SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
This presentation is titled ORNL Nuclear Data Evaluation Contribution to NCSP (ND-2). This lecture includes resonance evaluations, SAMMY fitting results, and resonance evaluation features. The presentation finishes with evaluations in alkaline earth-metals and halogens.
To allow for on-site Potassium Dihydrogen Phosphate (KDP) crystal finishing capabilities, Lawrence Livermore National Laboratory (LLNL) acquired the Moore 3 diamond turning machine. Equipment such as the Moore 3 is required by LLNL to have adequate seismic bracing before permanent installation to reduce the risk of personnel injury or machine damage during an earthquake. The purpose of this project was to design a bracket that can withstand seismic forces induced by the machine without hindering function. To develop a solution, background research—including stakeholder identification, stakeholder interviews, and a literature survey—was conducted. Based on LLNL site and stakeholder requirements, several approaches were developed for bracing the Moore 3. Ideations were evaluated based on a weighted decision matrix and a final design strategy was selected. This design was an L-shaped weldment that featured provisions for four HILTI concrete anchors, three triangular gussets, and a steel construction.
The goal of the Scalable Thin Light-Emitting Diode (LED) Light Sheet Platform project is to derisk the manufacturing scalability for a high chip count heterogeneous smart lighting platform, with the potential to enable significant energy savings through dynamic directional light control and custom. Specifically, the project derisks the scalability of a disruptive new computer controlled microassembly fabrication process SRI International is developing, to address fundamental cost barriers to mass production of high chip count systems. This is key for enabling mass adoption and thus maximum societal energy savings impact. The LED light sheet technology is a smart illumination platform that can be applied to lighting, signage, and display. It has features and a form factor similar to bendable or conformal OLED light sheets but uses more efficient LEDs with a remote phosphor layer that is very close to the LED to deliver a luminous efficacy that exceeds 125 lumen/Watt and enable > 50% Lighting Application Efficiency (LAE) energy savings. During Budget Period 1 (BP1), all of the BP1 milestones were successfully completed: (M2.0.1) Design demonstrator details that will meet the final project goals, (M6.1.1) Show lighting output model can predict illuminance, spatial, spectral distribution for specific light-sheet designs and use case, (M3.2.1) Automated loading supports 200 chip arrays, and (M3.3.1) Finish first interconnect process run for 200 chip array. The BP1 Go/No-Go Decision Point (G/NG 1) 200 chip demonstrator sample was in the process of final assembly and test at the end of BP1 on December 31, 2023. The objective was successfully achieved on January 16, 2024, when a wired 200-chip sample underwent confirmation testing that demonstrated a 93.75% first pass electrical yield that successfully exceeded the 75% first-pass electrical yield BP1 G/NG requirement. In addition, all 93.75% of the sample devices lit up, further demonstrating the ability to assemble and transfer small LED chips without damaging their functionality.
Ultra-black coatings have served various roles in space instrumentation and hardware. The Ebonol C coating has been used for various missions requiring low reflectivity on aluminum substrates that are electrically conducting. This coating is produced through the formation of a cupric oxide structure on an intermediate layer of copper applied to the aluminum. For many years, this commercial formulation has been used ubiquitously for space instruments. The coating relies upon details of the copper base layer that have been trade secret at various finishing companies, and the availability of the Ebonol C formulated chemistry from the chemical supplier. In recent years, this product has been discontinued at various times, leaving vendors to either rely on expired stock or to formulate their own equivalents. Here, we detail the processing methods, chemistries, and resultant coating structures that produce reflectance performance equivalent to baseline historical reflectance data. This process detail will ensure equivalent performance for such coatings for future missions and link the performance to past and currently deployed instruments.
This is the final scientific / technical report for Front End Engineering Design (FEED) study “Retrofittable Advanced Combined Cycle Integration for Flexible Decarbonized Generation” funded by the US Department of Energy (DOE), Office of Fossil Energy and Carbon Management (FECM), Carbon Capture R&D Program under award DE-FE0032131. The prime recipient is General Electric Company working through its Gas Power division (GEGP) with subrecipients Southern Company and Linde Engineering plus subcontractor Kiewit. Southern Company’s Plant Barry, a 2x1 7F.04 CCGT, is the host site. GEGP led the overall integration of the carbon capture system (CCS) with the existing natural gas combined cycle (NGCC) facility. Linde provided the detailed process engineering and equipment costing for the carbon capture island. Kiewit focused on plant layout, constructability, and installation. With the FEED study finished, the engineering is approximately 50% complete towards the detailed design package needed to proceed to procure, install, build, commission, and operate the integrated NGCC+CCS facility. This FEED study focuses on retrofitting a 95% CO 2 capture system with attention on plant integration. The study was particularly challenging due to unique and substantial cost impacts related to global sourcing challenges associated with COVID. Additional incentives, regulatory support, and dispatch certainty are needed to move forward with implementing CCS at this or other sites in the US. This FEED study highlights the value of integrating NGCC+CCS and is a template for future CCS retrofit studies.
Diversion of nuclear materialsfrom legitimate commercial processes for use by nefarious actors is a frightening and surreptitious problem. Smuggled nuclear material can be used to manufacture a simple radiological dispersion device (RDD) and potentially incorporated into the development of a nuclear weapon. With some frequency, smuggled nuclear material is interdicted in foreign countries as actors cross border checkpoints. Nuclear material interdicted in this way can be analyzed using a variety of tools. Plutonium-239 is commonly used as the fissile material in nuclear weapon production as an alternative to uranium-235. Plutonium in a production, refining, or finishing facility will exist in many forms including oxide precursors (PuF4, PuF3, Pu oxalate, etc.), oxide, and metal. The ability to identify plutonium in each of these forms and determine properties, characteristics, or history of these materials is crucial for determining if the processes occurring in a nuclear facility are legitimate or not. This presentation will focus on the development and application ofspectroscopic tools developed at SRNL using doubled-walled cells (DWC) to characterize Pu-bearing compounds. Advances in the use of vibrational spectroscopy techniques (Raman and IR), UV-VIS-SWIR diffuse reflectance spectroscopy, gamma emission spectroscopy, luminescence spectroscopy, laser-induced breakdown spectroscopy in conjunction with XRD and SEM in the characterization of Pu-bearing compounds will be presented with emphasis in material processing history.
This report focuses on accomplishments and activities completed. Along with leadership/professional developments activities recently completed. It finishes with a look at issues and challenges and upcoming activities.
Thermal energy storage is anticipated to play an important role in developing the power grid of the future - a power grid that meets increasing demands of users, is resistant to disruptions, but also allows for greater penetration of renewable resources. Specifically, thermal energy storage materials can be integrated into HVAC systems and building envelopes, where they can be used to shift power demands for building climate control from periods of peak demand to periods of low demand. Phase change materials (PCMs) are compelling as low-cost, high energy density thermal energy storage materials for building thermal management. However, there is a lack of high performance low-cost PCMs within the specific temperature ranges which would most effectively allow for power load shifting. Inorganic salt hydrates represent a promising class of PCMs, but their inherent limitations cause them to be currently unavailable for reliable building applications. The overarching goals of this research effort are to: 1) Discover low-cost, high volumetric density salt hydrate eutectic PCMs to store low-quality heat (10 to 40 °C); 2) Introduce a high thermal conductivity matrix to reduce the time constant for energy storage to ~0.1 to 1 hr, incorporate nucleation catalysts to decrease undercooling, and utilize microencapsulation and shape stabilization approaches, minimizing moisture loss/gain, mitigating phase separation, and maintaining stable melting behavior over the lifetime of the compounds; 3) Evaluate the impact these systems have on peak load shifting, and the potential for overall energy savings under different climatic scenarios and building configurations. These goals will be achieved by an integrated research program consisting of six cohesive research subtasks: 1) Materials discovery of eutectic salt hydrate PCMs by using computationally predicted thermodynamic equilibria, coupled with high-throughput experimental validation, 2) Rapid experimental screening of nucleation catalysts identified through robust computational databases, 3) Embedding salt hydrate PCM into a low cost and scalable high conductivity matrix, 4) Microencapsulation of salt hydrate microspheres using hybrid inorganic-polymer microencapsulation approach, 5) Shape stabilization by thermoreversible salt hydrate salogels, and 6) Analysis of end-use using thermal simulations, and characterization of mock-up energy storage finished components.
Objective: To develop an easy-to-use software application to predict and mitigate radiation effects in research environment, space instruments, nuclear plants and medical facilities and help nonproliferation and national security efforts. Tech-X will develop standalone software libraries and command-line tools for ( 1) translating CAD into tessellated surfaces and tetrahedral meshes in GDML (for Geant4 and MARS 15), ROOT (for MARS 15) and HDF5 (for compact representation and for the visualization) formats, (2) healing CAD geometries to make them suitable for Monte Carlo simulations; (3) creating uniform and variable Cartesian and cylindrical meshes for detailed scoring; and ( 4) efficient Monte Carlo navigation in CAD geometries. JLAB will finish automation of simulations of residual dose in CAD geometries and integrate Tech-X software into Geant4 and MARS15. Finally, Tech-X will develop a Graphical User Interface to set up and heal CAD geometries, create input files, run and visualize simulations for residual dose. This application will run on local desktops, local and remote clusters and supercomputers and will be made available through public clouds, such as Amazon Web Services.
FY23 Sustainment, performed from 1 March through 30 September, completed with Cumulative Costs at 69% and combined Costs plus Commitments at 87%. Nineteen projects were completed in FY23. Eleven projects continue to close out purchasing activities or will roll over into FY24 projects. Two projects have been placed on hold and will be reevaluated for potential future consideration. Diagnostics projects issued all planned FY23 purchases and finished FY23 with 78% cumulative costs and combined costs and commitments at 102%. FY24 Sustainment Project identification, definition and prioritization was completed. Once the budget is finalized, project selection will quickly be set and projects kicked off.
The Spent Fuel Waste Disposition (SFWD) program under the U.S. Department of Energy (DOE) is planning a seismic shake table test of full-scale dry storage systems of spent nuclear fuel (SNF) to close the gap related to the seismic loads on the fuel assemblies in dry storage systems. This test will allow for quantifying the strains and accelerations on surrogate fuel assembly during representative earthquakes. A concrete layer will be installed on the shake table before the test to simulate conditions representative of an ISFSI pad. In the shake table tests with the vertical cask, the cask will be free-standing because this is representative of all, except two, ISFSIs in the U.S. with vertical dry storage casks. The static and dynamic friction coefficients between the steel bottom of the cask and the concrete layer on the shake table are important parameters that will affect cask behavior during the test. These parameters must be known for the pre- and post-test modelling, data analysis, and model validation. The friction experiment was performed at the Engineering Department of the University of New Mexico (UNM) to determine the friction coefficients between a steel plate with the same finish as the bottom of the vertical cask manufactured for the test and different concrete surfaces. In this experiment the steel plate was fixed and the concrete sample was pulled over the plate with a constant displacement rate using an MTS machine. This allowed for collecting continuous horizontal force data over the length of the steel plate. Four displacement rates and three vertical loads were used. The tests were performed with four concrete blocks with different degrees of the surface roughness - light sandblast, light to medium sandblast, medium bush hammer, and heavy sandblast. The total number of tests was 48. The data were used to calculate static and dynamic friction coefficients.
Introduction – What are Magnetic Materials? Magnetic materials are crystalline solids which below a certain temperature, known as the ordering temperature, display spontaneous order in their magnetic moments. Results • Enhanced thermal stability and saturation magnetization with Y substitution in Ce2Fe14B based permanent magnets • Discovered a new ferromagnetic phase transition at TC = 62.9 K in (Dy1/3Mo2/3)2AlC and validated the two previously reported low temperature magnetic phases Characterization of Magnetic Materials Raw high purity materials are melted together to synthesize a crystalline sample using an arc melter at Savannah River National Laboratory (SRNL). Use high energy ball milling to form a hard/soft magnetic composite using Y substituted Ce2Fe14B. Finish structural characterization on γ- irradiated (RE1/3Mo2/3)2AlC (RE = Rare Earth) MAX samples. Unit Cell Lattice Points
A first field test of the inexpensive and ruggedized online holdup monitor under development at the US Department of Energy’s Oak Ridge National Laboratory (ORNL) was performed in September of 2023 with highly successful results. ORNL staff collaborated with personnel at the National Fuel Services (NFS) to place two battery-powered detector units at the facility, one on a fuel processing line and the other on a HEPA filter. Both units collected gamma-ray counts per second, temperature, humidity, and battery power data every 5 s seconds over the course of 19 days. Analyzed results from the measurements were discussed with NFS personnel after the units were removed. Vendor feedback on the units was overwhelmingly positive with an expressed desire to deploy finished units at the facility and an open invitation for testing future prototypes.
This report details the results for an optimization of the dimensions of the moderators in the preliminary design of the Spallation Neutron Source Second Target Station (STS). This study uses the optimization algorithms of Dakota and an unstructured mesh model for the moderators in MCNP. More details on the unstructured mesh model and the automated mesh generation can be found in [3]. Parallel to this effort, the same moderator geometries have been optimized using a constructive solid geometry (CSG) MCNP model. More details on this model and its results can be found in [4]. Three optimal designs are selected for each moderator: one that is optimized for maximum peak brightness, one for maximum time-integrated brightness, and one for a combination of peak and time-integrated brightness. The backbone of the optimization work flow is provided by Dakota. For each set of design parameters requested by Dakota, a new solid geometry is automatically built in Creo and SpaceClaim, and subsequently exported to Attila4MC to generate an unstructured mesh geometry for MCNP. After the MCNP calculation is finished, the objective function (e.g., brightness metric) is returned to Dakota. After the new design has been evaluated, a result-file is written, and Dakota proposes the next set of design parameters to be evaluated. The loop continues until a specified convergence criterion has been met. The design parameters of the cylindrical (upper) moderator include the hydrogen radius, the premoderator thickness (top, bottom, radial), the beryllium radius and the horizontal position of the moderator. The crucial design choice is the hydrogen radius. A radius of 62 mm is shown to provide the maximum time-integrated brightness. The maximum peak brightness occurs with a radius of 40 mm. A combined (middle) design, which balances peak and time-integrated brightnesses, is obtained with a hydrogen radius of 50 mm. The premoderator thicknesses and the beryllium radius are slightly larger in the design optimized for time-integrated brightness than in the design optimized for peak brightness. The sensitivity to these two parameters is relatively small close to the optimal configurations. The hydrogen vessel and vacuum vessel wall thicknesses are dependent on the radius of the liquid hydrogen due to structural integrity requirements. The increased wall thicknesses for larger vessels significantly penalize the time-integrated brightness, with the maximum obtainable value reduced by more than 10% relative to earlier studies which used fixed vessel wall thicknesses. The impact of the variable wall thicknesses is much less for the peak brightness and combined brightness designs. The design parameters of the tube (lower) moderator selected for the optimization are the tube length, the annular premoderator thickness, the beryllium radius and the horizontal position of the moderator. The tube length is the crucial parameter and is chosen large (210 mm) and small (125 mm) in the designs optimized for time-integrated and peak brightness respectively. A combined optimal design has a tube length of 170 mm. The premoderator thickness and the beryllium radius are chosen larger in the design optimized for time-integrated brightness.
This report documents the 100,000 hour, Class A ASME design material data for Alloy 709 based on the extensive Department of Energy, Office of Nuclear Energy, Advanced Reactor Technologies qualification test campaign. This report includes design tensile properties, creep rupture data, allowable stresses, isochronous stress-strain curves, buckling charts, and a few additional miscellaneous pieces of design data. Companion work at Oak Ridge National Laboratory and Argonne National Laboratory provide design cyclic data --- fatigue charts and creep-fatigue diagrams --- and an inelastic constitutive model. This work substantially completes the ASME data package for the Alloy 709 Code Case, though the design data will continue to updated as the final tests finish. This report also compares the design performance of Alloy 709 against that of 316H stainless steel to provide a reference for the improved high temperature strength of 709 compared to a reference material for sodium fast reactor construction.
The U-Gas gasification technology, marketed by Sungas, is a proven fluid bed gasification technology for biomass conversion. U-Gas has been tested on a wide variety of biomass feeds including wood and waste streams. The U-Gas Technology has successfully converted wood for more than 20 years in a gasification plant in Skive Denmark at the 150t/d size. GTI has also recently developed the Cool GTL process for converting biogas to high quality gasoline, jet, and diesel fuels. The technoeconomics and LCA for the combination of the two technologies results an integrated optimized process, which will be discussed. The Cool GTL process is still in development and the development should be complete by 2023. Cool GTL converts high CO2 content feeds to synthesis gas with a 2-2.4/1 H2/CO ratio suitable for fuels synthesis. The process is based on a novel, highly stabile CO2/steam reforming catalyst. The 2.0-2.4/1 H2/CO synthesis gas ratio is always achieved, independently of feed CO2 content, by adjusting the amount of water added according to the amount of CO2 in the feed. The reformer catalyst has been tested for 500 hours and shows no measurable deactivation. The product from the reformer then goes directly to a low temperature slurry bed Fischer Tropsch reactor with an integrated finishing hydroisomerization reactor which makes hydrocarbon liquids from the synthesis gas. With this configuration no wax is produced. The technoeconomics and carbon intensity for the integration of UGas and the Cool GTL processes will be compared to other biomass conversion approaches. The use of electrolysis to boost H2 in the feed and increase liquid production will also be analyzed as a potential process improvement with sensitivities to the cost of electricity and the use of renewable electricity.
This study, performed on behalf of Washington River Protection Solutions (WRPS), examines the potential for making cost savings for the Immobilized Low Active Waste (ILAW) containers over the mission life of the Waste Treatment and Immobilization Plant (WTP). it builds on earlier study assessments 24590-LAW-RPT-M-01-001 Rev 0 ILAW Product Container Specifications Optimization Study and DOE/ORP-2013-02 Rev 0 Decision Analysis of Low-Active Waste Container Finishing Handling System Alternatives. The WTP design and installed equipment has evolved over an extended period ~20 years. Consequently, some of the existing requirements relating the ILAW containers may no longer be applicable under current mission plans where the glass filled containers are placed into the Integrated Disposal Facility (IDF) rather than stacked in an engineered purpose-built ventilated store as originally envisioned. The study team reviewed available WTP project reference documents to establish the functions the container must perform and assign requirements against each of these functions. With the assumptions that some of the existing WTP contract restrictions would not necessarily apply to the subsequent facility operations contract the container requirements were reviewed to identify those which were ‘hard constraints‘, imposed by regulatory requirements. Initially each of these hard constraints were reviewed, evaluated and documented to see if they precluded the use of an alternate less expensive material of construction, carbon steel, to the existing 304 L stainless steel in the current container specification. That review did not generate any fatal flaws for a change in material of construction to carbon steel allowing the study team to examine the impacts of material cost savings, potential changes to the design and requirements and impacts on interfaces of the containers with the existing WTP process equipment from container receipt, transfers, glass filling, cooling and export. In addition, a change in container target fill level was evaluated and qualitative, and quantitative where feasible, impacts to the container fabrication process assessed. Lastly, additional follow on development or testing activities to support the use of carbon steel were assessed and a recommended path forward with a ROM cost and timescale developed.
This project successfully developed and demonstrated the synergistic thermo-microbial-electrochemical (T-MEC) process, converting food waste into sustainable biofuels while achieving self-sustaining wastewater treatment and hydrogen production. By integrating hydrothermal liquefaction (HTL) and microbial electrolysis cells (MECs), the project advanced waste-to-fuel technology and expanded the understanding of sustainable waste valorization. It established a scalable framework for achieving high carbon efficiency, effective pollutant removal, and energy recovery, showcasing the potential of combining biological, thermal, and electrochemical systems to optimize resource recovery and reduce environmental impacts. The project demonstrated the technical effectiveness of the T-MEC process, achieving over 50% improvement in carbon efficiency and reducing waste processing costs by more than 25% compared to anaerobic digestion (AD). The HTL pilot reactor processed food waste at 90 kg/h, producing up to 200 L/day of biocrude oil with high conversion efficiency. A critical desalting step in pretreatment prevented catalyst fouling, enabling efficient hydrotreating with 100% deoxygenation and denitrogenation and sulfur reduction to <15 ppm. This positioned the kerosene fraction as a strong candidate for sustainable aviation fuel (SAF). The MECs achieved rapid startup, 86.4% COD removal, and hydrogen production rates of 1.8 L H 2 /L cat /day, among the highest recorded for pilot-scale systems. The integrated process achieved 65% carbon efficiency to biocrude and 58% to finished fuels, outperforming AD's 41% and 33% efficiencies for biogas and natural gas vehicle fuels. System analysis highlighted economic potential, with minimum fuel selling prices (MFSP) decreasing from $\$$25/GGE at 5 tpd to $\$$10/GGE at 500 tpd due to economies of scale. Future work will focus on reducing MEC material and membrane costs, enhancing performance through higher current densities, and creating tailored operational strategies for diverse feedstocks. Optimization of the integrated system will improve scalability and feasibility, positioning the T-MEC process as a competitive solution for converting wet waste into sustainable fuels and clean water. Beyond its technical and economic achievements, the project offers significant public benefits. The T-MEC process provides a sustainable alternative to landfilling and incineration, reducing greenhouse gas emissions and conserving resources. Converting waste into SAF and renewable fuels supports decarbonization in the transportation sector, advancing energy independence and reducing reliance on fossil fuels. Additionally, the process minimizes environmental pollutants, transforming them into valuable products like hydrogen and fuels, contributing to a cleaner and more sustainable future.