Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fasteners”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

A survey of strength analysis methods for laminates with holes

The methods for predicting the strength of composite laminates with fastener holes are reviewed for the cases of unloaded as well as loaded holes. Three categories of methods are discussed: (1) the hole-boundary stress (HBS) methods which compare the peak stresses and the laminate strength; (2) the linear elastic fracture (LEFM) methods which assume cracks emanating from the hole and predict failure when the stress intensity factor for a crack equals the laminate fracture toughness; and (3) two different two-parameter (TP) methods: the average-stress (ASTP) method, which predicts failure when the average stress over a distance from the hole equals the laminate strength; and the point-stress (PSTP) Whitney-Nuismer (1974) approach, which predicts failure when the stress near the hole equals the material strength. The PSTP is relatively accurate and is by far the most widely used of all the prediction methods. However, for large ranges of variables and cases, the current strength predictions may not always be accurate.

Crews, J. H., Jr.↗
NASA NTRS1986

Optimized Bolted Joint

Computer technique aids joint optimization. Load-sharing between fasteners in multirow bolted composite joints computed by nonlinear-analysis computer program. Input to analysis was load-deflection data from 180 specimens tested as part of program to develop technology of structural joints for advanced transport aircraft. Bolt design optimization technique applicable to major joints in composite materials for primary and secondary structures and generally applicable for metal joints as well.

Hart-Smith, L. J.↗
NASA NTRS1986

Lubricating Holes for Corroded Nuts and Bolts

Corroded fasteners taken apart more easily. Lubricating holes bored to thread from three of flats. Holes facilitate application of penetrating oil to help loosen nut when rusted onto bolt. Holes make it possible to apply lubricants and rust removers directly to more of thread than otherwise reachable.

Penn, B. G.↗
NASA NTRS1985

The Alternating Surface Segmented Lap Joint: a Design for Thin Highly Loaded Joints

The combination of thin airfoil sections and high aerodynamic loads on many wind tunnel models presents a major problem for attachment of flap elements. Conventional methods of attaching fixed control elements such as lap and tongue-in-groove joints are not rigid enough to provide surface continuity required in high Reynolds number research. For the extreme cases, the solution has been to fabricate separate wings for each flap setting with the flap element being and integral part of the wing. Here an attractive solution to this problem, the alternating surface segmented lap joint, is discussed. This joint provides increased rigidity and lower stress levels than conventional joints. Additionally, attachment fastener loading is low and the joint can be designed to accommodate high shear levels due to bending without the use of dowel pins.

Watkins, V. E., Jr.↗
NASA NTRS1985

Initial Investigation of Cryogenic Wind Tunnel Model Filler Materials

Filler materials are used for surface flaws, instrumentation grooves, and fastener holes in wind tunnel models. More stringent surface quality requirements and the more demanding test environment encountered by cryogenic wind tunnels eliminate filler materials such as polyester resins, plaster, and waxes used on conventional wind tunnel models. To provide a material data base for cryogenic models, various filler materials are investigated. Surface quality requirements and test temperature extremes require matching of coefficients of thermal expansion or interfacing materials. Microstrain versus temperature curves are generated for several candidate filler materials for comparison with cryogenically acceptable materials. Matches have been achieved for aluminum alloys and austenitic steels. Simulated model surfaces are filled with candidate filler materials to determine finishing characteristics, adhesion and stability when subjected to cryogenic cycling. Filler material systems are identified which meet requirements for usage with aluminum model components.

Firth, G. C.↗
NASA NTRS1985

Recent developments in polyimide and bismaleimide adhesives

Research on high temperature resin systems has intensified. In the Aerospace Industry, the motivation for this increased activity has been to replace heat resistant alloys of aluminum, stainless steel and titanium by lighter weight glass and carbon fiber reinforced composites. Applications for these structures include: (1) engine nacelles involving long time exposure (thousands of hours) to temperatures in the 150 to 300 C range, (2) supersonic military aircraft involving moderately long exposure (hundreds of hours) to temperatures of 150 to 200 C, and (3) missile applications involving only brief exposure (seconds or minutes) to temperatures up to 500 C and above. Because of fatigue considerations, whenever possible, it is preferable to bond rather than mechanically fasten composite structures. For this reason, the increased usage of high temperature resin matrix systems for composites has necessitated the devlopment of compatible and equally heat stable adhesive systems. The performance of high temperature epoxy, epoxy phenolic and condensation polyimide adhesives is reviewed. This is followed by a discussion of three recently developed types of adhesives: (1) condensation reaction polyimides having improved processing characteristics; (2) addition reaction polyimides; and (3) bismaleimides.

Politi, R. E.↗
NASA NTRS1985

Design and construction of models for the National Transonic Facility, part 2

This lecture presents the results of fastener load and retention systems tests which were carried out as a part of the cryogenic models technology development program a the NASA Langley Research Center (LaRC). Various design concepts for the National Transonic Facility (NTF) developmental and production models are discussed. A number of NTF models are described with emphasis on materials used, uniqueness of design and design drivers. Design and fabrication experience is presented in terms of the primary thermal and mechanical considerations required for design as well as fabrication. Cost considerations are addressed in terms of factors influencing costs for NTF models and cost data comparisons which are taken from both NASA Langley and industry experience.

Young, C. P., Jr.↗
NASA NTRS1985

Segmented tubular cushion springs and spring assembly

A spring which includes a tube with an elliptical cross section, with the greater axial dimension extending laterally and the lesser axial dimension extending vertically is disclosed. A plurality of cuts in the form of slots passing through most of a wall of the tube extend perpendiculary to a longitudinal axis extending along the tube. An uncut portion of the tube wall extends along the tube for bonding or fastening the tube to a suitable base, such as a bottom of a seat cushion.

Haslim, L. A.↗
NASA NTRS1985

Self-locking double retention redundant full pin release

A double retention redundant pull pin release system is disclosed. The system responds to a single pull during an intentional release operation. A spiral threaded main pin is seated in a mating bore in a housing, which main pin has a flange fastened thereon at the part of the main pin which is exterior to the housing. Accidental release tends to rotate the main pin. A secondary pin passes through a slightly oversized opening in the flange and is seated in a second bore in the housing. The pins counteract against one another to prevent accidential release. A frictional lock is shared between the main and secondary pins to enhance further locking of the system. The secondary pin, in response to a first pull, is fully retracted from its bore and flange hole. Thereafter the pull causes the main pin to rotate free of the housing to release, for example, a parachute mechanism.

Killgrove, T. O.↗
NASA NTRS1984

Lightning protection guidelines and test data for adhesively bonded aircraft structures

The highly competitive marketplace and increasing cost of energy has motivated manufacturers of general aviation aircraft to utilize composite materials and metal-to-metal bonding in place of conventional fasteners and rivets to reduce weight, obtain smoother outside surfaces and reduce drag. The purpose of this program is protection of these new structures from hazardous lightning effects. The program began with a survey of advance-technology materials and fabrication methods under consideration for future designs. Sub-element specimens were subjected to simulated lightning voltages and currents. Measurements of bond line voltages, electrical sparking, and mechanical strength degradation were made to comprise a data base of electrical properties for new technology materials and basic structural configurations. The second hase of the program involved tests on full scale wing structures which contained integral fuel tanks and which were representative of examples of new technology structures and fuel systems. The purpose of these tests was to provide a comparison between full scale structural measurements and those obtained from the sub-element specimens.

Pryzby, J. E.↗
NASA NTRS1985

Analysis of a finite composite plate with smooth rigid pin

An elastic continuum method of analysis developed for a smooth rigid pin in a finite composite plate by using complex potentials that satisfy the governing orthotropic differential equation is presented. The plate is subjected to uniaxial loading and the nonlinear problems of partial contact in the pin-plate are studied. Three types of pin fits are examined: interference, push, and clearance. The problems of stresses due to pure interference, load contact behavior, and stresses variations are addressed. The effects of the rectangular geometry and the orthotropic property of the plate are demonstrated through numerical results. It is found that the use of large hole diameter/plate width ratios have deleterious effects and the use of interference has beneficial effects. The solutions obtained will help in the development of special finite elements for fastener joints. Finally, the boundary conditions on the finite outer boundaries are found to be satisfied by a successive integration technique.

Naidu, A. C. B.↗
NASA NTRS1985

Guidelines for structural verification and fracture control of Shuttle payloads

The procedures followed by the NASA Office of the Chief Engineer in developing the guidelines concerning the structures, materials, and fracture control of the Space Shuttle payloads are described. Factors controlling the payload launch safety, such as crew and passenger safety, reusability, and mixes of payloads in a single launch are emphasized. Special consideration is given to the STS design and testing approaches, materials considerations, safety criticality review processes, nondestructive evaluation inspection for STS payload fracture control, fracture mechanics screening procedures, and components of special concern (e.g., pressurized vessels, fasteners, and composite structures).

Lifer, C. E.↗
NASA NTRS1985

The design of repairable advanced composite structures

This paper addresses the repair of advanced composite structures by mechanical fasteners or by adhesive bonding. It is shown that many of today's composite designs are unreasonably difficult to repair. Conversely, the knowledge to design repairable structures is already available, if only it is applied during the initial design stage. Bolted or riveted repairs require only the avoidance of extremely orthotropic composite fiber patterns; those near the quasi-isotropic layup are the most suitable. Mildly orthotropic fiber patterns are appropriate for structures in which there is a dominant load direction. Thick composite structures are shown to require bolted or riveted repairs while thin structures favor adhesively bonded permanent repairs, although provisions can be easily made for temporary mechanical repairs. The reasons why integrally stiffened cocured composite designs are usually impractical to repair are explained and alternative repairable design concepts are presented.

Hart-Smith, L. J.↗
NASA NTRS1986

Vortex shedding from solid rocket propellant inhibitors

Vortex shedding frequency caused by the protrusion of inhibitors into the flow field of a solid rocket motor is investigated by experimental and mathematical models. The time dependent Navier-Stokes equations are solved using a finite difference technique assuming incompressible, two-dimensional flow under both laminar and turbulent flow conditions. For laminar flow, explicit solutions are obtained using a vorticity-transport equation in place of the Navier-Stokes equations. For turbulent flow, a two-equation (k-epsilon) model is used for turbulent modeling and the SIMPLE algorithm is employed as the computational scheme. Cold flow tests were conducted to confirm the basic flow structure and to determine the vortex shedding frequency under both laminar and turbulent flow conditions. The vortex shedding frequencies were determined using a stroboscope to measure the oscillating frequency of yarn tufts which were fastened to one inhibitor in the models. A hot-film anemometer established the velocity history behind the inhibitor. Good agreement between the theoretical results and measurements of the vortex shedding frequencies is demonstrated.

Shu, P. H.↗
NASA NTRS1987

Braking System for Wind Turbines

Operating turbine stopped smoothly by fail-safe mechanism. Windturbine braking systems improved by system consisting of two large steel-alloy disks mounted on high-speed shaft of gear box, and brakepad assembly mounted on bracket fastened to top of gear box. Lever arms (with brake pads) actuated by spring-powered, pneumatic cylinders connected to these arms. Springs give specific spring-loading constant and exert predetermined load onto brake pads through lever arms. Pneumatic cylinders actuated positively to compress springs and disengage brake pads from disks. During power failure, brakes automatically lock onto disks, producing highly reliable, fail-safe stops. System doubles as stopping brake and "parking" brake.

Krysiak, J. E.↗
NASA NTRS1987

Impact Driver With Integral Sliding Hammer

Tool combines impact driver with sliding dead-blow hammer. Used for any purpose for which ordinary impact driver used; tightening fasteners or driving starter holes for drill. Tool protects user from accidental injury and surrounding equipment from damage that might occur from ordinary arm-wielded hammer. Especially useful in underwater work.

Wallace, Bilby J.↗
NASA NTRS1987

Localized Densification of Tile for Impact Resistance

Densification process increases impact resistance of lightweight, porous silica tile without appreciably raising weight. Colloidal suspension of silica used to increase density of small portion of tile to be strengthened. Process controls penetration of suspension laterally and vertically so densification limited to volume where needed. Insures weight increased only minimally. See also "Attaching Metal Fasteners to Silica Tiles" (MSC-20537).

Smiser, Laurence W.↗
NASA NTRS1987

Heat Shields For Transatmospheric Vehicles

Thermal-protection schemes evaluated for space vehicles bouncing off Earth atmosphere. Report compares performances of four conceptual heat shields for transatmospheric vehicles. These future spacecraft will operate above atmosphere of Earth but will dip into atmosphere to exploit combinations of aerodynamic and propulsive forces for such major maneuvers as changing orbital planes. Will experience high rates of aerodynamic heating during such maneuvers. Three concepts based on insulating tile fastened to skin of vehicle. Fourth conceptual system includes multilayer insulating blanket under heat shield of FRCI.

Pitts, W. C.↗