SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Photomicroscopy system, with simple optics and any standard microscope objective, is used with any type of motion picture, still, or television camera system. Device performs well under difficult environmental conditions and applies to work in ecological studies, field hospitals, and geological surveys.
Data are presented that indicate that heat-treated Czochralski-grown aluminum doped silicon that undergoes an appreciable resistivity increase during heating at approximately 450 C is significantly more resistant to both neutron and gamma irradiation than boron doped material (or aluminum doped material that either has not been heat treated or does not experience an appreciable resistivity change during such a treatment). Data interpretation is, however, quite difficult due to the occurrence of severe trapping effects in heat treated material.
All astronaut maneuvering unit systems used during the Gemini 9 mission were in an acceptable condition for flight when the evaluation was terminated. Some difficulty was experienced with reception of the voice signal by the command pilot. All of the donning provisions are apparently practical in the orbital environment; however, the donning activities were more difficult to perform than had been experienced in the one-g and zero-g training exercises. Lighting was marginal because of the failure of one adapter floodlight and one penlight. The crewmembers reported a tendency for the extravehicular activity pilot and any loose equipment to move outward from the earth relative to the spacecraft. This tendency affected activities at a work station and maneuvering in an extravehicular environment.
The quasi-Monte Carlo method of integration offers an attractive solution to the problem of evaluating integrals in a large number of dimensions; however, the associated error bounds are difficult to obtain theoretically. Since these bounds are associated with the L2 discrepancy of the set of points used in the integration. Numerical calculations of the L2 discrepancy for several types of quasi-Monte Carlo formulae are presented.
Computerized techniques and methods were used to conduct preliminary soil and crop identification experiments. The soil identification experiment was conducted by making densitometer measurements on Ektachrome infrared film exposed at 14,000 feet. The density measurements were analyzed by plotting sample probability density functions, two-dimensional scatter plots, and the use of K-class I to determine the complete set of classification results for one, two, three and four features. Due to the presence of nineteen classes, crop identification experiments were more difficult to formulate. Classes of corn, fallow, harvested wheat, roadways, trees and water were classified 75 percent correct.
The strong influence NASA-sponsored research has had on the development of solutions to difficult contamination problems is considered. The contamination control field is comprised of an industrial base, supplying the tools of control; a user base, adopting control techniques; and a technical base, expanding the concepts of control. Both formal and informal mechanisms used by NASA to communicate a variety of technical advances are reviewed and certain examples of the expansion of the user base through technology transfer are given. Issues related to transfer of NASA-generated contamination control technology are emphasized.
The abstract theory presented shows how the theory of dissipative systems of ordinary differential equations can be extended to include a wide class of functional and partial differential equations. Since the basic hypotheses are all in terms of boundedness, finding sufficient conditions in terms of Liapunov functions was not difficult. Work is being undertaken to solve some nontrivial examples to illustrate how the theory can applied.
The results are discussed in terms of the meteorological data acquisition procedures necessary to monitor changes in atmospheric parameters to support aircraft flyover noise measurements and aircraft noise certification programs. The data consisted primarily of sequential radiosonde ascents to approximately 5000 ft spaced some half-hour to an hour apart. The weather covered by the data sample was predominantly that of clear skies and calm-to-light surface winds associated with well established high-pressure systems. Under these restrictive weather conditions, the study shows that the largest variabilities in temperature and humidity occur during the early morning hours resulting from the effects of direct solar heating of the surface. These rapid changes apparently do not penetrate above approximately 1000 ft. In the late morning hours, the atmosphere appears to become stabilized so that net changes in temperatures and relative humidities at all levels are insignificant even in time periods exceeding three hours. By noon, however, turbulent fluctuations in surface wind and the wind speed itself increase to levels which would make the microphone recording of acoustic signals in the field difficult.
The development of the test/analysis technique known as the impulse transfer function (ITF) method is discussed. This technique, when implemented with proper data processing systems, should become a valuable supplement to conventional dynamic testing and analysis procedures that will be used in the space shuttle development program. The method can relieve many of the problems associated with extensive and costly testing of the shuttle for transient loading conditions. In addition, the time history information derived from impulse testing has the potential for being used to determine modal data for the structure under investigation. The technique could be very useful in determining the time-varying modal characteristics of structures subjected to thermal transients, where conventional mode surveys are difficult to perform.
A cost study was made to assess the potential of the large-scale use of solar cell power for terrestrial applications. The incentive is the attraction of a zero-pollution source of power for wide-scale use. Unlike many other concepts for low-pollution power generation, even thermal pollution is avoided since only the incident solar flux is utilized. To provide a basis for comparison and a perspective for evaluation, the pertinent technology was treated in two categories: current and optimistic. Factors considered were solar cells, array assembly, power conditioning, site preparation, buildings, maintenance, and operation. The capital investment was assumed to be amortized over 30 years. The useful life of the solar cell array was assumed to be 10 years, and the cases of zero and 50-percent performance deg-radation were considered. Land costs, taxes, and profits were not included in this study because it was found too difficult to provide good generalized estimates of these items. On the basis of the factors considered, it is shown that even for optimistic projections of technology, electric power from large-sclae terrestrial use of solar cells is approximately two to three orders of magnitude more costly than current electric power generation from either fossil or nuclear fuel powerplants. For solar cell power generation to be a viable competitor on a cost basis, technological breakthroughs would be required in both solar cell and array fabrication and in site preparation.
The metallurgical structure and some of the mechanical properties of two cobalt alloys, cobalt-50% iron and cobalt-25% molybdenum-10% chromium, were determined under various heat treated conditions. The mechanical properties of the bcc disordered Co-50Fe alloy, which was found to be very brittle, indicated an exceedingly low fracture strength, low hardness, and very weak grain boundary strength. Ordering by suitable heat treatment only produced a more brittle material with a lower fracture strength and a slightly higher hardness value. Work hardening was found to produce a finer grain structure and a greater grain boundary strength. Tensile properties were examined. It was found that the Co-25Mo-10Cr alloy was difficult to place in the alpha Co solid solution condition, which limited the ability to use precipitation as a hardening reaction. Over two hundred adhesion cycles from zero contact load, to maximum load, to fracture were conducted between couples for each of the above alloys in an ultrahigh vacuum system which would permit the sample surfaces to be cleaned of all contaminant layers. In the Co-50Fe case, the calculated fracture stress from the adhesion tests showed values in the range of 80 to 150 k.s.i., which is about ten times greater than the values from tension tests.
Techniques for obtaining quantitative information about boundedness properties are developed and applied to the sampled-data control of satellite attitude with quantization. Relevant stability concepts are introduced as a series of definitions, and interrelationships between various definitions are discussed. The boundedness regions are estimated by means of quadratic Liapunov functions, and a sufficient condition for the existence of a boundedness region is given for a certain class of systems. A quadratic Liapunov function is applied to the Lur'e-Postinkov class of systems, where the linear part of the system is not asymptotically stable and the quantizer represents the nonlinear characteristic. A numerical calculation of the region of boundedness estimates is performed for satellite attitude control and is compared with simulation results. It is tentatively concluded that the Liapunov results may be good and that simulation results may be difficult to interpret and time-consuming to generate. The Lur'e-based technique yields estimates of regions of absolute boundedness, but at the cost of greater analytical complexity.
A unified and rational treatment of the theory of fiber reinforced composite materials is presented. Fundamental geometric and elasticity considerations are throughly covered, and detailed derivations of the effective elastic moduli for these materials are presented. Biaxially reinforced materials which take the form of laminates are then discussed. Based on the fundamentals presented in the first portion of this volume, the theory of fiber-reinforced composite materials is extended to include viscoelastic and thermoelastic properties. Thermal and electrical conduction, electrostatics and magnetostatics behavior of these materials are discussed. Finally, a brief statement of the very difficult subject of physical strength is included.
The flying qualities of the CV-990 jet transport were evaluated over the normal operating flight envelope and in smooth air to provide baseline data for transport airplanes. Pilot ratings of airplane handling characteristics for specific test conditions and configurations from approach to normal cruise were compared with various flying qualities criteria. In general, the CV-990 flying qualities were evaluated as satisfactory, and the evaluations supported transport flying qualities criteria. The Dutch roll damping was rated more satisfactory than was predicted by the flying qualities criteria. The pilots found rudder coordination for the yaw generated during high roll rates very difficult. They preferred to control with roll and pitch controls and to use the yaw damper to provide the required rudder coordination.
A computer simulation of a remote manipulation task and a rate-controlled manipulator is described. Some low-level automatic decision making ability which could be used at the operator's discretion to augment his direct continuous control was built into the manipulator. Experiments were made on the effect of transmission delay, dynamic lag, and intermittent vision on human manipulative ability. Delay does not make remote manipulation impossible. Intermittent visual feedback, and the absence of rate information in the display presented to the operator do not seem to impair the operator's performance. A small-capacity visual feedback channel may be sufficient for remote manipulation tasks, or one channel might be time-shared between several operators. In other experiments the operator called in sequence various on-site automatic control programs of the machine, and thereby acted as a supervisor. The supervisory mode of operation has some advantages when the task to be performed is difficult for a human controlling directly.
Instrumentation developed for studies of path behavior of the green sea turtle and migration movement of polar bear is described. Preliminary results bearing on navigation ability in these species are presented. Both species operate in difficult environments, and the problems faced in the design of electronic instrumentation for these studies are not completely specified at this time. However, the critical factors yet to be understood are primarily related to the behavior of instrumented animals. The data obtained with these experimental techniques are included, first to illustrate the technique and, second to provide initial preliminary results bearing on animal navigation.
A solid state film transport utilizing piezoelectric motion was evaluated and found to have potential in film positioning applications. The concept is particularly useful in flight equipment where torque motors and conventional transport mechanisms are difficult to apply. A demonstration model utilizing 5-inch film was designed, tested, and evaluated. Three basic operating modes were investigated. Design goals for step size were achieved under controlled conditions. The continuous mode test results were marred by an inability to transfer efficiently the piezoceramic motion to the film itself. The design, test results, and problem areas are described.
It has been widely suggested that space photography may be used for updating maps of transportation networks. Proponents of the argument have suggested that color space photographs of the resolution obtained with Hasselblad 80 mm lenses (about 300 feet) contain enough useful information to update the extensions of major U. S. highways. The present study systematically documents for the Dallas-Fort Worth area the potential of such space photography in detecting, and to a lesser degree identifying, the existing road networks. Color separation plates and an enlargement of the color photograph were produced and all visible roads traced onto transparencies for study. Major roads and roads under construction were the most visible while lower class roads and roads in urban areas had the poorest return. Road width and classification were found to be the major determinant in visibility, varying from 100 per cent visible for divided highways to 15 per cent visible of bladed earth roads. In summary, space photographs of this resolution proved to be difficult to use for accurate road delineation. Only super highways in rural areas with the greatest road-width were completely identifiable, the width being about 1/3 that of the resolution cell.