2 Line Chilldown

Propellant storage and transfer during future long-duration missions will involve fuel depot operations in which a donor depot tank is used to fill a receiver spacecraft tank with a cryogenic propellant. Prior to the on-Orbit filling operation both the receiver tank and the transfer line must be cooled. The line chilldown process involves transition between boiling regimes in microgravity that will be quite different from their 1g ground-based counterparts. Since the cryogenic propellant itself will be used to perform the chilldown process, the time constants to cool the wall and the amount of fuel that will be used become important design considerations. In this light, the focus of the present work is to understand the flow boiling characteristics of a cryogenic fluid, namely, liquid nitrogen, during the chill-down of a transfer line using CFD modelling and simulations. The cryogenic chill-down process involves different flow boiling regimes: film boiling, transition boiling and nucleate boiling. The prediction of transition between these regimes in a CFD framework is new and challenging. The present work addresses this challenge by employing a volume-of-fluid (VOF) based methodology with Lee phase change model to predict the film boiling regime of the chill-down process in ANSYS Fluent®. The transition and nucleate boiling regimes are predicted by incorporating a sub-grid model developed by Craft Tech that accounts for bubble nucleation, growth, shedding frequency, and departure diameter. The sub-grid model is implemented into Fluent via a user-defined function for wall-fluid heat flux calculations. The sub-grid model is similar in formulation to the well-known Rensselaer Polytechnic Institute (RPI) boiling model. The model constants are tested for different operating conditions and designated values are reported. The CFD model is validated against published experimental data for liquid nitrogen chill-down of a heated stainless-steel pipe in 1g. Predicted results showing good agreement of wall temperature, rewetting temperature, and transition between film and nucleate boiling with the experimental measurements are presented and discussed.

Boiling regimes↗
NASA NTRSDate not supplied

Predictions of Line Chilldown Boiling Regime Transitions by a Coupled CFD-Sub-Grid Boiling Model Validated against 1G LN2 Experiments

Propellant storage and transfer during future long-duration missions will involve fuel depot operations in which a donor depot tank is used to fill a receiver spacecraft tank with a cryogenic propellant. Prior to the on-Orbit filling operation both the receiver tank and the transfer line must be cooled. The line chilldown process involves transition between boiling regimes in microgravity that will be quite different from their 1g ground-based counterparts. Since the cryogenic propellant itself will be used to perform the chilldown process, the time constants to cool the wall and the amount of fuel that will be used become important design considerations. In this light, the focus of the present work is to capture the flow boiling characteristics of a cryogenic fluid, namely, liquid nitrogen, during the chill-down of a transfer line using CFD modelling and simulations. The cryogenic chill-down process involves different flow boiling regimes: film boiling, transition boiling and nucleate boiling. The prediction of transition between these regimes in a CFD framework is new and challenging. The present work addresses this challenge by employing a volume-of-fluid (VOF) based methodology with Lee phase change model to predict the film boiling regime of the chill-down process in ANSYS Fluent®. The transition and nucleate boiling regimes are predicted by incorporating a sub-grid model that accounts for bubble nucleation, growth, shedding frequency, and departure diameter. The sub-grid model is implemented into Fluent via a user-defined function for wall-fluid heat flux calculations. The sub-grid model is similar in formulation to the well-known Rensselaer Polytechnic Institute (RPI) boiling model. The CFD model is validated against published experimental data for liquid nitrogen chill-down of a heated stainless-steel pipe in 1g. Predicted results shows good agreement of wall temperature, rewetting temperature, and transition between film and nucleate boiling with the experimental measurements for several different LN2 flowrates in the vertical orientation. The strengths and weaknesses of this modeling approach are presented and discussed.

Cryogenic Fluid Management↗
NASA NTRS1989

Hydrocarbon-fueled scramjet combustor component development tests

Technology is being developed for a hydrocarbon-fueled engine operating as a scramjet over the flight Mach number range from 5.6 to 7. A series of connected-pipe tests were performed to define scramjet combustor design criteria applicable to the United Technologies Research Center (UTRC) engine concept which comprises a pair of modular axisymmetric combustor underslung on a supersonic/hypersonic missile. The development of key pilot and fuel injector components of the combustor is pursued in a variable-geometry two-dimensional test section over a range of combustor entrance conditions simulating the intended flight regime. The applicability of the two-dimensional test results to the axisymmetric engine is ensured by maintaining a proper simulation of combustor entrance conditions and preserving the actual length scale in the two-dimensional test configuration. An air-breathing pilot was developed and tested to evaluate flame stabilization and flame propagation characteristics. A pilot configuration was developed that operated stably, with minimal flow spillage, at exhaust stagnation temperatures as high as 4500 R with ethylene fuel. It was demonstrated that the pilot promotes efficient combustion of either gaseous ethylene or preheated liquid Jet-A (JP-5) when they are injected into the supersonic mainstream flow as primary fuels. For the tests with Jet-A fuel, the fuel was heated in an array of internal cooling passages within the pilot walls to a thermodynamic condition such that it would flash-vaporize upon injection into the mainstream flow. The idea of using the air-breathing pilot and distributed primary and secondary fuel injectors to achieve efficient supersonic combustion over a wide range of equivalence ratios was also experimentally demonstrated during the program. During staged fuel injection tests with gaseous ethylene fuel, high secondary fuel combustion efficiencies were achieved and smooth transitions from fully supersonic to dual mode (supersonic/subsonic) operation were demonstrated at high overall equivalence ratios.

Kay, Ira W.↗
NASA NTRS2015

Development of a Premixed Combustion Capability for Scramjet Combustion Experiments

Hypersonic air-breathing engines rely on scramjet combustion processes, which involve high speed, compressible, and highly turbulent flows. The combustion environment and the turbulent flames at the heart of these engines are difficult to simulate and study in the laboratory under well controlled conditions. Typically, wind-tunnel testing is performed that more closely approximates engine testing rather than a careful investigation of the underlying physics that drives the combustion process. The experiments described in this paper, along with companion data sets being developed separately, aim to isolate the chemical kinetic effects from the fuel-air mixing process in a dual-mode scramjet combustion environment. A unique fuel injection approach is taken that produces a nearly uniform fuel-air mixture at the entrance to the combustor. This approach relies on the precombustion shock train upstream of the dual-mode scramjet combustor. A stable ethylene flame anchored on a cavity flameholder with a uniformly mixed combustor inflow has been achieved in these experiments allowing numerous companion studies involving coherent anti-Stokes Raman scattering (CARS), particle image velocimetry (PIV), and planar laser induced fluorescence (PLIF) to be performed.

Rockwell, Robert D.↗
NASA NTRSDate not supplied

Feasibility and Performance Analysis of Magnetohydrodynamics Control for Aerocapture at Neptune

NASA’s most recent Decadal Survey posed a mission to one of the Ice Giants as the top priorityfor flagship missionsin the organization’s future. However, current technologieslimit the amount of scientific payload available for future Uranian and Neptunian missions due to the need for fuel for orbit insertion maneuvers. Thus, to maximize the scientific potential of futuremissions, atmospheric aerocapture has been heavily researched. While atmospheric aerocapture simulations have proven enabling for capturing around Neptune, its deep atmospheric pass requiresan aeroshell with thermal protection systems(TPS).Magnetohydrodynamically-controlled aerocapture serves as a potential solution to both fully-propulsive orbit insertion and atmospheric aerocapture. Through NASA Langley’s high-fidelity flight dynamics simulation, the Program to Optimize Simulated Trajectories II, both the atmospheric and magnetohydrodynamic aerocapture methods were simulated and compared for identical missions to Neptune. After applying a guidance algorithm for both methods, the results showed that magnetohydrodynamics has not only the control authority to successfully capture around Neptune, but also the unique advantage of a shallower atmospheric pass which decreases the maximum heat load and the required TPS mass.

Danny N Nguyen↗
NASA NTRS2000

Electric Plasma Arc-Lamp Combustor Liner Durability Test System Developed

Silicon carbide matrix composites are candidate materials for high-temperature combustor liners. Because through-the-thickness thermal gradients are the primary cause of stress on combustor liners, a unique test facility was developed at the NASA Glenn Research Center at Lewis Field to simulate in-service pure thermal stress distributions in fiber reinforced silicon carbide cylinders. It was developed initially under Phase II of the High- Speed Research Program. This test stand can accommodate 8-in.-long test cylinders that have outer diameters of 4 in. and a wall thickness of about 0.08 to 0.12 in. One cylinder at a time is loaded vertically into the test stand. Water-cooled plates enclose the open ends of the cylinder and provide cooling. Load plates on the exterior side of the water-cooled plates provide support and compression loads. To evaluate a combustor liner material s potential performance, researchers induce thermal gradients with an axisymmetric, direct-current, electric arc within the cylinder while refrigerated air at a rate of 1.5 lb/sec impinges on the outside surface of the cylinder. The achievable through-the-thickness thermal gradient is predicted to be in excess of 200 C. The 8-in. long, 0.5-in.-diameter plasma arc emits full spectrum visible light; radiant intensity exceeds 300 Watts per square centimeters to produce temperatures in excess of 1500 C on materials with emissivity near unity. Because the system does not rely upon the combustion of fuels to achieve the related thermal conditions, ancillary environmental reactions with the sample are eliminated. The system incorporates a standard mechanical test frame, which can impose constant as well cyclical axial stresses up to 2200 lb upon the test piece. Silicon-carbide-fiber reinforced silicon carbide matrix composite cylinders were instrumented with thin-film thermocouples to obtain through-the-thickness thermal flux measurements. Inside wall temperatures reached 1200 C with only 250 A of current. One of the special features of this configuration is the creation of hoop stress states within the cylinder, which up this point have not been obtainable in planar coupon tests. This facility will allow various operational modes, including accelerated tests of thermal transients simulating the effects of repeated engine ignition as well as prescribed thermal and mechanical histories to simulate various duty cycle profiles. Tests can now be performed on thermal-barrier-coated metallic liners and ceramic composite liners that require a combination of high heat flux and controlled mechanical stresses.

Goldsby, Jon C.↗
NASA NTRS1974

Operations analysis (study 2.1). Program SEPSIM (solar electric propulsion stage simulation)

Program SEPSIM is a FORTRAN program which performs deployment, servicing, and retrieval missions to synchronous equatorial orbit using a space tug with a continuous low thrust upper stage known as a solar electric propulsion stage (SEPS). The SEPS ferries payloads back and forth between an intermediate orbit and synchronous orbit, and performs the necessary servicing maneuvers in synchronous orbit. The tug carries payloads between the orbiter and the intermediate orbit, deploys fully fueled SEPS vehicles, and retrieves exhausted SEPS vehicles when, and if, required. The program is presently contained in subroutine form in the Logistical On-orbit VEhicle Servicing (LOVES) Program, but can also be run independently with the addition of a simple driver program.

Lang, T. J.↗
NASA NTRS1978

Airframe-integrated propulsion system for hypersonic cruise vehicles

The paper describes a new hydrogen-burning airframe-integrated scramjet concept which offers good potential for efficient hypersonic cruise vehicles. The characteristics of the engine which assure good performance are extensive engine-airframe integration, fixed geometry, low cooling, and control of heat release in the supersonic combustor by mixed modes of fuel injection from the combustor entrance. The present paper describes the concept and presents results from inlet tests, direct-connect combustor tests, and tests of two subscale boiler-plate research engines currently underway under conditions which simulate flight at Mach 4 and 7. It is concluded that this engine concept has the potential for high thrust and efficiency, low drag and weight, low cooling requirement, and application to a wide range of vehicle sizes.

Jones, R. A.↗
NASA NTRS1921

Performance of a Liberty 12 airplane engine

In cooperation with the Engineering Division of the Air Service of the United States Army, a Liberty-12 engine has been tested at the Bureau of Standards. The program of tests was planned to yield that information considered most important in determining the value of the engine for aviation. Full power runs were made at the ground, at 25,000 feet, and at several intermediate altitudes. To determine the mechanical efficiency of the engine, friction horsepower was measured at the ground and at 15,000 feet. As a basis for predicting engine performance with a propeller, a series of tests was made in which the dynamometer load and engine throttle were adjusted at each speed to simulate the engine load which would be imposed at that speed by a propeller operating under normal full load at 1,700 r.p.m. Among the quantities calculated from the test measurements are: brake horsepower; break mean effective pressure; fuel consumption; mixture ratio; mechanical, thermal, and volumetric efficiency; and the percentage of the heat in the fuel appearing in the jacket water and in the exhaust. Jacket water temperature, oil temperature, manifold pressure, etc., are recorded to show the conditions under which the test was made.

Sparrow, S W↗
NASA NTRS2000

Development Progress in Phase 1 Fission Propulsion Systems

Phase 1 fission propulsion systems are those fission propulsion systems that are highly testable and require no development of nuclear fuels or materials. The systems can be developed without new or significantly modified facilities, have adequate performance for numerous missions of interest, and demonstrate technologies and programmatics that are traceable to Phase 2 and Phase 3 systems. Phase 1 fission propulsion systems focus on safety, cost and schedule. Phase 1 flight units can be tested at full thrust using resistance heaters to simulate heat from fission. The development and use of Phase 1 systems will help enable Phase 2 or Phase 3 fission propulsion systems capable of giving rapid, affordable access to any point in the solar system. A Phase 1 fission propulsion system under development at the Marshall Space Flight Center (MSFC) in collaboration with individuals from Department of Energy Laboratories and industry is the Safe Affordable Fission Engine (SAFE). The propellant energy source of a 30 kW SAFE unit (SAFE-30) is being fabricated, and will begin testing at MSFC in FY00. The conceptual design of a 300 kW SAFE unit (SAFE-300)is nearing completion. Experiments have been performed on both SAFE-30 and SAFE-300 components. Module tests have confirmed the performance potential of the SAFE series of propulsion systems. This paper will report on the development status of the Phase 1 SAFE fission propulsion system.

Houts, Michael G.↗
NASA NTRS2000

Mixing, Noise and Thrust Benefits Using Corrugated Designs

These projects are directed toward the analysis of several concepts for nozzle and inlet performance improvement and noise reduction from jet exhausts. Currently. The FM&AL also initiates new joint research between the HU/FM&AL, the Hyper-X Program Team at the LaRC, and the Central Institute of Aviation Motors (CIAM), Moscow, Russia in the field of optimization of fuel injection and mixing in air-breathing propulsion systems. The main results of theoretical, numerical simulation and experimental tests obtained in the previous research are in the papers and patents. The goals of the 14U/FM&AL programs are twofold: 1) to improve the working efficiency of the HU/FM&AL team in generating new innovative ideas and in conducting research in the field of fluid dynamics and acoustics, basically for improvement of supersonic and subsonic aircraft engines, and 2) to attract promising minority students to this research and training and, in cooperation with other HU departments, to teach them basic knowledge in Aerodynamics, Gas Dynamics, and Theoretical and Experimental Methods in Aeroacoustics and Computational Fluid Dynamics (CFD). The research at the HU/FM&AL supports reduction schemes associated with the emission of en 'ne pollutants for commercial aircraft and concepts for reduction of 91 observables for military aircraft. These research endeavors relate to the goals of the NASA Strategic Enterprise in Aeronautics concerning the development of environmentally acceptable aircraft. It is in this precise area, where the US aircraft industry, academia, and Government are in great need of trained professionals and which is a high priority goal of the Minority University Research and Education (MLTREP) Program, that the HU/FM&AL can make its most important contribution.

Morgan, Morris H., III↗