Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “dynamic temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Dynamic modelling and control strategy of a temperature-driven metal hydride cooling system for buildings

A temperature-driven coupled metal hydride (MH) based thermal energy storage (TES) system can allow to shave and shift the peak energy demand in buildings. The high energy density and long-term (seasonal) energy storage capability are its major advantages over other energy storage methods. The dynamic nature of the MH operation, however, requires controlled hydrogen transfer between the coupled MHs at a rate needed to meet the building's transient load. While temperature-driven MH systems are studied in the literature, their application in buildings and control are scarcely reported. Here, this paper presents a control-based dynamic modeling of the temperature-driven coupled MH-TES system for building cooling applications. The dynamic model is developed in MATLAB(R) Simulink environment, considering the thermodynamic and kinetic behaviors of the MH systems. Based on a preliminary analysis of a property database of over 337 hydrides, we select around 1600 MH pairs suitable for building cooling applications. Each of these MH pairs is studied for their performance using the dynamic model, and among all, Zr 0.76 Ti 0.24 Ni 1.16 Mn 0.63 V 0.14 Fe 0.18 -Ti 0.85 Zr 0.15 Cr 1.2 Mn 0.8 MH pair showed fast dynamics along with high coefficient of performance (COP) of 0.71. A parametric investigation is performed on this MH pair to understand the effect of operating temperatures. Finally, three proportional-integral (PI) feedback controllers are investigated to regulate the temperature, pressure and mass exchange between the coupled MH pairs. The developed PI controller is sufficiently capable of rejecting the signal noise from the hydrogen flow and internal heat exchange processes with root mean square error of 5.78 W between reference and actual cooling load.

08 HYDROGEN↗
DOE OSTI2020

Fluid Behavior in Nanoporous Silica

We investigate dynamics of water (H 2 O) and methanol (CH 3 OH and CH 3 OD) inside mesoporous silica materials with pore diameters of 4.0, 2.5, and 1.5 nm using low-field (LF) nuclear magnetic resonance (NMR) relaxometry. Experiments were conducted to test the effects of pore size, pore volume, type of fluid, fluid/solid ratio, and temperature on fluid dynamics. Longitudinal relaxation times (T 1 ) and transverse relaxation times (T 2 ) were obtained for the above systems. We observe an increasing deviation in confined fluid behavior compared to that of bulk fluid with decreasing fluid-to-solid ratio. Our results show that the surface area-to-volume ratio is a critical parameter compared to pore diameter in the relaxation dynamics of confined water. An increase in temperature for the range between 25 and 50°C studied did not influence T 2 times of confined water significantly. However, when the temperature was increased, T 1 times of water confined in both silica-2.5 nm and silica-1.5 nm increased, while those of water in silica-4.0 nm did not change. Reductions in both T 1 and T 2 values as a function of fluid-to-solid ratio were independent of confined fluid species studied here. The parameter T 1 /T 2 indicates that H 2 O interacts more strongly with the pore walls of silica-4.0 nm than CH 3 OH and CH 3 OD.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1987

Properties of planetary fluids at high pressure and temperature

In order to derive models of the interiors of Uranus, Neptune, Jupiter and Saturn, researchers studied equations of state and electrical conductivities of molecules at high dynamic pressures and temperatures. Results are given for shock temperature measurements of N2 and CH4. Temperature data allowed demonstration of shock induced cooling in the the transition region and the existence of crossing isotherms in P-V space.

Nellis, W. J.↗
NASA NTRSDate not supplied

Modeling Entry Systems to Explore Our Solar System

Exploration of our Solar System is a foundational element of NASA’s identity. Delivering a scientific payload through an atmosphere to the surface of a planetary body requires safely navigating the extreme temperatures and stresses generated by flying many times the speed of sound. An entry system is the outer shell of a vehicle designed to protect the payload and, as a single point of failure for a mission, reliability is paramount. Unfortunately, it is not possible to fully replicate the flight environment in ground test facilities – so how do we confidently design a vehicle that needs to work the first time, every time? Modeling and simulation are critical tools for filling gaps in ground test capability and providing traceability from ground to flight. Modeling an entry system is a truly interdisciplinary effort, requiring knowledge of fluid dynamics, high-temperature chemistry, radiation, materials science, structural dynamics, guidance and control – and, finally, the mathematical and computing capability to pull it all together. In this talk, Dr. Michael Barnhardt will discuss the latest research in modeling entry systems and how it is being used in NASA’s exploration missions.

Entry systems↗
DOE OSTI2024

All-Perovskite Multicomponent Nanocrystal Superlattices

Nanocrystal superlattices (NC SLs) have long been sought as promising metamaterials, with nanoscale-engineered properties arising from collective and synergistic effects among the constituent building blocks. Lead halide perovskite (LHP) NCs come across as outstanding candidates for SL design, as they demonstrate collective light emission, known as superfluorescence, in single- and multicomponent SLs. Thus far, LHP NCs have only been assembled in single-component SLs or coassembled with dielectric NC building blocks acting solely as spacers between luminescent NCs. Here, we report the formation of multicomponent LHP NC-only SLs, i.e., using only CsPbBr 3 NCs of different sizes as building blocks. The structural diversity of the obtained SLs encompasses the ABO 6 , ABO 3 , and NaCl structure types, all of which contain orientationally and positionally locked NCs. For the selected model system, the ABO 6 -type SL, we observed efficient NC coupling and Förster-like energy transfer from strongly confined 5.3 nm CsPbBr 3 NCs to weakly confined 17.6 nm CsPbBr 3 NCs, along with characteristic superfluorescence features at cryogenic temperatures. Spatiotemporal exciton dynamics measurements reveal that binary SLs exhibit enhanced exciton diffusivity compared to single-component NC assemblies across the entire temperature range (from 5 to 298 K). The observed coherent and incoherent NC coupling and controllable excitonic transport within the solid NC SLs hold promise for applications in quantum optoelectronic devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

High-temperature active oxidation of nanocrystalline silicon-carbide: A reactive force-field molecular dynamics study

Flexible woven SiC ceramics are prone to accelerated fiber embrittlement under high temperature oxidation in dynamic oxygen environments. The nanocrystalline structure of the constituent fibers impacts the reaction kinetics and phase transformations during active oxidation. However, fundamental understanding and quantification of grain boundary effects on oxidation behavior in nanocrystalline SiC remain elusive when temperatures exceed 1500 K. This study deploys large-scale molecular dynamics simulations with a reactive force-field to elucidate the complex roles of atomic oxygen reservoir conditions and grain size on oxidation kinetics and the nature of oxides produced in both monocrystalline and nanocrystalline 3C-SiC between 1100 K and 2000 K. The simulations with dynamically replenished oxygen provide good agreement with oxidation kinetics and activation energies for the monocrystalline Si(100) and C(100) orientations published in the available literature. This study reveals that, by contrast, nanocrystalline SiC samples exhibit two distinct oxidation kinetics with a transition point at 1500 K due to surface melting, which is supported by experimental evidence. The introduction of a grain-boundary network produces a two-fold decrease in oxidation activation energies compared to monocrystalline SiC below 1500 K. Above 1500 K, however, the activation energies rise substantially due to the formation of a liquid Si phase at the SiC/Si oxide interface. Further, it is shown that the stability of the interfacial liquid phase is promoted by incoherent grain boundaries in the crystalline SiC. These findings are important for the deployment of nanocrystalline SiC fibers in advanced thermal protection systems for high-temperature applications.

36 MATERIALS SCIENCE↗
NASA NTRS1975

On the Navier-Stokes equations with constant total temperature

For various applications in fluid dynamics, it is assumed that the total temperature is constant. Therefore, the energy equation can be replaced by an algebraic relation. The resulting set of equations in the inviscid case is analyzed. It is shown that the system is strictly hyperbolic and well posed for the initial value problems. Boundary conditions are described such that the linearized system is well posed. The Hopscotch method is investigated and numerical results are presented.

Gottlieb, D.↗
NASA NTRS1976

On the Navier-Stokes equations with constant total temperature

For various applications in fluid dynamics, one can assume that the total temperature is constant. Therefore, the energy equations can be replaced by an algebraic relation. The resulting set of equations in the inviscid case is analyzed in this paper. It is shown that the system is strictly hyperbolic and well posed for the initial-value problem. Boundary conditions are described such that the linearized system is well posed. The hopscotch method is investigated and numerical results are presented.

Gottlieb, D.↗
NASA NTRS2015

An Assessment of Combustion Dynamics in a Low-Nox, Second-Generation Swirl-Venturi Lean Direct Injection Combustion Concept

Dynamic pressure measurements were taken during flame-tube emissions testing of three second-generation swirl-venturi lean direct injection (SV-LDI) combustor configurations. These measurements show that combustion dynamics were typically small. However, a small number of points showed high combustion dynamics, with peak-to-peak dynamic pressure fluctuations above 0.5 psi. High combustion dynamics occurred at low inlet temperatures in all three SV-LDI configurations, so combustion dynamics were explored further at low temperature conditions. A point with greater than 1.5 psi peak-to-peak dynamic pressure fluctuations was identified at an inlet temperature of 450!F, a pressure of 100 psia, an air pressure drop of 3%, and an overall equivalence ratio of 0.35. This is an off design condition: the temperature and pressure are typical of 7% power conditions, but the equivalence ratio is high. At this condition, the combustion dynamics depended strongly on the fuel staging. Combustion dynamics could be reduced significantly without changing the overall equivalence ratio by shifting the fuel distribution between stages. Shifting the fuel distribution also decreased NOx emissions.

low emissions combustors↗
DOE OSTI2024

Impact of composition and symmetry energy on the temperature of quasiprojectiles simulated with antisymmetrized molecular dynamics

The equation of state describes the emergent physical properties of matter. Experimental data is needed to help constrain the equation of state for nuclear matter. These constraints can help distinguish between an “asy-stiff” and an “asy-soft” equation of state, which has astrophysical implications. One path to help constrain the models is to analyze the nuclear caloric curve; some experiments have shown dependence on neutron excess, and may thus be sensitive to the asymmetry. A difference in the caloric curve based on the asymmetry of the reconstructed quasiprojectile (QP) had been observed using 70 Zn on 70 Zn at 35 MeV/nucleon taken with the NIMROD array. Antisymmetrized molecular dynamics calculations were performed for the same system and deexcited with gemini++. Both Gogny (asy-soft) and Gogny-as (asy-stiff) data sets were generated. The particles were then filtered based on detector geometric acceptance and thresholds. From the accepted particles, the excitation energy and temperature were calculated in the same way as for experimental data. Additionally, filter effects on the observed nuclear caloric curves were investigated. A tendency for the asy-stiff nuclear caloric curves to have higher temperatures than their asy-soft counterparts was observed for a number of probes. In addition, some probes may show sensitivity to the reconstructed composition of the QP, but this is inconclusive due to high statistical fluctuations and a large dependence on the exact method of event selection.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
NASA NTRS2011

SMOS/SMAP Synergy for SMAP Level 2 Soil Moisture Algorithm Evaluation

Soil Moisture Active Passive (SMAP) satellite has been proposed to provide global measurements of soil moisture and land freeze/thaw state at 10 km and 3 km resolutions, respectively. SMAP would also provide a radiometer-only soil moisture product at 40-km spatial resolution. This product and the supporting brightness temperature observations are common to both SMAP and European Space Agency's Soil Moisture and Ocean Salinity (SMOS) mission. As a result, there are opportunities for synergies between the two missions. These include exploiting the data for calibration and validation and establishing longer term L-band brightness temperature and derived soil moisture products. In this investigation we will be using SMOS brightness temperature, ancillary data, and soil moisture products to develop and evaluate a candidate SMAP L2 passive soil moisture retrieval algorithm. This work will begin with evaluations based on the SMOS product grids and ancillary data sets and transition to those that will be used by SMAP. An important step in this analysis is reprocessing the multiple incidence angle observations provided by SMOS to a global brightness temperature product that simulates the constant 40 degree incidence angle observations that SMAP will provide. The reprocessed brightness temperature data provide a basis for evaluating different SMAP algorithm alternatives. Several algorithms are being considered for the SMAP radiometer-only soil moisture retrieval. In this first phase, we utilized only the Single Channel Algorithm (SCA), which is based on the radiative transfer equation and uses the channel that is most sensitive to soil moisture (H-pol). Brightness temperature is corrected sequentially for the effects of temperature, vegetation, roughness (dynamic ancillary data sets) and soil texture (static ancillary data set). European Centre for Medium-Range Weather Forecasts (ECMWF) estimates of soil temperature for the top layer (as provided as part of the SMOS ancillary data) were used to correct for surface temperature effects and to derive microwave emissivity. ECMWF data were also used for precipitation forecasts, presence of snow, and frozen ground. Vegetation options are described below. One year of soil moisture observations from a set of four watersheds in the U.S. were used to evaluate four different retrieval methodologies: (1) SMOS soil moisture estimates (version 400), (2) SeA soil moisture estimates using the SMOS/SMAP data with SMOS estimated vegetation optical depth, which is part of the SMOS level 2 product, (3) SeA soil moisture estimates using the SMOS/SMAP data and the MODIS-based vegetation climatology data, and (4) SeA soil moisture estimates using the SMOS/SMAP data and actual MODIS observations. The use of SMOS real-world global microwave observations and the analyses described here will help in the development and selection of different land surface parameters and ancillary observations needed for the SMAP soil moisture algorithms. These investigations will greatly improve the quality and reliability of this SMAP product at launch.

Bindlish, Rajat↗
NASA NTRS1990

Acoustic testing of high temperature panels

Results are presented of a series of thermal-acoustic tests conducted on the NASA Langley Research Center Thermal-Acoustic Test Apparatus to (1) investigate techniques for obtaining strain measurements on metallic and carbon-carbon materials at elevated temperature; (2) document the dynamic strain response characteristics of several superalloy honeycomb thermal protection system panels at elevated temperatures of up to 1200 F; and (3) determine the strain response and sonic fatigue behavior of four carbon-carbon panels at both ambient and elevated temperatures. A second study tested four carbon-carbon panels to document panel dynamic response characteristics at ambient and elevated temperature, determine time to failure and faliure modes, and collect continuous strain data up to panel failure. Strain data are presented from both types of panels, and problems encountered in obtaining reliable strain data on the carbon-carbon panels are described. The failure modes of the carbon-carbon panels are examined.

Leatherwood, Jack D.↗
DOE OSTI2025

Creation and characterization of warm dense matter isochorically heated by an intense laser-driven proton beam to temperatures exceeding 100 eV

The warm dense matter (WDM) is an exotic state of matter encountered in inertial confinement implosions for fusion energy, as well as the interiors of giant planets like Jupiter, brown dwarfs, the atmospheres of white dwarfs, neutron star crusts, and newly discovered exo-planets. One efficient way to create WDM is to use protons accelerated by a high-intensity short-pulse laser to isochorically heat dense samples to WDM states. Despite its importance, direct temperature measurements within WDM targets are scarce. This study utilizes an intense proton beam generated by the kilojoule EP laser further focused and guided by a curved foil and cone structure to efficiently heat a thin copper sample. A high-resolution streaked spectrometer tuned to copper K α fluorescence lines provided bulk temperature measurements every ~2 ps, revealing temperatures exceeding 100 eV in under 50 ps. Particle-in-cell simulations of proton transport and energy deposition closely matched the observed heating dynamics, including transverse temperature gradients revealed by the broadening of K α lines.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Grizzly Development for Light Water Reactor and Advanced Reactor Applications in Fiscal Year 2021

This report summarizes work performed during Fiscal Year (FY) 2021 at Idaho National Laboratory (INL) for the U.S. Department of Energy’s Nuclear Engineering Advanced Modeling and Simulation (NEAMS) program for the Structural Materials and Chemistry Technical Area in the work package entitled “MS-21IN050106 - Structural Materials - INL.” This effort mainly focused on development and application of capabilities for engineering-scale analysis of nuclear reactor structural components in the Grizzly and BlackBear codes. These efforts include performance improvements and application of models for high-temperature component response, cluster dynamics modeling of precipitation in light water reactor pressure vessel steel, engineering-scale capability development in the areas of concrete simulation and reactor pressure vessel analysis, and preparation for and conducting an independent assessment of the adherence of these codes to software quality standards.

36 MATERIALS SCIENCE↗
NASA NTRS1985

Acoustic waves in the solar atmosphere. VII - Non-grey, non-LTE H(-) models

The propagation and shock formation of radiatively damped acoustic waves in the solar chromosphere are studied under the assumption that H(-) is the only absorber; the opacity is non-grey. Deviations from local thermodynamic equilibrium (LTE) are permitted. The results of numerical simulations show the depth dependence of the heating by the acoustic waves to be insensitive to the mean state of the atmosphere. After the waves have developed into shocks, their energy flux decays exponentially with a constant damping length of about 1.4 times the pressure scale height, independent of initial flux and wave period. Departures from LTE have a strong influence on the mean temperature structure in dynamical chromosphere models; this is even more pronounced in models with reduced particle density - simulating conditions in magnetic flux tubes - which show significantly increased temperatures in response to mechanical heating. When the energy dissipation of the waves is sufficiently large to dissociate most of the H(-) ions, a strong temperature rise is found that is reminiscent of the temperature structure in the transition zone between chromosphere and corona; the energy flux remaining in the waves then drives mass motions.

Schmitz, F.↗
NASA NTRS1992

The effect of solar cycle variations on the thermosphere

A review of current knowledge of the effect of solar activity on the thermosphere is presented. Data obtained by the Dynamics Explorer 2 spacecraft and model results from the NCAR Thermospheric GCM, which demonstrate the effect of increased solar and geomagnetic activity on composition, temperature and the dynamic structure of the upper atmosphere are discussed. It is shown how subtle change in the IMF can affect the form of the neutral gas circulation at high latitudes, with important implications for polar orbiting spacecraft.

Mccormac, F. G.↗
DOE OSTI2021

Nonadiabatic molecular dynamics analysis of hybrid Dion–Jacobson 2D leads iodide perovskites

The past six years have witnessed the rapid growth of interest in Dion–Jacobson (DJ) phase two-dimensional (2D) hybrid halide perovskites as optoelectronic materials with considerable intrinsic stability. The precise relationships between structural variations and the resulting charge carrier dynamics at finite temperature in these materials are keys to practical applications and are not yet completely understood. Here, we study 3-(aminomethyl) piperidinium (3AMP) and 4-(aminomethyl) piperidinium (4AMP) spacer cation-based lead iodide DJ phase systems and find these spacer cations to have a profound impact on the structural dynamics. Particularly, large conformational dynamics of the 3AMP-based perovskite compared to that of the 4AMP at room temperature leads to pronounced state energy fluctuation near band edges and further results in a shorter quantum coherence. The faster quantum decoherence of the 3AMP spacer-based perovskite underpins a longer nonradiative lifetime, offering insight into its superior performance as an optoelectronic material. This work sheds light on the relationship between structural fluctuations and charge carrier dynamics that can help in designing 2D perovskites with superior photophysical properties.

Wang, Ying (ORCID:0000000349048227)↗
DOE OSTI2022

Long-Term Static and Dynamic Corrosion Stability of Nonwetting Surfaces

Superhydrophobic surfaces (SHSs) and lubricant-infused surfaces (LISs) are two classes of nonwetting surfaces that have drawn attention due to their advanced functional properties including corrosion inhibition. Yet there is a conspicuous lack of corrosion study of SHSs and LISs with respect to their fabrication and material parameters, especially at high temperatures and under dynamic flow conditions over long durations, which is sought to be addressed in this article. Considering copper SHSs and LISs, a full factorial combinatorial study of two facile texturing processes, electrodeposition and etching, two different functionalization agents, stearic acid and mercaptan, and two types of infused lubricants, Krytox 104 and DOWSIL 510, is presented, encompassing over 650 measurements on 90 tested surfaces. All fabricated surfaces demonstrated water repellency with a contact angle above 150° and a sliding angle below 7°. For the first time, the study examines high-temperature corrosion stability and long-term corrosion durability of the nonwetting surfaces in both static fluid and dynamic turbulent flow conditions over a period of 30 days. Here, LISs and SHSs are shown to provide excellent corrosion inhibition over all tested corrosion conditions, with negligible presence of corrosion species on the surfaces and no deterioration of the texturing. The surfaces are also shown to rejuvenate easily to the initial wettability and corrosion resistance values. This study provides valuable insights into the selection of materials and processing parameters for the fabrication of nonwetting surfaces for the application of interest.

Copper↗